1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
Device tree bindings for OMAP general purpose memory controllers (GPMC)
The actual devices are instantiated from the child nodes of a GPMC node.
Required properties:
- compatible: Should be set to one of the following:
ti,omap2420-gpmc (omap2420)
ti,omap2430-gpmc (omap2430)
ti,omap3430-gpmc (omap3430 & omap3630)
ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
ti,am3352-gpmc (am335x devices)
- reg: A resource specifier for the register space
(see the example below)
- ti,hwmods: Should be set to "ti,gpmc" until the DT transition is
completed.
- #address-cells: Must be set to 2 to allow memory address translation
- #size-cells: Must be set to 1 to allow CS address passing
- gpmc,num-cs: The maximum number of chip-select lines that controller
can support.
- gpmc,num-waitpins: The maximum number of wait pins that controller can
support.
- ranges: Must be set up to reflect the memory layout with four
integer values for each chip-select line in use:
<cs-number> 0 <physical address of mapping> <size>
Currently, calculated values derived from the contents
of the per-CS register GPMC_CONFIG7 (as set up by the
bootloader) are used for the physical address decoding.
As this will change in the future, filling correct
values here is a requirement.
Timing properties for child nodes. All are optional and default to 0.
- gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds
Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
- gpmc,cs-on-ns: Assertion time
- gpmc,cs-rd-off-ns: Read deassertion time
- gpmc,cs-wr-off-ns: Write deassertion time
ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
- gpmc,adv-on-ns: Assertion time
- gpmc,adv-rd-off-ns: Read deassertion time
- gpmc,adv-wr-off-ns: Write deassertion time
WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- gpmc,we-on-ns Assertion time
- gpmc,we-off-ns: Deassertion time
OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- gpmc,oe-on-ns: Assertion time
- gpmc,oe-off-ns: Deassertion time
Access time and cycle time timings (in nanoseconds) corresponding to
GPMC_CONFIG5:
- gpmc,page-burst-access-ns: Multiple access word delay
- gpmc,access-ns: Start-cycle to first data valid delay
- gpmc,rd-cycle-ns: Total read cycle time
- gpmc,wr-cycle-ns: Total write cycle time
- gpmc,bus-turnaround-ns: Turn-around time between successive accesses
- gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses
- gpmc,clk-activation-ns: GPMC clock activation time
- gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid
data
Boolean timing parameters. If property is present parameter enabled and
disabled if omitted:
- gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock
- gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock
- gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive
accesses to a different CS
- gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive
accesses to the same CS
- gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock
- gpmc,we-extra-delay: WE signal is delayed by half GPMC clock
- gpmc,time-para-granularity: Multiply all access times by 2
The following are only applicable to OMAP3+ and AM335x:
- gpmc,wr-access-ns: In synchronous write mode, for single or
burst accesses, defines the number of
GPMC_FCLK cycles from start access time
to the GPMC_CLK rising edge used by the
memory device for the first data capture.
- gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies
the time when the first data is driven on
the address-data bus.
GPMC chip-select settings properties for child nodes. All are optional.
- gpmc,burst-length Page/burst length. Must be 4, 8 or 16.
- gpmc,burst-wrap Enables wrap bursting
- gpmc,burst-read Enables read page/burst mode
- gpmc,burst-write Enables write page/burst mode
- gpmc,device-width Total width of device(s) connected to a GPMC
chip-select in bytes. The GPMC supports 8-bit
and 16-bit devices and so this property must be
1 or 2.
- gpmc,mux-add-data Address and data multiplexing configuration.
Valid values are 1 for address-address-data
multiplexing mode and 2 for address-data
multiplexing mode.
- gpmc,sync-read Enables synchronous read. Defaults to asynchronous
is this is not set.
- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous
is this is not set.
- gpmc,wait-pin Wait-pin used by client. Must be less than
"gpmc,num-waitpins".
- gpmc,wait-on-read Enables wait monitoring on reads.
- gpmc,wait-on-write Enables wait monitoring on writes.
Example for an AM33xx board:
gpmc: gpmc@50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
reg = <0x50000000 0x2000>;
interrupts = <100>;
gpmc,num-cs = <8>;
gpmc,num-waitpins = <2>;
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
/* child nodes go here */
};
|
