From d6ea3df0d470fb9260db93883f97764cf9f0e562 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Wed, 24 Nov 2010 10:17:14 +0100
Subject: spi/pxa2xx: Add CE4100 support

Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
---
 include/linux/spi/pxa2xx_spi.h | 105 ++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 104 insertions(+), 1 deletion(-)

(limited to 'include/linux')

diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h
index 471ed6889113..d3e1075f7b60 100644
--- a/include/linux/spi/pxa2xx_spi.h
+++ b/include/linux/spi/pxa2xx_spi.h
@@ -19,7 +19,6 @@
 #define __linux_pxa2xx_spi_h
 
 #include <linux/pxa2xx_ssp.h>
-#include <mach/dma.h>
 
 #define PXA2XX_CS_ASSERT (0x01)
 #define PXA2XX_CS_DEASSERT (0x02)
@@ -44,6 +43,110 @@ struct pxa2xx_spi_chip {
 	void (*cs_control)(u32 command);
 };
 
+#ifdef CONFIG_ARCH_PXA
+
+#include <linux/clk.h>
+#include <mach/dma.h>
+
 extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
 
+#else
+/*
+ * This is the implemtation for CE4100 on x86. ARM defines them in mach/ or
+ * plat/ include path.
+ * The CE4100 does not provide DMA support. This bits are here to let the driver
+ * compile and will never be used. Maybe we get DMA support at a later point in
+ * time.
+ */
+
+#define DCSR(n)         (n)
+#define DSADR(n)        (n)
+#define DTADR(n)        (n)
+#define DCMD(n)         (n)
+#define DRCMR(n)        (n)
+
+#define DCSR_RUN	(1 << 31)	/* Run Bit */
+#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch */
+#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable */
+#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
+#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
+#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt */
+#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt */
+#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt */
+
+#define DCSR_EORIRQEN	(1 << 28)	/* End of Receive Interrupt Enable */
+#define DCSR_EORJMPEN	(1 << 27)	/* Jump to next descriptor on EOR */
+#define DCSR_EORSTOPEN	(1 << 26)	/* STOP on an EOR */
+#define DCSR_SETCMPST	(1 << 25)	/* Set Descriptor Compare Status */
+#define DCSR_CLRCMPST	(1 << 24)	/* Clear Descriptor Compare Status */
+#define DCSR_CMPST	(1 << 10)	/* The Descriptor Compare Status */
+#define DCSR_EORINTR	(1 << 9)	/* The end of Receive */
+
+#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid */
+#define DRCMR_CHLNUM	0x1f		/* mask for Channel Number */
+
+#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor */
+#define DDADR_STOP	(1 << 0)	/* Stop */
+
+#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
+#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
+#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
+#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
+#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
+#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
+#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
+#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
+#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
+#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
+#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
+#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
+#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
+#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
+
+/*
+ * Descriptor structure for PXA's DMA engine
+ * Note: this structure must always be aligned to a 16-byte boundary.
+ */
+
+typedef enum {
+	DMA_PRIO_HIGH = 0,
+	DMA_PRIO_MEDIUM = 1,
+	DMA_PRIO_LOW = 2
+} pxa_dma_prio;
+
+/*
+ * DMA registration
+ */
+
+static inline int pxa_request_dma(char *name,
+		pxa_dma_prio prio,
+		void (*irq_handler)(int, void *),
+		void *data)
+{
+	return -ENODEV;
+}
+
+static inline void pxa_free_dma(int dma_ch)
+{
+}
+
+/*
+ * The CE4100 does not have the clk framework implemented and SPI clock can
+ * not be switched on/off or the divider changed.
+ */
+static inline void clk_disable(struct clk *clk)
+{
+}
+
+static inline int clk_enable(struct clk *clk)
+{
+	return 0;
+}
+
+static inline unsigned long clk_get_rate(struct clk *clk)
+{
+	return 3686400;
+}
+
+#endif
 #endif
-- 
cgit v1.2.3