summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml
blob: e71d13c2d109ed027e056e72c1e36e0d442f7101 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX

maintainers:
  - Shawn Guo <shawnguo@kernel.org>

allOf:
  - $ref: "mmc-controller.yaml"

description: |
  The Enhanced Secure Digital Host Controller on Freescale i.MX family
  provides an interface for MMC, SD, and SDIO types of memory cards.

  This file documents differences between the core properties described
  by mmc.txt and the properties used by the sdhci-esdhc-imx driver.

properties:
  compatible:
    oneOf:
      - enum:
          - fsl,imx25-esdhc
          - fsl,imx35-esdhc
          - fsl,imx51-esdhc
          - fsl,imx53-esdhc
          - fsl,imx6q-usdhc
          - fsl,imx6sl-usdhc
          - fsl,imx6sx-usdhc
          - fsl,imx6ull-usdhc
          - fsl,imx7d-usdhc
          - fsl,imx7ulp-usdhc
      - items:
          - enum:
              - fsl,imx8mm-usdhc
              - fsl,imx8mn-usdhc
              - fsl,imx8mp-usdhc
              - fsl,imx8mq-usdhc
              - fsl,imx8qxp-usdhc
          - const: fsl,imx7d-usdhc

  reg:
    maxItems: 1

  interrupts:
    maxItems: 1

  fsl,wp-controller:
    description: |
      boolean, if present, indicate to use controller internal write protection.
    type: boolean

  fsl,delay-line:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: |
      Specify the number of delay cells for override mode.
      This is used to set the clock delay for DLL(Delay Line) on override mode
      to select a proper data sampling window in case the clock quality is not good
      due to signal path is too long on the board. Please refer to eSDHC/uSDHC
      chapter, DLL (Delay Line) section in RM for details.
    default: 0

  voltage-ranges:
    $ref: '/schemas/types.yaml#/definitions/uint32-matrix'
    description: |
      Specify the voltage range in case there are software transparent level
      shifters on the outputs of the controller. Two cells are required, first
      cell specifies minimum slot voltage (mV), second cell specifies maximum
      slot voltage (mV).
    items:
      items:
        - description: value for minimum slot voltage
        - description: value for maximum slot voltage
    maxItems: 1

  fsl,tuning-start-tap:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: |
      Specify the start delay cell point when send first CMD19 in tuning procedure.
    default: 0

  fsl,tuning-step:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: |
      Specify the increasing delay cell steps in tuning procedure.
      The uSDHC use one delay cell as default increasing step to do tuning process.
      This property allows user to change the tuning step to more than one delay
      cells which is useful for some special boards or cards when the default
      tuning step can't find the proper delay window within limited tuning retries.
    default: 0

  fsl,strobe-dll-delay-target:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: |
      Specify the strobe dll control slave delay target.
      This delay target programming host controller loopback read clock, and this
      property allows user to change the delay target for the strobe input read clock.
      If not use this property, driver default set the delay target to value 7.
      Only eMMC HS400 mode need to take care of this property.
    default: 0

required:
  - compatible
  - reg
  - interrupts

unevaluatedProperties: false

examples:
  - |
    mmc@70004000 {
        compatible = "fsl,imx51-esdhc";
        reg = <0x70004000 0x4000>;
        interrupts = <1>;
        fsl,wp-controller;
    };

    mmc@70008000 {
        compatible = "fsl,imx51-esdhc";
        reg = <0x70008000 0x4000>;
        interrupts = <2>;
        cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */
        wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */
    };