From e9a20171dfa0aa134d2211126d1310f2daea52cf Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 17 Dec 2009 13:01:36 +0200 Subject: USB: otg: add notifier support The notifier will be used to communicate usb events to other drivers like the charger chip. This can be used as source of information to kick usb charger detection as described by the USB Battery Charging Specification 1.1 and/or to pass bMaxPower field of selected usb_configuration to charger chip in order to use that information as input current on the charging profile setup. Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/otg.h | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) (limited to 'include/linux/usb') diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h index 52bb917641f0..6c0b676b27d8 100644 --- a/include/linux/usb/otg.h +++ b/include/linux/usb/otg.h @@ -9,6 +9,8 @@ #ifndef __LINUX_USB_OTG_H #define __LINUX_USB_OTG_H +#include + /* OTG defines lots of enumeration states before device reset */ enum usb_otg_state { OTG_STATE_UNDEFINED = 0, @@ -33,6 +35,14 @@ enum usb_otg_state { OTG_STATE_A_VBUS_ERR, }; +enum usb_xceiv_events { + USB_EVENT_NONE, /* no events or cable disconnected */ + USB_EVENT_VBUS, /* vbus valid event */ + USB_EVENT_ID, /* id was grounded */ + USB_EVENT_CHARGER, /* usb dedicated charger */ + USB_EVENT_ENUMERATED, /* gadget driver enumerated */ +}; + #define USB_OTG_PULLUP_ID (1 << 0) #define USB_OTG_PULLDOWN_DP (1 << 1) #define USB_OTG_PULLDOWN_DM (1 << 2) @@ -70,6 +80,9 @@ struct otg_transceiver { struct otg_io_access_ops *io_ops; void __iomem *io_priv; + /* for notification of usb_xceiv_events */ + struct blocking_notifier_head notifier; + /* to pass extra port status to the root hub */ u16 port_status; u16 port_change; @@ -203,6 +216,18 @@ otg_start_srp(struct otg_transceiver *otg) return otg->start_srp(otg); } +/* notifiers */ +static inline int +otg_register_notifier(struct otg_transceiver *otg, struct notifier_block *nb) +{ + return blocking_notifier_chain_register(&otg->notifier, nb); +} + +static inline void +otg_unregister_notifier(struct otg_transceiver *otg, struct notifier_block *nb) +{ + blocking_notifier_chain_unregister(&otg->notifier, nb); +} /* for OTG controller drivers (and maybe other stuff) */ extern int usb_bus_start_enum(struct usb_bus *bus, unsigned port_num); -- cgit v1.2.3 From 5d3987796c7a747e5ed3ded1eb64a9632d52a1a4 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Fri, 18 Dec 2009 12:14:21 +0100 Subject: USB: storage: Never reset devices that will morph to an old mode Some devices must be switched to a new mode to fully use them. A reset would make them revert to the old mode. Therefore a reset must not be used for error handling with such devices. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/quirks.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/linux/usb') diff --git a/include/linux/usb/quirks.h b/include/linux/usb/quirks.h index 2526f3bbd273..0a555dd131fc 100644 --- a/include/linux/usb/quirks.h +++ b/include/linux/usb/quirks.h @@ -19,4 +19,7 @@ /* device can't handle its Configuration or Interface strings */ #define USB_QUIRK_CONFIG_INTF_STRINGS 0x00000008 +/*device will morph if reset, don't use reset for handling errors */ +#define USB_QUIRK_RESET_MORPHS 0x00000010 + #endif /* __LINUX_USB_QUIRKS_H */ -- cgit v1.2.3 From 551cdbbeb118bd5ed301f8749aef69219284399b Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Thu, 14 Jan 2010 11:08:04 -0800 Subject: USB: rename USB_SPEED_VARIABLE to USB_SPEED_WIRELESS It's really the wireless speed, so rename the thing to make more sense. Based on a recommendation from David Vrabel Cc: David Vrabel Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/ch9.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux/usb') diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h index 94012e649d86..e58369ff8168 100644 --- a/include/linux/usb/ch9.h +++ b/include/linux/usb/ch9.h @@ -775,7 +775,7 @@ enum usb_device_speed { USB_SPEED_UNKNOWN = 0, /* enumerating */ USB_SPEED_LOW, USB_SPEED_FULL, /* usb 1.1 */ USB_SPEED_HIGH, /* usb 2.0 */ - USB_SPEED_VARIABLE, /* wireless (usb 2.5) */ + USB_SPEED_WIRELESS, /* wireless (usb 2.5) */ USB_SPEED_SUPER, /* usb 3.0 */ }; -- cgit v1.2.3 From 5fc4e77911f457b6aa910c704eebe3a58d334116 Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Mon, 28 Dec 2009 13:40:42 +0200 Subject: usb: musb: Add 'extvbus' in musb_hdrc_platform_data Some of the board might use external Vbus power supply on musb interface which would require to program ULPI_BUSCONTROL register. Adding 'extvbus' flag which can be set from such boards which will be checked at musb driver files before programming ULPI_BUSCONTROL. Signed-off-by: Ajay Kumar Gupta Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/musb.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/linux/usb') diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h index d43755669261..4b7f8fa252f0 100644 --- a/include/linux/usb/musb.h +++ b/include/linux/usb/musb.h @@ -76,6 +76,9 @@ struct musb_hdrc_platform_data { /* (HOST or OTG) msec/2 after VBUS on till power good */ u8 potpgt; + /* (HOST or OTG) program PHY for external Vbus */ + unsigned extvbus:1; + /* Power the device on or off */ int (*set_power)(int state); -- cgit v1.2.3 From c58bfa6b97731590e42cba6bd13829c4e480992f Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 21 Jan 2010 15:33:55 +0200 Subject: USB: musb: deprecate what we don't use after 2.6.34, those fields will be removed from struct musb_hdrc_platform_data, it's expected that other architectures are fixed by then. Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/musb.h | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'include/linux/usb') diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h index 4b7f8fa252f0..8e0f2bc8d8c9 100644 --- a/include/linux/usb/musb.h +++ b/include/linux/usb/musb.h @@ -30,26 +30,26 @@ struct musb_hdrc_eps_bits { struct musb_hdrc_config { /* MUSB configuration-specific details */ unsigned multipoint:1; /* multipoint device */ - unsigned dyn_fifo:1; /* supports dynamic fifo sizing */ - unsigned soft_con:1; /* soft connect required */ - unsigned utm_16:1; /* utm data witdh is 16 bits */ + unsigned dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */ + unsigned soft_con:1 __deprecated; /* soft connect required */ + unsigned utm_16:1 __deprecated; /* utm data witdh is 16 bits */ unsigned big_endian:1; /* true if CPU uses big-endian */ unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */ unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */ unsigned high_iso_tx:1; /* Tx ep required for HB iso */ unsigned high_iso_rx:1; /* Rx ep required for HD iso */ - unsigned dma:1; /* supports DMA */ - unsigned vendor_req:1; /* vendor registers required */ + unsigned dma:1 __deprecated; /* supports DMA */ + unsigned vendor_req:1 __deprecated; /* vendor registers required */ u8 num_eps; /* number of endpoints _with_ ep0 */ - u8 dma_channels; /* number of dma channels */ + u8 dma_channels __deprecated; /* number of dma channels */ u8 dyn_fifo_size; /* dynamic size in bytes */ - u8 vendor_ctrl; /* vendor control reg width */ - u8 vendor_stat; /* vendor status reg witdh */ - u8 dma_req_chan; /* bitmask for required dma channels */ + u8 vendor_ctrl __deprecated; /* vendor control reg width */ + u8 vendor_stat __deprecated; /* vendor status reg witdh */ + u8 dma_req_chan __deprecated; /* bitmask for required dma channels */ u8 ram_bits; /* ram address size */ - struct musb_hdrc_eps_bits *eps_bits; + struct musb_hdrc_eps_bits *eps_bits __deprecated; #ifdef CONFIG_BLACKFIN /* A GPIO controlling VRSEL in Blackfin */ unsigned int gpio_vrsel; -- cgit v1.2.3 From 640e95abdfae9fef5949084c92e80c8f2f8b5ec5 Mon Sep 17 00:00:00 2001 From: Eirik Aanonsen Date: Fri, 5 Feb 2010 09:49:25 +0100 Subject: USB: atmel uaba: Adding invert vbus_pin Adding vbus_pin_inverted so that the usb detect pin can be active high or low depending on HW implementation also replaced the gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This allows the driver to be loaded and save about 0,15W on the consumption. Signed-off-by: Eirik Aanonsen Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/atmel_usba_udc.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux/usb') diff --git a/include/linux/usb/atmel_usba_udc.h b/include/linux/usb/atmel_usba_udc.h index 6311fa2d9f82..baf41c8616e9 100644 --- a/include/linux/usb/atmel_usba_udc.h +++ b/include/linux/usb/atmel_usba_udc.h @@ -15,6 +15,7 @@ struct usba_ep_data { struct usba_platform_data { int vbus_pin; + int vbus_pin_inverted; int num_ep; struct usba_ep_data ep[0]; }; -- cgit v1.2.3 From efcbd3df079a6f8a8a2d5207c4e8429e02356c79 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Fri, 5 Feb 2010 18:09:49 -0800 Subject: USB: Extend and neaten dbg macros Add format/argument validation for #ifndef DEBUG dbg macro Neaten dbg macro definitions Signed-off-by: Joe Perches Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/serial.h | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) (limited to 'include/linux/usb') diff --git a/include/linux/usb/serial.h b/include/linux/usb/serial.h index 1819396ed501..0a458b861933 100644 --- a/include/linux/usb/serial.h +++ b/include/linux/usb/serial.h @@ -351,14 +351,11 @@ static inline void usb_serial_debug_data(int debug, /* Use our own dbg macro */ #undef dbg -#define dbg(format, arg...) \ - do { \ - if (debug) \ - printk(KERN_DEBUG "%s: " format "\n" , __FILE__ , \ - ## arg); \ - } while (0) - - +#define dbg(format, arg...) \ +do { \ + if (debug) \ + printk(KERN_DEBUG "%s: " format "\n", __FILE__, ##arg); \ +} while (0) #endif /* __LINUX_USB_SERIAL_H */ -- cgit v1.2.3 From 6d61ae9112960a2b3ed3360602dfb3bfd357954f Mon Sep 17 00:00:00 2001 From: Dennis O'Brien Date: Mon, 15 Feb 2010 08:50:38 -0800 Subject: USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers This patch removes the vstusb driver and support from the Linux tree. This driver provided support for Vernier Software & Technology devices and spectrometers (Ocean Optics). This driver is being replaced by a user space - libusb - implementation. Signed-off-by: Jim Collar Signed-off-by: Greg Kroah-Hartman --- include/linux/usb/Kbuild | 1 - include/linux/usb/vstusb.h | 71 ---------------------------------------------- 2 files changed, 72 deletions(-) delete mode 100644 include/linux/usb/vstusb.h (limited to 'include/linux/usb') diff --git a/include/linux/usb/Kbuild b/include/linux/usb/Kbuild index 54c446309a2a..29fd73b0bffc 100644 --- a/include/linux/usb/Kbuild +++ b/include/linux/usb/Kbuild @@ -5,4 +5,3 @@ header-y += gadgetfs.h header-y += midi.h header-y += g_printer.h header-y += tmc.h -header-y += vstusb.h diff --git a/include/linux/usb/vstusb.h b/include/linux/usb/vstusb.h deleted file mode 100644 index 1cfac67191ff..000000000000 --- a/include/linux/usb/vstusb.h +++ /dev/null @@ -1,71 +0,0 @@ -/***************************************************************************** - * File: drivers/usb/misc/vstusb.h - * - * Purpose: Support for the bulk USB Vernier Spectrophotometers - * - * Author: EQware Engineering, Inc. - * Oregon City, OR, USA 97045 - * - * Copyright: 2007, 2008 - * Vernier Software & Technology - * Beaverton, OR, USA 97005 - * - * Web: www.vernier.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - *****************************************************************************/ -/***************************************************************************** - * - * The vstusb module is a standard usb 'client' driver running on top of the - * standard usb host controller stack. - * - * In general, vstusb supports standard bulk usb pipes. It supports multiple - * devices and multiple pipes per device. - * - * The vstusb driver supports two interfaces: - * 1 - ioctl SEND_PIPE/RECV_PIPE - a general bulk write/read msg - * interface to any pipe with timeout support; - * 2 - standard read/write with ioctl config - offers standard read/write - * interface with ioctl configured pipes and timeouts. - * - * Both interfaces can be signal from other process and will abort its i/o - * operation. - * - * A timeout of 0 means NO timeout. The user can still terminate the read via - * signal. - * - * If using multiple threads with this driver, the user should ensure that - * any reads, writes, or ioctls are complete before closing the device. - * Changing read/write timeouts or pipes takes effect on next read/write. - * - *****************************************************************************/ - -struct vstusb_args { - union { - /* this struct is used for IOCTL_VSTUSB_SEND_PIPE, * - * IOCTL_VSTUSB_RECV_PIPE, and read()/write() fops */ - struct { - void __user *buffer; - size_t count; - unsigned int timeout_ms; - int pipe; - }; - - /* this one is used for IOCTL_VSTUSB_CONFIG_RW */ - struct { - int rd_pipe; - int rd_timeout_ms; - int wr_pipe; - int wr_timeout_ms; - }; - }; -}; - -#define VST_IOC_MAGIC 'L' -#define VST_IOC_FIRST 0x20 -#define IOCTL_VSTUSB_SEND_PIPE _IO(VST_IOC_MAGIC, VST_IOC_FIRST) -#define IOCTL_VSTUSB_RECV_PIPE _IO(VST_IOC_MAGIC, VST_IOC_FIRST + 1) -#define IOCTL_VSTUSB_CONFIG_RW _IO(VST_IOC_MAGIC, VST_IOC_FIRST + 2) -- cgit v1.2.3 From 2b9ddcb8b2ce6a44f0f969000f16b016caa64294 Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Thu, 4 Mar 2010 19:46:18 +0100 Subject: ALSA: usb/audio.h: Fix field order Signed-off-by: Daniel Mack Cc: Clemens Ladisch Signed-off-by: Takashi Iwai --- include/linux/usb/audio.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux/usb') diff --git a/include/linux/usb/audio.h b/include/linux/usb/audio.h index 6bb293684eb8..4d3e450e2b03 100644 --- a/include/linux/usb/audio.h +++ b/include/linux/usb/audio.h @@ -269,8 +269,8 @@ struct uac_format_type_i_ext_descriptor { __u8 bLength; __u8 bDescriptorType; __u8 bDescriptorSubtype; - __u8 bSubslotSize; __u8 bFormatType; + __u8 bSubslotSize; __u8 bBitResolution; __u8 bHeaderLength; __u8 bControlSize; -- cgit v1.2.3