Linux Ethernet Bonding Driver HOWTO Initial release : Thomas Davis Corrections, HA extensions : 2000/10/03-15 : - Willy Tarreau - Constantine Gavrilov - Chad N. Tindel - Janice Girouard - Jay Vosburgh Reorganized and updated Feb 2005 by Jay Vosburgh Note : ------ The bonding driver originally came from Donald Becker's beowulf patches for kernel 2.0. It has changed quite a bit since, and the original tools from extreme-linux and beowulf sites will not work with this version of the driver. For new versions of the driver, patches for older kernels and the updated userspace tools, please follow the links at the end of this file. Table of Contents ================= 1. Bonding Driver Installation 2. Bonding Driver Options 3. Configuring Bonding Devices 3.1 Configuration with sysconfig support 3.2 Configuration with initscripts support 3.3 Configuring Bonding Manually 3.4 Configuring Multiple Bonds 5. Querying Bonding Configuration 5.1 Bonding Configuration 5.2 Network Configuration 6. Switch Configuration 7. 802.1q VLAN Support 8. Link Monitoring 8.1 ARP Monitor Operation 8.2 Configuring Multiple ARP Targets 8.3 MII Monitor Operation 9. Potential Trouble Sources 9.1 Adventures in Routing 9.2 Ethernet Device Renaming 9.3 Painfully Slow Or No Failed Link Detection By Miimon 10. SNMP agents 11. Promiscuous mode 12. High Availability Information 12.1 High Availability in a Single Switch Topology 12.1.1 Bonding Mode Selection for Single Switch Topology 12.1.2 Link Monitoring for Single Switch Topology 12.2 High Availability in a Multiple Switch Topology 12.2.1 Bonding Mode Selection for Multiple Switch Topology 12.2.2 Link Monitoring for Multiple Switch Topology 12.3 Switch Behavior Issues for High Availability 13. Hardware Specific Considerations 13.1 IBM BladeCenter 14. Frequently Asked Questions 15. Resources and Links 1. Bonding Driver Installation ============================== Most popular distro kernels ship with the bonding driver already available as a module and the ifenslave user level control program installed and ready for use. If your distro does not, or you have need to compile bonding from source (e.g., configuring and installing a mainline kernel from kernel.org), you'll need to perform the following steps: 1.1 Configure and build the kernel with bonding ----------------------------------------------- The latest version of the bonding driver is available in the drivers/net/bonding subdirectory of the most recent kernel source (which is available on http://kernel.org). Prior to the 2.4.11 kernel, the bonding driver was maintained largely outside the kernel tree; patches for some earlier kernels are available on the bonding sourceforge site, although those patches are still several years out of date. Most users will want to use either the most recent kernel from kernel.org or whatever kernel came with their distro. Configure kernel with "make menuconfig" (or "make xconfig" or "make config"), then select "Bonding driver support" in the "Network device support" section. It is recommended that you configure the driver as module since it is currently the only way to pass parameters to the driver or configure more than one bonding device. Build and install the new kernel and modules, then proceed to step 2. 1.2 Install ifenslave Control Utility ------------------------------------- The ifenslave user level control program is included in the kernel source tree, in the file Documentation/networking/ifenslave.c. It is generally recommended that you use the ifenslave that corresponds to the kernel that you are using (either from the same source tree or supplied with the distro), however, ifenslave executables from older kernels should function (but features newer than the ifenslave release are not supported). Running an ifenslave that is newer than the kernel is not supported, and may or may not work. To install ifenslave, do the following: # gcc -Wall -O -I/usr/src/linux/include ifenslave.c -o ifenslave # cp ifenslave /sbin/ifenslave If your kernel source is not in "/usr/src/linux," then replace "/usr/src/linux/include" in the above with the location of your kernel source include directory. You may wish to back up any existing /sbin/ifenslave, or, for testing or informal use, tag the ifenslave to the kernel version (e.g., name the ifenslave executable /sbin/ifenslave-2.6.10). IMPORTANT NOTE: If you omit the "-I" or specify an incorrect directory, you may end up with an ifenslave that is incompatible with the kernel you're trying to build it for. Some distros (e.g., Red Hat from 7.1 onwards) do not have /usr/include/linux symbolically linked to the default kernel source include directory. 2. Bonding Driver Options ========================= Options for the bonding driver are supplied as parameters to the bonding module at load time. They may be given as command line arguments to the insmod or modprobe command, but are usually specified in either the /etc/modprobe.conf configuration file, or in a distro-specific configuration file (some of which are detailed in the next section). The available bonding driver parameters are listed below. If a parameter is not specified the default value is used. When initially configuring a bond, it is recommended "tail -f /var/log/messages" be run in a separate window to watch for bonding driver error messages. It is critical that either the miimon or arp_interval and arp_ip_target parameters be specified, otherwise serious network degradation will occur during link failures. Very few devices do not support at least miimon, so there is really no reason not to use it. Options with textual values will accept either the text name or, for backwards compatibility, the option value. E.g., "mode=802.3ad" and "mode=4" set the same mode. The parameters are as follows: arp_interval Specifies the ARP monitoring frequency in milli-seconds. If ARP monitoring is used in a load-balancing mode (mode 0 or 2), the switch should be configured in a mode that evenly distributes packets across all links - such as round-robin. If the switch is configured to distribute the packets in an XOR fashion, all replies from the ARP targets will be received on the same link which could cause the other team members to fail. ARP monitoring should not be used in conjunction with miimon. A value of 0 disables ARP monitoring. The default value is 0. arp_ip_target Specifies the ip addresses to use when arp_interval is > 0. These are the targets of the ARP request sent to determine the health of the link to the targets. Specify these values in ddd.ddd.ddd.ddd format. Multiple ip adresses must be seperated by a comma. At least one IP address must be given for ARP monitoring to function. The maximum number of targets that can be specified is 16. The default value is no IP addresses. downdelay Specifies the time, in milliseconds, to wait before disabling a slave after a link failure has been detected. This option is only valid for the miimon link monitor. The downdelay value should be a multiple of the miimon value; if not, it will be rounded down to the nearest multiple. The default value is 0. lacp_rate Option specifying the rate in which we'll ask our link partner to transmit LACPDU packets in 802.3ad mode. Possible values are: slow or 0 Request partner to transmit LACPDUs every 30 seconds (default) fast or 1 Request partner to transmit LACPDUs every 1 second max_bonds Specifies the number of bonding devices to create for this instance of the bonding driver. E.g., if max_bonds is 3, and the bonding driver is not already loaded, then bond0, bond1 and bond2 will be created. The default value is 1. miimon Specifies the frequency in milli-seconds that MII link monitoring will occur. A value of zero disables MII link monitoring. A value of 100 is a good starting point. The use_carrier option, below, affects how the link state is determined. See the High Availability section for additional information. The default value is 0. mode Specifies one of the bonding policies. The default is balance-rr (round robin). Possible values are: balance-rr or 0 Round-robin policy: Transmit packets in sequential order from the first available slave through the last. This mode provides load balancing and fault tolerance. active-backup or 1 Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. This mode provides fault tolerance. The primary option affects the behavior of this mode. balance-xor or 2 XOR policy: Transmit based on [(source MAC address XOR'd with destination MAC address) modulo slave count]. This selects the same slave for each destination MAC address. This mode provides load balancing and fault tolerance. broadcast or 3 Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance. 802.3ad or 4 IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification. Pre-requisites: 1. Ethtool support in the base drivers for retrieving the speed and duplex of each slave. 2. A switch that supports IEEE 802.3ad Dynamic link aggregation. Most switches will require some type of configuration to enable 802.3ad mode. balance-tlb or 5 Adaptive transmit load balancing: channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to the speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave. Prerequisite: Ethtool support in the base drivers for retrieving the speed of each slave. balance-alb or 6 Adaptive load balancing: includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server. Receive traffic from connections created by the server is also balanced. When the local system sends an ARP Request the bonding driver copies and saves the peer's IP information from the ARP packet. When the ARP Reply arrives from the peer, its hardware address is retrieved and the bonding driver initiates an ARP reply to this peer assigning it to one of the slaves in the bond. A problematic outcome of using ARP negotiation for balancing is that each time that an ARP request is broadcast it uses the hardware address of the bond. Hence, peers learn the hardware address of the bond and the balancing of receive traffic collapses to the current slave. This is handled by sending updates (ARP Replies) to all the peers with their individually assigned hardware address such that the traffic is redistributed. Receive traffic is also redistributed when a new slave is added to the bond and when an inactive slave is re-activated. The receive load is distributed sequentially (round robin) among the group of highest speed slaves in the bond. When a link is reconnected or a new slave joins the bond the receive traffic is redistributed among all active slaves in the bond by intiating ARP Replies with the selected mac address to each of the clients. The updelay parameter (detailed below) must be set to a value equal or greater than the switch's forwarding delay so that the ARP Replies sent to the peers will not be blocked by the switch. Prerequisites: 1. Ethtool support in the base drivers for retrieving the speed of each slave. 2. Base driver support for setting the hardware address of a device while it is open. This is required so that there will always be one slave in the team using the bond hardware address (the curr_active_slave) while having a unique hardware address for each slave in the bond. If the curr_active_slave fails its hardware address is swapped with the new curr_active_slave that was chosen. primary A string (eth0, eth2, etc) specifying which slave is the primary device. The specified device will always be the active slave while it is available. Only when the primary is off-line will alternate devices be used. This is useful when one slave is preferred over another, e.g., when one slave has higher throughput than another. The primary option is only valid for active-backup mode. updelay Specifies the time, in milliseconds, to wait before enabling a slave after a link recovery has been detected. This option is only valid for the miimon link monitor. The updelay value should be a multiple of the miimon value; if not, it will be rounded down to the nearest multiple. The default value is 0. use_carrier Specifies whether or not miimon should use MII or ETHTOOL ioctls vs. netif_carrier_ok() to determine the link status. The MII or ETHTOOL ioctls are less efficient and utilize a deprecated calling sequence within the kernel. The netif_carrier_ok() relies on the device driver to maintain its state with netif_carrier_on/off; at this writing, most, but not all, device drivers support this facility. If bonding insists that the link is up when it should not be, it may be that your network device driver does not support netif_carrier_on/off. The default state for netif_carrier is "carrier on," so if a driver does not support netif_carrier, it will appear as if the link is always up. In this case, setting use_carrier to 0 will cause bonding to revert to the MII / ETHTOOL ioctl method to determine the link state. A value of 1 enables the use of netif_carrier_ok(), a value of 0 will use the deprecated MII / ETHTOOL ioctls. The default value is 1. 3. Configuring Bonding Devices ============================== There are, essentially, two methods for configuring bonding: with support from the distro's network initialization scripts, and without. Distros generally use one of two packages for the network initialization scripts: initscripts or sysconfig. Recent versions of these packages have support for bonding, while older versions do not. We will first describe the options for configuring bonding for distros using versions of initscripts and sysconfig with full or partial support for bonding, then provide information on enabling bonding without support from the network initialization scripts (i.e., older versions of initscripts or sysconfig). If you're unsure whether your distro uses sysconfig or initscripts, or don't know if it's new enough, have no fear. Determining this is fairly straightforward. First, issue the command: $ rpm -qf /sbin/ifup It will respond with a line of text starting with either "initscripts" or "sysconfig," followed by some numbers. This is the package that provides your network initialization scripts. Next, to determine if your installation supports bonding, issue the command: $ grep ifenslave /sbin/ifup If this returns any matches, then your initscripts or sysconfig has support for bonding. 3.1 Configuration with sysconfig support ---------------------------------------- This section applies to distros using a version of sysconfig with bonding support, for example, SuSE Linux Enterprise Server 9. SuSE SLES 9's networking configuration system does support bonding, however, at this writing, the YaST system configuration frontend does not provide any means to work with bonding devices. Bonding devices can be managed by hand, however, as follows. First, if they have not already been configured, configure the slave devices. On SLES 9, this is most easily done by running the yast2 sysconfig configuration utility. The goal is for to create an ifcfg-id file for each slave device. The simplest way to accomplish this is to configure the devices for DHCP. The name of the configuration file for each device will be of the form: ifcfg-id-xx:xx:xx:xx:xx:xx Where the "xx" portion will be replaced with the digits from the device's permanent MAC address. Once the set of ifcfg-id-xx:xx:xx:xx:xx:xx files has been created, it is necessary to edit the configuration files for the slave devices (the MAC addresses correspond to those of the slave devices). Before editing, the file will contain muliple lines, and will look something like this: BOOTPROTO='dhcp' STARTMODE='on' USERCTL='no' UNIQUE='XNzu.WeZGOGF+4wE' _nm_name='bus-pci-0001:61:01.0' Change the BOOTPROTO and STARTMODE lines to the following: BOOTPROTO='none' STARTMODE='off' Do not alter the UNIQUE or _nm_name lines. Remove any other lines (USERCTL, etc). Once the ifcfg-id-xx:xx:xx:xx:xx:xx files have been modified, it's time to create the configuration file for the bonding device itself. This file is named ifcfg-bondX, where X is the number of the bonding device to create, starting at 0. The first such file is ifcfg-bond0, the second is ifcfg-bond1, and so on. The sysconfig network configuration system will correctly start multiple instances of bonding. The contents of the ifcfg-bondX file is as follows: BOOTPROTO="static" BROADCAST="10.0.2.255" IPADDR="10.0.2.10" NETMASK="255.255.0.0" NETWORK="10.0.2.0" REMOTE_IPADDR="" STARTMODE="onboot" BONDING_MASTER="yes" BONDING_MODULE_OPTS="mode=active-backup miimon=100" BONDING_SLAVE0="eth0" BONDING_SLAVE1="eth1" Replace the sample BROADCAST, IPADDR, NETMASK and NETWORK values with the appropriate values for your network. Note that configuring the bonding device with BOOTPROTO='dhcp' does not work; the scripts attempt to obtain the device address from DHCP prior to adding any of the slave devices. Without active slaves, the DHCP requests are not sent to the network. The STARTMODE specifies when the device is brought online. The possible values are: onboot: The device is started at boot time. If you're not sure, this is probably what you want. manual: The device is started only when ifup is called manually. Bonding devices may be configured this way if you do not wish them to start automatically at boot for some reason. hotplug: The device is started by a hotplug event. This is not a valid choice for a bonding device. off or ignore: The device configuration is ignored. The line BONDING_MASTER='yes' indicates that the device is a bonding master device. The only useful value is "yes." The contents of BONDING_MODULE_OPTS are supplied to the instance of the bonding module for this device. Specify the options for the bonding mode, link monitoring, and so on here. Do not include the max_bonds bonding parameter; this will confuse the configuration system if you have multiple bonding devices. Finally, supply one BONDING_SLAVEn="ethX" for each slave, where "n" is an increasing value, one for each slave, and "ethX" is the name of the slave device (eth0, eth1, etc). When all configuration files have been modified or created, networking must be restarted for the configuration changes to take effect. This can be accomplished via the following: # /etc/init.d/network restart Note that the network control script (/sbin/ifdown) will remove the bonding module as part of the network shutdown processing, so it is not necessary to remove the module by hand if, e.g., the module paramters have changed. Also, at this writing, YaST/YaST2 will not manage bonding devices (they do not show bonding interfaces on its list of network devices). It is necessary to edit the configuration file by hand to change the bonding configuration. Additional general options and details of the ifcfg file format can be found in an example ifcfg template file: /etc/sysconfig/network/ifcfg.template Note that the template does not document the various BONDING_ settings described above, but does describe many of the other options. 3.2 Configuration with initscripts support ------------------------------------------ This section applies to distros using a version of initscripts with bonding support, for example, Red Hat Linux 9 or Red Hat Enterprise Linux version 3. On these systems, the network initialization scripts have some knowledge of bonding, and can be configured to control bonding devices. These distros will not automatically load the network adapter driver unless the ethX device is configured with an IP address. Because of this constraint, users must manually configure a network-script file for all physical adapters that will be members of a bondX link. Network script files are located in the directory: /etc/sysconfig/network-scripts The file name must be prefixed with "ifcfg-eth" and suffixed with the adapter's physical adapter number. For example, the script for eth0 would be named /etc/sysconfig/network-scripts/ifcfg-eth0. Place the following text in the file: DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none The DEVICE= line will be different for every ethX device and must correspond with the name of the file, i.e., ifcfg-eth1 must have a device line of DEVICE=eth1. The setting of the MASTER= line will also depend on the final bonding interface name chosen for your bond. As with other network devices, these typically start at 0, and go up one for each device, i.e., the first bonding instance is bond0, the second is bond1, and so on. Next, create a bond network script. The file name for this script will be /etc/sysconfig/network-scripts/ifcfg-bondX where X is the number of the bond. For bond0 the file is named "ifcfg-bond0", for bond1 it is named "ifcfg-bond1", and so on. Within that file, place the following text: DEVICE=bond0 IPADDR=192.168.1.1 NETMASK=255.255.255.0 NETWORK=192.168.1.0 BROADCAST=192.168.1.255 ONBOOT=yes BOOTPROTO=none USERCTL=no Be sure to change the networking specific lines (IPADDR, NETMASK, NETWORK and BROADCAST) to match your network configuration. Finally, it is necessary to edit /etc/modules.conf to load the bonding module when the bond0 interface is brought up. The following sample lines in /etc/modules.conf will load the bonding module, and select its options: alias bond0 bonding options bond0 mode=balance-alb miimon=100 Replace the sample parameters with the appropriate set of options for your configuration. Finally run "/etc/rc.d/init.d/network restart" as root. This will restart the networking subsystem and your bond link should be now up and running. 3.3 Configuring Bonding Manually -------------------------------- This section applies to distros whose network initialization scripts (the sysconfig or initscripts package) do not have specific knowledge of bonding. One such distro is SuSE Linux Enterprise Server version 8. The general methodology for these systems is to place the bonding module parameters into /etc/modprobe.conf, then add modprobe and/or ifenslave commands to the system's global init script. The name of the global init script differs; for sysconfig, it is /etc/init.d/boot.local and for initscripts it is /etc/rc.d/rc.local. For example, if you wanted to make a simple bond of two e100 devices (presumed to be eth0 and eth1), and have it persist across reboots, edit the appropriate file (/etc/init.d/boot.local or /etc/rc.d/rc.local), and add the following: modprobe bonding -obond0 mode=balance-alb miimon=100 modprobe e100 ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up ifenslave bond0 eth0 ifenslave bond0 eth1 Replace the example bonding module parameters and bond0 network configuration (IP address, netmask, etc) with the appropriate values for your configuration. The above example loads the bonding module with the name "bond0," this simplifies the naming if multiple bonding modules are loaded (each successive instance of the module is given a different name, and the module instance names match the bonding interface names). Unfortunately, this method will not provide support for the ifup and ifdown scripts on the bond devices. To reload the bonding configuration, it is necessary to run the initialization script, e.g., # /etc/init.d/boot.local or # /etc/rc.d/rc.local It may be desirable in such a case to create a separate script which only initializes the bonding configuration, then call that separate script from within boot.local. This allows for bonding to be enabled without re-running the entire global init script. To shut down the bonding devices, it is necessary to first mark the bonding device itself as being down, then remove the appropriate device driver modules. For our example above, you can do the following: # ifconfig bond0 down # rmmod bond0 # rmmod e100 Again, for convenience, it may be desirable to create a script with these commands. 3.4 Configuring Multiple Bonds ------------------------------ This section contains information on configuring multiple bonding devices with differing options. If you require multiple bonding devices, but all with the same options, see the "max_bonds" module paramter, documented above. To create multiple bonding devices with differing options, it is necessary to load the bonding driver multiple times. Note that current versions of the sysconfig network initialization scripts handle this automatically; if your distro uses these scripts, no special action is needed. See the section Configuring Bonding Devices, above, if you're not sure about your network initialization scripts. To load multiple instances of the module, it is necessary to specify a different name for each instance (the module loading system requires that every loaded module, even multiple instances of the same module, have a unique name). This is accomplished by supplying multiple sets of bonding options in /etc/modprobe.conf, for example: alias bond0 bonding options bond0 -o bond0 mode=balance-rr miimon=100 alias bond1 bonding options bond1 -o bond1 mode=balance-alb miimon=50 will load the bonding module two times. The first instance is named "bond0" and creates the bond0 device in balance-rr mode with an miimon of 100. The second instance is named "bond1" and creates the bond1 device in balance-alb mode with an miimon of 50. This may be repeated any number of times, specifying a new and unique name in place of bond0 or bond1 for each instance. When the appropriate module paramters are in place, then configure bonding according to the instructions for your distro. 5. Querying Bonding Configuration ================================= 5.1 Bonding Configuration ------------------------- Each bonding device has a read-only file residing in the /proc/net/bonding directory. The file contents include information about the bonding configuration, options and state of each slave. For example, the contents of /proc/net/bonding/bond0 after the driver is loaded with parameters of mode=0 and miimon=1000 is generally as follows: Ethernet Channel Bonding Driver: 2.6.1 (October 29, 2004) Bonding Mode: load balancing (round-robin) Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 1000 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth1 MII Status: up Link Failure Count: 1 Slave Interface: eth0 MII Status: up Link Failure Count: 1 The precise format and contents will change depending upon the bonding configuration, state, and version of the bonding driver. 5.2 Network configuration ------------------------- The network configuration can be inspected using the ifconfig command. Bonding devices will have the MASTER flag set; Bonding slave devices will have the SLAVE flag set. The ifconfig output does not contain information on which slaves are associated with which masters. In the example below, the bond0 interface is the master (MASTER) while eth0 and eth1 are slaves (SLAVE). Notice all slaves of bond0 have the same MAC address (HWaddr) as bond0 for all modes except TLB and ALB that require a unique MAC address for each slave. # /sbin/ifconfig bond0 Link encap:Ethernet HWaddr 00:C0:F0:1F:37:B4 inet addr:XXX.XXX.XXX.YYY Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0 UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:7224794 errors:0 dropped:0 overruns:0 frame:0 TX packets:3286647 errors:1 dropped:0 overruns:1 carrier:0 collisions:0 txqueuelen:0 eth0 Link encap:Ethernet HWaddr 00:C0:F0:1F:37:B4 inet addr:XXX.XXX.XXX.YYY Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:3573025 errors:0 dropped:0 overruns:0 frame:0 TX packets:1643167 errors:1 dropped:0 overruns:1 carrier:0 collisions:0 txqueuelen:100 Interrupt:10 Base address:0x1080 eth1 Link encap:Ethernet HWaddr 00:C0:F0:1F:37:B4 inet addr:XXX.XXX.XXX.YYY Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:3651769 errors:0 dropped:0 overruns:0 frame:0 TX packets:1643480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:9 Base address:0x1400 6. Switch Configuration ======================= For this section, "switch" refers to whatever system the bonded devices are directly connected to (i.e., where the other end of the cable plugs into). This may be an actual dedicated switch device, or it may be another regular system (e.g., another computer running Linux), The active-backup, balance-tlb and balance-alb modes do not require any specific configuration of the switch. The 802.3ad mode requires that the switch have the appropriate ports configured as an 802.3ad aggregation. The precise method used to configure this varies from switch to switch, but, for example, a Cisco 3550 series switch requires that the appropriate ports first be grouped together in a single etherchannel instance, then that etherchannel is set to mode "lacp" to enable 802.3ad (instead of standard EtherChannel). The balance-rr, balance-xor and broadcast modes generally require that the switch have the appropriate ports grouped together. The nomenclature for such a group differs between switches, it may be called an "etherchannel" (as in the Cisco example, above), a "trunk group" or some other similar variation. For these modes, each switch will also have its own configuration options for the switch's transmit policy to the bond. Typical choices include XOR of either the MAC or IP addresses. The transmit policy of the two peers does not need to match. For these three modes, the bonding mode really selects a transmit policy for an EtherChannel group; all three will interoperate with another EtherChannel group. 7. 802.1q VLAN Support ====================== It is possible to configure VLAN devices over a bond interface using the 8021q driver. However, only packets coming from the 8021q driver and passing through bonding will be tagged by default. Self generated packets, for example, bonding's learning packets or ARP packets generated by either ALB mode or the ARP monitor mechanism, are tagged internally by bonding itself. As a result, bonding must "learn" the VLAN IDs configured above it, and use those IDs to tag self generated packets. For reasons of simplicity, and to support the use of adapters that can do VLAN hardware acceleration offloding, the bonding interface declares itself as fully hardware offloaing capable, it gets the add_vid/kill_vid notifications to gather the necessary information, and it propagates those actions to the slaves. In case of mixed adapter types, hardware accelerated tagged packets that should go through an adapter that is not offloading capable are "un-accelerated" by the bonding driver so the VLAN tag sits in the regular location. VLAN interfaces *must* be added on top of a bonding interface only after enslaving at least one slave. The bonding interface has a hardware address of 00:00:00:00:00:00 until the first slave is added. If the VLAN interface is created prior to the first enslavement, it would pick up the all-zeroes hardware address. Once the first slave is attached to the bond, the bond device itself will pick up the slave's hardware address, which is then available for the VLAN device. Also, be aware that a similar problem can occur if all slaves are released from a bond that still has one or more VLAN interfaces on top of it. When a new slave is added, the bonding interface will obtain its hardware address from the first slave, which might not match the hardware address of the VLAN interfaces (which was ultimately copied from an earlier slave). There are two methods to insure that the VLAN device operates with the correct hardware address if all slaves are removed from a bond interface: 1. Remove all VLAN interfaces then recreate them 2. Set the bonding interface's hardware address so that it matches the hardware address of the VLAN interfaces. Note that changing a VLAN interface's HW address would set the underlying device -- i.e. the bonding interface -- to promiscouos mode, which might not be what you want. 8. Link Monitoring ================== The bonding driver at present supports two schemes for monitoring a slave device's link state: the ARP monitor and the MII monitor. At the present time, due to implementation restrictions in the bonding driver itself, it is not possible to enable both ARP and MII monitoring simultaneously. 8.1 ARP Monitor Operation ------------------------- The ARP monitor operates as its name suggests: it sends ARP queries to one or more designated peer systems on the network, and uses the response as an indication that the link is operating. This gives some assurance that traffic is actually flowing to and from one or more peers on the local network. The ARP monitor relies on the device driver itself to verify that traffic is flowing. In particular, the driver must keep up to date the last receive time, dev->last_rx, and transmit start time, dev->trans_start. If these are not updated by the driver, then the ARP monitor will immediately fail any slaves using that driver, and those slaves will stay down. If networking monitoring (tcpdump, etc) shows the ARP requests and replies on the network, then it may be that your device driver is not updating last_rx and trans_start. 8.2 Configuring Multiple ARP Targets ------------------------------------ While ARP monitoring can be done with just one target, it can be useful in a High Availability setup to have several targets to monitor. In the case of just one target, the target itself may go down or have a problem making it unresponsive to ARP requests. Having an additional target (or several) increases the reliability of the ARP monitoring. Multiple ARP targets must be seperated by commas as follows: # example options for ARP monitoring with three targets alias bond0 bonding options bond0 arp_interval=60 arp_ip_target=192.168.0.1,192.168.0.3,192.168.0.9 For just a single target the options would resemble: # example options for ARP monitoring with one target alias bond0 bonding options bond0 arp_interval=60 arp_ip_target=192.168.0.100 8.3 MII Monitor Operation ------------------------- The MII monitor monitors only the carrier state of the local network interface. It accomplishes this in one of three ways: by depending upon the device driver to maintain its carrier state, by querying the device's MII registers, or by making an ethtool query to the device. If the use_carrier module parameter is 1 (the default value), then the MII monitor will rely on the driver for carrier state information (via the netif_carrier subsystem). As explained in the use_carrier parameter information, above, if the MII monitor fails to detect carrier loss on the device (e.g., when the cable is physically disconnected), it may be that the driver does not support netif_carrier. If use_carrier is 0, then the MII monitor will first query the device's (via ioctl) MII registers and check the link state. If that request fails (not just that it returns carrier down), then the MII monitor will make an ethtool ETHOOL_GLINK request to attempt to obtain the same information. If both methods fail (i.e., the driver either does not support or had some error in processing both the MII register and ethtool requests), then the MII monitor will assume the link is up. 9. Potential Sources of Trouble =============================== 9.1 Adventures in Routing ------------------------- When bonding is configured, it is important that the slave devices not have routes that supercede routes of the master (or, generally, not have routes at all). For example, suppose the bonding device bond0 has two slaves, eth0 and eth1, and the routing table is as follows: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.0.0 U 40 0 0 eth0 10.0.0.0 0.0.0.0 255.255.0.0 U 40 0 0 eth1 10.0.0.0 0.0.0.0 255.255.0.0 U 40 0 0 bond0 127.0.0.0 0.0.0.0 255.0.0.0 U 40 0 0 lo This routing configuration will likely still update the receive/transmit times in the driver (needed by the ARP monitor), but may bypass the bonding driver (because outgoing traffic to, in this case, another host on network 10 would use eth0 or eth1 before bond0). The ARP monitor (and ARP itself) may become confused by this configuration, because ARP requests (generated by the ARP monitor) will be sent on one interface (bond0), but the corresponding reply will arrive on a different interface (eth0). This reply looks to ARP as an unsolicited ARP reply (because ARP matches replies on an interface basis), and is discarded. The MII monitor is not affected by the state of the routing table. The solution here is simply to insure that slaves do not have routes of their own, and if for some reason they must, those routes do not supercede routes of their master. This should generally be the case, but unusual configurations or errant manual or automatic static route additions may cause trouble. 9.2 Ethernet Device Renaming ---------------------------- On systems with network configuration scripts that do not associate physical devices directly with network interface names (so that the same physical device always has the same "ethX" name), it may be necessary to add some special logic to either /etc/modules.conf or /etc/modprobe.conf (depending upon which is installed on the system). For example, given a modules.conf containing the following: alias bond0 bonding options bond0 mode=some-mode miimon=50 alias eth0 tg3 alias eth1 tg3 alias eth2 e1000 alias eth3 e1000 If neither eth0 and eth1 are slaves to bond0, then when the bond0 interface comes up, the devices may end up reordered. This happens because bonding is loaded first, then its slave device's drivers are loaded next. Since no other drivers have been loaded, when the e1000 driver loads, it will receive eth0 and eth1 for its devices, but the bonding configuration tries to enslave eth2 and eth3 (which may later be assigned to the tg3 devices). Adding the following: add above bonding e1000 tg3 causes modprobe to load e1000 then tg3, in that order, when bonding is loaded. This command is fully documented in the modules.conf manual page. On systems utilizing modprobe.conf (or modprobe.conf.local), an equivalent problem can occur. In this case, the following can be added to modprobe.conf (or modprobe.conf.local, as appropriate), as follows (all on one line; it has been split here for clarity): install bonding /sbin/modprobe tg3; /sbin/modprobe e1000; /sbin/modprobe --ignore-install bonding This will, when loading the bonding module, rather than performing the normal action, instead execute the provided command. This command loads the device drivers in the order needed, then calls modprobe with --ingore-install to cause the normal action to then take place. Full documentation on this can be found in the modprobe.conf and modprobe manual pages. 9.3. Painfully Slow Or No Failed Link Detection By Miimon --------------------------------------------------------- By default, bonding enables the use_carrier option, which instructs bonding to trust the driver to maintain carrier state. As discussed in the options section, above, some drivers do not support the netif_carrier_on/_off link state tracking system. With use_carrier enabled, bonding will always see these links as up, regardless of their actual state. Additionally, other drivers do support netif_carrier, but do not maintain it in real time, e.g., only polling the link state at some fixed interval. In this case, miimon will detect failures, but only after some long period of time has expired. If it appears that miimon is very slow in detecting link failures, try specifying use_carrier=0 to see if that improves the failure detection time. If it does, then it may be that the driver checks the carrier state at a fixed interval, but does not cache the MII register values (so the use_carrier=0 method of querying the registers directly works). If use_carrier=0 does not improve the failover, then the driver may cache the registers, or the problem may be elsewhere. Also, remember that miimon only checks for the device's carrier state. It has no way to determine the state of devices on or beyond other ports of a switch, or if a switch is refusing to pass traffic while still maintaining carrier on. 10. SNMP agents =============== If running SNMP agents, the bonding driver should be loaded before any network drivers participating in a bond. This requirement is due to the the interface index (ipAdEntIfIndex) being associated to the first interface found with a given IP address. That is, there is only one ipAdEntIfIndex for each IP address. For example, if eth0 and eth1 are slaves of bond0 and the driver for eth0 is loaded before the bonding driver, the interface for the IP address will be associated with the eth0 interface. This configuration is shown below, the IP address 192.168.1.1 has an interface index of 2 which indexes to eth0 in the ifDescr table (ifDescr.2). interfaces.ifTable.ifEntry.ifDescr.1 = lo interfaces.ifTable.ifEntry.ifDescr.2 = eth0 interfaces.ifTable.ifEntry.ifDescr.3 = eth1 interfaces.ifTable.ifEntry.ifDescr.4 = eth2 interfaces.ifTable.ifEntry.ifDescr.5 = eth3 interfaces.ifTable.ifEntry.ifDescr.6 = bond0 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.10.10.10 = 5 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.192.168.1.1 = 2 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.74.20.94 = 4 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.127.0.0.1 = 1 This problem is avoided by loading the bonding driver before any network drivers participating in a bond. Below is an example of loading the bonding driver first, the IP address 192.168.1.1 is correctly associated with ifDescr.2. interfaces.ifTable.ifEntry.ifDescr.1 = lo interfaces.ifTable.ifEntry.ifDescr.2 = bond0 interfaces.ifTable.ifEntry.ifDescr.3 = eth0 interfaces.ifTable.ifEntry.ifDescr.4 = eth1 interfaces.ifTable.ifEntry.ifDescr.5 = eth2 interfaces.ifTable.ifEntry.ifDescr.6 = eth3 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.10.10.10 = 6 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.192.168.1.1 = 2 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.10.74.20.94 = 5 ip.ipAddrTable.ipAddrEntry.ipAdEntIfIndex.127.0.0.1 = 1 While some distributions may not report the interface name in ifDescr, the association between the IP address and IfIndex remains and SNMP functions such as Interface_Scan_Next will report that association. 11. Promiscuous mode ==================== When running network monitoring tools, e.g., tcpdump, it is common to enable promiscuous mode on the device, so that all traffic is seen (instead of seeing only traffic destined for the local host). The bonding driver handles promiscuous mode changes to the bonding master device (e.g., bond0), and propogates the setting to the slave devices. For the balance-rr, balance-xor, broadcast, and 802.3ad modes, the promiscuous mode setting is propogated to all slaves. For the active-backup, balance-tlb and balance-alb modes, the promiscuous mode setting is propogated only to the active slave. For balance-tlb mode, the active slave is the slave currently receiving inbound traffic. For balance-alb mode, the active slave is the slave used as a "primary." This slave is used for mode-specific control traffic, for sending to peers that are unassigned or if the load is unbalanced. For the active-backup, balance-tlb and balance-alb modes, when the active slave changes (e.g., due to a link failure), the promiscuous setting will be propogated to the new active slave. 12. High Availability Information ================================= High Availability refers to configurations that provide maximum network availability by having redundant or backup devices, links and switches between the host and the rest of the world. There are currently two basic methods for configuring to maximize availability. They are dependent on the network topology and the primary goal of the configuration, but in general, a configuration can be optimized for maximum available bandwidth, or for maximum network availability. 12.1 High Availability in a Single Switch Topology -------------------------------------------------- If two hosts (or a host and a switch) are directly connected via multiple physical links, then there is no network availability penalty for optimizing for maximum bandwidth: there is only one switch (or peer), so if it fails, you have no alternative access to fail over to. Example 1 : host to switch (or other host) +----------+ +----------+ | |eth0 eth0| switch | | Host A +--------------------------+ or | | +--------------------------+ other | | |eth1 eth1| host | +----------+ +----------+ 12.1.1 Bonding Mode Selection for single switch topology -------------------------------------------------------- This configuration is the easiest to set up and to understand, although you will have to decide which bonding mode best suits your needs. The tradeoffs for each mode are detailed below: balance-rr: This mode is the only mode that will permit a single TCP/IP connection to stripe traffic across multiple interfaces. It is therefore the only mode that will allow a single TCP/IP stream to utilize more than one interface's worth of throughput. This comes at a cost, however: the striping often results in peer systems receiving packets out of order, causing TCP/IP's congestion control system to kick in, often by retransmitting segments. It is possible to adjust TCP/IP's congestion limits by altering the net.ipv4.tcp_reordering sysctl parameter. The usual default value is 3, and the maximum useful value is 127. For a four interface balance-rr bond, expect that a single TCP/IP stream will utilize no more than approximately 2.3 interface's worth of throughput, even after adjusting tcp_reordering. If you are utilizing protocols other than TCP/IP, UDP for example, and your application can tolerate out of order delivery, then this mode can allow for single stream datagram performance that scales near linearly as interfaces are added to the bond. This mode requires the switch to have the appropriate ports configured for "etherchannel" or "trunking." active-backup: There is not much advantage in this network topology to the active-backup mode, as the inactive backup devices are all connected to the same peer as the primary. In this case, a load balancing mode (with link monitoring) will provide the same level of network availability, but with increased available bandwidth. On the plus side, it does not require any configuration of the switch. balance-xor: This mode will limit traffic such that packets destined for specific peers will always be sent over the same interface. Since the destination is determined by the MAC addresses involved, this may be desirable if you have a large network with many hosts. It is likely to be suboptimal if all your traffic is passed through a single router, however. As with balance-rr, the switch ports need to be configured for "etherchannel" or "trunking." broadcast: Like active-backup, there is not much advantage to this mode in this type of network topology. 802.3ad: This mode can be a good choice for this type of network topology. The 802.3ad mode is an IEEE standard, so all peers that implement 802.3ad should interoperate well. The 802.3ad protocol includes automatic configuration of the aggregates, so minimal manual configuration of the switch is needed (typically only to designate that some set of devices is usable for 802.3ad). The 802.3ad standard also mandates that frames be delivered in order (within certain limits), so in general single connections will not see misordering of packets. The 802.3ad mode does have some drawbacks: the standard mandates that all devices in the aggregate operate at the same speed and duplex. Also, as with all bonding load balance modes other than balance-rr, no single connection will be able to utilize more than a single interface's worth of bandwidth. Additionally, the linux bonding 802.3ad implementation distributes traffic by peer (using an XOR of MAC addresses), so in general all traffic to a particular destination will use the same interface. Finally, the 802.3ad mode mandates the use of the MII monitor, therefore, the ARP monitor is not available in this mode. balance-tlb: This mode is also a good choice for this type of topology. It has no special switch configuration requirements, and balances outgoing traffic by peer, in a vaguely intelligent manner (not a simple XOR as in balance-xor or 802.3ad mode), so that unlucky MAC addresses will not all "bunch up" on a single interface. Interfaces may be of differing speeds. On the down side, in this mode all incoming traffic arrives over a single interface, this mode requires certain ethtool support in the network device driver of the slave interfaces, and the ARP monitor is not available. balance-alb: This mode is everything that balance-tlb is, and more. It has all of the features (and restrictions) of balance-tlb, and will also balance incoming traffic from peers (as described in the Bonding Module Options section, above). The only extra down side to this mode is that the network device driver must support changing the hardware address while the device is open. 12.1.2 Link Monitoring for Single Switch Topology ------------------------------------------------- The choice of link monitoring may largely depend upon which mode you choose to use. The more advanced load balancing modes do not support the use of the ARP monitor, and are thus restricted to using the MII monitor (which does not provide as high a level of assurance as the ARP monitor). 12.2 High Availability in a Multiple Switch Topology ---------------------------------------------------- With multiple switches, the configuration of bonding and the network changes dramatically. In multiple switch topologies, there is a tradeoff between network availability and usable bandwidth. Below is a sample network, configured to maximize the availability of the network: | | |port3 port3| +-----+----+ +-----+----+ | |port2 ISL port2| | | switch A +--------------------------+ switch B | | | | | +-----+----+ +-----++---+ |port1 port1| | +-------+ | +-------------+ host1 +---------------+ eth0 +-------+ eth1 In this configuration, there is a link between the two switches (ISL, or inter switch link), and multiple ports connecting to the outside world ("port3" on each switch). There is no technical reason that this could not be extended to a third switch. 12.2.1 Bonding Mode Selection for Multiple Switch Topology ---------------------------------------------------------- In a topology such as this, the active-backup and broadcast modes are the only useful bonding modes; the other modes require all links to terminate on the same peer for them to behave rationally. active-backup: This is generally the preferred mode, particularly if the switches have an ISL and play together well. If the network configuration is such that one switch is specifically a backup switch (e.g., has lower capacity, higher cost, etc), then the primary option can be used to insure that the preferred link is always used when it is available. broadcast: This mode is really a special purpose mode, and is suitable only for very specific needs. For example, if the two switches are not connected (no ISL), and the networks beyond them are totally independant. In this case, if it is necessary for some specific one-way traffic to reach both independent networks, then the broadcast mode may be suitable. 12.2.2 Link Monitoring Selection for Multiple Switch Topology ------------------------------------------------------------- The choice of link monitoring ultimately depends upon your switch. If the switch can reliably fail ports in response to other failures, then either the MII or ARP monitors should work. For example, in the above example, if the "port3" link fails at the remote end, the MII monitor has no direct means to detect this. The ARP monitor could be configured with a target at the remote end of port3, thus detecting that failure without switch support. In general, however, in a multiple switch topology, the ARP monitor can provide a higher level of reliability in detecting link failures. Additionally, it should be configured with multiple targets (at least one for each switch in the network). This will insure that, regardless of which switch is active, the ARP monitor has a suitable target to query. 12.3 Switch Behavior Issues for High Availability ------------------------------------------------- You may encounter issues with the timing of link up and down reporting by the switch. First, when a link comes up, some switches may indicate that the link is up (carrier available), but not pass traffic over the interface for some period of time. This delay is typically due to some type of autonegotiation or routing protocol, but may also occur during switch initialization (e.g., during recovery after a switch failure). If you find this to be a problem, specify an appropriate value to the updelay bonding module option to delay the use of the relevant interface(s). Second, some switches may "bounce" the link state one or more times while a link is changing state. This occurs most commonly while the switch is initializing. Again, an appropriate updelay value may help, but note that if all links are down, then updelay is ignored when any link becomes active (the slave closest to completing its updelay is chosen). Note that when a bonding interface has no active links, the driver will immediately reuse the first link that goes up, even if updelay parameter was specified. If there are slave interfaces waiting for the updelay timeout to expire, the interface that first went into that state will be immediately reused. This reduces down time of the network if the value of updelay has been overestimated. In addition to the concerns about switch timings, if your switches take a long time to go into backup mode, it may be desirable to not activate a backup interface immediately after a link goes down. Failover may be delayed via the downdelay bonding module option. 13. Hardware Specific Considerations ==================================== This section contains additional information for configuring bonding on specific hardware platforms, or for interfacing bonding with particular switches or other devices. 13.1 IBM BladeCenter -------------------- This applies to the JS20 and similar systems. On the JS20 blades, the bonding driver supports only balance-rr, active-backup, balance-tlb and balance-alb modes. This is largely due to the network topology inside the BladeCenter, detailed below. JS20 network adapter information -------------------------------- All JS20s come with two Broadcom Gigabit Ethernet ports integrated on the planar. In the BladeCenter chassis, the eth0 port of all JS20 blades is hard wired to I/O Module #1; similarly, all eth1 ports are wired to I/O Module #2. An add-on Broadcom daughter card can be installed on a JS20 to provide two more Gigabit Ethernet ports. These ports, eth2 and eth3, are wired to I/O Modules 3 and 4, respectively. Each I/O Module may contain either a switch or a passthrough module (which allows ports to be directly connected to an external switch). Some bonding modes require a specific BladeCenter internal network topology in order to function; these are detailed below. Additional BladeCenter-specific networking information can be found in two IBM Redbooks (www.ibm.com/redbooks): "IBM eServer BladeCenter Networking Options" "IBM eServer BladeCenter Layer 2-7 Network Switching" BladeCenter networking configuration ------------------------------------ Because a BladeCenter can be configured in a very large number of ways, this discussion will be confined to describing basic configurations. Normally, Ethernet Switch Modules (ESM) are used in I/O modules 1 and 2. In this configuration, the eth0 and eth1 ports of a JS20 will be connected to different internal switches (in the respective I/O modules). An optical passthru module (OPM) connects the I/O module directly to an external switch. By using OPMs in I/O module #1 and #2, the eth0 and eth1 interfaces of a JS20 can be redirected to the outside world and connected to a common external switch. Depending upon the mix of ESM and OPM modules, the network will appear to bonding as either a single switch topology (all OPM modules) or as a multiple switch topology (one or more ESM modules, zero or more OPM modules). It is also possible to connect ESM modules together, resulting in a configuration much like the example in "High Availability in a multiple switch topology." Requirements for specifc modes ------------------------------ The balance-rr mode requires the use of OPM modules for devices in the bond, all connected to an common external switch. That switch must be configured for "etherchannel" or "trunking" on the appropriate ports, as is usual for balance-rr. The balance-alb and balance-tlb modes will function with either switch modules or passthrough modules (or a mix). The only specific requirement for these modes is that all network interfaces must be able to reach all destinations for traffic sent over the bonding device (i.e., the network must converge at some point outside the BladeCenter). The active-backup mode has no additional requirements. Link monitoring issues ---------------------- When an Ethernet Switch Module is in place, only the ARP monitor will reliably detect link loss to an external switch. This is nothing unusual, but examination of the BladeCenter cabinet would suggest that the "external" network ports are the ethernet ports for the system, when it fact there is a switch between these "external" ports and the devices on the JS20 system itself. The MII monitor is only able to detect link failures between the ESM and the JS20 system. When a passthrough module is in place, the MII monitor does detect failures to the "external" port, which is then directly connected to the JS20 system. Other concerns -------------- The Serial Over LAN link is established over the primary ethernet (eth0) only, therefore, any loss of link to eth0 will result in losing your SoL connection. It will not fail over with other network traffic. It may be desirable to disable spanning tree on the switch (either the internal Ethernet Switch Module, or an external switch) to avoid fail-over delays issues when using bonding. 14. Frequently Asked Questions ============================== 1. Is it SMP safe? Yes. The old 2.0.xx channel bonding patch was not SMP safe. The new driver was designed to be SMP safe from the start. 2. What type of cards will work with it? Any Ethernet type cards (you can even mix cards - a Intel EtherExpress PRO/100 and a 3com 3c905b, for example). They need not be of the same speed. 3. How many bonding devices can I have? There is no limit. 4. How many slaves can a bonding device have? This is limited only by the number of network interfaces Linux supports and/or the number of network cards you can place in your system. 5. What happens when a slave link dies? If link monitoring is enabled, then the failing device will be disabled. The active-backup mode will fail over to a backup link, and other modes will ignore the failed link. The link will continue to be monitored, and should it recover, it will rejoin the bond (in whatever manner is appropriate for the mode). See the section on High Availability for additional information. Link monitoring can be enabled via either the miimon or arp_interval paramters (described in the module paramters section, above). In general, miimon monitors the carrier state as sensed by the underlying network device, and the arp monitor (arp_interval) monitors connectivity to another host on the local network. If no link monitoring is configured, the bonding driver will be unable to detect link failures, and will assume that all links are always available. This will likely result in lost packets, and a resulting degredation of performance. The precise performance loss depends upon the bonding mode and network configuration. 6. Can bonding be used for High Availability? Yes. See the section on High Availability for details. 7. Which switches/systems does it work with? The full answer to this depends upon the desired mode. In the basic balance modes (balance-rr and balance-xor), it works with any system that supports etherchannel (also called trunking). Most managed switches currently available have such support, and many unmananged switches as well. The advanced balance modes (balance-tlb and balance-alb) do not have special switch requirements, but do need device drivers that support specific features (described in the appropriate section under module paramters, above). In 802.3ad mode, it works with with systems that support IEEE 802.3ad Dynamic Link Aggregation. Most managed and many unmanaged switches currently available support 802.3ad. The active-backup mode should work with any Layer-II switch. 8. Where does a bonding device get its MAC address from? If not explicitly configured with ifconfig, the MAC address of the bonding device is taken from its first slave device. This MAC address is then passed to all following slaves and remains persistent (even if the the first slave is removed) until the bonding device is brought down or reconfigured. If you wish to change the MAC address, you can set it with ifconfig: # ifconfig bond0 hw ether 00:11:22:33:44:55 The MAC address can be also changed by bringing down/up the device and then changing its slaves (or their order): # ifconfig bond0 down ; modprobe -r bonding # ifconfig bond0 .... up # ifenslave bond0 eth... This method will automatically take the address from the next slave that is added. To restore your slaves' MAC addresses, you need to detach them from the bond (`ifenslave -d bond0 eth0'). The bonding driver will then restore the MAC addresses that the slaves had before they were enslaved. 15. Resources and Links ======================= The latest version of the bonding driver can be found in the latest version of the linux kernel, found on http://kernel.org Discussions regarding the bonding driver take place primarily on the bonding-devel mailing list, hosted at sourceforge.net. If you have questions or problems, post them to the list. bonding-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bonding-devel There is also a project site on sourceforge. http://www.sourceforge.net/projects/bonding Donald Becker's Ethernet Drivers and diag programs may be found at : - http://www.scyld.com/network/ You will also find a lot of information regarding Ethernet, NWay, MII, etc. at www.scyld.com. -- END --