blob: cac6cf2e9ac84c672ba4dad57dca6035882cde50 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
config MAC80211
tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
depends on EXPERIMENTAL
select CRYPTO
select CRYPTO_ECB
select CRYPTO_ARC4
select CRYPTO_AES
select CRC32
select WIRELESS_EXT
select CFG80211
select NET_SCH_FIFO
---help---
This option enables the hardware independent IEEE 802.11
networking stack.
config MAC80211_RC_DEFAULT_CHOICE
bool "Choose default rate control algorithm" if EMBEDDED
default y
depends on MAC80211
---help---
This options enables selection of a default rate control
algorithm to be built into the mac80211 module. Alternate
rate control algorithms might be built into the mac80211
module as well.
choice
prompt "Default rate control algorithm"
default MAC80211_RC_DEFAULT_PID
depends on MAC80211 && MAC80211_RC_DEFAULT_CHOICE
---help---
This option selects the default rate control algorithm
mac80211 will use. Note that this default can still be
overriden through the ieee80211_default_rc_algo module
parameter.
config MAC80211_RC_DEFAULT_PID
bool "PID controller based rate control algorithm"
select MAC80211_RC_PID
---help---
Select the PID controller based rate control as the
default rate control algorithm. You should choose
this unless you know what you are doing.
config MAC80211_RC_DEFAULT_SIMPLE
bool "Simple rate control algorithm"
select MAC80211_RC_SIMPLE
---help---
Select the simple rate control as the default rate
control algorithm. Note that this is a non-responsive,
dumb algorithm. You should choose the PID rate control
instead.
endchoice
config MAC80211_RC_DEFAULT
string
depends on MAC80211
default "pid" if MAC80211_RC_DEFAULT_PID
default "simple" if MAC80211_RC_DEFAULT_SIMPLE
default ""
config MAC80211_RC_PID
bool "PID controller based rate control algorithm"
default y
depends on MAC80211
---help---
This option enables a TX rate control algorithm for
mac80211 that uses a PID controller to select the TX
rate.
Say Y or M unless you're sure you want to use a
different rate control algorithm.
config MAC80211_RC_SIMPLE
bool "Simple rate control algorithm (DEPRECATED)"
default n
depends on MAC80211
---help---
This option enables a very simple, non-responsive TX
rate control algorithm. This algorithm is deprecated
and will be removed from the kernel in near future.
It has been replaced by the PID algorithm.
Say N unless you know what you are doing.
config MAC80211_LEDS
bool "Enable LED triggers"
depends on MAC80211 && LEDS_TRIGGERS
---help---
This option enables a few LED triggers for different
packet receive/transmit events.
config MAC80211_DEBUGFS
bool "Export mac80211 internals in DebugFS"
depends on MAC80211 && DEBUG_FS
---help---
Select this to see extensive information about
the internal state of mac80211 in debugfs.
Say N unless you know you need this.
config MAC80211_DEBUG
bool "Enable debugging output"
depends on MAC80211
---help---
This option will enable debug tracing output for the
ieee80211 network stack.
If you are not trying to debug or develop the ieee80211
subsystem, you most likely want to say N here.
config MAC80211_HT_DEBUG
bool "Enable HT debugging output"
depends on MAC80211_DEBUG
---help---
This option enables 802.11n High Throughput features
debug tracing output.
If you are not trying to debug of develop the ieee80211
subsystem, you most likely want to say N here.
config MAC80211_VERBOSE_DEBUG
bool "Verbose debugging output"
depends on MAC80211_DEBUG
config MAC80211_LOWTX_FRAME_DUMP
bool "Debug frame dumping"
depends on MAC80211_DEBUG
---help---
Selecting this option will cause the stack to
print a message for each frame that is handed
to the lowlevel driver for transmission. This
message includes all MAC addresses and the
frame control field.
If unsure, say N and insert the debugging code
you require into the driver you are debugging.
config TKIP_DEBUG
bool "TKIP debugging"
depends on MAC80211_DEBUG
config MAC80211_DEBUG_COUNTERS
bool "Extra statistics for TX/RX debugging"
depends on MAC80211_DEBUG
config MAC80211_IBSS_DEBUG
bool "Support for IBSS testing"
depends on MAC80211_DEBUG
---help---
Say Y here if you intend to debug the IBSS code.
config MAC80211_VERBOSE_PS_DEBUG
bool "Verbose powersave mode debugging"
depends on MAC80211_DEBUG
---help---
Say Y here to print out verbose powersave
mode debug messages.
|
