/* * Copyright 2004-2009 Analog Devices Inc. * 2008-2009 Bluetechnix * 2005 National ICT Australia (NICTA) * Aidan Williams * * Licensed under the GPL-2 or later. */ #include #include #include #include #include #include #include #include #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) #include #endif #include #include #include #include #include /* * Name the Board for the /proc/cpuinfo */ const char bfin_board_name[] = "Bluetechnix CM BF533"; #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) /* all SPI peripherals info goes here */ #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) static struct mtd_partition bfin_spi_flash_partitions[] = { { .name = "bootloader(spi)", .size = 0x00020000, .offset = 0, .mask_flags = MTD_CAP_ROM }, { .name = "linux kernel(spi)", .size = 0xe0000, .offset = 0x20000 }, { .name = "file system(spi)", .size = 0x700000, .offset = 0x00100000, } }; static struct flash_platform_data bfin_spi_flash_data = { .name = "m25p80", .parts = bfin_spi_flash_partitions, .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), .type = "m25p64", }; /* SPI flash chip (m25p64) */ static struct bfin5xx_spi_chip spi_flash_chip_info = { .enable_dma = 0, /* use dma transfer with this chip*/ .bits_per_word = 8, }; #endif /* SPI ADC chip */ #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) static struct bfin5xx_spi_chip spi_adc_chip_info = { .enable_dma = 1, /* use dma transfer with this chip*/ .bits_per_word = 16, }; #endif #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) static struct bfin5xx_spi_chip ad1836_spi_chip_info = { .enable_dma = 0, .bits_per_word = 16, }; #endif #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) static struct bfin5xx_spi_chip mmc_spi_chip_info = { .enable_dma = 0, .bits_per_word = 8, }; #endif static struct spi_board_info bfin_spi_board_info[] __initdata = { #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE) { /* the modalias must be the same as spi device driver name */ .modalias = "m25p80", /* Name of spi_driver for this device */ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, /* Framework bus number */ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ .platform_data = &bfin_spi_flash_data, .controller_data = &spi_flash_chip_info, .mode = SPI_MODE_3, }, #endif #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE) { .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, /* Framework bus number */ .chip_select = 2, /* Framework chip select. */ .platform_data = NULL, /* No spi_driver specific config */ .controller_data = &spi_adc_chip_info, }, #endif #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) { .modalias = "ad1836", .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, .controller_data = &ad1836_spi_chip_info, }, #endif #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) { .modalias = "mmc_spi", .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, .chip_select = 1, .controller_data = &mmc_spi_chip_info, .mode = SPI_MODE_3, }, #endif }; /* SPI (0) */ static struct resource bfin_spi0_resource[] = { [0] = { .start = SPI0_REGBASE, .end = SPI0_REGBASE + 0xFF, .flags = IORESOURCE_MEM, }, [1] = { .start = CH_SPI, .end = CH_SPI, .flags = IORESOURCE_DMA, }, [2] = { .start = IRQ_SPI, .end = IRQ_SPI, .flags = IORESOURCE_IRQ, } }; /* SPI controller data */ static struct bfin5xx_spi_master bfin_spi0_info = { .num_chipselect = 8, .enable_dma = 1, /* master has the ability to do dma transfer */ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, }; static struct platform_device bfin_spi0_device = { .name = "bfin-spi", .id = 0, /* Bus number */ .num_resources = ARRAY_SIZE(bfin_spi0_resource), .resource = bfin_spi0_resource, .dev = { .platform_data = &bfin_spi0_info, /* Passed to driver */ }, }; #endif /* spi master and devices */ #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) static struct platform_device rtc_device = { .name = "rtc-bfin", .id = -1, }; #endif #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) #include static struct smc91x_platdata smc91x_info = { .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, .leda = RPC_LED_100_10, .ledb = RPC_LED_TX_RX, }; static struct resource smc91x_resources[] = { { .start = 0x20200300, .end = 0x20200300 + 16, .flags = IORESOURCE_MEM, }, { .start = IRQ_PF0, .end = IRQ_PF0, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, }, }; static struct platform_device smc91x_device = { .name = "smc91x", .id = 0, .num_resources = ARRAY_SIZE(smc91x_resources), .resource = smc91x_resources, .dev = { .platform_data = &smc91x_info, }, }; #endif #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include static struct resource smsc911x_resources[] = { { .name = "smsc911x-memory", .start = 0x20308000, .end = 0x20308000 + 0xFF, .flags = IORESOURCE_MEM, }, { .start = IRQ_PF8, .end = IRQ_PF8, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, }, }; static struct smsc911x_platform_config smsc911x_config = { .flags = SMSC911X_USE_16BIT, .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, .phy_interface = PHY_INTERFACE_MODE_MII, }; static struct platform_device smsc911x_device = { .name = "smsc911x", .id = 0, .num_resources = ARRAY_SIZE(smsc911x_resources), .resource = smsc911x_resources, .dev = { .platform_data = &smsc911x_config, }, }; #endif #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) #ifdef CONFIG_SERIAL_BFIN_UART0 static struct resource bfin_uart0_resources[] = { { .start = BFIN_UART_THR, .end = BFIN_UART_GCTL+2, .flags = IORESOURCE_MEM, }, { .start = IRQ_UART0_RX, .end = IRQ_UART0_RX + 1, .flags = IORESOURCE_IRQ, }, { .start = IRQ_UART0_ERROR, .end = IRQ_UART0_ERROR, .flags = IORESOURCE_IRQ, }, { .start = CH_UART0_TX, .end = CH_UART0_TX, .flags = IORESOURCE_DMA, }, { .start = CH_UART0_RX, .end = CH_UART0_RX, .flags = IORESOURCE_DMA, }, }; unsigned short bfin_uart0_peripherals[] = { P_UART0_TX, P_UART0_RX, 0 }; static struct platform_device bfin_uart0_device = { .name = "bfin-uart", .id = 0, .num_resources = ARRAY_SIZE(bfin_uart0_resources), .resource = bfin_uart0_resources, .dev = { .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ }, }; #endif #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) #ifdef CONFIG_BFIN_SIR0 static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, { .start = IRQ_UART0_RX, .end = IRQ_UART0_RX+1, .flags = IORESOURCE_IRQ, }, { .start = CH_UART0_RX, .end = CH_UART0_RX+1, .flags = IORESOURCE_DMA, }, }; static struct platform_device bfin_sir0_device = { .name = "bfin_sir", .id = 0, .num_resources = ARRAY_SIZE(bfin_sir0_resources), .resource = bfin_sir0_resources, }; #endif #endif #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART static struct resource bfin_sport0_uart_resources[] = { { .start = SPORT0_TCR1, .end = SPORT0_MRCS3+4, .flags = IORESOURCE_MEM, }, { .start = IRQ_SPORT0_RX, .end = IRQ_SPORT0_RX+1, .flags = IORESOURCE_IRQ, }, { .start = IRQ_SPORT0_ERROR, .end = IRQ_SPORT0_ERROR, .flags = IORESOURCE_IRQ, }, }; unsigned short bfin_sport0_peripherals[] = { P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0 }; static struct platform_device bfin_sport0_uart_device = { .name = "bfin-sport-uart", .id = 0, .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources), .resource = bfin_sport0_uart_resources, .dev = { .platform_data = &bfin_sport0_peripherals, /* Passed to driver */ }, }; #endif #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART static struct resource bfin_sport1_uart_resources[] = { { .start = SPORT1_TCR1, .end = SPORT1_MRCS3+4, .flags = IORESOURCE_MEM, }, { .start = IRQ_SPORT1_RX, .end = IRQ_SPORT1_RX+1, .flags = IORESOURCE_IRQ, }, { .start = IRQ_SPORT1_ERROR, .end = IRQ_SPORT1_ERROR, .flags = IORESOURCE_IRQ, }, }; unsigned short bfin_sport1_peripherals[] = { P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0 }; static struct platform_device bfin_sport1_uart_device = { .name = "bfin-sport-uart", .id = 1, .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources), .resource = bfin_sport1_uart_resources, .dev = { .platform_data = &bfin_sport1_peripherals, /* Passed to driver */ }, }; #endif #endif #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) static struct resource isp1362_hcd_resources[] = { { .start = 0x20308000, .end = 0x20308000, .flags = IORESOURCE_MEM, }, { .start = 0x20308004, .end = 0x20308004, .flags = IORESOURCE_MEM, }, { .start = IRQ_PF4, .end = IRQ_PF4, .flags = IORESOURCE_IRQ, }, }; static struct isp1362_platform_data isp1362_priv = { .sel15Kres = 1, .clknotstop = 0, .oc_enable = 0, .int_act_high = 0, .int_edge_triggered = 0, .remote_wakeup_connected = 0, .no_power_switching = 1, .power_switching_mode = 0, }; static struct platform_device isp1362_hcd_device = { .name = "isp1362-hcd", .id = 0, .dev = { .platform_data = &isp1362_priv, }, .num_resources = ARRAY_SIZE(isp1362_hcd_resources), .resource = isp1362_hcd_resources, }; #endif #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) static struct resource net2272_bfin_resources[] = { { .start = 0x20300000, .end = 0x20300000 + 0x100, .flags = IORESOURCE_MEM, }, { .start = IRQ_PF6, .end = IRQ_PF6, .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, }, }; static struct platform_device net2272_bfin_device = { .name = "net2272", .id = -1, .num_resources = ARRAY_SIZE(net2272_bfin_resources), .resource = net2272_bfin_resources, }; #endif #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) static struct mtd_partition para_partitions[] = { { .name = "bootloader(nor)", .size = 0x40000, .offset = 0, }, { .name = "linux+rootfs(nor)", .size = MTDPART_SIZ_FULL, .offset = MTDPART_OFS_APPEND, }, }; static struct physmap_flash_data para_flash_data = { .width = 2, .parts = para_partitions, .nr_parts = ARRAY_SIZE(para_partitions), }; static struct resource para_flash_resource = { .start = 0x20000000, .end = 0x201fffff, .flags = IORESOURCE_MEM, }; static struct platform_device para_flash_device = { .name = "physmap-flash", .id = 0, .dev = { .platform_data = ¶_flash_data, }, .num_resources = 1, .resource = ¶_flash_resource, }; #endif static const unsigned int cclk_vlev_datasheet[] = { VRPAIR(VLEV_085, 250000000), VRPAIR(VLEV_090, 376000000), VRPAIR(VLEV_095, 426000000), VRPAIR(VLEV_100, 426000000), VRPAIR(VLEV_105, 476000000), VRPAIR(VLEV_110, 476000000), VRPAIR(VLEV_115, 476000000), VRPAIR(VLEV_120, 600000000), VRPAIR(VLEV_125, 600000000), VRPAIR(VLEV_130, 600000000), }; static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { .tuple_tab = cclk_vlev_datasheet, .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), .vr_settling_time = 25 /* us */, }; static struct platform_device bfin_dpmc = { .name = "bfin dpmc", .dev = { .platform_data = &bfin_dmpc_vreg_data, }, }; static struct platform_device *cm_bf533_devices[] __initdata = { &bfin_dpmc, #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) #ifdef CONFIG_SERIAL_BFIN_UART0 &bfin_uart0_device, #endif #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) #ifdef CONFIG_BFIN_SIR0 &bfin_sir0_device, #endif #endif #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART &bfin_sport0_uart_device, #endif #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART &bfin_sport1_uart_device, #endif #endif #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) &rtc_device, #endif #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) &isp1362_hcd_device, #endif #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) &smc91x_device, #endif #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) &smsc911x_device, #endif #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) &net2272_bfin_device, #endif #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) &bfin_spi0_device, #endif #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) ¶_flash_device, #endif }; static int __init cm_bf533_init(void) { printk(KERN_INFO "%s(): registering device resources\n", __func__); platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices)); #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info)); #endif return 0; } arch_initcall(cm_bf533_init); static struct platform_device *cm_bf533_early_devices[] __initdata = { #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) #ifdef CONFIG_SERIAL_BFIN_UART0 &bfin_uart0_device, #endif #endif #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE) #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART &bfin_sport0_uart_device, #endif #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART &bfin_sport1_uart_device, #endif #endif }; void __init native_machine_early_platform_add_devices(void) { printk(KERN_INFO "register early platform devices\n"); early_platform_add_devices(cm_bf533_early_devices, ARRAY_SIZE(cm_bf533_early_devices)); }