1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
|
Samsung GPIO and Pin Mux/Config controller
Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
controller. It controls the input/output settings on the available pads/pins
and also provides ability to multiplex and configure the output of various
on-chip controllers onto these pads.
Required Properties:
- compatible: should be one of the following.
- "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller,
- "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller,
- "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
- "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
- "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
- "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
- "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
- "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
- "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller.
- reg: Base address of the pin controller hardware module and length of
the address space it occupies.
- Pin banks as child nodes: Pin banks of the controller are represented by child
nodes of the controller node. Bank name is taken from name of the node. Each
bank node must contain following properties:
- gpio-controller: identifies the node as a gpio controller and pin bank.
- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
binding is used, the amount of cells must be specified as 2. See the below
mentioned gpio binding representation for description of particular cells.
Eg: <&gpx2 6 0>
<[phandle of the gpio controller node]
[pin number within the gpio controller]
[flags]>
Values for gpio specifier:
- Pin number: is a value between 0 to 7.
- Flags: 0 - Active High
1 - Active Low
- Pin mux/config groups as child nodes: The pin mux (selecting pin function
mode) and pin config (pull up/down, driver strength) settings are represented
as child nodes of the pin-controller node. There should be atleast one
child node and there is no limit on the count of these child nodes.
The child node should contain a list of pin(s) on which a particular pin
function selection or pin configuration (or both) have to applied. This
list of pins is specified using the property name "samsung,pins". There
should be atleast one pin specfied for this property and there is no upper
limit on the count of pins that can be specified. The pins are specified
using pin names which are derived from the hardware manual of the SoC. As
an example, the pins in GPA0 bank of the pin controller can be represented
as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
The format of the pin names should be (as per the hardware manual)
"[pin bank name]-[pin number within the bank]".
The pin function selection that should be applied on the pins listed in the
child node is specified using the "samsung,pin-function" property. The value
of this property that should be applied to each of the pins listed in the
"samsung,pins" property should be picked from the hardware manual of the SoC
for the specified pin group. This property is optional in the child node if
no specific function selection is desired for the pins listed in the child
node. The value of this property is used as-is to program the pin-controller
function selector register of the pin-bank.
The child node can also optionally specify one or more of the pin
configuration that should be applied on all the pins listed in the
"samsung,pins" property of the child node. The following pin configuration
properties are supported.
- samsung,pin-pud: Pull up/down configuration.
- samsung,pin-drv: Drive strength configuration.
- samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
- samsung,pin-drv-pdn: Drive strength configuration in power down mode.
The values specified by these config properties should be derived from the
hardware manual and these values are programmed as-is into the pin
pull up/down and driver strength register of the pin-controller.
Note: A child should include atleast a pin function selection property or
pin configuration property (one or more) or both.
The client nodes that require a particular pin function selection and/or
pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
file.
External GPIO and Wakeup Interrupts:
The controller supports two types of external interrupts over gpio. The first
is the external gpio interrupt and second is the external wakeup interrupts.
The difference between the two is that the external wakeup interrupts can be
used as system wakeup events.
A. External GPIO Interrupts: For supporting external gpio interrupts, the
following properties should be specified in the pin-controller device node.
- interrupt-parent: phandle of the interrupt parent to which the external
GPIO interrupts are forwarded to.
- interrupts: interrupt specifier for the controller. The format and value of
the interrupt specifier depends on the interrupt parent for the controller.
In addition, following properties must be present in node of every bank
of pins supporting GPIO interrupts:
- interrupt-controller: identifies the controller node as interrupt-parent.
- #interrupt-cells: the value of this property should be 2.
- First Cell: represents the external gpio interrupt number local to the
external gpio interrupt space of the controller.
- Second Cell: flags to identify the type of the interrupt
- 1 = rising edge triggered
- 2 = falling edge triggered
- 3 = rising and falling edge triggered
- 4 = high level triggered
- 8 = low level triggered
B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
child node representing the external wakeup interrupt controller should be
included in the pin-controller device node. This child node should include
the following properties.
- compatible: identifies the type of the external wakeup interrupt controller
The possible values are:
- samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller
found on Samsung S3C24xx SoCs except S3C2412 and S3C2413,
- samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller
found on Samsung S3C2412 and S3C2413 SoCs,
- samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
found on Samsung S3C64xx SoCs,
- samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
found on Samsung Exynos4210 SoC.
- interrupt-parent: phandle of the interrupt parent to which the external
wakeup interrupts are forwarded to.
- interrupts: interrupt used by multiplexed wakeup interrupts.
In addition, following properties must be present in node of every bank
of pins supporting wake-up interrupts:
- interrupt-controller: identifies the node as interrupt-parent.
- #interrupt-cells: the value of this property should be 2
- First Cell: represents the external wakeup interrupt number local to
the external wakeup interrupt space of the controller.
- Second Cell: flags to identify the type of the interrupt
- 1 = rising edge triggered
- 2 = falling edge triggered
- 3 = rising and falling edge triggered
- 4 = high level triggered
- 8 = low level triggered
Node of every bank of pins supporting direct wake-up interrupts (without
multiplexing) must contain following properties:
- interrupt-parent: phandle of the interrupt parent to which the external
wakeup interrupts are forwarded to.
- interrupts: interrupts of the interrupt parent which are used for external
wakeup interrupts from pins of the bank, must contain interrupts for all
pins of the bank.
Aliases:
All the pin controller nodes should be represented in the aliases node using
the following format 'pinctrl{n}' where n is a unique number for the alias.
Example: A pin-controller node with pin banks:
pinctrl_0: pinctrl@11400000 {
compatible = "samsung,exynos4210-pinctrl";
reg = <0x11400000 0x1000>;
interrupts = <0 47 0>;
/* ... */
/* Pin bank without external interrupts */
gpy0: gpy0 {
gpio-controller;
#gpio-cells = <2>;
};
/* ... */
/* Pin bank with external GPIO or muxed wake-up interrupts */
gpj0: gpj0 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
/* ... */
/* Pin bank with external direct wake-up interrupts */
gpx0: gpx0 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
interrupt-parent = <&gic>;
interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
#interrupt-cells = <2>;
};
/* ... */
};
Example 1: A pin-controller node with pin groups.
pinctrl_0: pinctrl@11400000 {
compatible = "samsung,exynos4210-pinctrl";
reg = <0x11400000 0x1000>;
interrupts = <0 47 0>;
/* ... */
uart0_data: uart0-data {
samsung,pins = "gpa0-0", "gpa0-1";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
uart0_fctl: uart0-fctl {
samsung,pins = "gpa0-2", "gpa0-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
uart1_data: uart1-data {
samsung,pins = "gpa0-4", "gpa0-5";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
uart1_fctl: uart1-fctl {
samsung,pins = "gpa0-6", "gpa0-7";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
i2c2_bus: i2c2-bus {
samsung,pins = "gpa0-6", "gpa0-7";
samsung,pin-function = <3>;
samsung,pin-pud = <3>;
samsung,pin-drv = <0>;
};
};
Example 2: A pin-controller node with external wakeup interrupt controller node.
pinctrl_1: pinctrl@11000000 {
compatible = "samsung,exynos4210-pinctrl";
reg = <0x11000000 0x1000>;
interrupts = <0 46 0>
/* ... */
wakeup-interrupt-controller {
compatible = "samsung,exynos4210-wakeup-eint";
interrupt-parent = <&gic>;
interrupts = <0 32 0>;
};
};
Example 3: A uart client node that supports 'default' and 'flow-control' states.
uart@13800000 {
compatible = "samsung,exynos4210-uart";
reg = <0x13800000 0x100>;
interrupts = <0 52 0>;
pinctrl-names = "default", "flow-control;
pinctrl-0 = <&uart0_data>;
pinctrl-1 = <&uart0_data &uart0_fctl>;
};
Example 4: Set up the default pin state for uart controller.
static int s3c24xx_serial_probe(struct platform_device *pdev) {
struct pinctrl *pinctrl;
/* ... */
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
}
Example 5: A display port client node that supports 'default' pinctrl state
and gpio binding.
display-port-controller {
/* ... */
samsung,hpd-gpio = <&gpx2 6 0>;
pinctrl-names = "default";
pinctrl-0 = <&dp_hpd>;
};
Example 6: Request the gpio for display port controller
static int exynos_dp_probe(struct platform_device *pdev)
{
int hpd_gpio, ret;
struct device *dev = &pdev->dev;
struct device_node *dp_node = dev->of_node;
/* ... */
hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);
/* ... */
ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
"hpd_gpio");
/* ... */
}
|
