summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorRon Madrid <ron_madrid@sbcglobal.net>2009-01-22 15:05:24 -0800
committerKim Phillips <kim.phillips@freescale.com>2009-01-23 11:31:18 -0600
commit5bb907a4925397789c90d074f4f7e92ce6b39402 (patch)
tree253d0d413aefbac48c7c9d526ef2d98eac49f108
parent6677876181cc8772bca8a372479a500d160f3993 (diff)
mpc83xx: New board support for SIMPC8313
This patch will create a new board, SIMPC8313, from Sheldon Instruments. This board boots from NAND devices and is configureable for either large or small page devices. The board supports non-soldered DDR2, one ethernet port, a Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected to the eLBC providing glue logic to a TMS320C67xx DSP. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
-rw-r--r--MAINTAINERS4
-rwxr-xr-xMAKEALL1
-rw-r--r--Makefile15
-rw-r--r--board/sheldon/simpc8313/Makefile50
-rw-r--r--board/sheldon/simpc8313/config.mk13
-rw-r--r--board/sheldon/simpc8313/sdram.c193
-rw-r--r--board/sheldon/simpc8313/simpc8313.c134
-rw-r--r--doc/README.simpc831380
-rw-r--r--include/configs/SIMPC8313.h544
-rw-r--r--nand_spl/board/sheldon/simpc8313/Makefile100
-rw-r--r--nand_spl/board/sheldon/simpc8313/u-boot.lds52
11 files changed, 1186 insertions, 0 deletions
diff --git a/MAINTAINERS b/MAINTAINERS
index d07fe86129..b774938dca 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -263,6 +263,10 @@ Jon Loeliger <jdl@freescale.com>
MPC8641HPCN MPC8641D
+Ron Madrid <info@sheldoninst.com>
+
+ SIMPC8313 MPC8313
+
Dan Malek <dan@embeddedalley.com>
stxgp3 MPC85xx
diff --git a/MAKEALL b/MAKEALL
index 3e8c56b4fd..1ca5e58ded 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -353,6 +353,7 @@ LIST_83xx=" \
MPC837XERDB \
MVBLM7 \
sbc8349 \
+ SIMPC8313_LP \
TQM834x \
"
diff --git a/Makefile b/Makefile
index 294efef943..9f69278156 100644
--- a/Makefile
+++ b/Makefile
@@ -2328,6 +2328,21 @@ MVBLM7_config: unconfig
sbc8349_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
+SIMPC8313_LP_config \
+SIMPC8313_SP_config: unconfig
+ @mkdir -p $(obj)include
+ @mkdir -p $(obj)board/sheldon/simpc8313
+ @if [ "$(findstring _LP_,$@)" ] ; then \
+ $(XECHO) -n "...Large Page NAND..." ; \
+ echo "#define CONFIG_NAND_LP" >> $(obj)include/config.h ; \
+ fi ; \
+ if [ "$(findstring _SP_,$@)" ] ; then \
+ $(XECHO) -n "...Small Page NAND..." ; \
+ echo "#define CONFIG_NAND_SP" >> $(obj)include/config.h ; \
+ fi ;
+ @$(MKCONFIG) -a SIMPC8313 ppc mpc83xx simpc8313 sheldon
+ @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+
TQM834x_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx tqm834x tqc
diff --git a/board/sheldon/simpc8313/Makefile b/board/sheldon/simpc8313/Makefile
new file mode 100644
index 0000000000..7c34c5e164
--- /dev/null
+++ b/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/sheldon/simpc8313/config.mk b/board/sheldon/simpc8313/config.mk
new file mode 100644
index 0000000000..ce1c0d8d93
--- /dev/null
+++ b/board/sheldon/simpc8313/config.mk
@@ -0,0 +1,13 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0x00100000
+endif
+
+ifdef CONFIG_NAND_LP
+PAD_TO = 0xFFF20000
+else
+PAD_TO = 0xFFF04000
+endif
diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c
new file mode 100644
index 0000000000..ebb70a2327
--- /dev/null
+++ b/board/sheldon/simpc8313/sdram.c
@@ -0,0 +1,193 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static long fixed_sdram(void);
+
+#if defined(CONFIG_NAND_SPL)
+void si_wait_i2c(void)
+{
+ volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+
+ while (!(__raw_readb(&im->i2c[0].sr) & 0x02))
+ ;
+
+ __raw_writeb(0x00, &im->i2c[0].sr);
+
+ sync();
+
+ return;
+}
+
+void si_read_i2c(u32 lbyte, int count, u8 *buffer)
+{
+ volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+ u32 i;
+ u8 chip = 0x50 << 1; /* boot sequencer I2C */
+ u32 ubyte = (lbyte & 0xff00) >> 8;
+
+ lbyte &= 0xff;
+
+ /*
+ * Set up controller
+ */
+ __raw_writeb(0x3f, &im->i2c[0].fdr);
+ __raw_writeb(0x00, &im->i2c[0].adr);
+ __raw_writeb(0x00, &im->i2c[0].sr);
+ __raw_writeb(0x00, &im->i2c[0].dr);
+
+ while (__raw_readb(&im->i2c[0].sr) & 0x20)
+ ;
+
+ /*
+ * Writing address to device
+ */
+ __raw_writeb(0xb0, &im->i2c[0].cr);
+ sync();
+ __raw_writeb(chip, &im->i2c[0].dr);
+ si_wait_i2c();
+
+ __raw_writeb(0xb0, &im->i2c[0].cr);
+ sync();
+ __raw_writeb(ubyte, &im->i2c[0].dr);
+ si_wait_i2c();
+
+ __raw_writeb(lbyte, &im->i2c[0].dr);
+ si_wait_i2c();
+
+ __raw_writeb(0xb4, &im->i2c[0].cr);
+ sync();
+ __raw_writeb(chip + 1, &im->i2c[0].dr);
+ si_wait_i2c();
+
+ __raw_writeb(0xa0, &im->i2c[0].cr);
+ sync();
+
+ /*
+ * Dummy read
+ */
+ __raw_readb(&im->i2c[0].dr);
+
+ si_wait_i2c();
+
+ /*
+ * Read actual data
+ */
+ for (i = 0; i < count; i++)
+ {
+ if (i == (count - 2)) /* Reached next to last byte, No ACK */
+ __raw_writeb(0xa8, &im->i2c[0].cr);
+ if (i == (count - 1)) /* Reached last byte, STOP */
+ __raw_writeb(0x88, &im->i2c[0].cr);
+
+ /* Read byte of data */
+ buffer[i] = __raw_readb(&im->i2c[0].dr);
+
+ if (i == (count - 1))
+ break;
+ si_wait_i2c();
+ }
+
+ return;
+}
+#endif /* CONFIG_NAND_SPL */
+
+phys_size_t initdram(int board_type)
+{
+ volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+ volatile fsl_lbus_t *lbc= &im->lbus;
+ u32 msize;
+
+ if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
+ return -1;
+
+ /* DDR SDRAM - Main SODIMM */
+ __raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar);
+
+ msize = fixed_sdram();
+
+ /* Local Bus setup lbcr and mrtpr */
+ __raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr);
+ __raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr);
+ sync();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return (msize * 1024 * 1024);
+}
+
+/*************************************************************************
+ * fixed sdram init -- reads values from boot sequencer I2C
+ ************************************************************************/
+static long fixed_sdram(void)
+{
+ volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+ u32 msizelog2, msize = 1;
+#if defined(CONFIG_NAND_SPL)
+ u32 i;
+ const u8 bytecount = 135;
+ u8 buffer[bytecount];
+ u32 addr, data;
+
+ si_read_i2c(0, bytecount, buffer);
+
+ for (i = 18; i < bytecount; i += 7){
+ addr = (u32)buffer[i];
+ addr <<= 8;
+ addr |= (u32)buffer[i + 1];
+ addr <<= 2;
+ data = (u32)buffer[i + 2];
+ data <<= 8;
+ data |= (u32)buffer[i + 3];
+ data <<= 8;
+ data |= (u32)buffer[i + 4];
+ data <<= 8;
+ data |= (u32)buffer[i + 5];
+
+ __raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr));
+ }
+
+ sync();
+
+ /* enable DDR controller */
+ __raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg);
+#endif /* (CONFIG_NAND_SPL) */
+
+ msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1);
+ msize <<= (msizelog2 - 20);
+
+ return msize;
+}
diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c
new file mode 100644
index 0000000000..25e5c2409d
--- /dev/null
+++ b/board/sheldon/simpc8313/simpc8313.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ puts("Board: Sheldon Instruments SIMPC8313\n");
+ return 0;
+}
+
+#ifndef CONFIG_NAND_SPL
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+ phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+ size: CONFIG_SYS_PCI1_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+ phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+ size: CONFIG_SYS_PCI1_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CONFIG_SYS_PCI1_IO_BASE,
+ phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+ size: CONFIG_SYS_PCI1_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+ int warmboot;
+
+ /* Enable all 3 PCI_CLK_OUTPUTs. */
+ clk->occr |= 0xe0000000;
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+ pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+ warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+ mpc83xx_pci_init(1, reg, warmboot);
+}
+
+/*
+ * Miscellaneous late-boot configurations
+ */
+int misc_init_r(void)
+{
+ int rc = 0;
+
+ return rc;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+}
+#endif
+#else /* CONFIG_NAND_SPL */
+void board_init_f(ulong bootflag)
+{
+ NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
+ CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
+ puts("NAND boot... ");
+ init_timebase();
+ initdram(0);
+ relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000, (gd_t *)gd,
+ CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ nand_boot();
+}
+
+void putc(char c)
+{
+ if (gd->flags & GD_FLG_SILENT)
+ return;
+
+ if (c == '\n')
+ NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
+
+ NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
+}
+#endif
diff --git a/doc/README.simpc8313 b/doc/README.simpc8313
new file mode 100644
index 0000000000..b362c6aeea
--- /dev/null
+++ b/doc/README.simpc8313
@@ -0,0 +1,80 @@
+Sheldon Instruments SIMPC8313 Board
+-----------------------------------------
+
+1. Board Switches and Jumpers
+
+ S2 is used to set CFG_RESET_SOURCE.
+
+ To boot the image in Large page NAND flash, use these DIP
+ switch settings for S2:
+
+ +----------+ ON
+ | * * **** |
+ | * * |
+ +----------+
+ 12345678
+
+ To boot the image in Small page NAND flash, use these DIP
+ switch settings for S2:
+
+ +----------+ ON
+ | *** **** |
+ | * |
+ +----------+
+ 12345678
+ (where the '*' indicates the position of the tab of the switch.)
+
+2. Memory Map
+ The memory map looks like this:
+
+ 0x0000_0000 0x1fff_ffff DDR 512M
+ 0x8000_0000 0x8fff_ffff PCI MEM 256M
+ 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
+ 0xe000_0000 0xe00f_ffff IMMR 1M
+ 0xe200_0000 0xe20f_ffff PCI IO 16M
+ 0xe280_0000 0xe280_7fff NAND FLASH (CS0) 32K
+ or
+ 0xe280_0000 0xe281_ffff NAND FLASH (CS0) 128K
+ 0xff00_0000 0xff00_7fff FPGA (CS1) 1M
+
+3. Compilation
+
+ Assuming you're using BASH (or similar) as your shell:
+
+ export CROSS_COMPILE=your-cross-compiler-prefix-
+ make distclean
+ make SIMPC8313_LP_config
+ (or make SIMPC8313_SP_config, depending on the page size
+ of your NAND flash)
+ make
+
+4. Downloading and Flashing Images
+
+4.1 Reflash U-boot Image using U-boot
+
+ =>run update_uboot
+
+ You may want to try
+ =>tftp $loadaddr $uboot
+ first, to make sure that the TFTP load will succeed before it
+ goes ahead and wipes out your current firmware. And of course,
+ if the new u-boot doesn't boot, you can plug the board into
+ your PCI slot and with the supplied driver and sample app
+ you can reburn a working u-boot.
+
+4.2 Downloading and Booting Linux Kernel
+
+ Ensure that all networking-related environment variables are set
+ properly (including ipaddr, serverip, gatewayip (if needed),
+ netmask, ethaddr, eth1addr, fdtfile, and bootfile).
+
+ =>tftp $loadaddr uImage
+ =>nand write $loadaddr kernel $filesize
+ =>tftp $loadaddr $fdtfile
+ =>nand write $loadaddr 7e0000 1800
+
+ =>boot
+
+5 Notes
+
+ The console baudrate for SIMPC8313 is 115200bps.
diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h
new file mode 100644
index 0000000000..a616236b77
--- /dev/null
+++ b/include/configs/SIMPC8313.h
@@ -0,0 +1,544 @@
+/*
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * simpc8313 board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_NAND_U_BOOT
+
+#define CONFIG_E300 1
+#define CONFIG_MPC83XX 1
+#define CONFIG_MPC831X 1
+#define CONFIG_MPC8313 1
+
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI
+
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is Marvell PHY 88E1118
+ */
+
+#define CONFIG_SYS_33MHZ
+
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR 0xE0000000
+
+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00001000
+#define CONFIG_SYS_MEMTEST_END 0x07f00000
+
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+
+/*
+ * Device configurations
+ */
+#define CONFIG_TSEC1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_MAX_MEM_MAPPED (512 << 20)
+
+#define CONFIG_SYS_DDRCDR ( DDRCDR_EN \
+ | DDRCDR_PZ_NOMZ \
+ | DDRCDR_NZ_NOMZ \
+ | DDRCDR_M_ODR )
+ /* 0x73000002 TODO ODR & DRN ? */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if !defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_EADC_1 | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
+ | (0xFF << LBCR_BMT_SHIFT) \
+ | 0xF ) /* 0x0004ff0f */
+
+#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
+
+/* drivers/mtd/nand/nand.c */
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE 0xFFF00000
+#else
+#define CONFIG_SYS_NAND_BASE 0xE2800000
+#endif
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
+#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
+
+#define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V ) /* valid */
+
+#ifdef CONFIG_NAND_SP
+#define CONFIG_SYS_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR )
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000000E /* 32KB */
+#define CONFIG_SYS_NAND_PAGE_SIZE (512) /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define NAND_CACHE_PAGES 32
+#elif defined(CONFIG_NAND_LP)
+#define CONFIG_SYS_NAND_OR_PRELIM ( 0xFFFC0000 /* length 256K */ \
+ | OR_FCM_PGS \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR )
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000011 /* 256KB */
+#define CONFIG_SYS_NAND_PAGE_SIZE (2048) /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */
+#define NAND_CACHE_PAGES 64
+#else
+#error Page size of NAND not defined.
+#endif /* CONFIG_NAND_SP */
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SYS_NAND_BLOCK_SIZE
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR0_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR0_PRELIM
+
+/*
+ * JFFS2 configuration
+ */
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_DEV "nand0"
+
+/* mtdparts command line support */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nand0=nand0"
+#define MTDPARTS_DEFAULT "mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)"
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII /* MII PHY management */
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC2_PHYIDX 0
+#endif
+
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC1"
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_NAND_U_BOOT)
+ #define CONFIG_ENV_IS_IN_NAND 1
+ #define CONFIG_ENV_OFFSET (768 * 1024)
+ #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+ #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+ #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+ #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4)
+ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
+#elif !defined(CONFIG_SYS_RAMBOOT)
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+ #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
+ #define CONFIG_ENV_SIZE 0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_JFFS2
+
+#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING 1
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE ( CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT) \
+ + 16 ) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#define CONFIG_SYS_HRCW_LOW ( HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \
+ | 0x20000000 /* reserved */ \
+ | HRCWL_DDR_TO_SCB_CLK_2X1 \
+ | HRCWL_CSB_TO_CLKIN_4X1 \
+ | HRCWL_CORE_TO_CSB_2_5X1 )
+
+#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 4)
+
+#define CONFIG_SYS_HRCW_HIGH_BASE ( HRCWH_PCI_HOST \
+ | HRCWH_PCI1_ARBITER_ENABLE \
+ | HRCWH_CORE_ENABLE \
+ | HRCWH_BOOTSEQ_DISABLE \
+ | HRCWH_SW_WATCHDOG_DISABLE \
+ | HRCWH_TSEC1M_IN_RGMII \
+ | HRCWH_TSEC2M_IN_RGMII \
+ | HRCWH_BIG_ENDIAN \
+ | HRCWH_LALE_NORMAL )
+
+#ifdef CONFIG_NAND_LP
+#define CONFIG_SYS_HRCW_HIGH ( CONFIG_SYS_HRCW_HIGH_BASE \
+ | HRCWH_FROM_0XFFF00100 \
+ | HRCWH_ROM_LOC_NAND_LP_8BIT \
+ | HRCWH_RL_EXT_NAND)
+#else
+#define CONFIG_SYS_HRCW_HIGH ( CONFIG_SYS_HRCW_HIGH_BASE \
+ | HRCWH_FROM_0XFFF00100 \
+ | HRCWH_ROM_LOC_NAND_SP_8BIT \
+ | HRCWH_RL_EXT_NAND )
+#endif
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH ( SICRH_ETSEC2_B \
+ | SICRH_ETSEC2_C \
+ | SICRH_ETSEC2_D \
+ | SICRH_ETSEC2_E \
+ | SICRH_ETSEC2_F \
+ | SICRH_ETSEC2_G \
+ | SICRH_TSOBI1 \
+ | SICRH_TSOBI2 )
+#define CONFIG_SYS_SICRL (SICRL_USBDR \
+ | SICRL_ETSEC2_A )
+
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
+ | HID0_ENABLE_DYNAMIC_POWER_MANAGMENT )
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L ((CONFIG_SYS_SDRAM_BASE + 0x10000000) | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U ((CONFIG_SYS_SDRAM_BASE + 0x10000000) | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10)
+#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NETDEV eth1
+
+#define CONFIG_HOSTNAME simpc8313
+#define CONFIG_ROOTPATH /tftpboot/
+#define CONFIG_BOOTFILE /tftpboot/uImage
+#define CONFIG_UBOOTPATH u-boot-nand.bin /* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE simpc8313.dtb
+
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY 5 /* 5 second delay */
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_BOOTCOMMAND "nand read $loadaddr kernel 600000;bootm $loadaddr - $fdtaddr"
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "ethprime=TSEC1\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "fdtaddr=ae0000\0" \
+ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
+ "console=ttyS0\0" \
+ "setbootargs=setenv bootargs " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+ "load_uboot=tftp 100000 u-boot-nand.bin\0" \
+ "burn_uboot=nand erase u-boot 80000; " \
+ "nand write 100000 u-boot $filesize\0" \
+ "update_uboot=run load_uboot;run burn_uboot\0" \
+ "mtdids=nand0=nand0\0" \
+ "mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+ "bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw " \
+ "console=ttyS0,115200\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv rootdev /dev/ram;" \
+ "run setbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif /* __CONFIG_H */
diff --git a/nand_spl/board/sheldon/simpc8313/Makefile b/nand_spl/board/sheldon/simpc8313/Makefile
new file mode 100644
index 0000000000..b0967a30b1
--- /dev/null
+++ b/nand_spl/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,100 @@
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+# (C) Copyright 2008 Freescale Semiconductor
+# (C) Copyright Sheldon Instruments, Inc. 2008
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+NAND_SPL := y
+TEXT_BASE := 0xfff00000
+
+include $(TOPDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS += -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_NAND_SPL
+
+SOBJS = start.o ticks.o
+COBJS = nand_boot_fsl_elbc.o $(BOARD).o sdram.o ns16550.o nand_init.o time.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj := $(OBJTREE)/nand_spl/
+
+ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all: $(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: $(OBJS)
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+ -Map $(nandobj)u-boot-spl.map \
+ -o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+$(obj)start.S:
+ ln -sf $(SRCTREE)/cpu/mpc83xx/start.S $<
+
+$(obj)nand_boot_fsl_elbc.c:
+ ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c $<
+
+$(obj)sdram.c:
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/sdram.c $<
+
+$(obj)$(BOARD).c:
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/$(BOARD).c $<
+
+$(obj)ns16550.c:
+ ln -sf $(SRCTREE)/drivers/serial/ns16550.c $<
+
+$(obj)nand_init.c:
+ ln -sf $(SRCTREE)/cpu/mpc83xx/nand_init.c $<
+
+$(obj)time.c:
+ ln -sf $(SRCTREE)/lib_ppc/time.c $<
+
+$(obj)ticks.S:
+ ln -sf $(SRCTREE)/lib_ppc/ticks.S $<
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)%.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/sheldon/simpc8313/u-boot.lds b/nand_spl/board/sheldon/simpc8313/u-boot.lds
new file mode 100644
index 0000000000..40c414549c
--- /dev/null
+++ b/nand_spl/board/sheldon/simpc8313/u-boot.lds
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+ . = 0xfff00000;
+ .text : {
+ *(.text*)
+ . = ALIGN(16);
+ *(.rodata*)
+ *(.eh_frame)
+ }
+
+ . = ALIGN(8);
+ .data : {
+ *(.data*)
+ *(.sdata*)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ __got2_entries = (. - _GOT2_TABLE_) >> 2;
+ }
+
+ . = ALIGN(8);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.*bss) }
+ _end = .;
+}
+ENTRY(_start)
+ASSERT(_end <= 0xfff01000, "NAND bootstrap too big");