From 29cbe68c516a48a9a88b3226878570c6cbd83c02 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 3 Dec 2010 09:20:44 +0100 Subject: cfg80211/mac80211: add mesh join/leave commands Instead of tying mesh activity to interface up, add join and leave commands for mesh. Since we must be backward compatible, let cfg80211 handle joining a mesh if a mesh ID was pre-configured when the device goes up. Note that this therefore must modify mac80211 as well since mac80211 needs to lose the logic to start the mesh on interface up. We now allow querying mesh parameters before the mesh is connected, which simply returns defaults. Setting them (internally renamed to "update") is only allowed while connected. Specify them with the new mesh join command instead where needed. In mac80211, beaconing must now also follow the mesh enabled/not enabled state, which is done by testing the mesh ID. Signed-off-by: Javier Cardona Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- net/wireless/mesh.c | 140 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 140 insertions(+) create mode 100644 net/wireless/mesh.c (limited to 'net/wireless/mesh.c') diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c new file mode 100644 index 000000000000..e0b9747fe50a --- /dev/null +++ b/net/wireless/mesh.c @@ -0,0 +1,140 @@ +#include +#include +#include "core.h" + +/* Default values, timeouts in ms */ +#define MESH_TTL 31 +#define MESH_DEFAULT_ELEMENT_TTL 31 +#define MESH_MAX_RETR 3 +#define MESH_RET_T 100 +#define MESH_CONF_T 100 +#define MESH_HOLD_T 100 + +#define MESH_PATH_TIMEOUT 5000 + +/* + * Minimum interval between two consecutive PREQs originated by the same + * interface + */ +#define MESH_PREQ_MIN_INT 10 +#define MESH_DIAM_TRAVERSAL_TIME 50 + +/* + * A path will be refreshed if it is used PATH_REFRESH_TIME milliseconds + * before timing out. This way it will remain ACTIVE and no data frames + * will be unnecessarily held in the pending queue. + */ +#define MESH_PATH_REFRESH_TIME 1000 +#define MESH_MIN_DISCOVERY_TIMEOUT (2 * MESH_DIAM_TRAVERSAL_TIME) + +/* Default maximum number of established plinks per interface */ +#define MESH_MAX_ESTAB_PLINKS 32 + +#define MESH_MAX_PREQ_RETRIES 4 + + +const struct mesh_config default_mesh_config = { + .dot11MeshRetryTimeout = MESH_RET_T, + .dot11MeshConfirmTimeout = MESH_CONF_T, + .dot11MeshHoldingTimeout = MESH_HOLD_T, + .dot11MeshMaxRetries = MESH_MAX_RETR, + .dot11MeshTTL = MESH_TTL, + .element_ttl = MESH_DEFAULT_ELEMENT_TTL, + .auto_open_plinks = true, + .dot11MeshMaxPeerLinks = MESH_MAX_ESTAB_PLINKS, + .dot11MeshHWMPactivePathTimeout = MESH_PATH_TIMEOUT, + .dot11MeshHWMPpreqMinInterval = MESH_PREQ_MIN_INT, + .dot11MeshHWMPnetDiameterTraversalTime = MESH_DIAM_TRAVERSAL_TIME, + .dot11MeshHWMPmaxPREQretries = MESH_MAX_PREQ_RETRIES, + .path_refresh_time = MESH_PATH_REFRESH_TIME, + .min_discovery_timeout = MESH_MIN_DISCOVERY_TIMEOUT, +}; + + +int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev, + struct net_device *dev, + const u8 *mesh_id, u8 mesh_id_len, + const struct mesh_config *conf) +{ + struct wireless_dev *wdev = dev->ieee80211_ptr; + struct mesh_setup setup = { + .mesh_id = mesh_id, + .mesh_id_len = mesh_id_len, + }; + int err; + + BUILD_BUG_ON(IEEE80211_MAX_SSID_LEN != IEEE80211_MAX_MESH_ID_LEN); + + ASSERT_WDEV_LOCK(wdev); + + if (dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT) + return -EOPNOTSUPP; + + if (wdev->mesh_id_len) + return -EALREADY; + + if (!mesh_id_len) + return -EINVAL; + + if (!rdev->ops->join_mesh) + return -EOPNOTSUPP; + + err = rdev->ops->join_mesh(&rdev->wiphy, dev, conf, &setup); + if (!err) { + memcpy(wdev->ssid, mesh_id, mesh_id_len); + wdev->mesh_id_len = mesh_id_len; + } + + return err; +} + +int cfg80211_join_mesh(struct cfg80211_registered_device *rdev, + struct net_device *dev, + const u8 *mesh_id, u8 mesh_id_len, + const struct mesh_config *conf) +{ + struct wireless_dev *wdev = dev->ieee80211_ptr; + int err; + + wdev_lock(wdev); + err = __cfg80211_join_mesh(rdev, dev, mesh_id, mesh_id_len, conf); + wdev_unlock(wdev); + + return err; +} + +static int __cfg80211_leave_mesh(struct cfg80211_registered_device *rdev, + struct net_device *dev) +{ + struct wireless_dev *wdev = dev->ieee80211_ptr; + int err; + + ASSERT_WDEV_LOCK(wdev); + + if (dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT) + return -EOPNOTSUPP; + + if (!rdev->ops->leave_mesh) + return -EOPNOTSUPP; + + if (!wdev->mesh_id_len) + return -ENOTCONN; + + err = rdev->ops->leave_mesh(&rdev->wiphy, dev); + if (!err) + wdev->mesh_id_len = 0; + return err; +} + +int cfg80211_leave_mesh(struct cfg80211_registered_device *rdev, + struct net_device *dev) +{ + struct wireless_dev *wdev = dev->ieee80211_ptr; + int err; + + wdev_lock(wdev); + err = __cfg80211_leave_mesh(rdev, dev); + wdev_unlock(wdev); + + return err; +} -- cgit v1.2.3 From c80d545da3f7c0e534ccd4a780f322f80a92cff1 Mon Sep 17 00:00:00 2001 From: Javier Cardona Date: Thu, 16 Dec 2010 17:37:49 -0800 Subject: mac80211: Let userspace enable and configure vendor specific path selection. Userspace will now be allowed to toggle between the default path selection algorithm (HWMP, implemented in the kernel), and a vendor specific alternative. Also in the same patch, allow userspace to add information elements to mesh beacons. This is accordance with the Extensible Path Selection Framework specified in version 7.0 of the 802.11s draft. Signed-off-by: Javier Cardona Signed-off-by: John W. Linville --- net/wireless/mesh.c | 24 +++++++++++++----------- 1 file changed, 13 insertions(+), 11 deletions(-) (limited to 'net/wireless/mesh.c') diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c index e0b9747fe50a..73e39c171ffb 100644 --- a/net/wireless/mesh.c +++ b/net/wireless/mesh.c @@ -50,17 +50,19 @@ const struct mesh_config default_mesh_config = { .min_discovery_timeout = MESH_MIN_DISCOVERY_TIMEOUT, }; +const struct mesh_setup default_mesh_setup = { + .path_sel_proto = IEEE80211_PATH_PROTOCOL_HWMP, + .path_metric = IEEE80211_PATH_METRIC_AIRTIME, + .vendor_ie = NULL, + .vendor_ie_len = 0, +}; int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev, struct net_device *dev, - const u8 *mesh_id, u8 mesh_id_len, + const struct mesh_setup *setup, const struct mesh_config *conf) { struct wireless_dev *wdev = dev->ieee80211_ptr; - struct mesh_setup setup = { - .mesh_id = mesh_id, - .mesh_id_len = mesh_id_len, - }; int err; BUILD_BUG_ON(IEEE80211_MAX_SSID_LEN != IEEE80211_MAX_MESH_ID_LEN); @@ -73,16 +75,16 @@ int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev, if (wdev->mesh_id_len) return -EALREADY; - if (!mesh_id_len) + if (!setup->mesh_id_len) return -EINVAL; if (!rdev->ops->join_mesh) return -EOPNOTSUPP; - err = rdev->ops->join_mesh(&rdev->wiphy, dev, conf, &setup); + err = rdev->ops->join_mesh(&rdev->wiphy, dev, conf, setup); if (!err) { - memcpy(wdev->ssid, mesh_id, mesh_id_len); - wdev->mesh_id_len = mesh_id_len; + memcpy(wdev->ssid, setup->mesh_id, setup->mesh_id_len); + wdev->mesh_id_len = setup->mesh_id_len; } return err; @@ -90,14 +92,14 @@ int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev, int cfg80211_join_mesh(struct cfg80211_registered_device *rdev, struct net_device *dev, - const u8 *mesh_id, u8 mesh_id_len, + const struct mesh_setup *setup, const struct mesh_config *conf) { struct wireless_dev *wdev = dev->ieee80211_ptr; int err; wdev_lock(wdev); - err = __cfg80211_join_mesh(rdev, dev, mesh_id, mesh_id_len, conf); + err = __cfg80211_join_mesh(rdev, dev, setup, conf); wdev_unlock(wdev); return err; -- cgit v1.2.3