/* * arch/ppc/platforms/katana.c * * Board setup routines for the Artesyn Katana cPCI boards. * * Author: Tim Montgomery * Maintained by: Mark A. Greer * * Based on code done by Rabeeh Khoury - rabeeh@galileo.co.il * Based on code done by - Mark A. Greer * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ /* * Supports the Artesyn 750i, 752i, and 3750. The 752i is virtually identical * to the 750i except that it has an mv64460 bridge. */ #include #include #include #include #include #include #include #include #include #include #include #include #ifdef CONFIG_BOOTIMG #include #endif #include #include #include #include #include #include #include #include #include #include static struct mv64x60_handle bh; static katana_id_t katana_id; static void __iomem *cpld_base; static void __iomem *sram_base; static u32 katana_flash_size_0; static u32 katana_flash_size_1; static u32 katana_bus_frequency; static struct pci_controller katana_hose_a; unsigned char __res[sizeof(bd_t)]; /* PCI Interrupt routing */ static int __init katana_irq_lookup_750i(unsigned char idsel, unsigned char pin) { static char pci_irq_table[][4] = { /* * PCI IDSEL/INTPIN->INTLINE * A B C D */ /* IDSEL 4 (PMC 1) */ { KATANA_PCI_INTB_IRQ_750i, KATANA_PCI_INTC_IRQ_750i, KATANA_PCI_INTD_IRQ_750i, KATANA_PCI_INTA_IRQ_750i }, /* IDSEL 5 (PMC 2) */ { KATANA_PCI_INTC_IRQ_750i, KATANA_PCI_INTD_IRQ_750i, KATANA_PCI_INTA_IRQ_750i, KATANA_PCI_INTB_IRQ_750i }, /* IDSEL 6 (T8110) */ {KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 }, /* IDSEL 7 (unused) */ {0, 0, 0, 0 }, /* IDSEL 8 (Intel 82544) (752i only but doesn't harm 750i) */ {KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 }, }; const long min_idsel = 4, max_idsel = 8, irqs_per_slot = 4; return PCI_IRQ_TABLE_LOOKUP; } static int __init katana_irq_lookup_3750(unsigned char idsel, unsigned char pin) { static char pci_irq_table[][4] = { /* * PCI IDSEL/INTPIN->INTLINE * A B C D */ { KATANA_PCI_INTA_IRQ_3750, 0, 0, 0 }, /* IDSEL 3 (BCM5691) */ { KATANA_PCI_INTB_IRQ_3750, 0, 0, 0 }, /* IDSEL 4 (MV64360 #2)*/ { KATANA_PCI_INTC_IRQ_3750, 0, 0, 0 }, /* IDSEL 5 (MV64360 #3)*/ }; const long min_idsel = 3, max_idsel = 5, irqs_per_slot = 4; return PCI_IRQ_TABLE_LOOKUP; } static int __init katana_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) { switch (katana_id) { case KATANA_ID_750I: case KATANA_ID_752I: return katana_irq_lookup_750i(idsel, pin); case KATANA_ID_3750: return katana_irq_lookup_3750(idsel, pin); default: printk(KERN_ERR "Bogus board ID\n"); return 0; } } /* Board info retrieval routines */ void __init katana_get_board_id(void) { switch (in_8(cpld_base + KATANA_CPLD_PRODUCT_ID)) { case KATANA_PRODUCT_ID_3750: katana_id = KATANA_ID_3750; break; case KATANA_PRODUCT_ID_750i: katana_id = KATANA_ID_750I; break; case KATANA_PRODUCT_ID_752i: katana_id = KATANA_ID_752I; break; default: printk(KERN_ERR "Unsupported board\n"); } } int __init katana_get_proc_num(void) { u16 val; u8 save_exclude; static int proc = -1; static u8 first_time = 1; if (first_time) { if (katana_id != KATANA_ID_3750) proc = 0; else { save_exclude = mv64x60_pci_exclude_bridge; mv64x60_pci_exclude_bridge = 0; early_read_config_word(bh.hose_b, 0, PCI_DEVFN(0,0), PCI_DEVICE_ID, &val); mv64x60_pci_exclude_bridge = save_exclude; switch(val) { case PCI_DEVICE_ID_KATANA_3750_PROC0: proc = 0; break; case PCI_DEVICE_ID_KATANA_3750_PROC1: proc = 1; break; case PCI_DEVICE_ID_KATANA_3750_PROC2: proc = 2; break; default: printk(KERN_ERR "Bogus Device ID\n"); } } first_time = 0; } return proc; } static inline int katana_is_monarch(void) { return in_8(cpld_base + KATANA_CPLD_BD_CFG_3) & KATANA_CPLD_BD_CFG_3_MONARCH; } static void __init katana_setup_bridge(void) { struct pci_controller hose; struct mv64x60_setup_info si; void __iomem *vaddr; int i; u32 v; u16 val, type; u8 save_exclude; /* * Some versions of the Katana firmware mistakenly change the vendor * & device id fields in the bridge's pci device (visible via pci * config accesses). This breaks mv64x60_init() because those values * are used to identify the type of bridge that's there. Artesyn * claims that the subsystem vendor/device id's will have the correct * Marvell values so this code puts back the correct values from there. */ memset(&hose, 0, sizeof(hose)); vaddr = ioremap(CONFIG_MV64X60_NEW_BASE, MV64x60_INTERNAL_SPACE_SIZE); setup_indirect_pci_nomap(&hose, vaddr + MV64x60_PCI0_CONFIG_ADDR, vaddr + MV64x60_PCI0_CONFIG_DATA); save_exclude = mv64x60_pci_exclude_bridge; mv64x60_pci_exclude_bridge = 0; early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID, &val); if (val != PCI_VENDOR_ID_MARVELL) { early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_SUBSYSTEM_VENDOR_ID, &val); early_write_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID, val); early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_SUBSYSTEM_ID, &val); early_write_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_DEVICE_ID, val); } /* * While we're in here, set the hotswap register correctly. * Turn off blue LED; mask ENUM#, clear insertion & extraction bits. */ early_read_config_dword(&hose, 0, PCI_DEVFN(0, 0), MV64360_PCICFG_CPCI_HOTSWAP, &v); v &= ~(1<<19); v |= ((1<<17) | (1<<22) | (1<<23)); early_write_config_dword(&hose, 0, PCI_DEVFN(0, 0), MV64360_PCICFG_CPCI_HOTSWAP, v); /* While we're at it, grab the bridge type for later */ early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_DEVICE_ID, &type); mv64x60_pci_exclude_bridge = save_exclude; iounmap(vaddr); memset(&si, 0, sizeof(si)); si.phys_reg_base = CONFIG_MV64X60_NEW_BASE; si.pci_1.enable_bus = 1; si.pci_1.pci_io.cpu_base = KATANA_PCI1_IO_START_PROC_ADDR; si.pci_1.pci_io.pci_base_hi = 0; si.pci_1.pci_io.pci_base_lo = KATANA_PCI1_IO_START_PCI_ADDR; si.pci_1.pci_io.size = KATANA_PCI1_IO_SIZE; si.pci_1.pci_io.swap = MV64x60_CPU2PCI_SWAP_NONE; si.pci_1.pci_mem[0].cpu_base = KATANA_PCI1_MEM_START_PROC_ADDR; si.pci_1.pci_mem[0].pci_base_hi = KATANA_PCI1_MEM_START_PCI_HI_ADDR; si.pci_1.pci_mem[0].pci_base_lo = KATANA_PCI1_MEM_START_PCI_LO_ADDR; si.pci_1.pci_mem[0].size = KATANA_PCI1_MEM_SIZE; si.pci_1.pci_mem[0].swap = MV64x60_CPU2PCI_SWAP_NONE; si.pci_1.pci_cmd_bits = 0; si.pci_1.latency_timer = 0x80; for (i = 0; i < MV64x60_CPU2MEM_WINDOWS; i++) { #if defined(CONFIG_NOT_COHERENT_CACHE) si.cpu_prot_options[i] = 0; si.enet_options[i] = MV64360_ENET2MEM_SNOOP_NONE; si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_NONE; si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_NONE; si.pci_1.acc_cntl_options[i] = MV64360_PCI_ACC_CNTL_SNOOP_NONE | MV64360_PCI_ACC_CNTL_SWAP_NONE | MV64360_PCI_ACC_CNTL_MBURST_128_BYTES | MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES; #else si.cpu_prot_options[i] = 0; si.enet_options[i] = MV64360_ENET2MEM_SNOOP_WB; si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_WB; si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_WB; si.pci_1.acc_cntl_options[i] = MV64360_PCI_ACC_CNTL_SNOOP_WB | MV64360_PCI_ACC_CNTL_SWAP_NONE | MV64360_PCI_ACC_CNTL_MBURST_32_BYTES | ((type == PCI_DEVICE_ID_MARVELL_MV64360) ? MV64360_PCI_ACC_CNTL_RDSIZE_32_BYTES : MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES); #endif } /* Lookup PCI host bridges */ if (mv64x60_init(&bh, &si)) printk(KERN_WARNING "Bridge initialization failed.\n"); pci_dram_offset = 0; /* sys mem at same addr on PCI & cpu bus */ ppc_md.pci_swizzle = common_swizzle; ppc_md.pci_map_irq = katana_map_irq; ppc_md.pci_exclude_device = mv64x60_pci_exclude_device; mv64x60_set_bus(&bh, 1, 0); bh.hose_b->first_busno = 0; bh.hose_b->last_busno = 0xff; /* * Need to access hotswap reg which is in the pci config area of the * bridge's hose 0. Note that pcibios_alloc_controller() can't be used * to alloc hose_a b/c that would make hose 0 known to the generic * pci code which we don't want. */ bh.hose_a = &katana_hose_a; setup_indirect_pci_nomap(bh.hose_a, bh.v_base + MV64x60_PCI0_CONFIG_ADDR, bh.v_base + MV64x60_PCI0_CONFIG_DATA); } /* Bridge & platform setup routines */ void __init katana_intr_setup(void) { if (bh.type == MV64x60_TYPE_MV64460) /* As per instns from Marvell */ mv64x60_clr_bits(&bh, MV64x60_CPU_MASTER_CNTL, 1 << 15); /* MPP 8, 9, and 10 */ mv64x60_clr_bits(&bh, MV64x60_MPP_CNTL_1, 0xfff); /* MPP 14 */ if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) mv64x60_clr_bits(&bh, MV64x60_MPP_CNTL_1, 0x0f000000); /* * Define GPP 8,9,and 10 interrupt polarity as active low * input signal and level triggered */ mv64x60_set_bits(&bh, MV64x60_GPP_LEVEL_CNTL, 0x700); mv64x60_clr_bits(&bh, MV64x60_GPP_IO_CNTL, 0x700); if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) { mv64x60_set_bits(&bh, MV64x60_GPP_LEVEL_CNTL, (1<<14)); mv64x60_clr_bits(&bh, MV64x60_GPP_IO_CNTL, (1<<14)); } /* Config GPP intr ctlr to respond to level trigger */ mv64x60_set_bits(&bh, MV64x60_COMM_ARBITER_CNTL, (1<<10)); if (bh.type == MV64x60_TYPE_MV64360) { /* Erratum FEr PCI-#9 */ mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, (1<<4) | (1<<5) | (1<<6) | (1<<7)); mv64x60_set_bits(&bh, MV64x60_PCI1_CMD, (1<<8) | (1<<9)); } else { mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, (1<<6) | (1<<7)); mv64x60_set_bits(&bh, MV64x60_PCI1_CMD, (1<<4) | (1<<5) | (1<<8) | (1<<9)); } /* * Dismiss and then enable interrupt on GPP interrupt cause * for CPU #0 */ mv64x60_write(&bh, MV64x60_GPP_INTR_CAUSE, ~0x700); mv64x60_set_bits(&bh, MV64x60_GPP_INTR_MASK, 0x700); if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) { mv64x60_write(&bh, MV64x60_GPP_INTR_CAUSE, ~(1<<14)); mv64x60_set_bits(&bh, MV64x60_GPP_INTR_MASK, (1<<14)); } /* * Dismiss and then enable interrupt on CPU #0 high cause reg * BIT25 summarizes GPP interrupts 8-15 */ mv64x60_set_bits(&bh, MV64360_IC_CPU0_INTR_MASK_HI, (1<<25)); } void __init katana_setup_peripherals(void) { u32 base; /* Set up windows for boot CS, soldered & socketed flash, and CPLD */ mv64x60_set_32bit_window(&bh, MV64x60_CPU2BOOT_WIN, KATANA_BOOT_WINDOW_BASE, KATANA_BOOT_WINDOW_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2BOOT_WIN); /* Assume firmware set up window sizes correctly for dev 0 & 1 */ mv64x60_get_32bit_window(&bh, MV64x60_CPU2DEV_0_WIN, &base, &katana_flash_size_0); if (katana_flash_size_0 > 0) { mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_0_WIN, KATANA_SOLDERED_FLASH_BASE, katana_flash_size_0, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_0_WIN); } mv64x60_get_32bit_window(&bh, MV64x60_CPU2DEV_1_WIN, &base, &katana_flash_size_1); if (katana_flash_size_1 > 0) { mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_1_WIN, (KATANA_SOLDERED_FLASH_BASE + katana_flash_size_0), katana_flash_size_1, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_1_WIN); } mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_2_WIN, KATANA_SOCKET_BASE, KATANA_SOCKETED_FLASH_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_2_WIN); mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_3_WIN, KATANA_CPLD_BASE, KATANA_CPLD_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_3_WIN); cpld_base = ioremap(KATANA_CPLD_BASE, KATANA_CPLD_SIZE); mv64x60_set_32bit_window(&bh, MV64x60_CPU2SRAM_WIN, KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE, 0); bh.ci->enable_window_32bit(&bh, MV64x60_CPU2SRAM_WIN); sram_base = ioremap(KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE); /* Set up Enet->SRAM window */ mv64x60_set_32bit_window(&bh, MV64x60_ENET2MEM_4_WIN, KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE, 0x2); bh.ci->enable_window_32bit(&bh, MV64x60_ENET2MEM_4_WIN); /* Give enet r/w access to memory region */ mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_0, (0x3 << (4 << 1))); mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_1, (0x3 << (4 << 1))); mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_2, (0x3 << (4 << 1))); mv64x60_clr_bits(&bh, MV64x60_PCI1_PCI_DECODE_CNTL, (1 << 3)); mv64x60_clr_bits(&bh, MV64x60_TIMR_CNTR_0_3_CNTL, ((1 << 0) | (1 << 8) | (1 << 16) | (1 << 24))); /* Must wait until window set up before retrieving board id */ katana_get_board_id(); /* Enumerate pci bus (must know board id before getting proc number) */ if (katana_get_proc_num() == 0) bh.hose_b->last_busno = pciauto_bus_scan(bh.hose_b, 0); #if defined(CONFIG_NOT_COHERENT_CACHE) mv64x60_write(&bh, MV64360_SRAM_CONFIG, 0x00160000); #else mv64x60_write(&bh, MV64360_SRAM_CONFIG, 0x001600b2); #endif /* * Setting the SRAM to 0. Note that this generates parity errors on * internal data path in SRAM since it's first time accessing it * while after reset it's not configured. */ memset(sram_base, 0, MV64360_SRAM_SIZE); /* Only processor zero [on 3750] is an PCI interrupt controller */ if (katana_get_proc_num() == 0) katana_intr_setup(); } static void __init katana_enable_ipmi(void) { u8 reset_out; /* Enable access to IPMI ctlr by clearing IPMI PORTSEL bit in CPLD */ reset_out = in_8(cpld_base + KATANA_CPLD_RESET_OUT); reset_out &= ~KATANA_CPLD_RESET_OUT_PORTSEL; out_8(cpld_base + KATANA_CPLD_RESET_OUT, reset_out); } static void __init katana_setup_arch(void) { if (ppc_md.progress) ppc_md.progress("katana_setup_arch: enter", 0); set_tb(0, 0); #ifdef CONFIG_BLK_DEV_INITRD if (initrd_start) ROOT_DEV = Root_RAM0; else #endif #ifdef CONFIG_ROOT_NFS ROOT_DEV = Root_NFS; #else ROOT_DEV = Root_SDA2; #endif /* * Set up the L2CR register. * * 750FX has only L2E, L2PE (bits 2-8 are reserved) * DD2.0 has bug that requires the L2 to be in WRT mode * avoid dirty data in cache */ if (PVR_REV(mfspr(SPRN_PVR)) == 0x0200) { printk(KERN_INFO "DD2.0 detected. Setting L2 cache" "to Writethrough mode\n"); _set_L2CR(L2CR_L2E | L2CR_L2PE | L2CR_L2WT); } else _set_L2CR(L2CR_L2E | L2CR_L2PE); if (ppc_md.progress) ppc_md.progress("katana_setup_arch: calling setup_bridge", 0); katana_setup_bridge(); katana_setup_peripherals(); katana_enable_ipmi(); katana_bus_frequency = katana_bus_freq(cpld_base); printk(KERN_INFO "Artesyn Communication Products, LLC - Katana(TM)\n"); if (ppc_md.progress) ppc_md.progress("katana_setup_arch: exit", 0); } void katana_fixup_resources(struct pci_dev *dev) { u16 v16; pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, L1_CACHE_LINE_SIZE>>2); pci_read_config_word(dev, PCI_COMMAND, &v16); v16 |= PCI_COMMAND_INVALIDATE | PCI_COMMAND_FAST_BACK; pci_write_config_word(dev, PCI_COMMAND, v16); } static const unsigned int cpu_750xx[32] = { /* 750FX & 750GX */ 0, 0, 2, 2, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,/* 0-15*/ 16, 17, 18, 19, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 0 /*16-31*/ }; static int katana_get_cpu_freq(void) { unsigned long pll_cfg; pll_cfg = (mfspr(SPRN_HID1) & 0xf8000000) >> 27; return katana_bus_frequency * cpu_750xx[pll_cfg]/2; } /* Platform device data fixup routines. */ #if defined(CONFIG_SERIAL_MPSC) static void __init katana_fixup_mpsc_pdata(struct platform_device *pdev) { struct mpsc_pdata *pdata = (struct mpsc_pdata *)pdev->dev.platform_data; bd_t *bdp = (bd_t *)__res; if (bdp->bi_baudrate) pdata->default_baud = bdp->bi_baudrate; else pdata->default_baud = KATANA_DEFAULT_BAUD; pdata->max_idle = 40; pdata->brg_clk_src = KATANA_MPSC_CLK_SRC; /* * TCLK (not SysCLk) is routed to BRG, then to the MPSC. On most parts, * TCLK == SysCLK but on 64460, they are separate pins. * SysCLK can go up to 200 MHz but TCLK can only go up to 133 MHz. */ pdata->brg_clk_freq = min(katana_bus_frequency, MV64x60_TCLK_FREQ_MAX); } #endif #if defined(CONFIG_MV643XX_ETH) static void __init katana_fixup_eth_pdata(struct platform_device *pdev) { struct mv643xx_eth_platform_data *eth_pd; static u16 phy_addr[] = { KATANA_ETH0_PHY_ADDR, KATANA_ETH1_PHY_ADDR, KATANA_ETH2_PHY_ADDR, }; eth_pd = pdev->dev.platform_data; eth_pd->force_phy_addr = 1; eth_pd->phy_addr = phy_addr[pdev->id]; eth_pd->tx_queue_size = KATANA_ETH_TX_QUEUE_SIZE; eth_pd->rx_queue_size = KATANA_ETH_RX_QUEUE_SIZE; } #endif #if defined(CONFIG_SYSFS) static void __init katana_fixup_mv64xxx_pdata(struct platform_device *pdev) { struct mv64xxx_pdata *pdata = (struct mv64xxx_pdata *) pdev->dev.platform_data; /* Katana supports the mv64xxx hotswap register */ pdata->hs_reg_valid = 1; } #endif static int __init katana_platform_notify(struct device *dev) { static struct { char *bus_id; void ((*rtn)(struct platform_device *pdev)); } dev_map[] = { #if defined(CONFIG_SERIAL_MPSC) { MPSC_CTLR_NAME ".0", katana_fixup_mpsc_pdata }, { MPSC_CTLR_NAME ".1", katana_fixup_mpsc_pdata }, #endif #if defined(CONFIG_MV643XX_ETH) { MV643XX_ETH_NAME ".0", katana_fixup_eth_pdata }, { MV643XX_ETH_NAME ".1", katana_fixup_eth_pdata }, { MV643XX_ETH_NAME ".2", katana_fixup_eth_pdata }, #endif #if defined(CONFIG_SYSFS) { MV64XXX_DEV_NAME ".0", katana_fixup_mv64xxx_pdata }, #endif }; struct platform_device *pdev; int i; if (dev && dev->bus_id) for (i=0; ibus_id, dev_map[i].bus_id, BUS_ID_SIZE)) { pdev = container_of(dev, struct platform_device, dev); dev_map[i].rtn(pdev); } return 0; } #ifdef CONFIG_MTD_PHYSMAP #ifndef MB #define MB (1 << 20) #endif /* * MTD Layout depends on amount of soldered FLASH in system. Sizes in MB. * * FLASH Amount: 128 64 32 16 * ------------- --- -- -- -- * Monitor: 1 1 1 1 * Primary Kernel: 1.5 1.5 1.5 1.5 * Primary fs: 30 30 * Secondary Kernel: 1.5 1.5 N/A N/A * Secondary fs: N/A N/A * User: */ static int __init katana_setup_mtd(void) { u32 size; int ptbl_entries; static struct mtd_partition *ptbl; size = katana_flash_size_0 + katana_flash_size_1; if (!size) return -ENOMEM; ptbl_entries = (size >= (64*MB)) ? 6 : 4; if ((ptbl = kmalloc(ptbl_entries * sizeof(struct mtd_partition), GFP_KERNEL)) == NULL) { printk(KERN_WARNING "Can't alloc MTD partition table\n"); return -ENOMEM; } memset(ptbl, 0, ptbl_entries * sizeof(struct mtd_partition)); ptbl[0].name = "Monitor"; ptbl[0].size = KATANA_MTD_MONITOR_SIZE; ptbl[1].name = "Primary Kernel"; ptbl[1].offset = MTDPART_OFS_NXTBLK; ptbl[1].size = 0x00180000; /* 1.5 MB */ ptbl[2].name = "Primary Filesystem"; ptbl[2].offset = MTDPART_OFS_APPEND; ptbl[2].size = MTDPART_SIZ_FULL; /* Correct for 16 & 32 MB */ ptbl[ptbl_entries-1].name = "User FLASH"; ptbl[ptbl_entries-1].offset = KATANA_MTD_MONITOR_SIZE; ptbl[ptbl_entries-1].size = MTDPART_SIZ_FULL; if (size >= (64*MB)) { ptbl[2].size = 30*MB; ptbl[3].name = "Secondary Kernel"; ptbl[3].offset = MTDPART_OFS_NXTBLK; ptbl[3].size = 0x00180000; /* 1.5 MB */ ptbl[4].name = "Secondary Filesystem"; ptbl[4].offset = MTDPART_OFS_APPEND; ptbl[4].size = MTDPART_SIZ_FULL; } physmap_map.size = size; physmap_set_partitions(ptbl, ptbl_entries); return 0; } arch_initcall(katana_setup_mtd); #endif static void katana_restart(char *cmd) { ulong i = 10000000; /* issue hard reset to the reset command register */ out_8(cpld_base + KATANA_CPLD_RST_CMD, KATANA_CPLD_RST_CMD_HR); while (i-- > 0) ; panic("restart failed\n"); } static void katana_halt(void) { u8 v; /* Turn on blue LED to indicate its okay to remove */ if (katana_id == KATANA_ID_750I) { u32 v; u8 save_exclude; /* Set LOO bit in cPCI HotSwap reg of hose 0 to turn on LED. */ save_exclude = mv64x60_pci_exclude_bridge; mv64x60_pci_exclude_bridge = 0; early_read_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0), MV64360_PCICFG_CPCI_HOTSWAP, &v); v &= 0xff; v |= (1 << 19); early_write_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0), MV64360_PCICFG_CPCI_HOTSWAP, v); mv64x60_pci_exclude_bridge = save_exclude; } else if (katana_id == KATANA_ID_752I) { v = in_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF); v |= HSL_PLD_HOT_SWAP_LED_BIT; out_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF, v); } while (1) ; /* NOTREACHED */ } static void katana_power_off(void) { katana_halt(); /* NOTREACHED */ } static int katana_show_cpuinfo(struct seq_file *m) { char *s; seq_printf(m, "cpu freq\t: %dMHz\n", (katana_get_cpu_freq() + 500000) / 1000000); seq_printf(m, "bus freq\t: %ldMHz\n", ((long)katana_bus_frequency + 500000) / 1000000); seq_printf(m, "vendor\t\t: Artesyn Communication Products, LLC\n"); seq_printf(m, "board\t\t: "); switch (katana_id) { case KATANA_ID_3750: seq_printf(m, "Katana 3750"); break; case KATANA_ID_750I: seq_printf(m, "Katana 750i"); break; case KATANA_ID_752I: seq_printf(m, "Katana 752i"); break; default: seq_printf(m, "Unknown"); break; } seq_printf(m, " (product id: 0x%x)\n", in_8(cpld_base + KATANA_CPLD_PRODUCT_ID)); seq_printf(m, "pci mode\t: %sMonarch\n", katana_is_monarch()? "" : "Non-"); seq_printf(m, "hardware rev\t: 0x%x\n", in_8(cpld_base+KATANA_CPLD_HARDWARE_VER)); seq_printf(m, "pld rev\t\t: 0x%x\n", in_8(cpld_base + KATANA_CPLD_PLD_VER)); switch(bh.type) { case MV64x60_TYPE_GT64260A: s = "gt64260a"; break; case MV64x60_TYPE_GT64260B: s = "gt64260b"; break; case MV64x60_TYPE_MV64360: s = "mv64360"; break; case MV64x60_TYPE_MV64460: s = "mv64460"; break; default: s = "Unknown"; } seq_printf(m, "bridge type\t: %s\n", s); seq_printf(m, "bridge rev\t: 0x%x\n", bh.rev); #if defined(CONFIG_NOT_COHERENT_CACHE) seq_printf(m, "coherency\t: %s\n", "off"); #else seq_printf(m, "coherency\t: %s\n", "on"); #endif return 0; } static void __init katana_calibrate_decr(void) { u32 freq; freq = katana_bus_frequency / 4; printk(KERN_INFO "time_init: decrementer frequency = %lu.%.6lu MHz\n", (long)freq / 1000000, (long)freq % 1000000); tb_ticks_per_jiffy = freq / HZ; tb_to_us = mulhwu_scale_factor(freq, 1000000); } /* * The katana supports both uImage and zImage. If uImage, get the mem size * from the bd info. If zImage, the bootwrapper adds a BI_MEMSIZE entry in * the bi_rec data which is sucked out and put into boot_mem_size by * parse_bootinfo(). MMU_init() will then use the boot_mem_size for the mem * size and not call this routine. The only way this will fail is when a uImage * is used but the fw doesn't pass in a valid bi_memsize. This should never * happen, though. */ unsigned long __init katana_find_end_of_memory(void) { bd_t *bdp = (bd_t *)__res; return bdp->bi_memsize; } #if defined(CONFIG_I2C_MV64XXX) && defined(CONFIG_SENSORS_M41T00) extern ulong m41t00_get_rtc_time(void); extern int m41t00_set_rtc_time(ulong); static int __init katana_rtc_hookup(void) { struct timespec tv; ppc_md.get_rtc_time = m41t00_get_rtc_time; ppc_md.set_rtc_time = m41t00_set_rtc_time; tv.tv_nsec = 0; tv.tv_sec = (ppc_md.get_rtc_time)(); do_settimeofday(&tv); return 0; } late_initcall(katana_rtc_hookup); #endif #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE) static void __init katana_map_io(void) { io_block_mapping(0xf8100000, 0xf8100000, 0x00020000, _PAGE_IO); } #endif void __init platform_init(unsigned long r3, unsigned long r4, unsigned long r5, unsigned long r6, unsigned long r7) { parse_bootinfo(find_bootinfo()); /* ASSUMPTION: If both r3 (bd_t pointer) and r6 (cmdline pointer) * are non-zero, then we should use the board info from the bd_t * structure and the cmdline pointed to by r6 instead of the * information from birecs, if any. Otherwise, use the information * from birecs as discovered by the preceeding call to * parse_bootinfo(). This rule should work with both PPCBoot, which * uses a bd_t board info structure, and the kernel boot wrapper, * which uses birecs. */ if (r3 && r6) { /* copy board info structure */ memcpy((void *)__res, (void *)(r3+KERNELBASE), sizeof(bd_t)); /* copy command line */ *(char *)(r7+KERNELBASE) = 0; strcpy(cmd_line, (char *)(r6+KERNELBASE)); } #ifdef CONFIG_BLK_DEV_INITRD /* take care of initrd if we have one */ if (r4) { initrd_start = r4 + KERNELBASE; initrd_end = r5 + KERNELBASE; } #endif /* CONFIG_BLK_DEV_INITRD */ isa_mem_base = 0; ppc_md.setup_arch = katana_setup_arch; ppc_md.pcibios_fixup_resources = katana_fixup_resources; ppc_md.show_cpuinfo = katana_show_cpuinfo; ppc_md.init_IRQ = mv64360_init_irq; ppc_md.get_irq = mv64360_get_irq; ppc_md.restart = katana_restart; ppc_md.power_off = katana_power_off; ppc_md.halt = katana_halt; ppc_md.find_end_of_memory = katana_find_end_of_memory; ppc_md.calibrate_decr = katana_calibrate_decr; #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE) ppc_md.setup_io_mappings = katana_map_io; ppc_md.progress = mv64x60_mpsc_progress; mv64x60_progress_init(CONFIG_MV64X60_NEW_BASE); #endif #if defined(CONFIG_SERIAL_MPSC) || defined(CONFIG_MV643XX_ETH) platform_notify = katana_platform_notify; #endif }