Initial revision

38 files changed, 10205 insertions, 0 deletions

diff --git a/board/hymod/global_env b/board/hymod/global_env
new file mode 100644
index 00000000000..913f82db08a
--- /dev/null
+++ b/board/hymod/global_env
@@ -0,0 +1,69 @@
+# format of this file is:
+#
+#	1. blank lines and lines beginning with '#' are ignored
+#	2. all other lines must have the form <name>=<value>
+#	3. if a percent appears anywhere, it is replaced like so:
+#
+#		%s	serial number of the main board (10 digit zero filled)
+#		%S	serial number of the main board (plain number)
+#		%%	a percentage character
+#
+# no whitespace is removed in either <name> or <value>
+#
+# if first character in <name> is a dash ('-'), then an existing env var
+# will not be overwritten (the dash is removed).
+#
+# if last character in <name> is a plus ('+'), then <value> will be appended
+# to any existing env var (the plus is removed). Duplicates of <value> are
+# removed.
+#
+
+# set the ip address based on the main board serial number
+ipaddr=192.168.1.%S
+serverip=192.168.1.254
+
+# stop auto execute after tftp
+autostart=no
+
+#
+# 16M flash map, 64 x 256K sectors, mapped at address 0x40000000
+#
+# sector 0:	boot
+# sector 1:	non volatile environment
+# sectors 2-4:	linux kernel image
+# sectors 5-7:	alternate linux kernel image
+# sectors 8-63:	linux initial ramdisk image
+#
+
+fetchboot=tftp 100000 /hymod/u-boot.bin
+eraseboot=protect off 1:0 ; erase 1:0 ; protect on 1:0
+copyboot=protect off 1:0 ; cp.b 100000 40000000 40000 ; protect on 1:0
+cmpboot=cmp.b 100000 40000000 40000
+newboot=run fetchboot eraseboot copyboot cmpboot
+
+fetchlinux=tftp 100000 /hymod/linux.bin
+eraselinux=erase 1:2-4
+copylinux=cp.b 100000 40080000 $(filesize)
+cmplinux=cmp.b 100000 40080000 $(filesize)
+newlinux=run fetchlinux eraselinux copylinux cmplinux
+
+fetchaltlinux=tftp 100000 /hymod/altlinux.bin
+erasealtlinux=erase 1:5-7
+copyaltlinux=cp.b 100000 40080000 $(filesize)
+cmpaltlinux=cmp.b 100000 40080000 $(filesize)
+newaltlinux=run fetchaltlinux erasealtlinux copyaltlinux cmpaltlinux
+
+fetchird=tftp 100000 /hymod/initrd.bin
+eraseird=erase 1:8-63
+copyird=cp.b 100000 40200000 $(filesize)
+cmpird=cmp.b 100000 40200000 $(filesize)
+newinitrd=run fetchird eraseird copyird cmpird
+
+bootcmd=bootm 40080000 40200000
+-bootargs=root=/dev/ram rw
+# these are for hymod linux
+bootargs+=preload=unix,i2c-cpm,i2c-dev
+bootargs+=serialno=%S
+bootargs+=ramdisk_size=32768
+bootargs+=automount nisclient nisdomain=mlb.dmt.csiro.au nissrvadr=138.194.112.4
+bootdelay=2
diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c
new file mode 100644
index 00000000000..e797b362814
--- /dev/null
+++ b/board/lwmon/lwmon.c
@@ -0,0 +1,966 @@
+/***********************************************************************
+ *
+M* Modul:         lwmon.c
+M*
+M* Content:       LWMON specific U-Boot commands.
+ *
+ * (C) Copyright 2001, 2002
+ * DENX Software Engineering
+ * Wolfgang Denk, wd@denx.de
+ * All rights reserved.
+ *
+D* Design:        wd@denx.de
+C* Coding:        wd@denx.de
+V* Verification:  dzu@denx.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ ***********************************************************************/
+
+/*---------------------------- Headerfiles ----------------------------*/
+#include <common.h>
+#include <mpc8xx.h>
+#include <commproc.h>
+#include <i2c.h>
+#include <command.h>
+#include <cmd_bsp.h>
+#include <malloc.h>
+#include <post.h>
+
+#include <linux/types.h>
+#include <linux/string.h>	/* for strdup */
+
+/*------------------------ Local prototypes ---------------------------*/
+static long int dram_size (long int, long int *, long int);
+
+
+/*--------------------- Local macros and constants --------------------*/
+#define	_NOT_USED_	0xFFFFFFFF
+
+/*
+ * 66 MHz SDRAM access using UPM A
+ */
+const uint sdram_table[] =
+{
+#if defined(CFG_MEMORY_75) || defined(CFG_MEMORY_8E)
+	/*
+	 * Single Read. (Offset 0 in UPM RAM)
+	 */
+	0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00,
+	0x1FF5FC47, /* last */
+	/*
+	 * SDRAM Initialization (offset 5 in UPM RAM)
+	 *
+         * This is no UPM entry point. The following definition uses
+         * the remaining space to establish an initialization
+         * sequence, which is executed by a RUN command.
+	 *
+	 */
+		    0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
+	/*
+	 * Burst Read. (Offset 8 in UPM RAM)
+	 */
+	0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
+	0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Single Write. (Offset 18 in UPM RAM)
+	 */
+	0x1F2DFC04, 0xEEABBC00, 0x01B27C04, 0x1FF5FC47, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Write. (Offset 20 in UPM RAM)
+	 */
+	0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
+	0xF0AFFC00, 0xE1BAFC04, 0x01FF5FC47, /* last */
+					    _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Refresh  (Offset 30 in UPM RAM)
+	 */
+	0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+	0xFFFFFC84, 0xFFFFFC07, /* last */
+				_NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Exception. (Offset 3c in UPM RAM)
+	 */
+	0x7FFFFC07, /* last */
+		    0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF,
+#endif
+#ifdef CFG_MEMORY_7E
+	/*
+	 * Single Read. (Offset 0 in UPM RAM)
+	 */
+	0x0E2DBC04, 0x11AF7C04, 0xEFBAFC00, 0x1FF5FC47, /* last */
+	_NOT_USED_,
+	/*
+	 * SDRAM Initialization (offset 5 in UPM RAM)
+	 *
+         * This is no UPM entry point. The following definition uses
+         * the remaining space to establish an initialization
+         * sequence, which is executed by a RUN command.
+	 *
+	 */
+		    0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
+	/*
+	 * Burst Read. (Offset 8 in UPM RAM)
+	 */
+	0x0E2DBC04, 0x10AF7C04, 0xF0AFFC00, 0xF0AFFC00,
+	0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
+				 	    _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Single Write. (Offset 18 in UPM RAM)
+	 */
+	0x0E29BC04, 0x01B27C04, 0x1FF5FC47, /* last */
+					    _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Write. (Offset 20 in UPM RAM)
+	 */
+	0x0E29BC04, 0x10A77C00, 0xF0AFFC00, 0xF0AFFC00,
+	0xE1BAFC04, 0x1FF5FC47, /* last */
+			        _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Refresh  (Offset 30 in UPM RAM)
+	 */
+	0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+	0xFFFFFC84, 0xFFFFFC07, /* last */
+				_NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Exception. (Offset 3c in UPM RAM)
+	 */
+	0x7FFFFC07, /* last */
+		    0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF,
+#endif
+};
+
+/*
+ * Check Board Identity:
+ *
+ */
+
+/***********************************************************************
+F* Function:     int checkboard (void) P*A*Z*
+ *
+P* Parameters:   none
+P*
+P* Returnvalue:  int - 0 is always returned
+ *
+Z* Intention:    This function is the checkboard() method implementation
+Z*               for the lwmon board.  Only a standard message is printed.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int checkboard (void)
+{
+	puts ("Board: Litronic Monitor IV\n");
+	return (0);
+}
+
+/***********************************************************************
+F* Function:     long int initdram (int board_type) P*A*Z*
+ *
+P* Parameters:   int board_type
+P*                - Usually type of the board - ignored here.
+P*
+P* Returnvalue:  long int
+P*                - Size of initialized memory
+ *
+Z* Intention:    This function is the initdram() method implementation
+Z*               for the lwmon board.
+Z*               The memory controller is initialized to access the
+Z*               DRAM.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+long int initdram (int board_type)
+{
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immr->im_memctl;
+	long int size_b0;
+	long int size8, size9;
+	int i;
+
+	/*
+	 * Configure UPMA for SDRAM
+	 */
+	upmconfig (UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
+
+	memctl->memc_mptpr = CFG_MPTPR;
+
+	/* burst length=4, burst type=sequential, CAS latency=2 */
+	memctl->memc_mar = CFG_MAR;
+
+	/*
+	 * Map controller bank 3 to the SDRAM bank at preliminary address.
+	 */
+	memctl->memc_or3 = CFG_OR3_PRELIM;
+	memctl->memc_br3 = CFG_BR3_PRELIM;
+
+	/* initialize memory address register */
+	memctl->memc_mamr = CFG_MAMR_8COL;	/* refresh not enabled yet */
+
+	/* mode initialization (offset 5) */
+	udelay (200);				/* 0x80006105 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x05);
+
+	/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
+	udelay (1);				/* 0x80006130 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30);
+	udelay (1);				/* 0x80006130 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30);
+
+	udelay (1);				/* 0x80006106 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x06);
+
+	memctl->memc_mamr |= MAMR_PTBE;	/* refresh enabled */
+
+	udelay (200);
+
+	/* Need at least 10 DRAM accesses to stabilize */
+	for (i = 0; i < 10; ++i) {
+		volatile unsigned long *addr =
+			(volatile unsigned long *) SDRAM_BASE3_PRELIM;
+		unsigned long val;
+
+		val = *(addr + i);
+		*(addr + i) = val;
+	}
+
+	/*
+	 * Check Bank 0 Memory Size for re-configuration
+	 *
+	 * try 8 column mode
+	 */
+	size8 = dram_size (CFG_MAMR_8COL, (ulong *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
+
+	udelay (1000);
+
+	/*
+	 * try 9 column mode
+	 */
+	size9 = dram_size (CFG_MAMR_9COL, (ulong *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
+
+	if (size8 < size9) {		/* leave configuration at 9 columns */
+		size_b0 = size9;
+		memctl->memc_mamr = CFG_MAMR_9COL | MAMR_PTBE;
+		udelay (500);
+	} else {			/* back to 8 columns            */
+		size_b0 = size8;
+		memctl->memc_mamr = CFG_MAMR_8COL | MAMR_PTBE;
+		udelay (500);
+	}
+
+	/*
+	 * Final mapping:
+	 */
+
+	memctl->memc_or3 = ((-size_b0) & 0xFFFF0000) |
+			OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
+	memctl->memc_br3 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+	udelay (1000);
+
+	return (size_b0);
+}
+
+/***********************************************************************
+F* Function:     static long int dram_size (long int mamr_value,
+F*                                          long int *base,
+F*                                          long int maxsize) P*A*Z*
+ *
+P* Parameters:   long int mamr_value
+P*                - Value for MAMR for the test
+P*               long int *base
+P*                - Base address for the test
+P*               long int maxsize
+P*                - Maximum size to test for
+P*
+P* Returnvalue:  long int
+P*                - Size of probed memory
+ *
+Z* Intention:    Check memory range for valid RAM. A simple memory test
+Z*               determines the actually available RAM size between
+Z*               addresses `base' and `base + maxsize'. Some (not all)
+Z*               hardware errors are detected:
+Z*                - short between address lines
+Z*                - short between data lines
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+static long int dram_size (long int mamr_value, long int *base, long int maxsize)
+{
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immr->im_memctl;
+	volatile long int *addr;
+	ulong cnt, val;
+	ulong save[32];				/* to make test non-destructive */
+	unsigned char i = 0;
+
+	memctl->memc_mamr = mamr_value;
+
+	for (cnt = maxsize / sizeof (long); cnt > 0; cnt >>= 1) {
+		addr = base + cnt;		/* pointer arith! */
+
+		save[i++] = *addr;
+		*addr = ~cnt;
+	}
+
+	/* write 0 to base address */
+	addr = base;
+	save[i] = *addr;
+	*addr = 0;
+
+	/* check at base address */
+	if ((val = *addr) != 0) {
+		*addr = save[i];
+		return (0);
+	}
+
+	for (cnt = 1; cnt <= maxsize / sizeof (long); cnt <<= 1) {
+		addr = base + cnt;		/* pointer arith! */
+
+		val = *addr;
+		*addr = save[--i];
+
+		if (val != (~cnt)) {
+			return (cnt * sizeof (long));
+		}
+	}
+	return (maxsize);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#ifndef	PB_ENET_TENA
+# define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+#endif
+
+/***********************************************************************
+F* Function:     int board_pre_init (void) P*A*Z*
+ *
+P* Parameters:   none
+P*
+P* Returnvalue:  int
+P*                - 0 is always returned.
+ *
+Z* Intention:    This function is the board_pre_init() method implementation
+Z*               for the lwmon board.
+Z*               Disable Ethernet TENA on Port B.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int board_pre_init (void)
+{
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+
+	/* Disable Ethernet TENA on Port B
+	 * Necessary because of pull up in COM3 port.
+	 *
+	 * This is just a preliminary fix, intended to turn off TENA
+	 * as soon as possible to avoid noise on the network. Once
+	 * I²C is running we will make sure the interface is
+	 * correctly initialized.
+	 */
+	immr->im_cpm.cp_pbpar &= ~PB_ENET_TENA;
+	immr->im_cpm.cp_pbodr &= ~PB_ENET_TENA;
+	immr->im_cpm.cp_pbdat &= ~PB_ENET_TENA;	/* set to 0 = disabled */
+	immr->im_cpm.cp_pbdir |= PB_ENET_TENA;
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/***********************************************************************
+F* Function:     void reset_phy (void) P*A*Z*
+ *
+P* Parameters:   none
+P*
+P* Returnvalue:  none
+ *
+Z* Intention:    Reset the PHY.  In the lwmon case we do this by the
+Z*               signaling the PIC I/O expander.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+void reset_phy (void)
+{
+	uchar c;
+
+#ifdef DEBUG
+	printf ("### Switch on Ethernet for SCC2 ###\n");
+#endif
+	c = pic_read (0x61);
+#ifdef DEBUG
+	printf ("Old PIC read: reg_61 = 0x%02x\n", c);
+#endif
+	c |= 0x40;					/* disable COM3 */
+	c &= ~0x80;					/* enable Ethernet */
+	pic_write (0x61, c);
+#ifdef DEBUG
+	c = pic_read (0x61);
+	printf ("New PIC read: reg_61 = 0x%02x\n", c);
+#endif
+	udelay (1000);
+}
+
+
+/*------------------------- Keyboard controller -----------------------*/
+/* command codes */
+#define	KEYBD_CMD_READ_KEYS	0x01
+#define KEYBD_CMD_READ_VERSION	0x02
+#define KEYBD_CMD_READ_STATUS	0x03
+#define KEYBD_CMD_RESET_ERRORS	0x10
+
+/* status codes */
+#define KEYBD_STATUS_MASK	0x3F
+#define	KEYBD_STATUS_H_RESET	0x20
+#define KEYBD_STATUS_BROWNOUT	0x10
+#define KEYBD_STATUS_WD_RESET	0x08
+#define KEYBD_STATUS_OVERLOAD	0x04
+#define KEYBD_STATUS_ILLEGAL_WR	0x02
+#define KEYBD_STATUS_ILLEGAL_RD	0x01
+
+/* Number of bytes returned from Keyboard Controller */
+#define KEYBD_VERSIONLEN	2	/* version information */
+#define	KEYBD_DATALEN		9	/* normal key scan data */
+
+/* maximum number of "magic" key codes that can be assigned */
+
+static uchar kbd_addr = CFG_I2C_KEYBD_ADDR;
+
+static uchar *key_match (uchar *);
+
+#define	KEYBD_SET_DEBUGMODE	'#'	/* Magic key to enable debug output */
+
+/***********************************************************************
+F* Function:     int misc_init_r (void) P*A*Z*
+ *
+P* Parameters:   none
+P*
+P* Returnvalue:  int
+P*                - 0 is always returned, even in the case of a keyboard
+P*                    error.
+ *
+Z* Intention:    This function is the misc_init_r() method implementation
+Z*               for the lwmon board.
+Z*               The keyboard controller is initialized and the result
+Z*               of a read copied to the environment variable "keybd".
+Z*               If KEYBD_SET_DEBUGMODE is defined, a check is made for
+Z*               this key, and if found display to the LCD will be enabled.
+Z*               The keys in "keybd" are checked against the magic
+Z*               keycommands defined in the environment.
+Z*               See also key_match().
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int misc_init_r (void)
+{
+	uchar kbd_data[KEYBD_DATALEN];
+	uchar tmp_data[KEYBD_DATALEN];
+	uchar keybd_env[2 * KEYBD_DATALEN + 1];
+	uchar val, errcd;
+	uchar *str;
+	int i;
+
+	i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+	/* Read initial keyboard error code */
+	val = KEYBD_CMD_READ_STATUS;
+	i2c_write (kbd_addr, 0, 0, &val, 1);
+	i2c_read (kbd_addr, 0, 0, &errcd, 1);
+	/* clear unused bits */
+	errcd &= KEYBD_STATUS_MASK;
+	/* clear "irrelevant" bits. Recommended by Martin Rajek, LWN */
+	errcd &= ~(KEYBD_STATUS_H_RESET|KEYBD_STATUS_BROWNOUT);
+	if (errcd) {
+		printf ("KEYBD: Error %02X\n", errcd);
+	}
+	/* Reset error code and verify */
+	val = KEYBD_CMD_RESET_ERRORS;
+	i2c_write (kbd_addr, 0, 0, &val, 1);
+	udelay(1000);	/* delay NEEDED by keyboard PIC !!! */
+
+	val = KEYBD_CMD_READ_STATUS;
+	i2c_write (kbd_addr, 0, 0, &val, 1);
+	i2c_read (kbd_addr, 0, 0, &val, 1);
+
+	val &= KEYBD_STATUS_MASK;	/* clear unused bits */
+	if (val) {			/* permanent error, report it */
+		printf ("*** Keyboard error code %02X ***\n", val);
+		sprintf (keybd_env, "%02X", val);
+		setenv ("keybd", keybd_env);
+		return 0;
+	}
+
+	/*
+	 * Now we know that we have a working  keyboard,  so  disable
+	 * all output to the LCD except when a key press is detected.
+	 */
+
+	if ((console_assign (stdout, "serial") < 0) ||
+		(console_assign (stderr, "serial") < 0)) {
+		printf ("Can't assign serial port as output device\n");
+	}
+
+	/* Read Version */
+	val = KEYBD_CMD_READ_VERSION;
+	i2c_write (kbd_addr, 0, 0, &val, 1);
+	i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_VERSIONLEN);
+	printf ("KEYBD: Version %d.%d\n", kbd_data[0], kbd_data[1]);
+
+	/*
+	 * Read current keyboard state.
+	 *
+         * After the error reset it may take some time before the
+         * keyboard PIC picks up a valid keyboard scan - the total
+         * scan time is approx. 1.6 ms (information by Martin Rajek,
+         * 28 Sep 2002). We read a couple of times for the keyboard
+         * to stabilize, using a big enough delay.
+         * 10 times should be enough. If the data is still changing,
+         * we use what we get :-(
+	 */
+
+	memset (tmp_data, 0xFF, KEYBD_DATALEN);	/* impossible value */
+	for (i=0; i<10; ++i) {
+		val = KEYBD_CMD_READ_KEYS;
+		i2c_write (kbd_addr, 0, 0, &val, 1);
+		i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
+
+		if (memcmp(kbd_data, tmp_data, KEYBD_DATALEN) == 0) {
+			/* consistent state, done */
+			break;
+		}
+		/* remeber last state, delay, and retry */
+		memcpy (tmp_data, kbd_data, KEYBD_DATALEN);
+		udelay (5000);
+	}
+
+	for (i = 0; i < KEYBD_DATALEN; ++i) {
+		sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
+	}
+	setenv ("keybd", keybd_env);
+
+	str = strdup (key_match (kbd_data));	/* decode keys */
+#ifdef KEYBD_SET_DEBUGMODE
+	if (kbd_data[0] == KEYBD_SET_DEBUGMODE) {	/* set debug mode */
+		if ((console_assign (stdout, "lcd") < 0) ||
+			(console_assign (stderr, "lcd") < 0)) {
+			printf ("Can't assign LCD display as output device\n");
+		}
+	}
+#endif /* KEYBD_SET_DEBUGMODE */
+#ifdef CONFIG_PREBOOT	/* automatically configure "preboot" command on key match */
+	setenv ("preboot", str);	/* set or delete definition */
+#endif /* CONFIG_PREBOOT */
+	if (str != NULL) {
+		free (str);
+	}
+	return (0);
+}
+
+#ifdef CONFIG_PREBOOT
+
+static uchar kbd_magic_prefix[] = "key_magic";
+static uchar kbd_command_prefix[] = "key_cmd";
+
+/***********************************************************************
+F* Function:     static uchar *key_match (uchar *kbd_data) P*A*Z*
+ *
+P* Parameters:   uchar *kbd_data
+P*                - The keys to match against our magic definitions
+P*
+P* Returnvalue:  uchar *
+P*                - != NULL: Pointer to the corresponding command(s)
+P*                     NULL: No magic is about to happen
+ *
+Z* Intention:    Check if pressed key(s) match magic sequence,
+Z*               and return the command string associated with that key(s).
+Z*
+Z*               If no key press was decoded, NULL is returned.
+Z*
+Z*               Note: the first character of the argument will be
+Z*                     overwritten with the "magic charcter code" of the
+Z*                     decoded key(s), or '\0'.
+Z*
+Z*               Note: the string points to static environment data
+Z*                     and must be saved before you call any function that
+Z*                     modifies the environment.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+static uchar *key_match (uchar *kbd_data)
+{
+	uchar compare[KEYBD_DATALEN-1];
+	uchar magic[sizeof (kbd_magic_prefix) + 1];
+	uchar extra;
+	uchar *str, *nxt, *suffix;
+	uchar *kbd_magic_keys;
+	int i;
+
+	/*
+	 * The following string defines the characters that can pe appended
+	 * to "key_magic" to form the names of environment variables that
+	 * hold "magic" key codes, i. e. such key codes that can cause
+	 * pre-boot actions. If the string is empty (""), then only
+	 * "key_magic" is checked (old behaviour); the string "125" causes
+	 * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
+	 */
+	if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
+		kbd_magic_keys = "";
+
+	/* loop over all magic keys;
+	 * use '\0' suffix in case of empty string
+	 */
+	for (suffix=kbd_magic_keys; *suffix || suffix==kbd_magic_keys; ++suffix) {
+		sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
+#if 0
+		printf ("### Check magic \"%s\"\n", magic);
+#endif
+		/* Don't include modifier byte */
+		memcpy (compare, kbd_data+1, KEYBD_DATALEN-1);
+
+		extra = 0;
+
+		for (str= getenv(magic); str != NULL; str = (*nxt) ? nxt+1 : nxt) {
+			uchar c;
+			int k;
+
+			c = (uchar) simple_strtoul (str, (char **) (&nxt), 16);
+
+			if (str == nxt) {	/* invalid character */
+				break;
+			}
+
+			/*
+			 * Check if this key matches the input.
+			 * Set matches to zero, so they match only once
+			 * and we can find duplicates or extra keys
+			 */
+			for (k = 0; k < sizeof(compare); ++k) {
+				if (compare[k] == '\0')	/* only non-zero entries */
+					continue;
+				if (c == compare[k]) {	/* found matching key */
+					compare[k] = '\0';
+					break;
+				}
+			}
+			if (k == sizeof(compare)) {
+				extra = 1;		/* unmatched key */
+			}
+		}
+
+		/*
+		 * A full match leaves no keys in the `compare' array,
+		 * and has no extra keys
+		 */
+
+		for (i = 0; i < sizeof(compare); ++i) {
+			if (compare[i])
+				break;
+		}
+
+		if ((i == sizeof(compare)) && (extra == 0)) {
+			uchar cmd_name[sizeof (kbd_command_prefix) + 1];
+			char *cmd;
+
+			sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
+
+			cmd = getenv (cmd_name);
+#if 0
+			printf ("### Set PREBOOT to $(%s): \"%s\"\n",
+					cmd_name, cmd ? cmd : "<<NULL>>");
+#endif
+			*kbd_data = *suffix;
+			return (cmd);
+		}
+	}
+#if 0
+	printf ("### Delete PREBOOT\n");
+#endif
+	*kbd_data = '\0';
+	return (NULL);
+}
+#endif /* CONFIG_PREBOOT */
+
+/*---------------Board Special Commands: PIC read/write ---------------*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+/***********************************************************************
+F* Function:     int do_pic (cmd_tbl_t *cmdtp, int flag,
+F*                           int argc, char *argv[]) P*A*Z*
+ *
+P* Parameters:   cmd_tbl_t *cmdtp
+P*                - Pointer to our command table entry
+P*               int flag
+P*                - If the CMD_FLAG_REPEAT bit is set, then this call is
+P*                  a repetition
+P*               int argc
+P*                - Argument count
+P*               char *argv[]
+P*                - Array of the actual arguments
+P*
+P* Returnvalue:  int
+P*                - 0  The command was handled successfully
+P*                  1  An error occurred
+ *
+Z* Intention:    Implement the "pic [read|write]" commands.
+Z*               The read subcommand takes one argument, the register,
+Z*               whereas the write command takes two, the register and
+Z*               the new value.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int do_pic (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	uchar reg, val;
+
+	switch (argc) {
+	case 3:					/* PIC read reg */
+		if (strcmp (argv[1], "read") != 0)
+			break;
+
+		reg = simple_strtoul (argv[2], NULL, 16);
+
+		printf ("PIC read: reg %02x: %02x\n\n", reg, pic_read (reg));
+
+		return 0;
+	case 4:					/* PIC write reg val */
+		if (strcmp (argv[1], "write") != 0)
+			break;
+
+		reg = simple_strtoul (argv[2], NULL, 16);
+		val = simple_strtoul (argv[3], NULL, 16);
+
+		printf ("PIC write: reg %02x val 0x%02x: %02x => ",
+				reg, val, pic_read (reg));
+		pic_write (reg, val);
+		printf ("%02x\n\n", pic_read (reg));
+		return 0;
+	default:
+		break;
+	}
+	printf ("Usage:\n%s\n", cmdtp->usage);
+	return 1;
+}
+
+/***********************************************************************
+F* Function:     int do_kbd (cmd_tbl_t *cmdtp, int flag,
+F*                           int argc, char *argv[]) P*A*Z*
+ *
+P* Parameters:   cmd_tbl_t *cmdtp
+P*                - Pointer to our command table entry
+P*               int flag
+P*                - If the CMD_FLAG_REPEAT bit is set, then this call is
+P*                  a repetition
+P*               int argc
+P*                - Argument count
+P*               char *argv[]
+P*                - Array of the actual arguments
+P*
+P* Returnvalue:  int
+P*                - 0 is always returned.
+ *
+Z* Intention:    Implement the "kbd" command.
+Z*               The keyboard status is read.  The result is printed on
+Z*               the console and written into the "keybd" environment
+Z*               variable.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	uchar kbd_data[KEYBD_DATALEN];
+	uchar keybd_env[2 * KEYBD_DATALEN + 1];
+	uchar val;
+	int i;
+
+	i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+	/* Read keys */
+	val = KEYBD_CMD_READ_KEYS;
+	i2c_write (kbd_addr, 0, 0, &val, 1);
+	i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
+
+	puts ("Keys:");
+	for (i = 0; i < KEYBD_DATALEN; ++i) {
+		sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
+		printf (" %02x", kbd_data[i]);
+	}
+	putc ('\n');
+	setenv ("keybd", keybd_env);
+	return 0;
+}
+
+/* Read and set LSB switch */
+#define CFG_PC_TXD1_ENA		0x0008
+
+/***********************************************************************
+F* Function:     int do_lsb (cmd_tbl_t *cmdtp, int flag,
+F*                           int argc, char *argv[]) P*A*Z*
+ *
+P* Parameters:   cmd_tbl_t *cmdtp
+P*                - Pointer to our command table entry
+P*               int flag
+P*                - If the CMD_FLAG_REPEAT bit is set, then this call is
+P*                  a repetition
+P*               int argc
+P*                - Argument count
+P*               char *argv[]
+P*                - Array of the actual arguments
+P*
+P* Returnvalue:  int
+P*                - 0  The command was handled successfully
+P*                  1  An error occurred
+ *
+Z* Intention:    Implement the "lsb [on|off]" commands.
+Z*               The lsb is switched according to the first parameter by
+Z*               by signaling the PIC I/O expander.
+Z*               Called with no arguments, the current setting is
+Z*               printed.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+int do_lsb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	uchar val;
+	immap_t *immr = (immap_t *) CFG_IMMR;
+
+	switch (argc) {
+	case 1:					/* lsb - print setting */
+		val = pic_read (0x60);
+		printf ("LSB is o%s\n", (val & 0x20) ? "n" : "ff");
+		return 0;
+	case 2:					/* lsb on or lsb off - set switch */
+		val = pic_read (0x60);
+
+		if (strcmp (argv[1], "on") == 0) {
+			val |= 0x20;
+			immr->im_ioport.iop_pcpar &= ~(CFG_PC_TXD1_ENA);
+			immr->im_ioport.iop_pcdat |= CFG_PC_TXD1_ENA;
+			immr->im_ioport.iop_pcdir |= CFG_PC_TXD1_ENA;
+		} else if (strcmp (argv[1], "off") == 0) {
+			val &= ~0x20;
+			immr->im_ioport.iop_pcpar &= ~(CFG_PC_TXD1_ENA);
+			immr->im_ioport.iop_pcdat &= ~(CFG_PC_TXD1_ENA);
+			immr->im_ioport.iop_pcdir |= CFG_PC_TXD1_ENA;
+		} else {
+			break;
+		}
+		pic_write (0x60, val);
+		return 0;
+	default:
+		break;
+	}
+	printf ("Usage:\n%s\n", cmdtp->usage);
+	return 1;
+}
+
+#endif /* CFG_CMD_BSP */
+
+/*----------------------------- Utilities -----------------------------*/
+/***********************************************************************
+F* Function:     uchar pic_read (uchar reg) P*A*Z*
+ *
+P* Parameters:   uchar reg
+P*                - Register to read
+P*
+P* Returnvalue:  uchar
+P*                - Value read from register
+ *
+Z* Intention:    Read a register from the PIC I/O expander.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+uchar pic_read (uchar reg)
+{
+	return (i2c_reg_read (CFG_I2C_PICIO_ADDR, reg));
+}
+
+/***********************************************************************
+F* Function:     void pic_write (uchar reg, uchar val) P*A*Z*
+ *
+P* Parameters:   uchar reg
+P*                - Register to read
+P*               uchar val
+P*                - Value to write
+P*
+P* Returnvalue:  none
+ *
+Z* Intention:    Write to a register on the PIC I/O expander.
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+void pic_write (uchar reg, uchar val)
+{
+	i2c_reg_write (CFG_I2C_PICIO_ADDR, reg, val);
+}
+
+/*---------------------- Board Control Functions ----------------------*/
+/***********************************************************************
+F* Function:     void board_poweroff (void) P*A*Z*
+ *
+P* Parameters:   none
+P*
+P* Returnvalue:  none
+ *
+Z* Intention:    Turn off the battery power and loop endless, so this
+Z*               should better be the last function you call...
+ *
+D* Design:       wd@denx.de
+C* Coding:       wd@denx.de
+V* Verification: dzu@denx.de
+ ***********************************************************************/
+void board_poweroff (void)
+{
+    /* Turn battery off */
+    ((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat &= ~(1 << (31 - 13));
+
+    while (1);
+}
diff --git a/board/musenki/README b/board/musenki/README
new file mode 100644
index 00000000000..4a1955dc38d
--- /dev/null
+++ b/board/musenki/README
@@ -0,0 +1,301 @@
+U-Boot for a Musenki M-3/M-1 board
+---------------------------
+
+Musenki M-1 and M-3 have two banks of flash of 4MB or 8MB each.
+
+In board's notation, bank 0 is the one at the address of 0xFF800000
+and bank 1 is the one at the address of 0xFF000000.
+
+On power-up the processor jumps to the address of 0xFFF00100, the last
+megabyte of the bank 0 of flash.
+
+Thus, U-Boot is configured to reside in flash starting at the address of
+0xFFF00000.  The environment space is located in flash separately from
+U-Boot, at the address of 0xFF800000.
+
+There is a Davicom 9102A on-board, but I don't have it working yet.
+
+U-Boot test results
+--------------------
+
+x.x Operation on all available serial consoles
+
+x.x.x CONFIG_CONS_INDEX 1
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> help
+autoscr - run script from memory
+base    - print or set address offset
+bdinfo  - print Board Info structure
+bootm   - boot application image from memory
+bootp   - boot image via network using BootP/TFTP protocol
+bootd   - boot default, i.e., run 'bootcmd'
+cmp     - memory compare
+coninfo - print console devices and informations
+cp      - memory copy
+crc32   - checksum calculation
+dcache  - enable or disable data cache
+echo    - echo args to console
+erase   - erase FLASH memory
+flinfo  - print FLASH memory information
+go      - start application at address 'addr'
+help    - print online help
+icache  - enable or disable instruction cache
+iminfo  - print header information for application image
+loadb   - load binary file over serial line (kermit mode)
+loads   - load S-Record file over serial line
+loop    - infinite loop on address range
+md      - memory display
+mm      - memory modify (auto-incrementing)
+mtest   - simple RAM test
+mw      - memory write (fill)
+nm      - memory modify (constant address)
+printenv- print environment variables
+protect - enable or disable FLASH write protection
+rarpboot- boot image via network using RARP/TFTP protocol
+reset   - Perform RESET of the CPU
+run     - run commands in an environment variable
+saveenv - save environment variables to persistent storage
+setenv  - set environment variables
+tftpboot- boot image via network using TFTP protocol
+               and env variables ipaddr and serverip
+version - print monitor version
+?       - alias for 'help'
+
+
+
+x.x.x CONFIG_CONS_INDEX 2
+
+**** NOT TESTED ****
+
+x.x Flash Driver Operation
+
+
+Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+*** Warning - bad CRC, using default environment
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=>
+=> md ff800000
+ff800000: 46989bf8 626f6f74 636d643d 626f6f74    F...bootcmd=boot
+ff800010: 6d204646 38323030 30300062 6f6f7464    m FF820000.bootd
+ff800020: 656c6179 3d350062 61756472 6174653d    elay=5.baudrate=
+ff800030: 39363030 00636c6f 636b735f 696e5f6d    9600.clocks_in_m
+ff800040: 687a3d31 00737464 696e3d73 65726961    hz=1.stdin=seria
+ff800050: 6c007374 646f7574 3d736572 69616c00    l.stdout=serial.
+ff800060: 73746465 72723d73 65726961 6c006970    stderr=serial.ip
+ff800070: 61646472 3d313932 2e313638 2e302e34    addr=192.168.0.4
+ff800080: 32007365 72766572 69703d31 39322e31    2.serverip=192.1
+ff800090: 36382e30 2e380000 00000000 00000000    68.0.8..........
+ff8000a0: 00000000 00000000 00000000 00000000    ................
+ff8000b0: 00000000 00000000 00000000 00000000    ................
+ff8000c0: 00000000 00000000 00000000 00000000    ................
+ff8000d0: 00000000 00000000 00000000 00000000    ................
+ff8000e0: 00000000 00000000 00000000 00000000    ................
+ff8000f0: 00000000 00000000 00000000 00000000    ................
+=> protect off ff800000 ff81ffff
+Un-Protected 1 sectors
+=> erase ff800000 ff81ffff
+Erase Flash from 0xff800000 to 0xff81ffff
+ done
+Erased 1 sectors
+=> md ff800000
+ff800000: ffffffff ffffffff ffffffff ffffffff    ................
+ff800010: ffffffff ffffffff ffffffff ffffffff    ................
+ff800020: ffffffff ffffffff ffffffff ffffffff    ................
+ff800030: ffffffff ffffffff ffffffff ffffffff    ................
+ff800040: ffffffff ffffffff ffffffff ffffffff    ................
+ff800050: ffffffff ffffffff ffffffff ffffffff    ................
+ff800060: ffffffff ffffffff ffffffff ffffffff    ................
+ff800070: ffffffff ffffffff ffffffff ffffffff    ................
+ff800080: ffffffff ffffffff ffffffff ffffffff    ................
+ff800090: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000a0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000b0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000c0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000d0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000e0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000f0: ffffffff ffffffff ffffffff ffffffff    ................
+
+x.x.x Information
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+*** Warning - bad CRC, using default environment
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> flinfo
+
+Bank # 1: Intel 28F320J3A (32Mbit = 128K x 32)
+  Size: 4 MB in 32 Sectors
+  Sector Start Addresses:
+    FF800000 (RO) FF820000      FF840000      FF860000      FF880000
+    FF8A0000      FF8C0000      FF8E0000      FF900000      FF920000
+    FF940000      FF960000      FF980000      FF9A0000      FF9C0000
+    FF9E0000      FFA00000      FFA20000      FFA40000      FFA60000
+    FFA80000      FFAA0000      FFAC0000      FFAE0000      FFB00000
+    FFB20000      FFB40000      FFB60000      FFB80000      FFBA0000
+    FFBC0000      FFBE0000
+
+Bank # 2: missing or unknown FLASH type
+=>
+
+
+
+x.x.x Flash Programming
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=>
+=>
+=>
+=> protect off ff800000 ff81ffff
+Un-Protected 1 sectors
+=> cp 0 ff800000 20
+Copy to Flash... done
+=> md ff800000
+ff800000: 37ce33ec 33cc334c 33c031cc 33cc35cc    7.3.3.3L3.1.3.5.
+ff800010: 33ec13ce 30ccb3ec b3c833c4 31c836cc    3...0.....3.1.6.
+ff800020: 33cc3b9d 31ec33ee 13ecf3cc 338833ec    3.;.1.3.....3.3.
+ff800030: 234c33ec 32cc22cc 33883bdc 534433cc    #L3.2.".3.;.SD3.
+ff800040: 33cc30c8 31cc32ec 338c33cc 330c33dc    3.0.1.2.3.3.3.3.
+ff800050: 33cc13dc 334c534c b1c433d8 128c13cc    3...3LSL..3.....
+ff800060: 37ec36cd 33dc33cc bbc9f7e8 bbcc77cc    7.6.3.3.......w.
+ff800070: 314c0adc 139c30ed 33cc334c 33c833ec    1L....0.3.3L3.3.
+ff800080: ffffffff ffffffff ffffffff ffffffff    ................
+ff800090: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000a0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000b0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000c0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000d0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000e0: ffffffff ffffffff ffffffff ffffffff    ................
+ff8000f0: ffffffff ffffffff ffffffff ffffffff    ................
+
+
+x.x.x Storage of environment variables in flash
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> printenv
+bootcmd=bootm FF820000
+bootdelay=5
+baudrate=9600
+clocks_in_mhz=1
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 106/16380 bytes
+=> setenv myvar 1234
+=> saveenv
+Un-Protected 1 sectors
+Erasing Flash...
+ done
+Erased 1 sectors
+Saving Environment to Flash...
+Protected 1 sectors
+=> reset
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> printenv
+bootcmd=bootm FF820000
+bootdelay=5
+baudrate=9600
+clocks_in_mhz=1
+myvar=1234
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 117/16380 bytes
+
+x.x Image Download and run over serial port
+
+
+U-Boot 1.1.1 (Nov 20 2001 - 15:55:32)
+
+CPU:   MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache
+Board: MUSENKI Local Bus at 100 MHz
+DRAM:  32 MB
+FLASH:  4 MB
+In:    serial
+Out:   serial
+Err:   serial
+Hit any key to stop autoboot:  0
+=> loads
+## Ready for S-Record download ...
+
+## First Load Addr = 0x00040000
+## Last  Load Addr = 0x00050177
+## Total Size      = 0x00010178 = 65912 Bytes
+## Start Addr      = 0x00040004
+=> go 40004
+## Starting application at 0x00040004 ...
+Hello World
+argc = 1
+argv[0] = "40004"
+argv[1] = "<NULL>"
+Hit any key to exit ...
+
+## Application terminated, rc = 0x0
+
+
+x.x Image download and run over ethernet interface
+
+untested (not working yet, actually)
+
diff --git a/board/pcippc2/u-boot.lds b/board/pcippc2/u-boot.lds
new file mode 100644
index 00000000000..25ff2ffa3b7
--- /dev/null
+++ b/board/pcippc2/u-boot.lds
@@ -0,0 +1,132 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * u-boot.lds - linker script for U-Boot on the Galileo Eval Board.
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/74xx_7xx/start.o	(.text)
+
+/* store the environment in a seperate sector in the boot flash */
+/*    . = env_offset; */
+/*    common/environment.o(.text) */
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
diff --git a/board/pm826/config.mk b/board/pm826/config.mk
new file mode 100644
index 00000000000..8502e3f1071
--- /dev/null
+++ b/board/pm826/config.mk
@@ -0,0 +1,42 @@
+#
+# (C) Copyright 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# PM826 boards
+#
+
+# This should be equal to the CFG_FLASH_BASE or
+# CFG_BOOTROM_BASE define in config_PM826.h
+# for the "final" configuration, with U-Boot
+# in flash, or the address in RAM where
+# U-Boot is loaded at for debugging.
+#
+
+ifeq ($(CONFIG_BOOT_ROM),y)
+	TEXT_BASE := 0x60000000
+	PLATFORM_CPPFLAGS += -DCONFIG_BOOT_ROM
+else
+	TEXT_BASE := 0x40000000
+endif
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)
diff --git a/board/rpxsuper/readme b/board/rpxsuper/readme
new file mode 100644
index 00000000000..21267bdd8ca
--- /dev/null
+++ b/board/rpxsuper/readme
@@ -0,0 +1,30 @@
+Hi,
+
+so this is the port to the Embedded Planet RPX Super Board.
+
+ATTENTION
+This code is only tested on the AY-Version, which is an early release with some
+hardware bugs. The main problem is that this board uses the default Hard Reset
+Configuration Word and not the 4 bytes located at start of FLASH because at
+0xFE000000 is no FLASH. The FLASH consists out of 4 chips each 16bits wide. Be
+carefull, the bytes are swapped. So DQ0-7 is the high byte, DQ8-15 ist the low
+byte.
+
+The icache can only manually be enabled after reset.
+The FLASH and main SDRAM is working with icache enabled.
+The local SDRAM can only be used as data memory when icache is enabled.
+If U-Boot runs in local SDRAM, TFTP does not work.
+The functions in mii_phy.c are all working. Call mii_phy_discover() out of
+eth_init() and solve the linker error.
+I2C, RTC/NVRAM and PCMCIA are not working yet.
+
+TODO
+The 32MB local SDRAM is working but not shown in the startup messages of
+U-Boot. If you locate U-Boot or any other program to this area it won't run.
+Turning the ichache off does not solve this problem.
+
+As I won't buy another RPX Super there might be some little work to do for you
+getting this U-Boot port running on the final board.
+
+
+frank.morauf@salzbrenner.com
diff --git a/board/siemens/SCM/config.mk b/board/siemens/SCM/config.mk
new file mode 100644
index 00000000000..855ae38f817
--- /dev/null
+++ b/board/siemens/SCM/config.mk
@@ -0,0 +1,34 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Siemens SCM boards
+#
+
+# This should be equal to the CFG_FLASH_BASE define in config_SCM.h
+# for the "final" configuration, with U-Boot in flash, or the address
+# in RAM where U-Boot is loaded at for debugging.
+#
+TEXT_BASE = 0x40000000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)
diff --git a/board/tqm8260/config.mk b/board/tqm8260/config.mk
new file mode 100644
index 00000000000..1fe99524c66
--- /dev/null
+++ b/board/tqm8260/config.mk
@@ -0,0 +1,34 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# TQM8260 boards
+#
+
+# This should be equal to the CFG_FLASH_BASE define in config_TQM8260.h
+# for the "final" configuration, with U-Boot in flash, or the address
+# in RAM where U-Boot is loaded at for debugging.
+#
+TEXT_BASE = 0x40000000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)
diff --git a/common/fpga.c b/common/fpga.c
new file mode 100644
index 00000000000..c5975bcf6cd
--- /dev/null
+++ b/common/fpga.c
@@ -0,0 +1,351 @@
+/*
+ * (C) Copyright 2002
+ * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/*
+ *  Generic FPGA support
+ */
+#include <common.h>             /* core U-Boot definitions */
+#include <xilinx.h>             /* xilinx specific definitions */
+#include <altera.h>             /* altera specific definitions */
+
+#if defined(CONFIG_FPGA)
+
+#if 0
+#define FPGA_DEBUG              /* define FPGA_DEBUG to get debug messages */
+#endif
+
+/* Local definitions */
+#ifndef CONFIG_MAX_FPGA_DEVICES
+#define CONFIG_MAX_FPGA_DEVICES		5
+#endif
+
+/* Enable/Disable debug console messages */
+#ifdef FPGA_DEBUG
+#define	PRINTF(fmt,args...)	printf (fmt ,##args)
+#else
+#define	PRINTF(fmt,args...)
+#endif
+
+/* Local static data */
+static ulong relocation_offset = 0;
+static int next_desc = FPGA_INVALID_DEVICE;
+static fpga_desc desc_table[CONFIG_MAX_FPGA_DEVICES];
+
+/* Local static functions */
+static const fpga_desc * const fpga_get_desc( int devnum );
+static const fpga_desc * const fpga_validate( int devnum, void *buf,
+                                         size_t bsize, char *fn );
+static int fpga_dev_info( int devnum );
+
+
+/* ------------------------------------------------------------------------- */
+
+/* fpga_no_sup
+ * 'no support' message function
+ */
+static void fpga_no_sup( char *fn, char *msg )
+{
+	if ( fn && msg ) {
+		printf( "%s: No support for %s.  CONFIG_FPGA defined as 0x%x.\n",
+				fn, msg, CONFIG_FPGA );
+	} else if ( msg ) {
+		printf( "No support for %s. CONFIG_FPGA defined as 0x%x.\n",
+				msg, CONFIG_FPGA );
+	} else {
+		printf( "No FPGA suport!  CONFIG_FPGA defined as 0x%x.\n",
+				CONFIG_FPGA );
+	}
+}
+
+
+/* fpga_get_desc
+ *	map a device number to a descriptor
+ */
+static const fpga_desc * const fpga_get_desc( int devnum )
+{
+	fpga_desc *desc = (fpga_desc * )NULL;
+
+	if (( devnum >= 0 ) && (devnum < next_desc )) {
+		desc = &desc_table[devnum];
+		PRINTF( "%s: found fpga descriptor #%d @ 0x%p\n",
+				__FUNCTION__, devnum, desc );
+	}
+
+	return desc;
+}
+
+
+/* fpga_validate
+ *	generic parameter checking code
+ */
+static const fpga_desc * const fpga_validate( int devnum, void *buf,
+                                         size_t bsize, char *fn )
+{
+	const fpga_desc * const desc = fpga_get_desc( devnum );
+
+	if ( !desc ) {
+		printf( "%s: Invalid device number %d\n", fn, devnum );
+	}
+
+	if ( !buf ) {
+		printf( "%s: Null buffer.\n", fn );
+		return (fpga_desc * const)NULL;
+	}
+	if ( !bsize ) {
+		printf( "%s: Null buffer size.\n", fn );
+		return (fpga_desc * const)NULL;
+	}
+
+	return desc;
+}
+
+
+/* fpga_dev_info
+ *	generic multiplexing code
+ */
+static int fpga_dev_info( int devnum )
+{
+	int ret_val = FPGA_FAIL;           /* assume failure */
+	const fpga_desc * const desc = fpga_get_desc( devnum );
+
+	if ( desc ) {
+		PRINTF( "%s: Device Descriptor @ 0x%p\n",
+				__FUNCTION__, desc->devdesc );
+
+		switch ( desc->devtype ) {
+		case fpga_xilinx:
+#if CONFIG_FPGA & CFG_FPGA_XILINX
+			printf( "Xilinx Device\nDescriptor @ 0x%p\n", desc );
+			ret_val = xilinx_info( desc->devdesc );
+#else
+			fpga_no_sup( __FUNCTION__, "Xilinx devices" );
+#endif
+			break;
+		case fpga_altera:
+#if CONFIG_FPGA & CFG_FPGA_ALTERA
+			printf( "Altera Device\nDescriptor @ 0x%p\n", desc );
+			ret_val = altera_info( desc->devdesc );
+#else
+			fpga_no_sup( __FUNCTION__, "Altera devices" );
+#endif
+			break;
+		default:
+			printf( "%s: Invalid or unsupported device type %d\n",
+					__FUNCTION__, desc->devtype );
+		}
+	} else {
+		printf( "%s: Invalid device number %d\n",
+			__FUNCTION__, devnum );
+	}
+
+	return ret_val;
+}
+
+
+/* fpga_reloc
+ *	generic multiplexing code
+ */
+int fpga_reloc( fpga_type devtype, void *desc, ulong reloc_off )
+{
+	int ret_val = FPGA_FAIL;
+
+	PRINTF( "%s: Relocating Device of type %d @ 0x%p with offset %lx\n",
+				__FUNCTION__, devtype, desc, reloc_off );
+
+	switch ( devtype ) {
+	case fpga_xilinx:
+#if CONFIG_FPGA & CFG_FPGA_XILINX
+		ret_val = xilinx_reloc( desc, reloc_off );
+#else
+		fpga_no_sup( __FUNCTION__, "Xilinx devices" );
+#endif
+		break;
+	case fpga_altera:
+#if CONFIG_FPGA & CFG_FPGA_ALTERA
+		ret_val = altera_reloc( desc, reloc_off );
+#else
+		fpga_no_sup( __FUNCTION__, "Altera devices" );
+#endif
+		break;
+	default:
+		printf( "%s: Invalid or unsupported device type %d\n",
+			__FUNCTION__, devtype );
+	}
+
+	return ret_val;
+}
+
+/* ------------------------------------------------------------------------- */
+/* fgpa_init is usually called from misc_init_r() and MUST be called
+ * before any of the other fpga functions are used.
+ */
+void fpga_init( ulong reloc_off )
+{
+	relocation_offset = reloc_off;
+	next_desc = 0;
+	memset( desc_table, 0, sizeof(desc_table));
+
+	PRINTF( "%s: CONFIG_FPGA = 0x%x\n", __FUNCTION__, CONFIG_FPGA );
+#if 0
+	PRINTF( "%s: CFG_FPGA_XILINX = 0x%x\n", __FUNCTION__, CFG_FPGA_XILINX );
+	PRINTF( "%s: CFG_FPGA_ALTERA = 0x%x\n", __FUNCTION__, CFG_FPGA_ALTERA );
+#endif
+}
+
+/* fpga_count
+ * Basic interface function to get the current number of devices available.
+ */
+const int fpga_count( void )
+{
+	return next_desc;
+}
+
+/* fpga_add
+ *	Attempts to relocate the device/board specific interface code
+ *	to the proper RAM locations and adds the device descriptor to
+ *	the device table.
+ */
+int fpga_add( fpga_type devtype, void *desc )
+{
+	int devnum = FPGA_INVALID_DEVICE;
+
+	if ( next_desc  < 0 ) {
+		printf( "%s: FPGA support not initialized!\n", __FUNCTION__ );
+	} else if (( devtype > fpga_min_type ) && ( devtype < fpga_undefined )) {
+		if ( desc ) {
+			if ( next_desc < CONFIG_MAX_FPGA_DEVICES ) {
+				if ( fpga_reloc( devtype, desc, relocation_offset )
+				  == FPGA_SUCCESS ) {
+					devnum = next_desc;
+					desc_table[next_desc].devtype = devtype;
+					desc_table[next_desc++].devdesc = desc;
+				} else {
+					printf( "%s: Unable to relocate device interface table!\n",
+						__FUNCTION__ );
+				}
+			} else {
+				printf( "%s: Exceeded Max FPGA device count\n", __FUNCTION__ );
+			}
+		} else {
+			printf( "%s: NULL device descriptor\n", __FUNCTION__ );
+		}
+	} else {
+		printf( "%s: Unsupported FPGA type %d\n", __FUNCTION__, devtype );
+	}
+
+	return devnum;
+}
+
+/*
+ *	Generic multiplexing code
+ */
+int fpga_load( int devnum, void *buf, size_t bsize )
+{
+	int ret_val = FPGA_FAIL;           /* assume failure */
+	const fpga_desc * const desc = fpga_validate( devnum, buf, bsize, __FUNCTION__ );
+
+	if ( desc ) {
+		switch ( desc->devtype ) {
+		case fpga_xilinx:
+#if CONFIG_FPGA & CFG_FPGA_XILINX
+			ret_val = xilinx_load( desc->devdesc, buf, bsize );
+#else
+			fpga_no_sup( __FUNCTION__, "Xilinx devices" );
+#endif
+			break;
+		case fpga_altera:
+#if CONFIG_FPGA & CFG_FPGA_ALTERA
+			ret_val = altera_load( desc->devdesc, buf, bsize );
+#else
+			fpga_no_sup( __FUNCTION__, "Altera devices" );
+#endif
+			break;
+		default:
+			printf( "%s: Invalid or unsupported device type %d\n",
+				__FUNCTION__, desc->devtype );
+		}
+	}
+
+	return ret_val;
+}
+
+/* fpga_dump
+ *	generic multiplexing code
+ */
+int fpga_dump( int devnum, void *buf, size_t bsize )
+{
+	int ret_val = FPGA_FAIL;           /* assume failure */
+	const fpga_desc * const desc = fpga_validate( devnum, buf, bsize, __FUNCTION__ );
+
+	if ( desc ) {
+		switch ( desc->devtype ) {
+		case fpga_xilinx:
+#if CONFIG_FPGA & CFG_FPGA_XILINX
+			ret_val = xilinx_dump( desc->devdesc, buf, bsize );
+#else
+			fpga_no_sup( __FUNCTION__, "Xilinx devices" );
+#endif
+			break;
+		case fpga_altera:
+#if CONFIG_FPGA & CFG_FPGA_ALTERA
+			ret_val = altera_dump( desc->devdesc, buf, bsize );
+#else
+			fpga_no_sup( __FUNCTION__, "Altera devices" );
+#endif
+			break;
+		default:
+			printf( "%s: Invalid or unsupported device type %d\n",
+				__FUNCTION__, desc->devtype );
+		}
+	}
+
+	return ret_val;
+}
+
+
+/* fpga_info
+ *	front end to fpga_dev_info.  If devnum is invalid, report on all
+ *	available devices.
+ */
+int fpga_info( int devnum )
+{
+	if ( devnum == FPGA_INVALID_DEVICE ) {
+		if ( next_desc > 0 ) {
+			int dev;
+
+			for ( dev = 0; dev < next_desc; dev++ ) {
+				fpga_dev_info( dev );
+			}
+			return FPGA_SUCCESS;
+		} else {
+			printf( "%s: No FPGA devices available.\n", __FUNCTION__ );
+			return FPGA_FAIL;
+		}
+	}
+	else return fpga_dev_info( devnum );
+}
+
+/* ------------------------------------------------------------------------- */
+
+#endif  /* CONFIG_FPGA */
diff --git a/common/spartan2.c b/common/spartan2.c
new file mode 100644
index 00000000000..9ac1e137786
--- /dev/null
+++ b/common/spartan2.c
@@ -0,0 +1,470 @@
+/*
+ * (C) Copyright 2002
+ * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>		/* core U-Boot definitions */
+#include <spartan2.h>		/* Spartan-II device family */
+
+#if (CONFIG_FPGA & (CFG_XILINX | CFG_SPARTAN2))
+
+/* Define FPGA_DEBUG to get debug printf's */
+#ifdef	FPGA_DEBUG
+#define PRINTF(fmt,args...)	printf (fmt ,##args)
+#else
+#define PRINTF(fmt,args...)
+#endif
+
+#undef CFG_FPGA_CHECK_BUSY
+#define CFG_FPGA_PROG_FEEDBACK
+
+/* Note: The assumption is that we cannot possibly run fast enough to
+ * overrun the device (the Slave Parallel mode can free run at 50MHz).
+ * If there is a need to operate slower, define CONFIG_FPGA_DELAY in
+ * the board config file to slow things down.
+ */
+#ifndef CONFIG_FPGA_DELAY
+#define CONFIG_FPGA_DELAY()
+#endif
+
+#ifndef CFG_FPGA_WAIT
+#define CFG_FPGA_WAIT 10
+#endif
+
+static int Spartan2_sp_load( Xilinx_desc *desc, void *buf, size_t bsize );
+static int Spartan2_sp_dump( Xilinx_desc *desc, void *buf, size_t bsize );
+/* static int Spartan2_sp_info( Xilinx_desc *desc ); */
+static int Spartan2_sp_reloc( Xilinx_desc *desc, ulong reloc_offset );
+
+static int Spartan2_ss_load( Xilinx_desc *desc, void *buf, size_t bsize );
+static int Spartan2_ss_dump( Xilinx_desc *desc, void *buf, size_t bsize );
+/* static int Spartan2_ss_info( Xilinx_desc *desc ); */
+static int Spartan2_ss_reloc( Xilinx_desc *desc, ulong reloc_offset );
+
+/* ------------------------------------------------------------------------- */
+/* Spartan-II Generic Implementation */
+int Spartan2_load (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	int ret_val = FPGA_FAIL;
+
+	switch (desc->iface) {
+	case slave_serial:
+		PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__);
+		ret_val = Spartan2_ss_load (desc, buf, bsize);
+		break;
+
+	case slave_parallel:
+		PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__);
+		ret_val = Spartan2_sp_load (desc, buf, bsize);
+		break;
+
+	default:
+		printf ("%s: Unsupported interface type, %d\n",
+				__FUNCTION__, desc->iface);
+	}
+
+	return ret_val;
+}
+
+int Spartan2_dump (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	int ret_val = FPGA_FAIL;
+
+	switch (desc->iface) {
+	case slave_serial:
+		PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__);
+		ret_val = Spartan2_ss_dump (desc, buf, bsize);
+		break;
+
+	case slave_parallel:
+		PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__);
+		ret_val = Spartan2_sp_dump (desc, buf, bsize);
+		break;
+
+	default:
+		printf ("%s: Unsupported interface type, %d\n",
+				__FUNCTION__, desc->iface);
+	}
+
+	return ret_val;
+}
+
+int Spartan2_info( Xilinx_desc *desc )
+{
+	return FPGA_SUCCESS;
+}
+
+
+int Spartan2_reloc (Xilinx_desc * desc, ulong reloc_offset)
+{
+	int ret_val = FPGA_FAIL;	/* assume a failure */
+
+	if (desc->family != Xilinx_Spartan2) {
+		printf ("%s: Unsupported family type, %d\n",
+				__FUNCTION__, desc->family);
+		return FPGA_FAIL;
+	} else
+		switch (desc->iface) {
+		case slave_serial:
+			ret_val = Spartan2_ss_reloc (desc, reloc_offset);
+			break;
+
+		case slave_parallel:
+			ret_val = Spartan2_sp_reloc (desc, reloc_offset);
+			break;
+
+		default:
+			printf ("%s: Unsupported interface type, %d\n",
+					__FUNCTION__, desc->iface);
+		}
+
+	return ret_val;
+}
+
+
+/* ------------------------------------------------------------------------- */
+/* Spartan-II Slave Parallel Generic Implementation */
+
+static int Spartan2_sp_load (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	int ret_val = FPGA_FAIL;	/* assume the worst */
+	Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns;
+
+	PRINTF ("%s: start with interface functions @ 0x%p\n",
+			__FUNCTION__, fn);
+
+	if (fn) {
+		size_t bytecount = 0;
+		unsigned char *data = (unsigned char *) buf;
+		int cookie = desc->cookie;	/* make a local copy */
+		unsigned long ts;		/* timestamp */
+
+		PRINTF ("%s: Function Table:\n"
+				"ptr:\t0x%p\n"
+				"struct: 0x%p\n"
+				"pre: 0x%p\n"
+				"pgm:\t0x%p\n"
+				"init:\t0x%p\n"
+				"err:\t0x%p\n"
+				"clk:\t0x%p\n"
+				"cs:\t0x%p\n"
+				"wr:\t0x%p\n"
+				"read data:\t0x%p\n"
+				"write data:\t0x%p\n"
+				"busy:\t0x%p\n"
+				"abort:\t0x%p\n",
+				"post:\t0x%p\n\n",
+				__FUNCTION__, &fn, fn, fn->pre, fn->pgm, fn->init, fn->err,
+				fn->clk, fn->cs, fn->wr, fn->rdata, fn->wdata, fn->busy,
+				fn->abort, fn->post);
+
+		/*
+		 * This code is designed to emulate the "Express Style"
+		 * Continuous Data Loading in Slave Parallel Mode for
+		 * the Spartan-II Family.
+		 */
+#ifdef CFG_FPGA_PROG_FEEDBACK
+		printf ("Loading FPGA Device %d...\n", cookie);
+#endif
+		/*
+		 * Run the pre configuration function if there is one.
+		 */
+		if (*fn->pre) {
+			(*fn->pre) (cookie);
+		}
+
+		/* Establish the initial state */
+		(*fn->pgm) (TRUE, TRUE, cookie);	/* Assert the program, commit */
+
+		/* Get ready for the burn */
+		CONFIG_FPGA_DELAY ();
+		(*fn->pgm) (FALSE, TRUE, cookie);	/* Deassert the program, commit */
+
+		ts = get_timer (0);		/* get current time */
+		/* Now wait for INIT and BUSY to go high */
+		do {
+			CONFIG_FPGA_DELAY ();
+			if (get_timer (ts) > CFG_FPGA_WAIT) {	/* check the time */
+				puts ("** Timeout waiting for INIT to clear.\n");
+				(*fn->abort) (cookie);	/* abort the burn */
+				return FPGA_FAIL;
+			}
+		} while ((*fn->init) (cookie) && (*fn->busy) (cookie));
+
+		(*fn->wr) (TRUE, TRUE, cookie); /* Assert write, commit */
+		(*fn->cs) (TRUE, TRUE, cookie); /* Assert chip select, commit */
+		(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+		/* Load the data */
+		while (bytecount < bsize) {
+			/* XXX - do we check for an Ctrl-C press in here ??? */
+			/* XXX - Check the error bit? */
+
+			(*fn->wdata) (data[bytecount++], TRUE, cookie); /* write the data */
+			CONFIG_FPGA_DELAY ();
+			(*fn->clk) (FALSE, TRUE, cookie);	/* Deassert the clock pin */
+			CONFIG_FPGA_DELAY ();
+			(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+#ifdef CFG_FPGA_CHECK_BUSY
+			ts = get_timer (0);	/* get current time */
+			while ((*fn->busy) (cookie)) {
+				/* XXX - we should have a check in here somewhere to
+				 * make sure we aren't busy forever... */
+
+				CONFIG_FPGA_DELAY ();
+				(*fn->clk) (FALSE, TRUE, cookie);	/* Deassert the clock pin */
+				CONFIG_FPGA_DELAY ();
+				(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+				if (get_timer (ts) > CFG_FPGA_WAIT) {	/* check the time */
+					puts ("** Timeout waiting for BUSY to clear.\n");
+					(*fn->abort) (cookie);	/* abort the burn */
+					return FPGA_FAIL;
+				}
+			}
+#endif
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+			if (bytecount % (bsize / 40) == 0)
+				putc ('.');		/* let them know we are alive */
+#endif
+		}
+
+		CONFIG_FPGA_DELAY ();
+		(*fn->cs) (FALSE, TRUE, cookie);	/* Deassert the chip select */
+		(*fn->wr) (FALSE, TRUE, cookie);	/* Deassert the write pin */
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+		putc ('\n');			/* terminate the dotted line */
+#endif
+
+		/* now check for done signal */
+		ts = get_timer (0);		/* get current time */
+		ret_val = FPGA_SUCCESS;
+		while ((*fn->done) (cookie) == FPGA_FAIL) {
+			/* XXX - we should have a check in here somewhere to
+			 * make sure we aren't busy forever... */
+
+			CONFIG_FPGA_DELAY ();
+			(*fn->clk) (FALSE, TRUE, cookie);	/* Deassert the clock pin */
+			CONFIG_FPGA_DELAY ();
+			(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+			if (get_timer (ts) > CFG_FPGA_WAIT) {	/* check the time */
+				puts ("** Timeout waiting for DONE to clear.\n");
+				(*fn->abort) (cookie);	/* abort the burn */
+				ret_val = FPGA_FAIL;
+				break;
+			}
+		}
+
+		if (ret_val == FPGA_SUCCESS) {
+#ifdef CFG_FPGA_PROG_FEEDBACK
+			puts ("Done.\n");
+#endif
+		}
+		/*
+		 * Run the post configuration function if there is one.
+		 */
+		if (*fn->post) {
+			(*fn->post) (cookie);
+		}
+
+		else {
+#ifdef CFG_FPGA_PROG_FEEDBACK
+			puts ("Fail.\n");
+#endif
+		}
+
+	} else {
+		printf ("%s: NULL Interface function table!\n", __FUNCTION__);
+	}
+
+	return ret_val;
+}
+
+static int Spartan2_sp_dump (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	int ret_val = FPGA_FAIL;	/* assume the worst */
+	Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns;
+
+	if (fn) {
+		unsigned char *data = (unsigned char *) buf;
+		size_t bytecount = 0;
+		int cookie = desc->cookie;	/* make a local copy */
+
+		printf ("Starting Dump of FPGA Device %d...\n", cookie);
+
+		(*fn->cs) (TRUE, TRUE, cookie); /* Assert chip select, commit */
+		(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+		/* dump the data */
+		while (bytecount < bsize) {
+			/* XXX - do we check for an Ctrl-C press in here ??? */
+
+			(*fn->clk) (FALSE, TRUE, cookie);	/* Deassert the clock pin */
+			(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+			(*fn->rdata) (&(data[bytecount++]), cookie);	/* read the data */
+#ifdef CFG_FPGA_PROG_FEEDBACK
+			if (bytecount % (bsize / 40) == 0)
+				putc ('.');		/* let them know we are alive */
+#endif
+		}
+
+		(*fn->cs) (FALSE, FALSE, cookie);	/* Deassert the chip select */
+		(*fn->clk) (FALSE, TRUE, cookie);	/* Deassert the clock pin */
+		(*fn->clk) (TRUE, TRUE, cookie);	/* Assert the clock pin */
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+		putc ('\n');			/* terminate the dotted line */
+#endif
+		puts ("Done.\n");
+
+		/* XXX - checksum the data? */
+	} else {
+		printf ("%s: NULL Interface function table!\n", __FUNCTION__);
+	}
+
+	return ret_val;
+}
+
+
+static int Spartan2_sp_reloc (Xilinx_desc * desc, ulong reloc_offset)
+{
+	int ret_val = FPGA_FAIL;	/* assume the worst */
+	Xilinx_Spartan2_Slave_Parallel_fns *fn_r, *fn =
+			(Xilinx_Spartan2_Slave_Parallel_fns *) (desc->iface_fns);
+
+	if (fn) {
+		ulong addr;
+
+		/* Get the relocated table address */
+		addr = (ulong) fn + reloc_offset;
+		fn_r = (Xilinx_Spartan2_Slave_Parallel_fns *) addr;
+
+		if (!fn_r->relocated) {
+
+			if (memcmp (fn_r, fn,
+						sizeof (Xilinx_Spartan2_Slave_Parallel_fns))
+				== 0) {
+				/* good copy of the table, fix the descriptor pointer */
+				desc->iface_fns = fn_r;
+			} else {
+				PRINTF ("%s: Invalid function table at 0x%p\n",
+						__FUNCTION__, fn_r);
+				return FPGA_FAIL;
+			}
+
+			PRINTF ("%s: Relocating descriptor at 0x%p\n", __FUNCTION__,
+					desc);
+
+			addr = (ulong) (fn->pre) + reloc_offset;
+			fn_r->pre = (Xilinx_pre_fn) addr;
+
+			addr = (ulong) (fn->pgm) + reloc_offset;
+			fn_r->pgm = (Xilinx_pgm_fn) addr;
+
+			addr = (ulong) (fn->init) + reloc_offset;
+			fn_r->init = (Xilinx_init_fn) addr;
+
+			addr = (ulong) (fn->done) + reloc_offset;
+			fn_r->done = (Xilinx_done_fn) addr;
+
+			addr = (ulong) (fn->clk) + reloc_offset;
+			fn_r->clk = (Xilinx_clk_fn) addr;
+
+			addr = (ulong) (fn->err) + reloc_offset;
+			fn_r->err = (Xilinx_err_fn) addr;
+
+			addr = (ulong) (fn->cs) + reloc_offset;
+			fn_r->cs = (Xilinx_cs_fn) addr;
+
+			addr = (ulong) (fn->wr) + reloc_offset;
+			fn_r->wr = (Xilinx_wr_fn) addr;
+
+			addr = (ulong) (fn->rdata) + reloc_offset;
+			fn_r->rdata = (Xilinx_rdata_fn) addr;
+
+			addr = (ulong) (fn->wdata) + reloc_offset;
+			fn_r->wdata = (Xilinx_wdata_fn) addr;
+
+			addr = (ulong) (fn->busy) + reloc_offset;
+			fn_r->busy = (Xilinx_busy_fn) addr;
+
+			addr = (ulong) (fn->abort) + reloc_offset;
+			fn_r->abort = (Xilinx_abort_fn) addr;
+
+			addr = (ulong) (fn->post) + reloc_offset;
+			fn_r->post = (Xilinx_post_fn) addr;
+
+			fn_r->relocated = TRUE;
+
+		} else {
+			/* this table has already been moved */
+			/* XXX - should check to see if the descriptor is correct */
+			desc->iface_fns = fn_r;
+		}
+
+		ret_val = FPGA_SUCCESS;
+	} else {
+		printf ("%s: NULL Interface function table!\n", __FUNCTION__);
+	}
+
+	return ret_val;
+
+}
+
+/* ------------------------------------------------------------------------- */
+
+static int Spartan2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	printf ("%s: Slave Serial Loading is still unsupported\n",
+			__FUNCTION__);
+	return FPGA_FAIL;
+}
+
+static int Spartan2_ss_dump (Xilinx_desc * desc, void *buf, size_t bsize)
+{
+	printf ("%s: Slave Serial Dumping is still unsupported\n",
+			__FUNCTION__);
+	return FPGA_FAIL;
+}
+
+static int Spartan2_ss_reloc (Xilinx_desc * desc, ulong reloc_offset)
+{
+	int ret_val = FPGA_FAIL;	/* assume the worst */
+	Xilinx_Spartan2_Slave_Serial_fns *fn =
+			(Xilinx_Spartan2_Slave_Serial_fns *) (desc->iface_fns);
+
+	if (fn) {
+		printf ("%s: Slave Serial Loading is still unsupported\n",
+				__FUNCTION__);
+	} else {
+		printf ("%s: NULL Interface function table!\n", __FUNCTION__);
+	}
+
+	return ret_val;
+
+}
+
+#endif
diff --git a/config.mk b/config.mk
new file mode 100644
index 00000000000..ef3c7037edf
--- /dev/null
+++ b/config.mk
@@ -0,0 +1,156 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#########################################################################
+
+#
+# When cross-compiling on NetBSD, we have to define __PPC__ or else we
+# will pick up a va_list declaration that is incompatible with the
+# actual argument lists emitted by the compiler.
+#
+# [Tested on NetBSD/i386 1.5 + cross-powerpc-netbsd-1.3]
+
+ifeq ($(ARCH),ppc)
+ifeq ($(CROSS_COMPILE),powerpc-netbsd-)
+PLATFORM_CPPFLAGS+= -D__PPC__
+endif
+ifeq ($(CROSS_COMPILE),powerpc-openbsd-)
+PLATFORM_CPPFLAGS+= -D__PPC__
+endif
+endif
+
+ifeq ($(ARCH),arm)
+ifeq ($(CROSS_COMPILE),powerpc-netbsd-)
+PLATFORM_CPPFLAGS+= -D__ARM__
+endif
+ifeq ($(CROSS_COMPILE),powerpc-openbsd-)
+PLATFORM_CPPFLAGS+= -D__ARM__
+endif
+endif
+
+ifdef	ARCH
+sinclude $(TOPDIR)/$(ARCH)_config.mk	# include architecture dependend rules
+endif
+ifdef	CPU
+sinclude $(TOPDIR)/cpu/$(CPU)/config.mk	# include  CPU	specific rules
+endif
+ifdef	VENDOR
+BOARDDIR = $(VENDOR)/$(BOARD)
+else
+BOARDDIR = $(BOARD)
+endif
+ifdef	BOARD
+sinclude $(TOPDIR)/board/$(BOARDDIR)/config.mk	# include board specific rules
+endif
+
+#########################################################################
+
+CONFIG_SHELL	:= $(shell if [ -x "$$BASH" ]; then echo $$BASH; \
+		    else if [ -x /bin/bash ]; then echo /bin/bash; \
+		    else echo sh; fi ; fi)
+
+ifeq ($(HOSTOS)-$(HOSTARCH),darwin-ppc)
+HOSTCC		= cc
+else
+HOSTCC		= gcc
+endif
+HOSTCFLAGS	= -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer
+HOSTSTRIP	= strip
+
+#########################################################################
+
+#
+# Include the make variables (CC, etc...)
+#
+AS	= $(CROSS_COMPILE)as
+LD	= $(CROSS_COMPILE)ld
+CC	= $(CROSS_COMPILE)gcc
+CPP	= $(CC) -E
+AR	= $(CROSS_COMPILE)ar
+NM	= $(CROSS_COMPILE)nm
+STRIP	= $(CROSS_COMPILE)strip
+OBJCOPY = $(CROSS_COMPILE)objcopy
+OBJDUMP = $(CROSS_COMPILE)objdump
+RANLIB	= $(CROSS_COMPILE)RANLIB
+
+RELFLAGS= $(PLATFORM_RELFLAGS)
+DBGFLAGS= -g #-DDEBUG
+OPTFLAGS= -Os #-fomit-frame-pointer
+#LDSCRIPT := board/$(BOARDDIR)/u-boot.lds.debug
+LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
+OBJCFLAGS := --gap-fill=0xff
+
+CPPFLAGS := $(DBGFLAGS) $(OPTFLAGS) $(RELFLAGS)		\
+	-D__KERNEL__ -DTEXT_BASE=$(TEXT_BASE)		\
+	-I$(TOPDIR)/include				\
+	-fno-builtin					\
+	-pipe $(PLATFORM_CPPFLAGS)
+
+ifdef BUILD_TAG
+CFLAGS := $(CPPFLAGS) -Wall -Wstrict-prototypes \
+	-DBUILD_TAG='"$(BUILD_TAG)"'
+else
+CFLAGS := $(CPPFLAGS) -Wall -Wstrict-prototypes
+endif
+
+AFLAGS_DEBUG := -Wa,-gstabs
+AFLAGS := $(AFLAGS_DEBUG) -D__ASSEMBLY__ $(CPPFLAGS)
+
+LDFLAGS += -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE)
+
+# Location of a usable BFD library, where we define "usable" as
+# "built for ${HOST}, supports ${TARGET}".  Sensible values are
+# - When cross-compiling: the root of the cross-environment
+# - Linux/ppc (native): /usr
+# - NetBSD/ppc (native): you lose ... (must extract these from the
+#   binutils build directory, plus the native and U-Boot include
+#   files don't like each other)
+#
+# So far, this is used only by tools/gdb/Makefile.
+
+ifeq ($(HOSTOS)-$(HOSTARCH),darwin-ppc)
+BFD_ROOT_DIR =		/usr/local/tools
+else
+#BFD_ROOT_DIR =		/LinuxPPC/CDK		# Linux/i386
+#BFD_ROOT_DIR =		/usr/pkg/cross		# NetBSD/i386
+#BFD_ROOT_DIR =		/usr			# native
+BFD_ROOT_DIR =		/opt/powerpc
+endif
+
+#########################################################################
+
+export	CONFIG_SHELL HPATH HOSTCC HOSTCFLAGS CROSS_COMPILE \
+	AS LD CC CPP AR NM STRIP OBJCOPY OBJDUMP \
+	MAKE
+export	TEXT_BASE PLATFORM_CPPFLAGS PLATFORM_RELFLAGS CPPFLAGS CFLAGS AFLAGS
+
+#########################################################################
+
+%.s:	%.S
+	$(CPP) $(AFLAGS) -o $@ $(CURDIR)/$<
+%.o:	%.S
+	$(CC) $(AFLAGS) -c -o $@ $(CURDIR)/$<
+%.o:	%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+#########################################################################
diff --git a/cpu/mpc824x/drivers/epic/epic.h b/cpu/mpc824x/drivers/epic/epic.h
new file mode 100644
index 00000000000..7751db2e7ab
--- /dev/null
+++ b/cpu/mpc824x/drivers/epic/epic.h
@@ -0,0 +1,160 @@
+/*********************************************************************
+ * mpc8240epic.h - EPIC module of the MPC8240 micro-controller
+ *
+ * Copyrigh 1999  Motorola Inc.
+ *
+ * Modification History:
+ * =====================
+ * 01a,04Feb99,My  Created.
+ * 15Nov200, robt -modified to use in U-Boot
+ *
+*/
+
+#ifndef __INCEPICh
+#define __INCEPICh
+
+#define ULONG unsigned long
+#define MAXVEC             20
+#define MAXIRQ        5 /* IRQs */
+#define EPIC_DIRECT_IRQ     0 /* Direct interrupt type */
+
+/* EPIC register addresses */
+
+#define EPIC_EUMBBAR      0x40000     /* EUMBBAR of EPIC  */
+#define EPIC_FEATURES_REG (EPIC_EUMBBAR + 0x01000)/* Feature reporting */
+#define EPIC_GLOBAL_REG   (EPIC_EUMBBAR + 0x01020)/* Global config.  */
+#define EPIC_INT_CONF_REG (EPIC_EUMBBAR + 0x01030)/* Interrupt config. */
+#define EPIC_VENDOR_ID_REG  (EPIC_EUMBBAR + 0x01080)/* Vendor id */
+#define EPIC_PROC_INIT_REG  (EPIC_EUMBBAR + 0x01090)/* Processor init. */
+#define EPIC_SPUR_VEC_REG (EPIC_EUMBBAR + 0x010e0)/* Spurious vector */
+#define EPIC_TM_FREQ_REG  (EPIC_EUMBBAR + 0x010f0)/* Timer Frequency */
+
+#define EPIC_TM0_CUR_COUNT_REG  (EPIC_EUMBBAR + 0x01100)/* Gbl TM0 Cur. Count*/
+#define EPIC_TM0_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01110)/* Gbl TM0 Base Count*/
+#define EPIC_TM0_VEC_REG  (EPIC_EUMBBAR + 0x01120)/* Gbl TM0 Vector Pri*/
+#define EPIC_TM0_DES_REG  (EPIC_EUMBBAR + 0x01130)/* Gbl TM0 Dest. */
+
+#define EPIC_TM1_CUR_COUNT_REG  (EPIC_EUMBBAR + 0x01140)/* Gbl TM1 Cur. Count*/
+#define EPIC_TM1_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01150)/* Gbl TM1 Base Count*/
+#define EPIC_TM1_VEC_REG  (EPIC_EUMBBAR + 0x01160)/* Gbl TM1 Vector Pri*/
+#define EPIC_TM1_DES_REG  (EPIC_EUMBBAR + 0x01170)/* Gbl TM1 Dest. */
+
+#define EPIC_TM2_CUR_COUNT_REG  (EPIC_EUMBBAR + 0x01180)/* Gbl TM2 Cur. Count*/
+#define EPIC_TM2_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01190)/* Gbl TM2 Base Count*/
+#define EPIC_TM2_VEC_REG  (EPIC_EUMBBAR + 0x011a0)/* Gbl TM2 Vector Pri*/
+#define EPIC_TM2_DES_REG  (EPIC_EUMBBAR + 0x011b0)/* Gbl TM2 Dest */
+
+#define EPIC_TM3_CUR_COUNT_REG  (EPIC_EUMBBAR + 0x011c0)/* Gbl TM3 Cur. Count*/
+#define EPIC_TM3_BASE_COUNT_REG (EPIC_EUMBBAR + 0x011d0)/* Gbl TM3 Base Count*/
+#define EPIC_TM3_VEC_REG  (EPIC_EUMBBAR + 0x011e0)/* Gbl TM3 Vector Pri*/
+#define EPIC_TM3_DES_REG  (EPIC_EUMBBAR + 0x011f0)/* Gbl TM3 Dest. */
+
+#define EPIC_EX_INT0_VEC_REG  (EPIC_EUMBBAR + 0x10200)/* Ext. Int. Sr0 Des */
+#define EPIC_EX_INT0_DES_REG  (EPIC_EUMBBAR + 0x10210)/* Ext. Int. Sr0 Vect*/
+#define EPIC_EX_INT1_VEC_REG  (EPIC_EUMBBAR + 0x10220)/* Ext. Int. Sr1 Des */
+#define EPIC_EX_INT1_DES_REG  (EPIC_EUMBBAR + 0x10230)/* Ext. Int. Sr1 Vect*/
+#define EPIC_EX_INT2_VEC_REG  (EPIC_EUMBBAR + 0x10240)/* Ext. Int. Sr2 Des */
+#define EPIC_EX_INT2_DES_REG  (EPIC_EUMBBAR + 0x10250)/* Ext. Int. Sr2 Vect*/
+#define EPIC_EX_INT3_VEC_REG  (EPIC_EUMBBAR + 0x10260)/* Ext. Int. Sr3 Des */
+#define EPIC_EX_INT3_DES_REG  (EPIC_EUMBBAR + 0x10270)/* Ext. Int. Sr3 Vect*/
+#define EPIC_EX_INT4_VEC_REG  (EPIC_EUMBBAR + 0x10280)/* Ext. Int. Sr4 Des */
+#define EPIC_EX_INT4_DES_REG  (EPIC_EUMBBAR + 0x10290)/* Ext. Int. Sr4 Vect*/
+
+#define EPIC_SR_INT0_VEC_REG  (EPIC_EUMBBAR + 0x10200)/* Sr. Int. Sr0 Des */
+#define EPIC_SR_INT0_DES_REG  (EPIC_EUMBBAR + 0x10210)/* Sr. Int. Sr0 Vect */
+#define EPIC_SR_INT1_VEC_REG  (EPIC_EUMBBAR + 0x10220)/* Sr. Int. Sr1 Des */
+#define EPIC_SR_INT1_DES_REG  (EPIC_EUMBBAR + 0x10230)/* Sr. Int. Sr1 Vect.*/
+#define EPIC_SR_INT2_VEC_REG  (EPIC_EUMBBAR + 0x10240)/* Sr. Int. Sr2 Des */
+#define EPIC_SR_INT2_DES_REG  (EPIC_EUMBBAR + 0x10250)/* Sr. Int. Sr2 Vect.*/
+#define EPIC_SR_INT3_VEC_REG  (EPIC_EUMBBAR + 0x10260)/* Sr. Int. Sr3 Des */
+#define EPIC_SR_INT3_DES_REG  (EPIC_EUMBBAR + 0x10270)/* Sr. Int. Sr3 Vect.*/
+#define EPIC_SR_INT4_VEC_REG  (EPIC_EUMBBAR + 0x10280)/* Sr. Int. Sr4 Des */
+#define EPIC_SR_INT4_DES_REG  (EPIC_EUMBBAR + 0x10290)/* Sr. Int. Sr4 Vect.*/
+
+#define EPIC_SR_INT5_VEC_REG  (EPIC_EUMBBAR + 0x102a0)/* Sr. Int. Sr5 Des */
+#define EPIC_SR_INT5_DES_REG  (EPIC_EUMBBAR + 0x102b0)/* Sr. Int. Sr5 Vect.*/
+#define EPIC_SR_INT6_VEC_REG  (EPIC_EUMBBAR + 0x102c0)/* Sr. Int. Sr6 Des */
+#define EPIC_SR_INT6_DES_REG  (EPIC_EUMBBAR + 0x102d0)/* Sr. Int. Sr6 Vect.*/
+#define EPIC_SR_INT7_VEC_REG  (EPIC_EUMBBAR + 0x102e0)/* Sr. Int. Sr7 Des */
+#define EPIC_SR_INT7_DES_REG  (EPIC_EUMBBAR + 0x102f0)/* Sr. Int. Sr7 Vect.*/
+#define EPIC_SR_INT8_VEC_REG  (EPIC_EUMBBAR + 0x10300)/* Sr. Int. Sr8 Des */
+#define EPIC_SR_INT8_DES_REG  (EPIC_EUMBBAR + 0x10310)/* Sr. Int. Sr8 Vect.*/
+#define EPIC_SR_INT9_VEC_REG  (EPIC_EUMBBAR + 0x10320)/* Sr. Int. Sr9 Des */
+#define EPIC_SR_INT9_DES_REG  (EPIC_EUMBBAR + 0x10330)/* Sr. Int. Sr9 Vect.*/
+
+#define EPIC_SR_INT10_VEC_REG (EPIC_EUMBBAR + 0x10340)/* Sr. Int. Sr10 Des */
+#define EPIC_SR_INT10_DES_REG (EPIC_EUMBBAR + 0x10350)/* Sr. Int. Sr10 Vect*/
+#define EPIC_SR_INT11_VEC_REG (EPIC_EUMBBAR + 0x10360)/* Sr. Int. Sr11 Des */
+#define EPIC_SR_INT11_DES_REG (EPIC_EUMBBAR + 0x10370)/* Sr. Int. Sr11 Vect*/
+#define EPIC_SR_INT12_VEC_REG (EPIC_EUMBBAR + 0x10380)/* Sr. Int. Sr12 Des */
+#define EPIC_SR_INT12_DES_REG (EPIC_EUMBBAR + 0x10390)/* Sr. Int. Sr12 Vect*/
+#define EPIC_SR_INT13_VEC_REG (EPIC_EUMBBAR + 0x103a0)/* Sr. Int. Sr13 Des */
+#define EPIC_SR_INT13_DES_REG (EPIC_EUMBBAR + 0x103b0)/* Sr. Int. Sr13 Vect*/
+#define EPIC_SR_INT14_VEC_REG (EPIC_EUMBBAR + 0x103c0)/* Sr. Int. Sr14 Des */
+#define EPIC_SR_INT14_DES_REG (EPIC_EUMBBAR + 0x103d0)/* Sr. Int. Sr14 Vect*/
+#define EPIC_SR_INT15_VEC_REG (EPIC_EUMBBAR + 0x103e0)/* Sr. Int. Sr15 Des */
+#define EPIC_SR_INT15_DES_REG (EPIC_EUMBBAR + 0x103f0)/* Sr. Int. Sr15 Vect*/
+
+#define EPIC_I2C_INT_VEC_REG  (EPIC_EUMBBAR + 0x11020)/* I2C Int. Vect Pri.*/
+#define EPIC_I2C_INT_DES_REG  (EPIC_EUMBBAR + 0x11030)/* I2C Int. Dest */
+#define EPIC_DMA0_INT_VEC_REG (EPIC_EUMBBAR + 0x11040)/* DMA0 Int. Vect Pri*/
+#define EPIC_DMA0_INT_DES_REG (EPIC_EUMBBAR + 0x11050)/* DMA0 Int. Dest */
+#define EPIC_DMA1_INT_VEC_REG (EPIC_EUMBBAR + 0x11060)/* DMA1 Int. Vect Pri*/
+#define EPIC_DMA1_INT_DES_REG (EPIC_EUMBBAR + 0x11070)/* DMA1 Int. Dest */
+#define EPIC_MSG_INT_VEC_REG  (EPIC_EUMBBAR + 0x110c0)/* Msg Int. Vect Pri*/
+#define EPIC_MSG_INT_DES_REG  (EPIC_EUMBBAR + 0x110d0)/* Msg Int. Dest  */
+
+#define EPIC_PROC_CTASK_PRI_REG (EPIC_EUMBBAR + 0x20080)/* Proc. current task*/
+#define EPIC_PROC_INT_ACK_REG (EPIC_EUMBBAR + 0x200a0)/* Int. acknowledge */
+#define EPIC_PROC_EOI_REG (EPIC_EUMBBAR + 0x200b0)/* End of interrupt */
+
+/* Error code */
+
+#define OK       0
+#define ERROR    -1
+
+/* function prototypes */
+
+void epicVendorId( unsigned int *step,
+       unsigned int *devId,
+       unsigned int *venId
+     );
+void epicFeatures( unsigned int *noIRQs,
+             unsigned int *noCPUs,
+       unsigned int *VerId );
+extern void epicInit( unsigned int IRQType, unsigned int clkRatio);
+ULONG sysEUMBBARRead ( ULONG regNum );
+void sysEUMBBARWrite ( ULONG regNum, ULONG regVal);
+extern void epicTmFrequencySet( unsigned int frq );
+extern unsigned int epicTmFrequencyGet(void);
+extern unsigned int epicTmBaseSet( ULONG srcAddr,
+                 unsigned int cnt,
+                 unsigned int inhibit );
+extern unsigned int epicTmBaseGet ( ULONG srcAddr, unsigned int *val );
+extern unsigned int epicTmCountGet( ULONG srcAddr, unsigned int *val );
+extern unsigned int epicTmInhibit( unsigned int timer );
+extern unsigned int epicTmEnable( ULONG srcAdr );
+extern void CoreExtIntEnable(void);  /* Enable 603e external interrupts */
+extern void CoreExtIntDisable(void); /* Disable 603e external interrupts */
+extern unsigned char epicIntTaskGet(void);
+extern void epicIntTaskSet( unsigned char val );
+extern unsigned int epicIntAck(void);
+extern void epicSprSet( unsigned int eumbbar, unsigned char );
+extern void epicConfigGet( unsigned int *clkRatio,
+               unsigned int *serEnable );
+extern void SrcVecTableInit(void);
+extern unsigned int  epicModeGet(void);
+extern void epicIntEnable(int Vect);
+extern void epicIntDisable(int Vect);
+extern int epicIntSourceConfig(int Vect, int Polarity, int Sense, int Prio);
+extern unsigned int epicIntAck(void);
+extern void epicEOI(void);
+extern int epicCurTaskPrioSet(int Vect);
+
+struct SrcVecTable
+    {
+     ULONG srcAddr;
+     char  srcName[40];
+    };
+
+#endif   /*  EPIC_H */
diff --git a/doc/README.TQM8260 b/doc/README.TQM8260
new file mode 100644
index 00000000000..7e03010aabd
--- /dev/null
+++ b/doc/README.TQM8260
@@ -0,0 +1,415 @@
+
+This file contains basic information on the port of U-Boot to TQM8260.
+All the changes fit in the common U-Boot infrastructure, providing a
+new TQM8260-specific entry in makefiles. To build U-Boot for TQM8260,
+type "make TQM8260_config", edit the "include/config_TQM8260.h" file
+if necessary, then type "make".
+
+
+Common file modifications:
+--------------------------
+
+The following common files have been modified by this project:
+(starting from the ppcboot-0.9.3/ directory)
+
+MAKEALL			- TQM8260 entry added
+Makefile		- TQM8260_config entry added
+cpu/mpc8260/Makefile	- soft_i2c.o module added
+cpu/mpc8260/ether_scc.c	- TQM8260-specific definitions added, an obvious
+			  bug fixed (fcr -> scr)
+cpu/mpc8260/ether_fcc.c	- TQM8260-specific definitions added
+include/flash.h		- added definitions for the AM29LV640D Flash chip
+
+
+New files:
+----------
+
+The following new files have been added by this project:
+(starting from the ppcboot-0.9.3/ directory)
+
+board/tqm8260/		  - board-specific directory
+board/tqm8260/Makefile	  - board-specific makefile
+board/tqm8260/config.mk	  - config file
+board/tqm8260/flash.c	  - flash driver (for AM29LV640D)
+board/tqm8260/ppcboot.lds - linker script
+board/tqm8260/tqm8260.c	  - ioport and memory initialization
+cpu/mpc8260/soft_i2c.c	  - software i2c EEPROM driver
+include/config_TQM8260.h  - main configuration file
+
+
+New configuration options:
+--------------------------
+
+CONFIG_TQM8260
+
+	Main board-specific option (should be defined for TQM8260).
+
+CONFIG_82xx_CONS_SMC1
+
+	If defined, SMC1 will be used as the console
+
+CONFIG_82xx_CONS_SMC2
+
+	If defined, SMC2 will be used as the console
+
+CFG_INIT_LOCAL_SDRAM
+
+	If defined, the SDRAM on the local bus will be initialized and
+	mapped at BR2.
+
+
+Acceptance criteria tests:
+--------------------------
+
+The following tests have been conducted to validate the port of U-Boot
+to TQM8260:
+
+1. Operation on serial console:
+
+With the CONFIG_82xx_CONS_SMC1 option defined in the main configuration file,
+the U-Boot output appeared on the serial terminal connected to COM1 as
+follows:
+
+------------------------------------------------------------------------------
+=> help
+go      - start application at address 'addr'
+run     - run commands in an environment variable
+bootm   - boot application image from memory
+bootp   - boot image via network using BootP/TFTP protocol
+tftpboot- boot image via network using TFTP protocol
+               and env variables ipaddr and serverip
+rarpboot- boot image via network using RARP/TFTP protocol
+bootd   - boot default, i.e., run 'bootcmd'
+loads   - load S-Record file over serial line
+loadb   - load binary file over serial line (kermit mode)
+md      - memory display
+mm      - memory modify (auto-incrementing)
+nm      - memory modify (constant address)
+mw      - memory write (fill)
+cp      - memory copy
+cmp     - memory compare
+crc32   - checksum calculation
+base    - print or set address offset
+printenv- print environment variables
+setenv  - set environment variables
+saveenv - save environment variables to persistent storage
+protect - enable or disable FLASH write protection
+erase   - erase FLASH memory
+flinfo  - print FLASH memory information
+bdinfo  - print Board Info structure
+iminfo  - print header information for application image
+coninfo - print console devices and informations
+eeprom  - EEPROM sub-system
+loop    - infinite loop on address range
+mtest   - simple RAM test
+icache  - enable or disable instruction cache
+dcache  - enable or disable data cache
+reset   - Perform RESET of the CPU
+echo    - echo args to console
+version - print monitor version
+help    - print online help
+?       - alias for 'help'
+=>
+------------------------------------------------------------------------------
+
+
+2. Flash driver operation
+
+The following sequence was performed to test the "flinfo" command:
+
+------------------------------------------------------------------------------
+=> flinfo
+
+Bank # 1: AMD 29LV640D (64 M, uniform sector)
+  Size: 32 MB in 128 Sectors
+  Sector Start Addresses:
+    40000000      40040000 (RO) 40080000      400C0000      40100000
+    40140000      40180000      401C0000      40200000      40240000
+    40280000      402C0000      40300000      40340000      40380000
+    403C0000      40400000      40440000      40480000      404C0000
+    40500000      40540000      40580000      405C0000      40600000
+    40640000      40680000      406C0000      40700000      40740000
+    40780000      407C0000      40800000      40840000      40880000
+    408C0000      40900000      40940000      40980000      409C0000
+    40A00000      40A40000      40A80000      40AC0000      40B00000
+    40B40000      40B80000      40BC0000      40C00000      40C40000
+    40C80000      40CC0000      40D00000      40D40000      40D80000
+    40DC0000      40E00000      40E40000      40E80000      40EC0000
+    40F00000      40F40000      40F80000      40FC0000      41000000
+    41040000      41080000      410C0000      41100000      41140000
+    41180000      411C0000      41200000      41240000      41280000
+    412C0000      41300000      41340000      41380000      413C0000
+    41400000      41440000      41480000      414C0000      41500000
+    41540000      41580000      415C0000      41600000      41640000
+    41680000      416C0000      41700000      41740000      41780000
+    417C0000      41800000      41840000      41880000      418C0000
+    41900000      41940000      41980000      419C0000      41A00000
+    41A40000      41A80000      41AC0000      41B00000      41B40000
+    41B80000      41BC0000      41C00000      41C40000      41C80000
+    41CC0000      41D00000      41D40000      41D80000      41DC0000
+    41E00000      41E40000      41E80000      41EC0000      41F00000
+    41F40000      41F80000      41FC0000
+=>
+------------------------------------------------------------------------------
+
+
+The following sequence was performed to test the erase command:
+
+------------------------------------------------------------------------------
+=> cp 0 40080000 10
+Copy to Flash... done
+=> erase 40080000 400bffff
+Erase Flash from 0x40080000 to 0x400bffff
+.. done
+Erased 1 sectors
+=> md 40080000
+40080000: ffffffff ffffffff ffffffff ffffffff    ................
+40080010: ffffffff ffffffff ffffffff ffffffff    ................
+40080020: ffffffff ffffffff ffffffff ffffffff    ................
+40080030: ffffffff ffffffff ffffffff ffffffff    ................
+40080040: ffffffff ffffffff ffffffff ffffffff    ................
+40080050: ffffffff ffffffff ffffffff ffffffff    ................
+40080060: ffffffff ffffffff ffffffff ffffffff    ................
+40080070: ffffffff ffffffff ffffffff ffffffff    ................
+40080080: ffffffff ffffffff ffffffff ffffffff    ................
+40080090: ffffffff ffffffff ffffffff ffffffff    ................
+400800a0: ffffffff ffffffff ffffffff ffffffff    ................
+400800b0: ffffffff ffffffff ffffffff ffffffff    ................
+400800c0: ffffffff ffffffff ffffffff ffffffff    ................
+400800d0: ffffffff ffffffff ffffffff ffffffff    ................
+400800e0: ffffffff ffffffff ffffffff ffffffff    ................
+400800f0: ffffffff ffffffff ffffffff ffffffff    ................
+=> cp 0 40080000 10
+Copy to Flash... done
+=> erase 1:2
+Erase Flash Sectors 2-2 in Bank # 1
+.. done
+=> md 40080000
+40080000: ffffffff ffffffff ffffffff ffffffff    ................
+40080010: ffffffff ffffffff ffffffff ffffffff    ................
+40080020: ffffffff ffffffff ffffffff ffffffff    ................
+40080030: ffffffff ffffffff ffffffff ffffffff    ................
+40080040: ffffffff ffffffff ffffffff ffffffff    ................
+40080050: ffffffff ffffffff ffffffff ffffffff    ................
+40080060: ffffffff ffffffff ffffffff ffffffff    ................
+40080070: ffffffff ffffffff ffffffff ffffffff    ................
+40080080: ffffffff ffffffff ffffffff ffffffff    ................
+40080090: ffffffff ffffffff ffffffff ffffffff    ................
+400800a0: ffffffff ffffffff ffffffff ffffffff    ................
+400800b0: ffffffff ffffffff ffffffff ffffffff    ................
+400800c0: ffffffff ffffffff ffffffff ffffffff    ................
+400800d0: ffffffff ffffffff ffffffff ffffffff    ................
+400800e0: ffffffff ffffffff ffffffff ffffffff    ................
+400800f0: ffffffff ffffffff ffffffff ffffffff    ................
+=> cp 0 40080000 10
+Copy to Flash... done
+=> cp 0 400c0000 10
+Copy to Flash... done
+=> erase 1:2-3
+Erase Flash Sectors 2-3 in Bank # 1
+... done
+=> md 40080000
+40080000: ffffffff ffffffff ffffffff ffffffff    ................
+40080010: ffffffff ffffffff ffffffff ffffffff    ................
+40080020: ffffffff ffffffff ffffffff ffffffff    ................
+40080030: ffffffff ffffffff ffffffff ffffffff    ................
+40080040: ffffffff ffffffff ffffffff ffffffff    ................
+40080050: ffffffff ffffffff ffffffff ffffffff    ................
+40080060: ffffffff ffffffff ffffffff ffffffff    ................
+40080070: ffffffff ffffffff ffffffff ffffffff    ................
+40080080: ffffffff ffffffff ffffffff ffffffff    ................
+40080090: ffffffff ffffffff ffffffff ffffffff    ................
+400800a0: ffffffff ffffffff ffffffff ffffffff    ................
+400800b0: ffffffff ffffffff ffffffff ffffffff    ................
+400800c0: ffffffff ffffffff ffffffff ffffffff    ................
+400800d0: ffffffff ffffffff ffffffff ffffffff    ................
+400800e0: ffffffff ffffffff ffffffff ffffffff    ................
+400800f0: ffffffff ffffffff ffffffff ffffffff    ................
+=> md 400c0000
+400c0000: ffffffff ffffffff ffffffff ffffffff    ................
+400c0010: ffffffff ffffffff ffffffff ffffffff    ................
+400c0020: ffffffff ffffffff ffffffff ffffffff    ................
+400c0030: ffffffff ffffffff ffffffff ffffffff    ................
+400c0040: ffffffff ffffffff ffffffff ffffffff    ................
+400c0050: ffffffff ffffffff ffffffff ffffffff    ................
+400c0060: ffffffff ffffffff ffffffff ffffffff    ................
+400c0070: ffffffff ffffffff ffffffff ffffffff    ................
+400c0080: ffffffff ffffffff ffffffff ffffffff    ................
+400c0090: ffffffff ffffffff ffffffff ffffffff    ................
+400c00a0: ffffffff ffffffff ffffffff ffffffff    ................
+400c00b0: ffffffff ffffffff ffffffff ffffffff    ................
+400c00c0: ffffffff ffffffff ffffffff ffffffff    ................
+400c00d0: ffffffff ffffffff ffffffff ffffffff    ................
+400c00e0: ffffffff ffffffff ffffffff ffffffff    ................
+400c00f0: ffffffff ffffffff ffffffff ffffffff    ................
+=>
+------------------------------------------------------------------------------
+
+
+The following sequence was performed to test the Flash programming commands:
+
+------------------------------------------------------------------------------
+=> erase 40080000 400bffff
+Erase Flash from 0x40080000 to 0x400bffff
+.. done
+Erased 1 sectors
+=> cp 0 40080000 10
+Copy to Flash... done
+=> md 0
+00000000: 00000000 00000104 61100200 01000000    ........a.......
+00000010: 00000000 00000000 81140000 82000100    ................
+00000020: 01080000 00004000 22800000 00000600    ......@.".......
+00000030: 00200800 00000000 10000100 00008000    . ..............
+00000040: 00812000 00000200 00020000 80000000    .. .............
+00000050: 00028001 00001000 00040400 00000200    ................
+00000060: 20480000 00000000 20090000 00142000     H...... ..... .
+00000070: 00000000 00004000 24210000 10000000    ......@.$!......
+00000080: 02440002 10000000 00200008 00000000    .D....... ......
+00000090: 02440900 00000000 30a40000 00004400    .D......0.....D.
+000000a0: 04420800 00000000 00000040 00020000    .B.........@....
+000000b0: 05020000 00100000 00060000 00000000    ................
+000000c0: 00400000 00000000 00080000 00040000    .@..............
+000000d0: 10400000 00800004 00000000 00000200    .@..............
+000000e0: 80890000 00010004 00080000 00000020    ...............
+000000f0: 08000000 10000000 00010000 00000000    ................
+=> md 40080000
+40080000: 00000000 00000104 61100200 01000000    ........a.......
+40080010: 00000000 00000000 81140000 82000100    ................
+40080020: 01080000 00004000 22800000 00000600    ......@.".......
+40080030: 00200800 00000000 10000100 00008000    . ..............
+40080040: ffffffff ffffffff ffffffff ffffffff    ................
+40080050: ffffffff ffffffff ffffffff ffffffff    ................
+40080060: ffffffff ffffffff ffffffff ffffffff    ................
+40080070: ffffffff ffffffff ffffffff ffffffff    ................
+40080080: ffffffff ffffffff ffffffff ffffffff    ................
+40080090: ffffffff ffffffff ffffffff ffffffff    ................
+400800a0: ffffffff ffffffff ffffffff ffffffff    ................
+400800b0: ffffffff ffffffff ffffffff ffffffff    ................
+400800c0: ffffffff ffffffff ffffffff ffffffff    ................
+400800d0: ffffffff ffffffff ffffffff ffffffff    ................
+400800e0: ffffffff ffffffff ffffffff ffffffff    ................
+400800f0: ffffffff ffffffff ffffffff ffffffff    ................
+=>
+------------------------------------------------------------------------------
+
+
+The following sequence was performed to test storage of the environment
+variables in Flash:
+
+------------------------------------------------------------------------------
+=> setenv foo bar
+=> saveenv
+Un-Protected 1 sectors
+Erasing Flash...
+.. done
+Erased 1 sectors
+Saving Environment to Flash...
+Protected 1 sectors
+=> reset
+...
+=> printenv
+bootdelay=CONFIG_BOOTDELAY
+baudrate=9600
+ipaddr=192.168.4.7
+serverip=192.168.4.1
+ethaddr=66:55:44:33:22:11
+foo=bar
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 170/262140 bytes
+=>
+------------------------------------------------------------------------------
+
+
+The following sequence was performed to test image download and run over
+Ethernet interface (both interfaces were tested):
+
+------------------------------------------------------------------------------
+=> tftpboot 40000 hello_world.bin
+ARP broadcast 1
+TFTP from server 192.168.2.2; our IP address is 192.168.2.7
+Filename 'hello_world.bin'.
+Load address: 0x40000
+Loading: #############
+done
+Bytes transferred = 65912 (10178 hex)
+=> go 40004
+## Starting application at 0x00040004 ...
+Hello World
+argc = 1
+argv[0] = "40004"
+argv[1] = "<NULL>"
+Hit any key to exit ...
+
+## Application terminated, rc = 0x0
+=>
+------------------------------------------------------------------------------
+
+
+The following sequence was performed to test eeprom read/write commands:
+
+------------------------------------------------------------------------------
+=> md 40000
+00040000: 00018148 9421ffe0 7c0802a6 bf61000c    ...H.!..|....a..
+00040010: 90010024 48000005 7fc802a6 801effe8    ...$H...........
+00040020: 7fc0f214 7c7f1b78 813f004c 7c9c2378    ....|..x.?.L|.#x
+00040030: 807e8000 7cbd2b78 80090010 3b600000    .~..|.+x....;`..
+00040040: 7c0803a6 4e800021 813f004c 7f84e378    |...N..!.?.L...x
+00040050: 807e8004 80090010 7c0803a6 4e800021    .~......|...N..!
+00040060: 7c1be000 4181003c 80bd0000 813f004c    |...A..<.....?.L
+00040070: 3bbd0004 2c050000 40820008 80be8008    ;...,...@.......
+00040080: 80090010 7f64db78 807e800c 3b7b0001    .....d.x.~..;{..
+00040090: 7c0803a6 4e800021 7c1be000 4081ffcc    |...N..!|...@...
+000400a0: 813f004c 807e8010 80090010 7c0803a6    .?.L.~......|...
+000400b0: 4e800021 813f004c 80090004 7c0803a6    N..!.?.L....|...
+000400c0: 4e800021 2c030000 4182ffec 813f004c    N..!,...A....?.L
+000400d0: 80090000 7c0803a6 4e800021 813f004c    ....|...N..!.?.L
+000400e0: 807e8014 80090010 7c0803a6 4e800021    .~......|...N..!
+000400f0: 38600000 80010024 7c0803a6 bb61000c    8`.....$|....a..
+=> eeprom write 40000 0 40
+
+EEPROM write: addr 00040000  off 0000  count 64 ... done
+=> mw 50000 0 1000
+=> eeprom read 50000 0 40
+
+EEPROM read: addr 00050000  off 0000  count 64 ... done
+=> md 50000
+00050000: 00018148 9421ffe0 7c0802a6 bf61000c    ...H.!..|....a..
+00050010: 90010024 48000005 7fc802a6 801effe8    ...$H...........
+00050020: 7fc0f214 7c7f1b78 813f004c 7c9c2378    ....|..x.?.L|.#x
+00050030: 807e8000 7cbd2b78 80090010 3b600000    .~..|.+x....;`..
+00050040: 00000000 00000000 00000000 00000000    ................
+00050050: 00000000 00000000 00000000 00000000    ................
+00050060: 00000000 00000000 00000000 00000000    ................
+00050070: 00000000 00000000 00000000 00000000    ................
+00050080: 00000000 00000000 00000000 00000000    ................
+00050090: 00000000 00000000 00000000 00000000    ................
+000500a0: 00000000 00000000 00000000 00000000    ................
+000500b0: 00000000 00000000 00000000 00000000    ................
+000500c0: 00000000 00000000 00000000 00000000    ................
+000500d0: 00000000 00000000 00000000 00000000    ................
+000500e0: 00000000 00000000 00000000 00000000    ................
+000500f0: 00000000 00000000 00000000 00000000    ................
+=>
+------------------------------------------------------------------------------
+
+
+Patch per Mon, 06 Aug 2001 17:57:27:
+
+- upgraded Flash support (added support for the following chips:
+  AM29LV800T/B, AM29LV160T/B, AM29DL322T/B, AM29DL323T/B)
+- BCR tweakage for the 8260 bus mode
+- SIUMCR tweakage enabling the MI interrupt (IRQ7)
+
+To simplify switching between the bus modes, a new configuration
+option (CONFIG_BUSMODE_60x) has been added to the "config_TQM8260.h"
+file. If it is defined, BCR will be configured for the 60x mode,
+otherwise - for the 8260 mode.
+
+Concerning the SIUMCR modification: it's hard to predict whether it
+will induce any problems on the other (60x mode) board. However, the
+problems (if they appear) should be easy to notice - if the board
+does not boot, it's most likely caused by the DPPC configuration in
+SIUMCR.
diff --git a/doc/README.bedbug b/doc/README.bedbug
new file mode 100644
index 00000000000..ed7bc122ca7
--- /dev/null
+++ b/doc/README.bedbug
@@ -0,0 +1,89 @@
+BEDBUG Support for U-Boot
+--------------------------
+
+These changes implement the bedbug (emBEDded deBUGger) debugger in U-Boot.
+A specific implementation is made for the IBM405 processor but other flavors
+can be easily implemented.
+
+#####################
+### Modifications ###
+#####################
+
+./common/Makefile
+	Included cmd_bedbug.c and bedbug.c in the Makefile.
+
+./common/command.c
+	Added bedbug commands to command table.
+
+./common/board.c
+	Added call to initialize debugger on startup.
+
+./cpu/ppc4xx/Makefile
+	Added bedbug_405.c to the Makefile.
+
+./cpu/ppc4xx/start.S
+	Added code to handle the debug exception (0x2000) on the 405.
+	Also added code to handle critical exceptions since the debug
+	is treated as critical on the 405.
+
+./cpu/ppc4xx/traps.c
+	Added more detailed output for the program exception to tell
+	if it is an illegal instruction, privileged instruction or
+	a trap. Also added debug trap handler.
+
+./include/cmd_confdefs.h
+	Added definition of CFG_CMD_BEDBUG.
+
+./include/config_WALNUT405.h
+	Added CFG_CMD_BEDBUG to the CONFIG_COMMANDS for the WALNUT.
+
+./include/ppc_asm.tmpl
+	Added code to handle critical exceptions
+
+#################
+### New Stuff ###
+#################
+
+./include/bedbug/ppc.h
+./include/bedbug/regs.h
+./include/bedbug/bedbug.h
+./include/bedbug/elf.h		[obsoleted by new include/elf.h]
+./include/bedbug/tables.h
+./include/cmd_bedbug.h
+./common/cmd_bedbug.c
+./common/bedbug.c
+	Bedbug library includes code for assembling and disassembling
+	PowerPC instructions to/from memory as well as handling
+	hardware breakpoints and stepping through code.  These
+	routines are common to all PowerPC processors.
+
+./cpu/ppc4xx/bedbug_405.c
+	IBM PPC405 specific debugger routines.
+
+
+
+Bedbug support for the MPC860
+-----------------------------
+
+Changes:
+
+	common/cmd_bedbug.c
+		Added call to initialize 860 debugger.
+
+	cpu/mpc8xx/Makefile
+		Added new file "bedbug_860.c" to the makefile
+
+	cpu/mpc8xx/start.S
+		Added handler for InstructionBreakpoint (0xfd00)
+
+	cpu/mpc8xx/traps.c
+		Added new routine DebugException()
+
+	include/config_MBX.h
+		Added CFG_CMD_BEDBUG to CONFIG_COMMANDS define
+
+
+New Files:
+
+	cpu/mpc8xx/bedbug_860.c
+		CPU-specific routines for 860 debug registers.
diff --git a/doc/README.evb64260 b/doc/README.evb64260
new file mode 100644
index 00000000000..74211dea439
--- /dev/null
+++ b/doc/README.evb64260
@@ -0,0 +1,54 @@
+This file contains status information for the port of U-Boot to the
+Galileo Evaluation Board.
+
+Author: Josh Huber <huber@mclx.com>
+	Mission Critical Linux, Inc.
+
+The support for the Galileo Evaluation board is fairly minimal now.
+It's sufficient to boot Linux, but doesn't provide too much more than
+what's required to do this.
+
+Both DUART channels are supported (to use the second one, you have to
+modify the board -- see the schematics for where to solder on the
+devices module).  The ethernet ports are supported, and the MPSC is
+supported as a console driver. (keep in mind that the kernel has no
+support for this yet)
+
+There are still occaisonal lockups with the MPSC console driver due to
+(we think!) overrun problems.  If you're looking for something stable
+to use for Linux development, consider sticking with the DUART console
+for now.
+
+Automatic memory sizing mostly works.  We've had problems with some
+combinations of memory.  Please send us email if you're having trouble
+with respect to the memory detection.
+
+Right now, only the 512k boot flash is supported.  Support for the
+16MB flash on the devices module is forthcoming.  Right now the flash
+is stored at the 256k boundry in flash, wasting a whole sector (64k!)
+for environment data.  This isn't really a big deal since we're not
+using the 512k for anything else. (Just U-Boot and the environment)
+
+Finally, here is a sample output session:
+
+U-Boot 1.0.0-pre1 (Jun  6 2001 - 12:45:11)
+
+Initializing...
+  CPU:   MPC7400 (altivec enabled) v2.9
+  Board: EVB64260
+  DRAM:  256 MB
+  FLASH: 512 kB
+  In:    serial
+  Out:   serial
+  Err:   serial
+
+=>
+
+The default configuration should be correct for the evaluation board,
+as it's shipped from Galileo.  Keep in mind that the default baudrate
+is set to 38400, 8N1.
+
+Good luck, and make sure to send any bugreports to us (or the
+u-boot-users list).
+
+Josh
diff --git a/doc/README.mpc74xx b/doc/README.mpc74xx
new file mode 100644
index 00000000000..f81f1c2e890
--- /dev/null
+++ b/doc/README.mpc74xx
@@ -0,0 +1,22 @@
+This file contains status information for the port of U-Boot to the
+Motorola mpc74xx series of CPUs.
+
+Author: Josh Huber <huber@mclx.com>
+	Mission Critical Linux, Inc.
+
+Currently the support for these CPUs is pretty minimal, but enough to
+get things going.  (much like the support for the Galileo Eval Board)
+
+There is a framework in place to enable the L2 cache, and to program
+the BATs.  Currently, there are still problems with the code which
+sets up the L2 cache, so it's not enabled. (IMHO, it shouldn't be
+anyway).  Additionally, there is support for enabling the MMU, which
+we also don't do.  The BATs are programmed just for the benefit of
+jumping into Linux in a sane configuration.
+
+Most of the code was based on other cpus supported by U-Boot.
+
+If you find any errors in the CPU setup code, please send us a note.
+
+Thanks,
+Josh
diff --git a/doc/README.usb b/doc/README.usb
new file mode 100644
index 00000000000..41f76f4b7e4
--- /dev/null
+++ b/doc/README.usb
@@ -0,0 +1,80 @@
+/*
+ * (C) Copyright 2001
+ * Denis Peter, MPL AG Switzerland
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+USB Support for PIP405 and MIP405 (UHCI)
+========================================
+
+The USB support is implemented on the base of the UHCI Host
+controller.
+
+Currently supported are USB Hubs, USB Keyboards and USB Floppys.
+Tested with a TEAC Floppy TEAC FD-05PUB and Chicony KU-8933 Keyboard.
+
+How it works:
+-------------
+
+The USB (at least the USB UHCI) needs a frame list (4k), transfer
+descripor and queue headers which are all located in the main memory.
+The UHCI allocates every milisecond the PCI bus and reads the current
+frame pointer. This may cause to crash the OS during boot. So the USB
+_MUST_ be stopped during OS boot. This is the reason, why the USB is
+NOT automatically started during start-up. If someone needs the USB
+he has to start it and should therefore be aware that he had to stop
+it before booting the OS.
+
+For USB keyboards this can be done by a script which is automatically
+started after the U-Boot is up and running. To boot an OS with a an
+USB keyboard another script is necessary, which first disables the
+USB and then executes the boot command. If the boot command fails,
+the script can reenable the USB kbd.
+
+Common USB Commands:
+- usb start:
+- usb reset:	    (re)starts the USB. All USB devices will be
+		    initialized and a device tree is build for them.
+- usb tree:	    shows all USB devices in a tree like display
+- usb info [dev]:   shows all USB infos of the device dev, or of all
+		    the devices
+- usb stop [f]:	    stops the USB. If f==1 the USB will also stop if
+		    an USB keyboard is assigned as stdin. The stdin
+		    is then switched to serial input.
+Storage USB Commands:
+- usb scan:	    scans the USB for storage devices.The USB must be
+		    running for this command (usb start)
+- usb device [dev]: show or set current USB staorage device
+- usb part [dev]:   print partition table of one or all USB storage
+		    devices
+- usb read addr blk# cnt:
+		    read `cnt' blocks starting at block `blk#'to
+		    memory address `addr'
+- usbboot addr dev:part:
+		    boot from USB device
+
+Config Switches:
+----------------
+CFG_CMD_USB	    enables basic USB support and the usb command
+CONFIG_USB_UHCI	    defines the lowlevel part.A lowlevel part must be defined if
+		    using CFG_CMD_USB
+CONFIG_USB_KEYBOARD enables the USB Keyboard
+CONFIG_USB_STORAGE  enables the USB storage devices
diff --git a/include/asm-ppc/hymod.h b/include/asm-ppc/hymod.h
new file mode 100644
index 00000000000..b4179bf8f65
--- /dev/null
+++ b/include/asm-ppc/hymod.h
@@ -0,0 +1,289 @@
+#ifndef _ASM_HYMOD_H_
+#define _ASM_HYMOD_H_
+
+#include <linux/config.h>
+#ifdef CONFIG_8260
+#include <asm/iopin_8260.h>
+#endif
+
+/*
+ * hymod configuration data - passed by boot code via the board information
+ * structure (only U-Boot has support for this at the moment)
+ *
+ * there are three types of data passed up from the boot monitor. the first
+ * (type hymod_eeprom_t) is the eeprom data that was read off both the main
+ * (or mother) board and the mezzanine board (if any). this data defines how
+ * many Xilinx fpgas are on each board, and their types (among other things).
+ * the second type of data (type xlx_mmap_t, one per Xilinx fpga) defines where
+ * in the physical address space the various Xilinx fpga access regions have
+ * been mapped by the boot rom. the third type of data (type xlx_iopins_t,
+ * one per Xilinx fpga) defines which io port pins are connected to the various
+ * signals required to program a Xilinx fpga.
+ *
+ * A ram/flash "bank" refers to memory controlled by the same chip select.
+ *
+ * the eeprom contents are defined as in technical note #2 - basically,
+ * a header, zero or more records in no particular order, and a 32 bit crc
+ * a record is 1 or more type bytes, a length byte and "length" bytes.
+ */
+
+#define HYMOD_EEPROM_ID		0xAA	/* eeprom id byte */
+#define HYMOD_EEPROM_VER	1	/* eeprom contents version */
+#define HYMOD_EEPROM_SIZE	256	/* number of bytes in the eeprom */
+
+/* eeprom header */
+typedef
+    struct {
+	unsigned char id;		/* eeprom id byte */
+	unsigned char ver;		/* eeprom contents version number */
+	unsigned long len;		/* total # of bytes btw hdr and crc */
+    }
+hymod_eehdr_t;
+
+/* maximum number of bytes available for eeprom data records */
+#define HYMOD_EEPROM_MAXLEN	(HYMOD_EEPROM_SIZE \
+					- sizeof (hymod_eehdr_t) \
+					- sizeof (unsigned long))
+
+/* eeprom data record */
+typedef
+    union {
+	struct {
+	    unsigned char topbit:1;
+	    unsigned char type:7;
+	    unsigned char len;
+	    unsigned char data[1];	/* variable length */
+	} small;
+	struct {
+	    unsigned short topbit:1;
+	    unsigned short nxtbit:1;
+	    unsigned short type:14;
+	    unsigned short len;
+	    unsigned char data[1];	/* variable length */
+	} medium;
+	struct {
+	    unsigned long topbit:1;
+	    unsigned long nxtbit:1;
+	    unsigned long type:30;
+	    unsigned long len;
+	    unsigned char data[1];	/* variable length */
+	} large;
+    }
+hymod_eerec_t;
+
+#define HYMOD_EEOFF_MAIN	0x00	/* i2c addr offset for main eeprom */
+#define HYMOD_EEOFF_MEZZ	0x04	/* i2c addr offset for mezz eepomr */
+
+/* eeprom record types */
+#define HYMOD_EEREC_SERNO	1	/* serial number */
+#define HYMOD_EEREC_DATE	2	/* date */
+#define HYMOD_EEREC_BATCH	3	/* batch id */
+#define HYMOD_EEREC_TYPE	4	/* board type */
+#define HYMOD_EEREC_REV		5	/* revision number */
+#define HYMOD_EEREC_SDRAM	6	/* sdram sizes */
+#define HYMOD_EEREC_FLASH	7	/* flash sizes */
+#define HYMOD_EEREC_ZBT		8	/* zbt ram sizes */
+#define HYMOD_EEREC_XLXTYP	9	/* Xilinx fpga types */
+#define HYMOD_EEREC_XLXSPD	10	/* Xilinx fpga speeds */
+#define HYMOD_EEREC_XLXTMP	11	/* Xilinx fpga temperatures */
+#define HYMOD_EEREC_XLXGRD	12	/* Xilinx fpga grades */
+#define HYMOD_EEREC_CPUTYP	13	/* Motorola CPU type */
+#define HYMOD_EEREC_CPUSPD	14	/* CPU speed */
+#define HYMOD_EEREC_BUSSPD	15	/* bus speed */
+#define HYMOD_EEREC_CPMSPD	16	/* CPM speed */
+#define HYMOD_EEREC_HSTYPE	17	/* high-speed serial chip type */
+#define HYMOD_EEREC_HSCHIN	18	/* high-speed serial input channels */
+#define HYMOD_EEREC_HSCHOUT	19	/* high-speed serial output channels */
+
+/* some dimensions */
+#define HYMOD_MAX_BATCH		32	/* max no. of bytes in batch id */
+#define HYMOD_MAX_SDRAM		4	/* max sdram "banks" on any board */
+#define HYMOD_MAX_FLASH		4	/* max flash "banks" on any board */
+#define HYMOD_MAX_ZBT		16	/* max ZBT rams on any board */
+#define HYMOD_MAX_XLX		4	/* max Xilinx fpgas on any board */
+
+#define HYMOD_MAX_BYTES		16	/* enough to store any bytes array */
+
+/* board types */
+#define HYMOD_BDTYPE_NONE	0	/* information not present */
+#define HYMOD_BDTYPE_IO		1	/* I/O main board */
+#define HYMOD_BDTYPE_CLP	2	/* CLP main board */
+#define HYMOD_BDTYPE_DSP	3	/* DSP main board */
+#define HYMOD_BDTYPE_INPUT	4	/* video input mezzanine board */
+#define HYMOD_BDTYPE_ALTINPUT	5	/* video input mezzanine board */
+#define HYMOD_BDTYPE_DISPLAY	6	/* video display mezzanine board */
+#define HYMOD_BDTYPE_MAX	7	/* first invalid value */
+
+/* Xilinx fpga types */
+#define HYMOD_XTYP_NONE		0	/* information not present */
+#define HYMOD_XTYP_XCV300E	1	/* Xilinx Virtex 300 */
+#define HYMOD_XTYP_XCV400E	2	/* Xilinx Virtex 400 */
+#define HYMOD_XTYP_XCV600E	3	/* Xilinx Virtex 600 */
+#define HYMOD_XTYP_MAX		4	/* first invalid value */
+
+/* Xilinx fpga speeds */
+#define HYMOD_XSPD_NONE		0	/* information not present */
+#define HYMOD_XSPD_SIX		1
+#define HYMOD_XSPD_SEVEN	2
+#define HYMOD_XSPD_EIGHT	3
+#define HYMOD_XSPD_MAX		4	/* first invalid value */
+
+/* Xilinx fpga temperatures */
+#define HYMOD_XTMP_NONE		0	/* information not present */
+#define HYMOD_XTMP_COM		1
+#define HYMOD_XTMP_IND		2
+#define HYMOD_XTMP_MAX		3	/* first invalid value */
+
+/* Xilinx fpga grades */
+#define HYMOD_XTMP_NONE		0	/* information not present */
+#define HYMOD_XTMP_NORMAL	1
+#define HYMOD_XTMP_ENGSAMP	2
+#define HYMOD_XTMP_MAX		3	/* first invalid value */
+
+/* CPU types */
+#define HYMOD_CPUTYPE_NONE	0	/* information not present */
+#define HYMOD_CPUTYPE_MPC8260	1	/* Motorola MPC8260 embedded powerpc */
+#define HYMOD_CPUTYPE_MAX	2	/* first invalid value */
+
+/* CPU/BUS/CPM clock speeds */
+#define HYMOD_CLKSPD_NONE	0	/* information not present */
+#define HYMOD_CLKSPD_33MHZ	1
+#define HYMOD_CLKSPD_66MHZ	2
+#define HYMOD_CLKSPD_100MHZ	3
+#define HYMOD_CLKSPD_133MHZ	4
+#define HYMOD_CLKSPD_166MHZ	5
+#define HYMOD_CLKSPD_200MHZ	6
+#define HYMOD_CLKSPD_MAX	7	/* first invalid value */
+
+/* high speed serial chip types */
+#define HYMOD_HSSTYPE_NONE	0	/* information not present */
+#define HYMOD_HSSTYPE_AMCC52064	1
+#define HYMOD_HSSTYPE_MAX	2	/* first invalid value */
+
+/* a date (yyyy-mm-dd) */
+typedef
+    struct {
+	unsigned short year;
+	unsigned char month;
+	unsigned char day;
+    }
+hymod_date_t;
+
+/* describes a Xilinx fpga */
+typedef
+    struct {
+	unsigned char type;		/* chip type */
+	unsigned char speed;		/* chip speed rating */
+	unsigned char temp;		/* chip temperature rating */
+	unsigned char grade;		/* chip grade */
+    }
+hymod_xlx_t;
+
+/* describes a Motorola embedded processor */
+typedef
+    struct {
+	unsigned char type;		/* CPU type */
+	unsigned char cpuspd;		/* speed of the PowerPC core */
+	unsigned char busspd;		/* speed of the system and 60x bus */
+	unsigned char cpmspd;		/* speed of the CPM co-processor */
+    }
+hymod_mpc_t;
+
+/* info about high-speed (1Gbit) serial interface */
+typedef
+    struct {
+	unsigned char type;		/* high-speed serial chip type */
+	unsigned char nchin;		/* number of input channels mounted */
+	unsigned char nchout;		/* number of output channels mounted */
+    }
+hymod_hss_t;
+
+/*
+ * this defines the contents of the serial eeprom that exists on every
+ * hymod board, including mezzanine boards (the serial eeprom will be
+ * faked for early development boards that don't have one)
+ */
+
+typedef
+    struct {
+	unsigned char ver;		/* eeprom contents version */
+	unsigned char bdtype;		/* board type */
+	unsigned char bdrev;		/* board revision */
+	unsigned char batchlen;		/* length of batch string below */
+	unsigned long serno;		/* serial number */
+	hymod_date_t date;		/* manufacture date */
+	unsigned char batch[32];	/* manufacturer specific batch id */
+	unsigned char nsdram;		/* # of ram "banks" */
+	unsigned char nflash;		/* # of flash "banks" */
+	unsigned char nzbt;		/* # of ZBT rams */
+	unsigned char nxlx;		/* # of Xilinx fpgas */
+	unsigned char sdramsz[HYMOD_MAX_SDRAM];	/* log2 of sdram size */
+	unsigned char flashsz[HYMOD_MAX_FLASH];	/* log2 of flash size */
+	unsigned char zbtsz[HYMOD_MAX_ZBT];	/* log2 of ZBT ram size */
+	hymod_xlx_t xlx[HYMOD_MAX_XLX];	/* Xilinx fpga info */
+	hymod_mpc_t mpc;		/* Motorola MPC CPU info */
+	hymod_hss_t hss;		/* high-speed serial info */
+    }
+hymod_eeprom_t;
+
+/*
+ * this defines a region in the processor's physical address space
+ */
+typedef
+    struct {
+	unsigned long exists:1;		/* 1 if the region exists, 0 if not */
+	unsigned long size:31;		/* size in bytes */
+	unsigned long base;		/* base address */
+    }
+xlx_prgn_t;
+
+/*
+ * this defines where the various Xilinx fpga access regions are mapped
+ * into the physical address space of the processor
+ */
+typedef
+    struct {
+	xlx_prgn_t prog;		/* program access region */
+	xlx_prgn_t reg;			/* register access region */
+	xlx_prgn_t port;		/* port access region */
+    }
+xlx_mmap_t;
+
+/*
+ * this defines which 8260 i/o port pins are connected to the various
+ * signals required for programming a Xilinx fpga
+ */
+typedef
+    struct {
+	iopin_t prog_pin;		/* assert for >= 300ns to program */
+	iopin_t init_pin;		/* goes high when fpga is cleared */
+	iopin_t done_pin;		/* goes high when program is done */
+	iopin_t enable_pin;		/* some fpgas need enabling */
+    }
+xlx_iopins_t;
+
+/* all info about one hymod board */
+typedef
+    struct {
+	unsigned char eeprom_valid:1;
+	hymod_eeprom_t eeprom;
+	xlx_mmap_t mmap[HYMOD_MAX_XLX];
+	xlx_iopins_t iopins[HYMOD_MAX_XLX];
+    }
+hymod_board_t;
+
+/*
+ * this defines the configuration information of a hymod board-set
+ * (main board + possible mezzanine board). In future, there may be
+ * more than one mezzanine board (stackable?) - if so, add a "mezz2"
+ * field, and so on... or make mezz an array?
+ */
+typedef
+    struct {
+	hymod_board_t main;		/* main board info */
+	hymod_board_t mezz;		/* mezzanine board info */
+	unsigned long crc;		/* ensures kernel and boot prom agree */
+    }
+hymod_conf_t;
+
+#endif /* _ASM_HYMOD_H_ */
diff --git a/include/cmd_kgdb.h b/include/cmd_kgdb.h
new file mode 100644
index 00000000000..945c54e8088
--- /dev/null
+++ b/include/cmd_kgdb.h
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2000
+ * Murray Jensen <Murray.Jensen@cmst.csiro.au> and
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * KGDB support
+ */
+#ifndef	_CMD_KGDB_H
+#define	_CMD_KGDB_H
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CMD_TBL_KGDB	MK_CMD_TBL_ENTRY(				\
+	"kgdb",	4,	CFG_MAXARGS,	1,	do_kgdb,		\
+	"kgdb    - enter gdb remote debug mode\n",			\
+	"[arg0 arg1 .. argN]\n"						\
+	"    - executes a breakpoint so that kgdb mode is\n"		\
+	"      entered via the exception handler. To return\n"		\
+	"      to the monitor, the remote gdb debugger must\n"		\
+	"      execute a \"continue\" or \"quit\" command.\n"		\
+	"\n"								\
+	"      if a program is loaded by the remote gdb, any args\n"	\
+	"      passed to the kgdb command are given to the loaded\n"	\
+	"      program if it is executed (see the \"hello_world\"\n"	\
+	"      example program in the U-Boot examples directory)."	\
+),
+
+int do_kgdb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+#else
+#define CMD_TBL_KGDB
+#endif
+
+#endif	/* _CMD_KGDB_H */
diff --git a/include/common.h b/include/common.h
new file mode 100644
index 00000000000..49ab97ce94a
--- /dev/null
+++ b/include/common.h
@@ -0,0 +1,428 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __COMMON_H_
+#define __COMMON_H_	1
+
+#undef	_LINUX_CONFIG_H
+#define _LINUX_CONFIG_H 1	/* avoid reading Linux autoconf.h file	*/
+
+typedef unsigned char		uchar;
+typedef volatile unsigned long	vu_long;
+typedef volatile unsigned short	vu_short;
+typedef volatile unsigned char	vu_char;
+
+#include <config.h>
+#include <linux/bitops.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <asm/ptrace.h>
+#include <stdarg.h>
+#if defined(CONFIG_PCI) && defined(CONFIG_440)
+#include <pci.h>
+#endif
+#ifdef	CONFIG_8xx
+#include <asm/8xx_immap.h>
+#elif defined(CONFIG_8260)
+#include <asm/immap_8260.h>
+#endif
+#ifdef	CONFIG_4xx
+#include <ppc4xx.h>
+#endif
+#ifdef CONFIG_HYMOD
+#include <asm/hymod.h>
+#endif
+#ifdef CONFIG_ARM
+#define asmlinkage	/* nothing */
+#endif
+
+#include <part.h>
+#include <flash.h>
+#include <image.h>
+
+#ifdef	DEBUG
+#define debug(fmt,args...)	printf (fmt ,##args)
+#else
+#define debug(fmt,args...)
+#endif	/* DEBUG */
+
+typedef	void (interrupt_handler_t)(void *);
+
+#include <asm/u-boot.h>	/* boot information for Linux kernel */
+#include <asm/global_data.h>	/* global data used for startup functions */
+
+/* enable common handling for all TQM8xxL boards */
+#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L) || \
+    defined(CONFIG_TQM855L) || defined(CONFIG_TQM860L)
+# ifndef CONFIG_TQM8xxL
+#  define CONFIG_TQM8xxL
+# endif
+#endif
+
+
+/*
+ * Function Prototypes
+ */
+
+#if CONFIG_SERIAL_SOFTWARE_FIFO
+void	serial_buffered_init (void);
+void	serial_buffered_putc (const char);
+void	serial_buffered_puts (const char *);
+int	serial_buffered_getc (void);
+int	serial_buffered_tstc (void);
+#endif /* CONFIG_SERIAL_SOFTWARE_FIFO */
+
+void	hang	      (void) __attribute__ ((noreturn));
+
+/* */
+long int initdram (int);
+int	display_options	(void);
+void	print_size (ulong, const char *);
+
+/* common/main.c */
+void	main_loop	(void);
+int	run_command	(const char *cmd, int flag);
+int	readline	(const char *const prompt);
+void	reset_cmd_timeout(void);
+
+/* common/board.c */
+void	board_init_f  (ulong);
+void	board_init_r  (gd_t *, ulong);
+int	checkboard    (void);
+int	checkflash    (void);
+int	checkdram     (void);
+char *	strmhz(char *buf, long hz);
+int	last_stage_init(void);
+
+/* common/flash.c */
+void flash_perror (int);
+
+/* common/cmd_bootm.c */
+void print_image_hdr (image_header_t *hdr);
+
+extern ulong load_addr;		/* Default Load Address	*/
+
+/* common/cmd_nvedit.c */
+int	env_init     (void);
+void	env_relocate (void);
+char 	*getenv      (uchar *);
+int	getenv_r     (uchar *name, uchar *buf, unsigned len);
+int	saveenv      (void);
+#ifdef CONFIG_PPC		/* ARM version to be fixed! */
+void inline setenv   (char *, char *);
+#endif /* CONFIG_PPC */
+#ifdef CONFIG_ARM
+# include <asm/u-boot-arm.h>	/* ARM version to be fixed! */
+#endif /* CONFIG_ARM */
+
+void    pci_init      (void);
+void    pciinfo       (int, int);
+
+#if defined(CONFIG_PCI) && defined(CONFIG_440)
+#   if defined(CFG_PCI_PRE_INIT)
+    int    pci_pre_init        (struct pci_controller * );
+#   endif
+#   if defined(CFG_PCI_TARGET_INIT)
+	void    pci_target_init      (struct pci_controller *);
+#   endif
+#   if defined(CFG_PCI_MASTER_INIT)
+	void    pci_master_init      (struct pci_controller *);
+#   endif
+    int     is_pci_host         (struct pci_controller *);
+#endif
+
+int	misc_init_f   (void);
+int	misc_init_r   (void);
+
+/* $(BOARD)/$(BOARD).c */
+void	reset_phy     (void);
+
+/* $(BOARD)/eeprom.c */
+void eeprom_init  (void);
+int  eeprom_read  (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+int  eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+#ifdef CONFIG_LWMON
+extern uchar pic_read  (uchar reg);
+extern void  pic_write (uchar reg, uchar val);
+#endif
+
+/*
+ * Set this up regardless of board
+ * type, to prevent errors.
+ */
+#if defined(CONFIG_SPI) || !defined(CFG_I2C_EEPROM_ADDR)
+# define CFG_DEF_EEPROM_ADDR 0
+#else
+# define CFG_DEF_EEPROM_ADDR CFG_I2C_EEPROM_ADDR
+#endif /* CONFIG_SPI || !defined(CFG_I2C_EEPROM_ADDR) */
+
+#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM)
+extern void spi_init_f (void);
+extern void spi_init_r (void);
+extern ssize_t spi_read  (uchar *, int, uchar *, int);
+extern ssize_t spi_write (uchar *, int, uchar *, int);
+#endif
+
+#ifdef CONFIG_RPXCLASSIC
+void rpxclassic_init (void);
+#endif
+
+#ifdef CONFIG_MBX
+/* $(BOARD)/mbx8xx.c */
+void	mbx_init (void);
+void	board_serial_init (void);
+void	board_ether_init (void);
+#endif
+
+#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_MBX) || defined(CONFIG_IAD210)
+void	board_get_enetaddr (uchar *addr);
+#endif
+
+#ifdef CONFIG_HERMES
+/* $(BOARD)/hermes.c */
+void hermes_start_lxt980 (int speed);
+#endif
+
+#ifdef CONFIG_EVB64260
+void  evb64260_init(void);
+void  debug_led(int, int);
+void  display_mem_map(void);
+void  perform_soft_reset(void);
+#endif
+
+void	load_sernum_ethaddr (void);
+
+/* $(BOARD)/$(BOARD).c */
+int board_pre_init (void);
+int board_postclk_init (void); /* after clocks/timebase, before env/serial */
+void board_poweroff (void);
+
+#if defined(CFG_DRAM_TEST)
+int testdram(void);
+#endif /* CFG_DRAM_TEST */
+
+/* $(CPU)/start.S */
+#ifdef	CONFIG_8xx
+uint	get_immr      (uint);
+#endif
+uint	get_pvr	      (void);
+uint	rd_ic_cst     (void);
+void	wr_ic_cst     (uint);
+void	wr_ic_adr     (uint);
+uint	rd_dc_cst     (void);
+void	wr_dc_cst     (uint);
+void	wr_dc_adr     (uint);
+int	icache_status (void);
+void	icache_enable (void);
+void	icache_disable(void);
+int	dcache_status (void);
+void	dcache_enable (void);
+void	dcache_disable(void);
+void	relocate_code (ulong, gd_t *, ulong);
+ulong	get_endaddr   (void);
+void	trap_init     (ulong);
+#if defined (CONFIG_4xx)	|| \
+    defined (CONFIG_74xx_7xx)	|| \
+    defined (CONFIG_74x)	|| \
+    defined (CONFIG_75x)	|| \
+    defined (CONFIG_74xx)
+unsigned char   in8(unsigned int);
+void            out8(unsigned int, unsigned char);
+unsigned short  in16(unsigned int);
+unsigned short  in16r(unsigned int);
+void            out16(unsigned int, unsigned short value);
+void            out16r(unsigned int, unsigned short value);
+unsigned long   in32(unsigned int);
+unsigned long   in32r(unsigned int);
+void            out32(unsigned int, unsigned long value);
+void            out32r(unsigned int, unsigned long value);
+void            ppcDcbf(unsigned long value);
+void            ppcDcbi(unsigned long value);
+void            ppcSync(void);
+#endif
+
+/* $(CPU)/cpu.c */
+int	checkcpu      (void);
+int	checkicache   (void);
+int	checkdcache   (void);
+void	upmconfig     (unsigned int, unsigned int *, unsigned int);
+ulong	get_tbclk     (void);
+
+/* $(CPU)/serial.c */
+int	serial_init   (void);
+void	serial_setbrg (void);
+void	serial_putc   (const char);
+void	serial_puts   (const char *);
+void	serial_addr   (unsigned int);
+int	serial_getc   (void);
+int	serial_tstc   (void);
+
+/* $(CPU)/speed.c */
+int	get_clocks (void);
+#if defined(CONFIG_8260)
+int	prt_8260_clks (void);
+#endif
+#ifdef CONFIG_4xx
+ulong	get_OPB_freq (void);
+ulong	get_PCI_freq (void);
+#endif
+#if defined(CONFIG_S3C2400) || defined(CONFIG_S3C2410)
+ulong	get_FCLK (void);
+ulong	get_HCLK (void);
+ulong	get_PCLK (void);
+ulong	get_UCLK (void);
+#endif
+ulong	get_bus_freq  (ulong);
+
+#if defined(CONFIG_4xx) || defined(CONFIG_IOP480)
+#  if defined(CONFIG_440)
+    typedef PPC440_SYS_INFO sys_info_t;
+#  else
+    typedef PPC405_SYS_INFO sys_info_t;
+#  endif
+void    get_sys_info  ( sys_info_t * );
+#endif
+
+/* $(CPU)/cpu_init.c */
+#if defined(CONFIG_8xx) || defined(CONFIG_8260)
+void	cpu_init_f    (volatile immap_t *immr);
+#endif
+#ifdef	CONFIG_4xx
+void	cpu_init_f    (void);
+#endif
+int	cpu_init_r    (void);
+#if defined(CONFIG_8260)
+int	prt_8260_rsr  (void);
+#endif
+
+/* $(CPU)/interrupts.c */
+int	interrupt_init     (void);
+void	timer_interrupt    (struct pt_regs *);
+void	external_interrupt (struct pt_regs *);
+void	irq_install_handler(int, interrupt_handler_t *, void *);
+void	irq_free_handler   (int);
+void	reset_timer	   (void);
+ulong	get_timer	   (ulong base);
+void	set_timer	   (ulong t);
+void	enable_interrupts  (void);
+int	disable_interrupts (void);
+
+/* $(CPU)/.../commproc.c */
+int	dpram_init (void);
+uint	dpram_base(void);
+uint	dpram_base_align(uint align);
+uint	dpram_alloc(uint size);
+uint	dpram_alloc_align(uint size,uint align);
+void	post_word_store (ulong);
+ulong	post_word_load (void);
+
+/* $(CPU)/.../<eth> */
+void mii_init (void);
+
+/* $(CPU)/.../lcd.c */
+ulong	lcd_setmem (ulong);
+
+/* $(CPU)/.../vfd.c */
+ulong	vfd_setmem (ulong);
+
+/* $(CPU)/.../video.c */
+ulong	video_setmem (ulong);
+
+/* ppc/cache.c */
+void	flush_cache   (unsigned long, unsigned long);
+
+/* ppc/ticks.S */
+unsigned long long get_ticks(void);
+void	wait_ticks    (unsigned long);
+
+/* ppc/time.c */
+void	udelay	      (unsigned long);
+ulong	usec2ticks    (unsigned long usec);
+ulong	ticks2usec    (unsigned long ticks);
+int	init_timebase (void);
+
+/* ppc/vsprintf.c */
+ulong	simple_strtoul(const char *cp,char **endp,unsigned int base);
+long	simple_strtol(const char *cp,char **endp,unsigned int base);
+void	panic(const char *fmt, ...);
+int	sprintf(char * buf, const char *fmt, ...);
+int 	vsprintf(char *buf, const char *fmt, va_list args);
+
+/* ppc/crc32.c */
+ulong crc32 (ulong, const unsigned char *, uint);
+ulong crc32_no_comp (ulong, const unsigned char *, uint);
+
+/* common/console.c */
+extern void **syscall_tbl;
+
+int	console_init_f(void);	/* Before relocation; uses the serial  stuff	*/
+int	console_init_r(void);	/* After  relocation; uses the console stuff	*/
+int	console_assign (int file, char *devname);	/* Assign the console	*/
+int	ctrlc (void);
+int	had_ctrlc (void);	/* have we had a Control-C since last clear? */
+void	clear_ctrlc (void);	/* clear the Control-C condition */
+int	disable_ctrlc (int);	/* 1 to disable, 0 to enable Control-C detect */
+
+/*
+ * STDIO based functions (can always be used)
+ */
+
+/* serial stuff */
+void	serial_printf (const char *fmt, ...);
+
+/* stdin */
+int	getc(void);
+int	tstc(void);
+
+/* stdout */
+void	putc(const char c);
+void	puts(const char *s);
+void	printf(const char *fmt, ...);
+
+/* stderr */
+#define eputc(c)		fputc(stderr, c)
+#define eputs(s)		fputs(stderr, s)
+#define eprintf(fmt,args...)	fprintf(stderr,fmt ,##args)
+
+/*
+ * FILE based functions (can only be used AFTER relocation!)
+ */
+
+#define stdin		0
+#define stdout		1
+#define stderr		2
+#define MAX_FILES	3
+
+void	fprintf(int file, const char *fmt, ...);
+void	fputs(int file, const char *s);
+void	fputc(int file, const char c);
+int	ftstc(int file);
+int	fgetc(int file);
+
+int	pcmcia_init (void);
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void	show_boot_progress (int status);
+#endif
+
+#endif	/* __COMMON_H_ */
diff --git a/include/configs/BAB7xx.h b/include/configs/BAB7xx.h
new file mode 100644
index 00000000000..d312e6b5570
--- /dev/null
+++ b/include/configs/BAB7xx.h
@@ -0,0 +1,452 @@
+/*
+ * (C) Copyright 2002 ELTEC Elektronik AG
+ * Frank Gottschling <fgottschling@eltec.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/processor.h>
+
+#undef  DEBUG
+#define GTREGREAD(x) 0xffffffff         /* needed for debug */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+/* these hardware addresses are pretty bogus, please change them to
+   suit your needs */
+
+/* first ethernet */
+#define CONFIG_ETHADDR          00:00:5b:ee:de:ad
+
+#define CONFIG_IPADDR           192.168.0.105
+#define CONFIG_SERVERIP         192.168.0.100
+
+#define CONFIG_BAB7xx           1       /* this is an BAB740/BAB750 board */
+
+#define CONFIG_BAUDRATE         9600    /* console baudrate */
+
+#undef  CONFIG_WATCHDOG
+
+#define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#undef  CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND                                  \
+    "bootp 1000000; "                                       \
+    "setenv bootargs root=ramfs console=ttyS00,9600 "       \
+    "ip=$(ipaddr):$(serverip):$(rootpath):$(gatewayip):"    \
+    "$(netmask):$(hostname):eth0:none; "                    \
+    "bootm"
+
+#define CONFIG_LOADS_ECHO       0       /* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE           /* allow baudrate changes */
+
+#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS         (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 |\
+                                 CFG_CMD_SCSI   | CFG_CMD_IDE | CFG_CMD_DATE  |\
+                                 CFG_CMD_FDC    | CFG_CMD_ELF)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP                    /* undef to save memory */
+#define CFG_PROMPT              "=> "   /* Monitor Command Prompt */
+
+/*
+ * choose between COM1 and COM2 as serial console
+ */
+#define CONFIG_CONS_INDEX       1
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE              1024        /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE              256         /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS             16          /* max number of command args    */
+#define CFG_BARGSIZE            CFG_CBSIZE  /* Boot Argument Buffer Size    */
+
+#define CFG_MEMTEST_START       0x00000000  /* memtest works on    */
+#define CFG_MEMTEST_END         0x04000000  /* 0 ... 64 MB in DRAM    */
+
+#define CFG_LOAD_ADDR           0x1000000   /* default load address    */
+
+#define CFG_HZ                  1000        /* dec. freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+#define CFG_BOARD_ASM_INIT
+#define CONFIG_MISC_INIT_R
+
+/*
+ * Choose the address mapping scheme for the MPC106 mem controller.
+ * Default is mapping B (CHRP), set this define to choose mapping A (PReP).
+ */
+#define CFG_ADDRESS_MAP_A
+#ifdef  CFG_ADDRESS_MAP_A
+
+#define CFG_PCI_MEMORY_BUS      0x80000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x80000000
+
+#define CFG_PCI_MEM_BUS         0x00000000
+#define CFG_PCI_MEM_PHYS        0xc0000000
+#define CFG_PCI_MEM_SIZE        0x3f000000
+
+#define CFG_ISA_MEM_BUS         0
+#define CFG_ISA_MEM_PHYS        0
+#define CFG_ISA_MEM_SIZE        0
+
+#define CFG_PCI_IO_BUS          0x1000
+#define CFG_PCI_IO_PHYS         0x81000000
+#define CFG_PCI_IO_SIZE         0x01000000-CFG_PCI_IO_BUS
+
+#define CFG_ISA_IO_BUS          0x00000000
+#define CFG_ISA_IO_PHYS         0x80000000
+#define CFG_ISA_IO_SIZE         0x00800000
+
+#else
+
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x40000000
+
+#define CFG_PCI_MEM_BUS         0x80000000
+#define CFG_PCI_MEM_PHYS        0x80000000
+#define CFG_PCI_MEM_SIZE        0x7d000000
+
+#define CFG_ISA_MEM_BUS         0x00000000
+#define CFG_ISA_MEM_PHYS        0xfd000000
+#define CFG_ISA_MEM_SIZE        0x01000000
+
+#define CFG_PCI_IO_BUS          0x00800000
+#define CFG_PCI_IO_PHYS         0xfe800000
+#define CFG_PCI_IO_SIZE         0x00400000
+
+#define CFG_ISA_IO_BUS          0x00000000
+#define CFG_ISA_IO_PHYS         0xfe000000
+#define CFG_ISA_IO_SIZE         0x00800000
+
+#endif /*CFG_ADDRESS_MAP_A */
+
+#define CFG_60X_PCI_MEM_OFFSET  0x00000000
+
+/* driver defines FDC,IDE,... */
+#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS
+#define CFG_ISA_IO              CFG_ISA_IO_PHYS
+#define CFG_60X_PCI_IO_OFFSET   CFG_ISA_IO_PHYS
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE          0x00000000
+#define CFG_FLASH_BASE          0xfff00000
+
+/*
+ * Definitions for initial stack pointer and data area
+ */
+#define CFG_INIT_RAM_ADDR       0x00fd0000  /* above the memtest region */
+#define CFG_INIT_RAM_END        0x4000
+#define CFG_GBL_DATA_SIZE       64          /* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*
+ * Flash mapping/organization on the MPC10x.
+ */
+#define FLASH_BASE0_PRELIM      0xff800000
+#define FLASH_BASE1_PRELIM      0xffc00000
+
+#define CFG_MAX_FLASH_BANKS     2           /* max number of memory banks    */
+#define CFG_MAX_FLASH_SECT      67          /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT    120000      /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT    500         /* Timeout for Flash Write (in ms) */
+
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+
+#define CFG_MONITOR_BASE        CFG_FLASH_BASE
+#define CFG_MONITOR_LEN         0x40000     /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN          0x20000     /* Reserve 128 kB for malloc() */
+#undef  CFG_MEMTEST
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_OVERWRITE
+#define CFG_ENV_IS_IN_NVRAM     1           /* use NVRAM for environment vars */
+#define CFG_NVRAM_SIZE          0x1ff0      /* NVRAM size (8kB), we must protect the clock data (16 bytes) */
+#define CFG_ENV_SIZE            0x400       /* Size of Environment vars (1kB) */
+/*
+ * We store the environment and an image of revision eeprom in the upper part of the NVRAM. Thus,
+ * user applications can use the remaining space for other purposes.
+ */
+#define CFG_ENV_ADDR            (CFG_NVRAM_SIZE +0x10 -0x800)
+#define CFG_NV_SROM_COPY_ADDR   (CFG_NVRAM_SIZE +0x10 -0x400)
+#define CFG_NVRAM_ACCESS_ROUTINE            /* This board needs a special routine to access the NVRAM */
+#define CFG_SROM_SIZE           0x100       /* shadow of revision info is in nvram */
+
+/*
+ * Serial devices
+ */
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK         1843200
+#define CFG_NS16550_COM1        (CFG_ISA_IO + CFG_NS87308_UART1_BASE)
+#define CFG_NS16550_COM2        (CFG_ISA_IO + CFG_NS87308_UART2_BASE)
+
+/*
+ * PCI stuff
+ */
+#define CONFIG_PCI                                /* include pci support */
+#define CONFIG_PCI_PNP                            /* pci plug-and-play */
+#define CONFIG_PCI_HOST         PCI_HOST_AUTO
+#undef  CONFIG_PCI_SCAN_SHOW
+
+/*
+ * Video console (graphic: SMI LynxEM, keyboard: i8042)
+ */
+#define CONFIG_VIDEO
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SMI_LYNXEM
+#define CONFIG_I8042_KBD
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_TIME
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_CONSOLE_CURSOR
+#define CFG_CONSOLE_BLINK_COUNT         30000    /* approx. 2 HZ */
+
+/*
+ * IDE/SCSI globals
+ */
+#ifndef __ASSEMBLY__
+extern unsigned int    eltec_board;
+extern unsigned int    ata_reset_time;
+extern unsigned int    scsi_reset_time;
+extern unsigned short  scsi_dev_id;
+extern unsigned int    scsi_max_scsi_id;
+extern unsigned char   scsi_sym53c8xx_ccf;
+#endif
+
+/*
+ * ATAPI Support (experimental)
+ */
+#define CONFIG_ATAPI
+#define CFG_IDE_MAXBUS          1                       /* max. 2 IDE busses    */
+#define CFG_IDE_MAXDEVICE       (CFG_IDE_MAXBUS*2)      /* max. 2 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR       CFG_60X_PCI_IO_OFFSET   /* base address */
+#define CFG_ATA_IDE0_OFFSET     0x1F0                   /* default ide0 offste */
+#define CFG_ATA_IDE1_OFFSET     0x170                   /* default ide1 offset */
+#define CFG_ATA_DATA_OFFSET     0                       /* data reg offset    */
+#define CFG_ATA_REG_OFFSET      0                       /* reg offset */
+#define CFG_ATA_ALT_OFFSET      0x200                   /* alternate register offset */
+
+#define ATA_RESET_TIME          (ata_reset_time)
+
+#undef  CONFIG_IDE_PCMCIA                               /* no pcmcia interface required */
+#undef  CONFIG_IDE_LED                                  /* no led for ide supported */
+
+/*
+ * SCSI support (experimental) only SYM53C8xx supported
+ */
+#define CONFIG_SCSI_SYM53C8XX
+#define CONFIG_SCSI_DEV_ID      (scsi_dev_id)           /* 875 or 860 */
+#define CFG_SCSI_SYM53C8XX_CCF  (scsi_sym53c8xx_ccf)    /* value for none 40 mhz clocks */
+#define CFG_SCSI_MAX_LUN        8                       /* number of supported LUNs */
+#define CFG_SCSI_MAX_SCSI_ID    (scsi_max_scsi_id)      /* max SCSI ID (0-6) */
+#define CFG_SCSI_MAX_DEVICE     (15 * CFG_SCSI_MAX_LUN) /* max. Target devices */
+#define CFG_SCSI_SPIN_UP_TIME   (scsi_reset_time)
+
+/*
+ * Partion suppport
+ */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION
+
+/*
+ * Winbond Configuration
+ */
+#define CFG_WINBOND_83C553      1                       /* has a winbond bridge */
+#define CFG_USE_WINBOND_IDE     0                       /* use winbond 83c553 internal ide */
+#define CFG_WINBOND_ISA_CFG_ADDR    0x80005800          /* pci-isa bridge config addr */
+#define CFG_WINBOND_IDE_CFG_ADDR    0x80005900          /* ide config addr */
+
+/*
+ * NS87308 Configuration
+ */
+#define CFG_NS87308                    /* Nat Semi super-io cntr on ISA bus */
+#define CFG_NS87308_BADDR_10    1
+#define CFG_NS87308_DEVS        (CFG_NS87308_UART1   | \
+                                 CFG_NS87308_UART2   | \
+                                 CFG_NS87308_KBC1    | \
+                                 CFG_NS87308_MOUSE   | \
+                                 CFG_NS87308_FDC     | \
+                                 CFG_NS87308_RARP    | \
+                                 CFG_NS87308_GPIO    | \
+                                 CFG_NS87308_POWRMAN | \
+                                 CFG_NS87308_RTC_APC )
+
+#define CFG_NS87308_PS2MOD
+#define CFG_NS87308_GPIO_BASE   0x0220
+#define CFG_NS87308_PWMAN_BASE  0x0460
+#define CFG_NS87308_PMC2        0x00        /* SuperI/O clock source is 24MHz via X1 */
+
+/*
+ * set up the NVRAM access registers
+ * NVRAM's controlled by the configurable CS line from the 87308
+ */
+#define CFG_NS87308_CS0_BASE    0x0076
+#define CFG_NS87308_CS0_CONF    0x40
+#define CFG_NS87308_CS1_BASE    0x0070
+#define CFG_NS87308_CS1_CONF    0x1C
+#define CFG_NS87308_CS2_BASE    0x0071
+#define CFG_NS87308_CS2_CONF    0x1C
+
+#define CONFIG_RTC_MK48T59
+
+/*
+ * Initial BATs
+ */
+#if 1
+
+#define CFG_IBAT0L 0
+#define CFG_IBAT0U 0
+#define CFG_DBAT0L CFG_IBAT1L
+#define CFG_DBAT0U CFG_IBAT1U
+
+#define CFG_IBAT1L 0
+#define CFG_IBAT1U 0
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+#define CFG_IBAT2L 0
+#define CFG_IBAT2U 0
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+#define CFG_IBAT3L 0
+#define CFG_IBAT3U 0
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+#else
+
+/* SDRAM */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_RW)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT1L
+#define CFG_DBAT0U CFG_IBAT1U
+
+/* address range for flashes */
+#define CFG_IBAT1L (CFG_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U (CFG_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* ISA IO space */
+#define CFG_IBAT2L (CFG_ISA_IO | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (CFG_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+/* ISA memory space */
+#define CFG_IBAT3L (CFG_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (CFG_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+#endif
+
+/*
+ * Speed settings are board specific
+ */
+#ifndef __ASSEMBLY__
+extern  unsigned long           bab7xx_get_bus_freq (void);
+extern  unsigned long           bab7xx_get_gclk_freq (void);
+#endif
+#define CFG_BUS_HZ              bab7xx_get_bus_freq()
+#define CFG_BUS_CLK             CFG_BUS_HZ
+#define CFG_CPU_CLK             bab7xx_get_gclk_freq()
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ           (8 << 20)           /* Initial Memory map for Linux */
+
+/*
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE        32    /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT        5    /* log base 2 of the above value */
+#endif
+
+/*
+ * L2 Cache Configuration is board specific for BAB740/BAB750
+ * Init values read from revision srom.
+ */
+#undef  CFG_L2
+#define L2_INIT     (L2CR_L2SIZ_HM | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+                     L2CR_L2OH_5   | L2CR_L2CTL   | L2CR_L2WT)
+#define L2_ENABLE   (L2_INIT | L2CR_L2E)
+
+#define CFG_L2_BAB7xx
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD           0x01    /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM           0x02    /* Software reboot */
+
+
+#define CONFIG_NET_MULTI                /* Multi ethernet cards support */
+#define CONFIG_TULIP
+#define CONFIG_TULIP_SELECT_MEDIA
+
+#endif    /* __CONFIG_H */
diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h
new file mode 100644
index 00000000000..a3b12961b43
--- /dev/null
+++ b/include/configs/ELPPC.h
@@ -0,0 +1,338 @@
+/*
+ * (C) Copyright 2002 ELTEC Elektronik AG
+ * Frank Gottschling <fgottschling@eltec.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/processor.h>
+
+#undef  DEBUG
+#define GTREGREAD(x) 0xffffffff         /* needed for debug */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+/* these hardware addresses are pretty bogus, please change them to
+   suit your needs */
+
+/* first ethernet */
+#define CONFIG_ETHADDR          00:00:5b:ee:de:ad
+
+#define CONFIG_IPADDR           192.168.0.105
+#define CONFIG_SERVERIP         192.168.0.100
+
+#define CONFIG_ELPPC            1       /* this is an BAB740/BAB750 board */
+
+#define CONFIG_BAUDRATE         9600    /* console baudrate */
+
+#undef  CONFIG_WATCHDOG
+
+#define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#undef  CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND                                  \
+    "bootp 1000000; "                                       \
+    "setenv bootargs root=ramfs console=ttyS00,9600 "       \
+    "ip=$(ipaddr):$(serverip):$(rootpath):$(gatewayip):"    \
+    "$(netmask):$(hostname):eth0:none; "                    \
+    "bootm"
+
+#define CONFIG_LOADS_ECHO       0       /* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE           /* allow baudrate changes */
+
+#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS         (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP                    /* undef to save memory */
+#define CFG_PROMPT              "=> "   /* Monitor Command Prompt */
+
+/*
+ * choose between COM1 and COM2 as serial console
+ */
+#define CONFIG_CONS_INDEX       1
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE              1024        /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE              256         /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS             16          /* max number of command args    */
+#define CFG_BARGSIZE            CFG_CBSIZE  /* Boot Argument Buffer Size    */
+
+#define CFG_MEMTEST_START       0x00000000  /* memtest works on    */
+#define CFG_MEMTEST_END         0x04000000  /* 0 ... 64 MB in DRAM    */
+
+#define CFG_LOAD_ADDR           0x1000000   /* default load address    */
+
+#define CFG_HZ                  1000        /* dec. freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+#define CFG_BOARD_ASM_INIT
+#define CONFIG_MISC_INIT_R
+
+/*
+ * Address mapping scheme for the MPC107 mem controller is mapping B (CHRP)
+ */
+#undef  CFG_ADDRESS_MAP_A
+
+#define CFG_PCI_MEMORY_BUS      0x00000000
+#define CFG_PCI_MEMORY_PHYS     0x00000000
+#define CFG_PCI_MEMORY_SIZE     0x40000000
+
+#define CFG_PCI_MEM_BUS         0x80000000
+#define CFG_PCI_MEM_PHYS        0x80000000
+#define CFG_PCI_MEM_SIZE        0x7d000000
+
+#define CFG_ISA_MEM_BUS         0x00000000
+#define CFG_ISA_MEM_PHYS        0xfd000000
+#define CFG_ISA_MEM_SIZE        0x01000000
+
+#define CFG_PCI_IO_BUS          0x00800000
+#define CFG_PCI_IO_PHYS         0xfe800000
+#define CFG_PCI_IO_SIZE         0x00400000
+
+#define CFG_ISA_IO_BUS          0x00000000
+#define CFG_ISA_IO_PHYS         0xfe000000
+#define CFG_ISA_IO_SIZE         0x00800000
+
+/* driver defines FDC,IDE,... */
+#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS
+#define CFG_ISA_IO              CFG_ISA_IO_PHYS
+#define CFG_60X_PCI_IO_OFFSET   CFG_ISA_IO_PHYS
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE          0x00000000
+
+#define CFG_USR_LED_BASE        0x78000000
+#define CFG_NVRAM_BASE          0xff000000
+#define CFG_UART_BASE           0xff400000
+#define CFG_FLASH_BASE          0xfff00000
+
+#define MPC107_EUMB_ADDR        0xfce00000
+#define MPC107_EUMB_PI          0xfce41090
+#define MPC107_EUMB_GCR         0xfce41020
+#define MPC107_EUMB_IACKR       0xfce600a0
+#define MPC107_I2C_ADDR         0xfce03000
+
+/*
+ * Definitions for initial stack pointer and data area
+ */
+#define CFG_INIT_RAM_ADDR       0x00fd0000  /* above the memtest region */
+#define CFG_INIT_RAM_END        0x4000
+#define CFG_GBL_DATA_SIZE       64          /* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*
+ * Flash mapping/organization on the MPC10x.
+ */
+#define FLASH_BASE0_PRELIM      0xff800000
+#define FLASH_BASE1_PRELIM      0xffc00000
+
+#define CFG_MAX_FLASH_BANKS     2           /* max number of memory banks    */
+#define CFG_MAX_FLASH_SECT      67          /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT    120000      /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT    500         /* Timeout for Flash Write (in ms) */
+
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     2           /* ! second bank contains U-Boot */
+
+#define CFG_MONITOR_BASE        CFG_FLASH_BASE
+#define CFG_MONITOR_LEN         0x40000     /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN          0x20000     /* Reserve 128 kB for malloc() */
+#undef  CFG_MEMTEST
+
+/*
+ * Environment settings
+ */
+#define CONFIG_ENV_OVERWRITE
+#define CFG_ENV_IS_IN_NVRAM     1           /* use NVRAM for environment vars */
+#define CFG_NVRAM_SIZE          0x800       /* NVRAM size (2kB) */
+#define CFG_ENV_SIZE            0x400       /* Size of Environment vars (1kB) */
+#define CFG_ENV_ADDR            0x0
+#define CFG_ENV_MAP_ADRS        0xff000000
+#define CFG_NV_SROM_COPY_ADDR   (CFG_ENV_ADDR + CFG_ENV_SIZE)
+#define CFG_NVRAM_ACCESS_ROUTINE            /* only byte accsess alowed */
+#define CFG_SROM_SIZE           0x100       /* shadow of revision info is in nvram */
+
+/*
+ * Serial devices
+ */
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_CLK         24000000
+#define CFG_NS16550_COM1        (CFG_UART_BASE + 0)
+#define CFG_NS16550_COM2        (CFG_UART_BASE + 8)
+
+/*
+ * PCI stuff
+ */
+#define CONFIG_PCI                                /* include pci support */
+#define CONFIG_PCI_PNP                            /* pci plug-and-play */
+#define CONFIG_PCI_HOST         PCI_HOST_AUTO
+#undef  CONFIG_PCI_SCAN_SHOW
+
+/*
+ * Optional Video console (graphic: SMI LynxEM)
+ */
+#define CONFIG_VIDEO
+#define CONFIG_CFB_CONSOLE
+#define VIDEO_KBD_INIT_FCT    (simple_strtol (getenv("console"), NULL, 10))
+#define VIDEO_TSTC_FCT        serial_tstc
+#define VIDEO_GETC_FCT        serial_getc
+
+#define CONFIG_VIDEO_SMI_LYNXEM
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+
+/*
+ * Initial BATs
+ */
+#if 1
+
+#define CFG_IBAT0L 0
+#define CFG_IBAT0U 0
+#define CFG_DBAT0L CFG_IBAT1L
+#define CFG_DBAT0U CFG_IBAT1U
+
+#define CFG_IBAT1L 0
+#define CFG_IBAT1U 0
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+#define CFG_IBAT2L 0
+#define CFG_IBAT2U 0
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+#define CFG_IBAT3L 0
+#define CFG_IBAT3U 0
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+#else
+
+/* SDRAM */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_RW)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT1L
+#define CFG_DBAT0U CFG_IBAT1U
+
+/* address range for flashes */
+#define CFG_IBAT1L (CFG_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U (CFG_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* ISA IO space */
+#define CFG_IBAT2L (CFG_ISA_IO | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (CFG_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+/* ISA memory space */
+#define CFG_IBAT3L (CFG_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (CFG_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+#endif
+
+/*
+ * Speed settings are board specific
+ */
+#define CFG_BUS_HZ              100000000
+#define CFG_CPU_CLK             400000000
+#define CFG_BUS_CLK             CFG_BUS_HZ
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ           (8 << 20)           /* Initial Memory map for Linux */
+
+/*
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE        32    /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT        5    /* log base 2 of the above value */
+#endif
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+
+#define CFG_L2
+
+#if 1
+#define L2_INIT     0       /* cpu 750 CXe*/
+#else
+#define L2_INIT     (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+                     L2CR_L2OH_5   | L2CR_L2CTL | L2CR_L2WT)
+#endif
+#define L2_ENABLE   (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD           0x01    /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM           0x02    /* Software reboot */
+
+#define CONFIG_NET_MULTI        /* Multi ethernet cards support */
+#define CONFIG_EEPRO100
+#define CONFIG_EEPRO100_SROM_WRITE
+
+#endif    /* __CONFIG_H */
diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h
new file mode 100644
index 00000000000..9f6baf7fffc
--- /dev/null
+++ b/include/configs/ERIC.h
@@ -0,0 +1,372 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_ERIC		1	/* ...on a ERIC board	*/
+
+#define	CONFIG_BOARD_PRE_INIT	1	/* run board_pre_init() */
+
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
+
+#if 1
+#define CFG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars	*/
+#endif
+#if 0
+#define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
+#endif
+#if 0
+#define CFG_ENV_IS_IN_EEPROM	1	/* use I2C RTC X1240 for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars */
+#endif					/* total size of a X1240 is 2048 bytes */
+
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x57	/* X1240 has two I2C slave addresses, one for EEPROM */
+#define CFG_I2C_EEPROM_ADDR_LEN	2	/* address length for the eeprom */
+#define CONFIG_I2C_RTC		1	/* we have a Xicor X1240 RTC */
+#define CFG_I2C_RTC_ADDR	0x6F	/*                                and one for RTC */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#undef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_EEPROM
+#else
+#ifdef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_FLASH
+#undef CFG_ENV_IS_IN_EEPROM
+#else
+#ifdef CFG_ENV_IS_IN_EEPROM
+#undef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_FLASH
+#endif
+#endif
+#endif
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#if 1
+#define CONFIG_BOOTCOMMAND	"bootm ffc00000" /* autoboot command	*/
+#else
+#define CONFIG_BOOTCOMMAND	"bootp" /* autoboot command		*/
+#endif
+
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/nfs "	\
+				"nfsroot=192.168.1.2:/eric_root_devel "	\
+				"ip=192.168.1.22:192.168.1.2"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		1	/* PHY address			*/
+
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_ENV	| \
+				CFG_CMD_FLASH)
+
+/*
+ * #define CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | \
+ *				 CFG_CMD_KGDB | CFG_CMD_I2C | CFG_CMD_EEPROM | \
+ *				 CFG_CMD_ENV | CFG_CMD_FLASH)
+ */
+
+/* CFG_CMD_ENV est definie */
+/*	((CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_KGDB) & ~(CFG_CMD_ENV))
+ */
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#undef	CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	 CFG_EXT_SERIAL_CLOCK	 14318180
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE	\
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
+#undef  CONFIG_PCI_PNP			/* no pci plug-and-play         */
+                                        /* resource configuration       */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x1743	/* PCI Vendor ID: Peppercon AG	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: 405GP		*/
+#define CFG_PCI_PTM1LA	0xFFFC0000	/* point to flash		*/
+#define CFG_PCI_PTM1MS	0xFFFFF001	/* 4kB, enable hard-wired to 1	*/
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA	0x00000000	/* disabled			*/
+#define CFG_PCI_PTM2MS	0x00000000	/* disabled			*/
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * External peripheral base address
+ *-----------------------------------------------------------------------
+ */
+/*	Bank 0 - Flash/SRAM	       0xFF000000 16MB	16 Bit */
+/*	Bank 1 - NVRAM/RTC	       0xF0000000  1MB	 8 Bit */
+/*	Bank 2 - A/D converter	       0xF0100000  1MB	 8 Bit */
+/*	Bank 3 - Ethernet PHY Reset    0xF0200000  1MB	 8 Bit */
+/*	Bank 4 - PC-MIP PRSNT1#	       0xF0300000  1MB	 8 Bit */
+/*	Bank 5 - PC-MIP PRSNT2#	       0xF0400000  1MB	 8 Bit */
+/*	Bank 6 - CPU LED0	       0xF0500000  1MB	 8 Bit */
+/*	Bank 7 - CPU LED1	       0xF0600000  1MB	 8 Bit */
+
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 0 (Flash) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS0_AP	0x9B015480
+#define CS0_CR	0xFF87A000 /*  BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 1 (NVRAM/RTC) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS1_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS1_CR	0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+ /* ----------------------------------------------------------------------- */
+ /*  Memory Bank 2 (A/D converter) initialization */
+ /* ----------------------------------------------------------------------- */
+#define CS2_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS2_CR	0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 3 (Ethernet PHY Reset) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS3_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS3_CR	0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 4 (PC-MIP PRSNT1#) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS4_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS4_CR	0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 5 (PC-MIP PRSNT2#) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS5_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS5_CR	0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 6 (CPU LED0) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS6_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS6_CR	0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+/* ----------------------------------------------------------------------- */
+/*  Memory Bank 7 (CPU LED1) initialization */
+/* ----------------------------------------------------------------------- */
+#define CS7_AP	0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */
+#define CS7_CR	0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */
+
+#define CFG_NVRAM_REG_BASE_ADDR	 0xF0000000
+#define CFG_RTC_REG_BASE_ADDR	 (0xF0000000 + 0x7F8)
+#define CFG_ADC_REG_BASE_ADDR	 0xF0100000
+#define CFG_PHYRES_REG_BASE_ADDR 0xF0200000
+#define CFG_PRSNT1_REG_BASE_ADDR 0xF0300000
+#define CFG_PRSNT2_REG_BASE_ADDR 0xF0400000
+#define CFG_LED0_REG_BASE_ADDR	 0xF0500000
+#define CFG_LED1_REG_BASE_ADDR	 0xF0600000
+
+
+/*  SDRAM CONFIG */
+#define CFG_SDRAM_MANUALLY    1
+#define CFG_SDRAM_SINGLE_BANK 1
+
+#ifdef CFG_SDRAM_MANUALLY
+/*-----------------------------------------------------------------------
+ * Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2)
+ *----------------------------------------------------------------------*/
+#define MB0CF	0x00062001 /*  32MB @ 0 */
+/*-----------------------------------------------------------------------
+ * Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2)
+ *----------------------------------------------------------------------*/
+#ifdef CFG_SDRAM_SINGLE_BANK
+#define MB1CF	0x0 /*  0MB @ 32MB */
+#else
+#define MB1CF	0x02062001 /*  32MB @ 32MB */
+#endif
+/*-----------------------------------------------------------------------
+ * Set MB2CF for bank 2. off
+ *----------------------------------------------------------------------*/
+#define MB2CF	0x0 /*  0MB */
+/*-----------------------------------------------------------------------
+ * Set MB3CF for bank 3. off
+ *----------------------------------------------------------------------*/
+#define MB3CF	0x0 /*  0MB */
+
+#define SDTR_100    0x0086400D
+#define RTR_100     0x05F0
+#define SDTR_66     0x00854006	/* orig U-Boot-wallnut says 0x00854006 */
+#define RTR_66      0x03f8
+
+#endif   /* CFG_SDRAM_MANUALLY */
+
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		32
+#define CFG_FLASH_BASE		0xFF800000      /* 8 MByte Flash */
+#define CFG_MONITOR_BASE	0xFFFE0000      /* last 128kByte within Flash */
+/*#define CFG_MONITOR_LEN		(192 * 1024)*/	/* Reserve 196 kB for Monitor	*/
+#define CFG_MONITOR_LEN		(128 * 1024)	/* Reserve 128 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	64	/* max number of sectors on one chip	*/
+#define CFG_FLASH_16BIT		1	/* Rom 16 bit data bus			*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+/* BEG ENVIRONNEMENT FLASH */
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE       (128*1024)
+
+#if 0  /* force ENV to be NOT embedded */
+#define CFG_ENV_ADDR            0xfffa0000
+#else  /* force ENV to be embedded */
+#define	CFG_ENV_SIZE		(2 * 1024) /* Total Size of Environment Sector 2k */
+#define CFG_ENV_ADDR            (CFG_MONITOR_BASE + CFG_MONITOR_LEN - CFG_ENV_SIZE - 0x10) /* let space for reset vector */
+/* #define CFG_ENV_ADDR            (CFG_MONITOR_BASE)*/
+#define CFG_ENV_OFFSET          (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#endif
+
+#endif
+/* END ENVIRONNEMENT FLASH */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_NVRAM_BASE_ADDR	CFG_NVRAM_REG_BASE_ADDR	/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		0x7F8		/* NVRAM size 2kByte - 8 Byte for RTC */
+
+#ifdef CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_SIZE		0x7F8		/* Size of Environment vars	*/
+#define CFG_ENV_ADDR		\
+	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)	/* Env	*/
+#endif
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		8192	/* For IBM 405 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0xFF800000	/* FLASH bank #0 8MB 	*/
+#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
+
+
+/* Configuration Port location */
+/*  #define CONFIG_PORT_ADDR	0xF0000500 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x00df0000  /* inside of SDRAM		       */
+#define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ */
+#define SPD_EEPROM_ADDRESS      0x50
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */
diff --git a/include/configs/ETX094.h b/include/configs/ETX094.h
new file mode 100644
index 00000000000..9d7c8689c81
--- /dev/null
+++ b/include/configs/ETX094.h
@@ -0,0 +1,356 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC850		1	/* This is a MPC850 CPU		*/
+#define CONFIG_ETX094		1	/* ...on a ETX_094 board	*/
+
+#define	CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		57600
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#define CONFIG_BOARD_TYPES	1	/* support board types		*/
+
+#define	CONFIG_FLASH_16BIT		/* for board with 16bit wide flash	*/
+#undef	SB_ETX094			/* only for SB-Board with 16MB SDRAM 	*/
+#define	CONFIG_BOOTP_RANDOM_DELAY	/* graceful BOOTP recovery mode		*/
+
+#define CONFIG_ETHADDR 08:00:06:00:00:00
+
+#ifdef	CONFIG_ETHADDR
+#define CONFIG_OVERWRITE_ETHADDR_ONCE 1	/* default MAC can be overwritten once	*/
+#endif
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"bootp; "								\
+	"setenv bootargs root=/dev/ram rw ramdisk_size=4690 "			\
+	"U-Boot_version=U-Boot-1.0.x-Date "					\
+	"panic=1 "								\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; "	\
+	"bootm"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"bootp; "								\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(nfsip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; "	\
+	"bootm"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/
+
+#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0300000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0700000	/* 3 ... 7 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x40000000
+#ifdef	DEBUG
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#else
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#endif
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	35	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#ifdef CONFIG_FLASH_16BIT
+#define CFG_ENV_OFFSET		0x8000	/* Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x8000	/* Total Size of Environment Sector	*/
+#else
+#define CFG_ENV_OFFSET		0x8000	/* Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
+#define CFG_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
+#define CFG_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif	/* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CFG_SCCR	(SCCR_TBS     | \
+			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define	CFG_DER	0x2002000F*/
+#define CFG_DER	0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 1, CSNT = 0, SCY = 2, EHTR = 0	*/
+#define CFG_OR_TIMING_FLASH    (OR_ACS_DIV2 | OR_BI | \
+                               OR_SCY_2_CLK | OR_TRLX )
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+
+#ifdef CONFIG_FLASH_16BIT	/* 16 bit data port */
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16)
+#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16)
+#else				/* 32 bit data port */
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32)
+#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32)
+#endif	/* CONFIG_FLASH_16BIT */
+
+#define CFG_OR1_REMAP	CFG_OR0_REMAP
+#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
+#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA	23		/* start with divider for 100 MHz	*/
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_1X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_1X)
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/IP860.h b/include/configs/IP860.h
new file mode 100644
index 00000000000..6fa2d19c2fd
--- /dev/null
+++ b/include/configs/IP860.h
@@ -0,0 +1,459 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
+#define CONFIG_IP860		1	/* ...on a IP860 board		*/
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" \
+"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 $(filesize)\0"
+
+#define CONFIG_ETHADDR	00:30:bf:01:02:d2
+#define CONFIG_IPADDR	10.0.0.5
+#define CONFIG_SERVERIP	10.0.0.2
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND							\
+	"bootp; "								\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; "	\
+	"bootm"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+
+/* enable I2C and select the hardware/software driver */
+#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+
+# define CFG_I2C_SPEED		50000
+# define CFG_I2C_SLAVE		0xFE
+# define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
+# define CFG_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS	4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec */
+
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | \
+				 CFG_CMD_BEDBUG	| \
+				 CFG_CMD_I2C	| \
+				 CFG_CMD_EEPROM)
+
+#define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
+
+/*----------------------------------------------------------------------*/
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x00100000	/* default load address	*/
+
+#define	CFG_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/
+
+#define	CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xF1000000	/* Non-standard value!!	*/
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x10000000
+#ifdef	DEBUG
+#define	CFG_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
+#else
+#if 0 /* need more space for I2C tests */
+#define	CFG_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
+#else
+#define	CFG_MONITOR_LEN		(256 << 10)
+#endif
+#endif
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	124	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#undef	CFG_ENV_IS_IN_FLASH
+#undef	CFG_ENV_IS_IN_NVRAM
+#undef  CFG_ENV_IS_IN_NVRAM
+#undef	DEBUG_I2C
+#define	CFG_ENV_IS_IN_EEPROM
+
+#ifdef	CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_ADDR		0x20000000	/* use SRAM	*/
+#define CFG_ENV_SIZE		(16<<10)	/* use 16 kB	*/
+#endif	/* CFG_ENV_IS_IN_NVRAM */
+
+#ifdef	CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_OFFSET		 512	/* Leave 512 bytes free for other data	*/
+#define CFG_ENV_SIZE		1536	/* Use remaining space			*/
+#endif	/* CFG_ENV_IS_IN_EEPROM */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ * +0x0004
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * +0x0000 => 0x80600800
+ */
+#define CFG_SIUMCR	(SIUMCR_EARB   | SIUMCR_EARP0 | \
+			 SIUMCR_DBGC11 | SIUMCR_MLRC10)
+
+/*-----------------------------------------------------------------------
+ * Clock Setting - the IP860 has no 32kHz clock, so automatic detection fails
+ *-----------------------------------------------------------------------
+ */
+#define	CONFIG_8xx_GCLK_FREQ	50000000
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ * +0x0200 => 0x00C2
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ * +0x0240 => 0x0082
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* +0x0286 => was: 0x0000D000 */
+#define CFG_PLPRCR							\
+		(	PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST |	\
+			/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL |		\
+			PLPRCR_CSR   | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/	\
+		)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CFG_SCCR	(SCCR_COM00	|   SCCR_TBS	  |	\
+			 SCCR_RTDIV	|   SCCR_RTSEL	  |	\
+			 /*SCCR_CRQEN|*/  /*SCCR_PRQEN|*/	\
+			 SCCR_EBDF00	|   SCCR_DFSYNC00 |	\
+			 SCCR_DFBRG00	|   SCCR_DFNL000  |	\
+			 SCCR_DFNH000)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+/* +0x0220 => 0x00C3 */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register		19-4
+ *-----------------------------------------------------------------------
+ */
+/* +0x09C4 => TIMEP=1 */
+#define CFG_RCCR 0x0100
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ * DER - Debug Event Register
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define	CFG_DER	0x2002000F*/
+#define CFG_DER	0
+
+/*
+ * Init Memory Controller:
+ */
+
+/*
+ * MAMR settings for SDRAM	- 16-14
+ * => 0xC3804114
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA	0xC3
+
+#define CFG_MAMR	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+/*
+ * BR1 and OR1 (FLASH)
+ */
+#define FLASH_BASE		0x10000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+/* allow for max 8 MB of Flash */
+#define CFG_REMAP_OR_AM		0xFF800000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
+
+#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM	((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
+
+#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM	CFG_BR0_PRELIM
+
+/*
+ * BR2/OR2 - SDRAM
+ */
+#define SDRAM_BASE		0x00000000	/* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM	0xF8000000	/* map max. 128 MB */
+#define SDRAM_TIMING		0x00000A00	/* SDRAM-Timing */
+
+#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB SDRAM */
+
+#define CFG_OR2		(SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
+#define CFG_BR2		((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/*
+ * BR3/OR3 - SRAM (16 bit)
+ */
+#define	SRAM_BASE	0x20000000
+#define CFG_OR3		0xFFF00130		/* BI/SCY = 5/TRLX (internal) */
+#define CFG_BR3		((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+#define SRAM_SIZE	(1 + (~(CFG_OR3 & BR_BA_MSK)))
+#define CFG_OR3_PRELIM	CFG_OR3			/* Make sure to map early */
+#define CFG_BR3_PRELIM	CFG_BR3			/* in case it's used for ENV */
+
+/*
+ * BR4/OR4 - Board Control & Status (8 bit)
+ */
+#define	BCSR_BASE	0xFC000000
+#define CFG_OR4		0xFFFF0120		/* BI (internal) */
+#define CFG_BR4		((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+
+/*
+ * BR5/OR5 - IP Slot A/B (16 bit)
+ */
+#define	IP_SLOT_BASE	0x40000000
+#define CFG_OR5		0xFE00010C		/* SETA/TRLX/BI/ SCY=0 (external) */
+#define CFG_BR5		((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+
+/*
+ * BR6/OR6 - VME STD  (16 bit)
+ */
+#define	VME_STD_BASE	0xFE000000
+#define CFG_OR6		0xFF00010C		/* SETA/TRLX/BI/SCY=0  (external) */
+#define CFG_BR6		((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+
+/*
+ * BR7/OR7 - SHORT I/O + RTC + IACK  (16 bit)
+ */
+#define VME_SHORT_BASE	0xFF000000
+#define CFG_OR7		0xFF00010C		/* SETA/TRLX/BI/ SCY=0 (external) */
+#define CFG_BR7		((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+
+/*-----------------------------------------------------------------------
+ * Board Control and Status Region:
+ *-----------------------------------------------------------------------
+ */
+#ifndef __ASSEMBLY__
+typedef	struct ip860_bcsr_s {
+	unsigned char	shmem_addr;	/* +00 shared memory address register	*/
+	unsigned char	reserved0;
+	unsigned char	mbox_addr;	/* +02 mailbox address register		*/
+	unsigned char	reserved1;
+	unsigned char	vme_int_mask;	/* +04 VME Bus interrupt mask register	*/
+	unsigned char	reserved2;
+	unsigned char	vme_int_pend;	/* +06 VME interrupt pending register	*/
+	unsigned char	reserved3;
+	unsigned char	bd_int_mask;	/* +08 board interrupt mask register	*/
+	unsigned char	reserved4;
+	unsigned char	bd_int_pend;	/* +0A board interrupt pending register	*/
+	unsigned char	reserved5;
+	unsigned char	bd_ctrl;	/* +0C board control register		*/
+	unsigned char	reserved6;
+	unsigned char	bd_status;	/* +0E board status  register		*/
+	unsigned char	reserved7;
+	unsigned char	vme_irq;	/* +10 VME interrupt request register	*/
+	unsigned char	reserved8;
+	unsigned char	vme_ivec;	/* +12 VME interrupt vector register	*/
+	unsigned char	reserved9;
+	unsigned char	cli_mbox;	/* +14 clear mailbox irq		*/
+	unsigned char	reservedA;
+	unsigned char	rtc;		/* +16 RTC control register		*/
+	unsigned char	reservedB;
+	unsigned char	mbox_data;	/* +18 mailbox read/write register	*/
+	unsigned char	reservedC;
+	unsigned char	wd_trigger;	/* +1A Watchdog trigger register	*/
+	unsigned char	reservedD;
+	unsigned char	rmw_req;	/* +1C RMW request register		*/
+} ip860_bcsr_t;
+#endif	/* __ASSEMBLY__ */
+
+/*-----------------------------------------------------------------------
+ * Board Control Register: bd_ctrl (Offset 0x0C)
+ *-----------------------------------------------------------------------
+ */
+#define BD_CTRL_IPLSE	0x80	/* IP Slot Long Select Enable		*/
+#define BD_CTRL_WDOGE	0x40	/* Watchdog Enable			*/
+#define BD_CTRL_FLWE	0x20	/* Flash Write Enable			*/
+#define BD_CTRL_RWDN	0x10	/* VMEBus Requester Release When Done Enable */
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
new file mode 100644
index 00000000000..6b7079edf6a
--- /dev/null
+++ b/include/configs/IPHASE4539.h
@@ -0,0 +1,354 @@
+/*
+ * (C) Copyright 2002 Wolfgang Grandegger <wg@denx.de>
+ *
+ * This file is based on similar values for other boards found in
+ * other U-Boot config files, mainly tqm8260.h and mpc8260ads.h.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Config header file for a Interphase 4539 PMC, 64 MB SDRAM, 4MB Flash.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG				/* General debug */
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
+#define CONFIG_IPHASE4539	1	/* ...on a Interphase 4539 PMC */
+
+/*-----------------------------------------------------------------------
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define	CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#undef	CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef	CONFIG_CONS_NONE		/* define if console on something else */
+#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
+
+/*-----------------------------------------------------------------------
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC   */
+#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+#define CONFIG_ETHER_INDEX	3	/* which channel for ether  */
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
+
+/*-----------------------------------------------------------------------
+ * - Rx-CLK is CLK14
+ * - Tx-CLK is CLK16
+ * - Select bus for bd/buffers (see 28-13)
+ * - Half duplex
+ */
+# define CFG_CMXFCR_MASK	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+# define CFG_CMXFCR_VALUE	(CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16)
+# define CFG_CPMFCR_RAMTYPE	0
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#endif	/* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
+
+/* other options */
+
+#define CONFIG_8260_CLKIN	66666666	/* in Hz */
+#define CONFIG_BAUDRATE		19200
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+/*
+ * select i2c support configuration
+ *
+ * Supported configurations are {none, software, hardware} drivers.
+ * If the software driver is chosen, there are some additional
+ * configuration items that the driver uses to drive the port pins.
+ */
+#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#ifdef CONFIG_SOFT_I2C
+#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
+#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
+#define I2C_READ	((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00010000; \
+			else    iop->pdat &= ~0x00010000
+#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
+			else    iop->pdat &= ~0x00020000
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+#endif /* CONFIG_SOFT_I2C */
+
+#define CONFIG_COMMANDS		CONFIG_CMD_DFL
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* autoboot command */
+#define CONFIG_BOOTARGS		"root=/dev/ram rw"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
+#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
+#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
+#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
+#endif
+
+#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)  /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x00F00000	/* 1 ... 15 MB in DRAM	*/
+
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passed to Linux in MHz */
+					/* for versions < 2.4.5-pre5	 */
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS	0x04400000
+
+#define CONFIG_MISC_INIT_R	1	/* We need misc_init_r()	*/
+
+/*-----------------------------------------------------------------------
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration (Setup by the
+ * startup code). Please note that CFG_SDRAM_BASE _must_ start at 0.
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFF800000
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 << 10)     /* Reserve 256 kB for Monitor  */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks	*/
+#define CFG_MAX_FLASH_SECT	64	/* max num of sects on one chip */
+#define CFG_MAX_FLASH_SIZE	(CFG_MAX_FLASH_SECT * 0x10000)	/* 4 MB */
+
+#define CFG_FLASH_ERASE_TOUT	2400000	/* Flash Erase Timeout (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
+
+/* Environment in FLASH, there is little space left in Serial EEPROM */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_SECT_SIZE	0x10000 /* We use one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x10000) /* 2. sector */
+
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#define CFG_HRCW_MASTER ( ( HRCW_BPS01 | HRCW_EBM )		|\
+			  ( HRCW_L2CPC10 | HRCW_ISB110 )	|\
+			  ( HRCW_MMR11 | HRCW_APPC10 )		|\
+			  ( HRCW_CS10PC01 | HRCW_MODCK_H0101 )	 \
+			) /* 0x14863245 */
+
+/* no slaves */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFF000000 /* We keep original value */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	  /* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02	  /* Software reboot			*/
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32     /* For MPC8260 CPU		*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT	5      /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers		2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ 			 HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL	(HID0_IFEM|HID0_ABE)
+#define CFG_HID2	0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register					 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR		RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration					 4-25
+ *-----------------------------------------------------------------------
+ */
+#define CFG_BCR		0xA01C0000
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				 4-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR	0X4205C000
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined (CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+			 SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control			 4-40
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ *-----------------------------------------------------------------------
+ */
+#define CFG_TMCNTSC	(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control					 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR	0
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration				13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR	0
+
+/*-----------------------------------------------------------------------
+ * Init Memory Controller:
+ *
+ * Bank Bus	Machine PortSz	Device
+ * ---- ---	------- ------	------
+ *  0	60x	GPCM	64 bit	FLASH
+ *  1	60x	SDRAM	64 bit	SDRAM
+ */
+
+#define CFG_BR0_PRELIM	((CFG_FLASH_BASE & BRx_BA_MSK) | 0x0801)
+#define CFG_OR0_PRELIM	0xFF800882
+#define CFG_BR1_PRELIM	((CFG_SDRAM_BASE & BRx_BA_MSK) | 0x0041)
+#define CFG_OR1_PRELIM	0xF8002CD0
+
+#define CFG_PSDMR	0x404A241A
+#define CFG_MPTPR	0x00007400
+#define CFG_PSRT	0x00000007
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/MBX.h b/include/configs/MBX.h
new file mode 100644
index 00000000000..e62d36cc059
--- /dev/null
+++ b/include/configs/MBX.h
@@ -0,0 +1,307 @@
+/*
+ * (C) Copyright 2000
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the MBX8xx board.
+ *
+ * -----------------------------------------------------------------
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * Changed 2002-10-01
+ * Added PCMCIA defines mostly taken from other U-Boot boards that
+ * have PCMCIA already working.  If you find any bugs, incorrect assumptions
+ * feel free to fix them yourself and submit a patch.
+ * Rod Boyce <rod_boyce@stratexnet.com.
+ */
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
+#define CONFIG_MBX		1	/* ...on an MBX module		*/
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		9600
+/* Define this to use the PCI bus */
+#undef CONFIG_USE_PCI
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_8xx_GCLK_FREQ    (50000000UL)
+#if 1
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+#define CONFIG_BOOTCOMMAND	"bootm 20000" /* autoboot command	*/
+
+#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
+				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
+				"nfsaddrs=10.0.0.99:10.0.0.2"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE   /* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_COMMANDS		( CFG_CMD_NET | CONFIG_CMD_DFL | CFG_CMD_SDRAM | \
+                              CFG_CMD_PCMCIA | CFG_CMD_IDE )
+
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#undef	CFG_HUSH_PARSER			/* Hush parse for U-Boot	*/
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#endif
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Physical memory map as defined by the MBX PGM
+ */
+#define CFG_IMMR		0xFA200000 /* Internal Memory Mapped Register*/
+#define CFG_NVRAM_BASE		0xFA000000 /* NVRAM			     */
+#define CFG_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
+#define CFG_CSR_BASE		0xFA100000 /* Control/Status Registers	     */
+#define CFG_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces	     */
+#define CFG_PCIMEM_OR		0xA0000108
+#define CFG_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers	     */
+#define CFG_PCIBRIDGE_OR	0xFFFF0108
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x2f00	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
+#define CFG_INIT_VPD_OFFSET	(CFG_GBL_DATA_OFFSET - CFG_INIT_VPD_SIZE)
+#define CFG_INIT_SP_OFFSET	(CFG_INIT_VPD_OFFSET-8)
+
+/*-----------------------------------------------------------------------
+ * Offset in DPMEM where we keep the VPD data
+ */
+#define CFG_DPRAMVPD		(CFG_INIT_VPD_OFFSET - 0x2000)
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xfe000000
+#ifdef	DEBUG
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#else
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#endif
+#undef	CFG_MONITOR_BASE	/* 0x200000	   to run U-Boot from RAM */
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+/*-----------------------------------------------------------------------
+ * NVRAM Configuration
+ *
+ * Note: the MBX is special because there is already a firmware on this
+ * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
+ * access the NVRAM at the offset 0x1000.
+ */
+#define CFG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
+#define CFG_ENV_ADDR		(CFG_NVRAM_BASE + 0x1000)
+#define CFG_ENV_SIZE		0x1000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+/* #define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */
+#define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC )
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
+#define CFG_SCCR	SCCR_TBS
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+#define CFG_PCMCIA_INTERRUPT	SIU_LEVEL6
+
+#define CONFIG_PCMCIA_SLOT_A	1
+
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
+#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ * Debug Entry Mode
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h
new file mode 100644
index 00000000000..78caafd847d
--- /dev/null
+++ b/include/configs/MHPC.h
@@ -0,0 +1,371 @@
+/*
+ * (C) Copyright 2001
+ * Frank Gottschling, ELTEC Elektronik AG, fgottschling@eltec.de
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Configuation settings for the miniHiPerCam.
+ *
+ * -----------------------------------------------------------------
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
+#define CONFIG_MHPC 		1	/* on a miniHiPerCam	        */
+#define CONFIG_BOARD_PRE_INIT   1       /* do special hardware init.    */
+#define CONFIG_MISC_INIT_R      1
+
+#define CONFIG_8xx_GCLK_FREQ	MPC8XX_SPEED
+#undef	CONFIG_8xx_CONS_SMC1
+#define	CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#define CONFIG_ENV_OVERWRITE    1
+#define CONFIG_ETHADDR          00:00:5b:ee:de:ad
+
+#undef  CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND	\
+	"bootp;"								\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+
+#undef  CONFIG_UCODE_PATCH
+
+/* enable I2C and select the hardware/software driver */
+#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED                   50000
+#define CFG_I2C_SLAVE                   0xFE
+#define CFG_I2C_EEPROM_ADDR             0x50    /* EEPROM X24C04		*/
+#define CFG_I2C_EEPROM_ADDR_LEN         1       /* bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW    0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS      3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS  10
+
+#define LCD_VIDEO_ADDR          (SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
+#define LCD_VIDEO_SIZE          SDRAM_RES_SIZE  /* 2MB */
+#define LCD_VIDEO_COLS          640
+#define LCD_VIDEO_ROWS          480
+#define LCD_VIDEO_FG            255
+#define LCD_VIDEO_BG            0
+
+#undef  CONFIG_VIDEO                            /* test only ! s.a devices.c and 8xx */
+#define CONFIG_CFB_CONSOLE                      /* framebuffer console with std input */
+#define CONFIG_VIDEO_LOGO
+
+#define VIDEO_KBD_INIT_FCT      0               /* no KBD dev on MHPC - use serial */
+#define VIDEO_TSTC_FCT          serial_tstc
+#define VIDEO_GETC_FCT          serial_getc
+
+#define CONFIG_BR0_WORKAROUND   1
+
+#define CONFIG_COMMANDS	     ( CONFIG_CMD_DFL  | \
+                               CFG_CMD_DATE    | \
+                               CFG_CMD_EEPROM  | \
+                               CFG_CMD_ELF     | \
+                               CFG_CMD_I2C     | \
+                               CFG_CMD_JFFS2   | \
+                               CFG_CMD_REGINFO )
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x300000	/* default load address	*/
+
+#define	CFG_HZ                  1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Physical memory map
+ */
+#define CFG_IMMR		0xFFF00000 /* Internal Memory Mapped Register*/
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE       64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xfe000000
+
+#define	CFG_MONITOR_LEN		0x40000 	/* Reserve 256 kB for Monitor	*/
+#undef  CFG_MONITOR_BASE	            /* to run U-Boot from RAM */
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* one flash only */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map- for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	64	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		CFG_MONITOR_LEN	/* Offset of Environment */
+#define	CFG_ENV_SIZE		0x20000	/* Total Size of Environment 	*/
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+                         SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR	(SIUMCR_SEME)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		12-18
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define MPC8XX_SPEED	50000000L
+#define MPC8XX_XIN   	5000000L      /* ref clk */
+#define MPC8XX_FACT	(MPC8XX_SPEED/MPC8XX_XIN)
+#define CFG_PLPRCR	(((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+                        PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+
+#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)     /* SCCR_EBDF11 */
+#define CFG_SCCR	(SCCR_TBS | SCCR_DFLCD001)
+
+
+/*-----------------------------------------------------------------------
+ * MAMR settings for SDRAM	- 16-14
+ * => 0xC080200F
+ *-----------------------------------------------------------------------
+ * periodic timer for refresh
+ */
+#define CFG_MAMR_PTA	0xC0
+#define CFG_MAMR	((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | MAMR_G0CLA_A11 | MAMR_TLFA_MSK)
+
+/*
+ * BR0 and OR0 (FLASH) used to re-map FLASH
+ */
+
+/* allow for max 8 MB of Flash */
+#define FLASH_BASE		0xFE000000	/* FLASH bank #0*/
+#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0*/
+#define CFG_REMAP_OR_AM		0xFF800000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
+
+#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_BI | OR_SCY_8_CLK) /* (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)*/
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM	((FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V )
+
+/*
+ * BR1 and OR1 (SDRAM)
+ */
+#define SDRAM_BASE1_PRELIM	0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_MAX_SIZE		0x01000000	/* max 16 MB    	*/
+#define SDRAM_RES_SIZE          0x00200000      /* 2 MB for framebuffer */
+
+/* SDRAM timing: drive GPL5 high on first cycle */
+#define CFG_OR_TIMING_SDRAM	(OR_G5LS)
+
+#define CFG_OR1_PRELIM	((~(SDRAM_MAX_SIZE)+1)| CFG_OR_TIMING_SDRAM )
+#define CFG_BR1_PRELIM	((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/*
+ * BR2/OR2 - DIMM
+ */
+#define CFG_OR2		(OR_ACS_DIV4)
+#define CFG_BR2		(BR_MS_UPMA)
+
+/*
+ * BR3/OR3 - DIMM
+ */
+#define CFG_OR3		(OR_ACS_DIV4)
+#define CFG_BR3		(BR_MS_UPMA)
+
+/*
+ * BR4/OR4
+ */
+#define CFG_OR4		0
+#define CFG_BR4		0
+
+/*
+ * BR5/OR5
+ */
+#define CFG_OR5		0
+#define CFG_BR5		0
+
+/*
+ * BR6/OR6
+ */
+#define CFG_OR6		0
+#define CFG_BR6		0
+
+/*
+ * BR7/OR7
+ */
+#define CFG_OR7		0
+#define CFG_BR7		0
+
+
+/*-----------------------------------------------------------------------
+ * Debug Entry Mode
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER	0
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
new file mode 100644
index 00000000000..f6d186f6ee6
--- /dev/null
+++ b/include/configs/MPC8260ADS.h
@@ -0,0 +1,267 @@
+/*
+ * (C) Copyright 2001
+ * Stuart Hughes <stuarth@lineo.com>
+ * This file is based on similar values for other boards found in other
+ * U-Boot config files, and some that I found in the mpc8260ads manual.
+ *
+ * Note: my board is a PILOT rev.
+ * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
+#define CONFIG_MPC8260ADS	1	/* ...on motorola ads board */
+
+#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init	*/
+
+/* allow serial and ethaddr to be overwritten */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#undef	CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#define CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef	CONFIG_CONS_NONE		/* define if console on something else */
+#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC   */
+#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+#define CONFIG_ETHER_INDEX	2	/* which channel for ether  */
+
+#if (CONFIG_ETHER_INDEX == 2)
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - Select bus for bd/buffers (see 28-13)
+ * - Half duplex
+ */
+# define CFG_CMXFCR_MASK	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE	0
+# define CFG_FCC_PSMR		0
+
+#endif	/* CONFIG_ETHER_INDEX */
+
+/* other options */
+#define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+
+#define CONFIG_8260_CLKIN	66666666	/* in Hz */
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_COMMANDS		(CFG_CMD_ALL & ~( \
+				 CFG_CMD_BEDBUG | \
+				 CFG_CMD_BSP	| \
+				 CFG_CMD_DATE	| \
+				 CFG_CMD_DOC	| \
+				 CFG_CMD_DTT	| \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_ELF    | \
+				 CFG_CMD_FDC	| \
+				 CFG_CMD_HWFLOW	| \
+				 CFG_CMD_IDE	| \
+				 CFG_CMD_JFFS2	| \
+				 CFG_CMD_KGDB	| \
+				 CFG_CMD_MII	| \
+				 CFG_CMD_PCI	| \
+				 CFG_CMD_PCMCIA | \
+				 CFG_CMD_SCSI	| \
+				 CFG_CMD_VFD	| \
+				 CFG_CMD_USB	) )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* autoboot command */
+#define CONFIG_BOOTARGS		"root=/dev/ram rw"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
+#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
+#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
+#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
+#endif
+
+#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory	    */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt   */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size  */
+#else
+#define CFG_CBSIZE	256			/* Console I/O Buffer Size  */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS	16			/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on */
+#define CFG_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
+
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+					/* for versions < 2.4.5-pre5	*/
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
+
+#define CFG_FLASH_BASE		0xff800000
+#define FLASH_BASE		0xff800000
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks	*/
+#define CFG_MAX_FLASH_SECT	32	/* max num of sects on one chip */
+#define CFG_FLASH_SIZE		8
+#define CFG_FLASH_ERASE_TOUT	8000	/* Timeout for Flash Erase (in ms)    */
+#define CFG_FLASH_WRITE_TOUT	5	/* Timeout for Flash Write (in ms)    */
+
+/* this is stuff came out of the Motorola docs */
+#define CFG_DEFAULT_IMMR	0x0F010000
+
+#define CFG_IMMR		0x04700000
+#define CFG_BCSR		0x04500000
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_LSDRAM_BASE		0x04000000
+
+#define RS232EN_1		0x02000002
+#define RS232EN_2		0x01000001
+#define FETHIEN			0x08000008
+#define FETH_RST		0x04000004
+
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+
+/* 0x0EA28205 */
+#define CFG_HRCW_MASTER (   ( HRCW_BPS11 | HRCW_CIP )			    |\
+			    ( HRCW_L2CPC10 | HRCW_DPPC10 | HRCW_ISB010 )    |\
+			    ( HRCW_BMS | HRCW_APPC10 )			    |\
+			    ( HRCW_MODCK_H0101 )			     \
+			)
+
+/* no slaves */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH  */
+#define BOOTFLAG_WARM	0x02	/* Software reboot	     */
+
+#define CFG_MONITOR_BASE    TEXT_BASE
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#   define CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+#ifndef CFG_RAMBOOT
+#  define CFG_ENV_IS_IN_FLASH	1
+#    define CFG_ENV_ADDR	(CFG_MONITOR_BASE + 0x40000)
+#    define CFG_ENV_SECT_SIZE	0x40000
+#else
+#  define CFG_ENV_IS_IN_NVRAM	1
+#  define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#  define CFG_ENV_SIZE		0x200
+#endif /* CFG_RAMBOOT */
+
+
+#define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+
+#define CFG_HID0_INIT		0
+#define CFG_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE )
+
+#define CFG_HID2		0
+
+#define CFG_SYPCR		0xFFFFFFC3
+#define CFG_BCR			0x100C0000
+#define CFG_SIUMCR		0x0A200000
+#define CFG_SCCR		0x00000000
+#define CFG_BR0_PRELIM		0xFF801801
+#define CFG_OR0_PRELIM		0xFF800836
+#define CFG_BR1_PRELIM		0x04501801
+#define CFG_OR1_PRELIM		0xFFFF8010
+
+#define CFG_RMR			0
+#define CFG_TMCNTSC		(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CFG_PISCR		(PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CFG_RCCR		0
+#define CFG_PSDMR		0x016EB452
+#define CFG_MPTPR		0x00001900
+#define CFG_PSRT		0x00000021
+
+#define CFG_RESET_ADDRESS	0x04400000
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/PCIPPC2.h b/include/configs/PCIPPC2.h
new file mode 100644
index 00000000000..b48d0d701d4
--- /dev/null
+++ b/include/configs/PCIPPC2.h
@@ -0,0 +1,266 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ *
+ * Configuration settings for the PCIPPC-2 board.
+ *
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_PCIPPC2		1	/* this is a PCIPPC2 board	*/
+
+#define CONFIG_BOARD_PRE_INIT	1
+#define CONFIG_MISC_INIT_R	1
+
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_BAUDRATE		9600
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passed to Linux in MHz */
+
+#define CONFIG_PREBOOT		""
+#define CONFIG_BOOTDELAY	5
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
+			         CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_COMMANDS	        (CONFIG_CMD_DFL	| \
+				 CFG_CMD_ASKENV	| \
+				 CFG_CMD_BSP	| \
+				 CFG_CMD_DATE	| \
+				 CFG_CMD_DHCP	| \
+				 CFG_CMD_DOC	| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_PCI	)
+
+#define CONFIG_PCI		1
+#define CONFIG_PCI_PNP		1	/* PCI plug-and-play */
+
+/* This must be included AFTER the definition of CONFIG_COMMANDS (if any)
+ */
+#include <cmd_confdefs.h>
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+
+/* Print Buffer Size
+ */
+#define CFG_PBSIZE	(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+
+#define	CFG_MAXARGS	64		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_LOAD_ADDR	0x00100000	/* Default load address		*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE	    0x00000000
+#define CFG_FLASH_BASE	    0xFFF00000
+#define CFG_FLASH_MAX_SIZE  0x00100000
+/* Maximum amount of RAM.
+ */
+#define CFG_MAX_RAM_SIZE    0x20000000  /* 512Mb			*/
+
+#define CFG_RESET_ADDRESS   0xFFF00100
+
+#define CFG_MONITOR_BASE    TEXT_BASE
+
+#define CFG_MONITOR_LEN	    (256 << 10) /* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN	    (128 << 10) /* Reserve 128 kB for malloc()	*/
+
+#if CFG_MONITOR_BASE >= CFG_SDRAM_BASE && \
+    CFG_MONITOR_BASE < CFG_SDRAM_BASE + CFG_MAX_RAM_SIZE
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_MEMTEST_START   0x00004000	/* memtest works on		*/
+#define CFG_MEMTEST_END	    0x02000000	/* 0 ... 32 MB in DRAM		*/
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+/* Size in bytes reserved for initial data
+ */
+#define CFG_GBL_DATA_SIZE    128
+
+#define CFG_INIT_RAM_ADDR     0x40000000
+#define CFG_INIT_RAM_END      0x8000
+#define CFG_GBL_DATA_OFFSET  (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET    CFG_GBL_DATA_OFFSET
+
+#define CFG_INIT_RAM_LOCK
+
+/*
+ * Temporary buffer for serial data until the real serial driver
+ * is initialised (memtest will destroy this buffer)
+ */
+#define CFG_SCONSOLE_ADDR     CFG_INIT_RAM_ADDR
+#define CFG_SCONSOLE_SIZE     0x0002000
+
+/* SDRAM 0 - 256MB
+ */
+#define CFG_DBAT0L	      (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U	      (CFG_SDRAM_BASE | \
+			       BATU_BL_256M | BATU_VS | BATU_VP)
+/* SDRAM 1 - 256MB
+ */
+#define CFG_DBAT1L	      ((CFG_SDRAM_BASE + 0x10000000) | \
+			       BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT1U	      ((CFG_SDRAM_BASE + 0x10000000) | \
+			       BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* Init RAM in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT2L	      (CFG_INIT_RAM_ADDR | \
+			       BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT2U	      (CFG_INIT_RAM_ADDR | \
+			       BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* I/O and PCI memory at 0xf0000000
+ */
+#define CFG_DBAT3L	      (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_DBAT3U	      (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT0L	      CFG_DBAT0L
+#define CFG_IBAT0U	      CFG_DBAT0U
+#define CFG_IBAT1L	      CFG_DBAT1L
+#define CFG_IBAT1U	      CFG_DBAT1U
+#define CFG_IBAT2L	      CFG_DBAT2L
+#define CFG_IBAT2U	      CFG_DBAT2U
+#define CFG_IBAT3L	      CFG_DBAT3L
+#define CFG_IBAT3U	      CFG_DBAT3U
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ * For the detail description refer to the PCIPPC2 user's manual.
+ */
+#define CFG_HZ		      1000
+#define CFG_BUS_HZ            100000000 /* bus speed - 100 mhz          */
+#define CFG_CPU_CLK	      300000000
+#define CFG_BUS_CLK	      100000000
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	      (8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* Max number of flash banks		*/
+#define CFG_MAX_FLASH_SECT	16	/* Max number of sectors in one bank	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+/*
+ * Note: environment is not EMBEDDED in the U-Boot code.
+ * It's stored in flash separately.
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x70000)
+#define CFG_ENV_SIZE		0x1000	/* Size of the Environment		*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* Size of the Environment Sector	*/
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * L2 cache
+ */
+#undef CFG_L2
+#define L2_INIT   (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+                   L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM		0x02	/* Software reboot			*/
+
+/*-----------------------------------------------------------------------
+ * Disk-On-Chip configuration
+ */
+
+#define CFG_MAX_DOC_DEVICE	1	/* Max number of DOC devices		*/
+
+#define CFG_DOC_SUPPORT_2000
+#undef CFG_DOC_SUPPORT_MILLENNIUM
+
+/*-----------------------------------------------------------------------
+  RTC m48t59
+*/
+#define CONFIG_RTC_MK48T59
+
+#define CONFIG_WATCHDOG
+
+#define CONFIG_NET_MULTI			/* Multi ethernet cards support */
+
+#define CONFIG_EEPRO100
+#define CONFIG_TULIP
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/PCIPPC6.h b/include/configs/PCIPPC6.h
new file mode 100644
index 00000000000..bf858ec4174
--- /dev/null
+++ b/include/configs/PCIPPC6.h
@@ -0,0 +1,282 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ *
+ * Configuration settings for the PCIPPC-6 board.
+ *
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_PCIPPC2		1	/* this is a PCIPPC2 board	*/
+
+#define CONFIG_BOARD_PRE_INIT	1
+#define CONFIG_MISC_INIT_R	1
+
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_BAUDRATE		9600
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passed to Linux in MHz */
+
+#define CONFIG_PREBOOT		""
+#define CONFIG_BOOTDELAY	5
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
+				 CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | \
+				 CFG_CMD_ASKENV	| \
+				 CFG_CMD_BSP	| \
+				 CFG_CMD_DATE	| \
+				 CFG_CMD_DHCP	| \
+				 CFG_CMD_DOC	| \
+				 CFG_CMD_ELF	| \
+				 CFG_CMD_PCI	| \
+				 CFG_CMD_SCSI	)
+
+
+#define CONFIG_PCI		1
+#define CONFIG_PCI_PNP		1	/* PCI plug-and-play */
+
+/* This must be included AFTER the definition of CONFIG_COMMANDS (if any)
+ */
+#include <cmd_confdefs.h>
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#define CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#endif
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+
+/* Print Buffer Size
+ */
+#define CFG_PBSIZE	(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+
+#define CFG_MAXARGS	64		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_LOAD_ADDR	0x00100000	/* Default load address		*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE	    0x00000000
+#define CFG_FLASH_BASE	    0xFFF00000
+#define CFG_FLASH_MAX_SIZE  0x00100000
+/* Maximum amount of RAM.
+ */
+#define CFG_MAX_RAM_SIZE    0x20000000	/* 512Mb			*/
+
+#define CFG_RESET_ADDRESS   0xFFF00100
+
+#define CFG_MONITOR_BASE    TEXT_BASE
+
+#define CFG_MONITOR_LEN	    (256 << 10) /* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN	    (128 << 10) /* Reserve 128 kB for malloc()	*/
+
+#if CFG_MONITOR_BASE >= CFG_SDRAM_BASE && \
+    CFG_MONITOR_BASE < CFG_SDRAM_BASE + CFG_MAX_RAM_SIZE
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_MEMTEST_START   0x00004000	/* memtest works on		*/
+#define CFG_MEMTEST_END	    0x02000000	/* 0 ... 32 MB in DRAM		*/
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+/* Size in bytes reserved for initial data
+ */
+#define CFG_GBL_DATA_SIZE    128
+
+#define CFG_INIT_RAM_ADDR     0x40000000
+#define CFG_INIT_RAM_END      0x8000
+#define CFG_GBL_DATA_OFFSET  (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET    CFG_GBL_DATA_OFFSET
+
+#define CFG_INIT_RAM_LOCK
+
+/*
+ * Temporary buffer for serial data until the real serial driver
+ * is initialised (memtest will destroy this buffer)
+ */
+#define CFG_SCONSOLE_ADDR     CFG_INIT_RAM_ADDR
+#define CFG_SCONSOLE_SIZE     0x0002000
+
+/* SDRAM 0 - 256MB
+ */
+#define CFG_DBAT0L	      (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U	      (CFG_SDRAM_BASE | \
+			       BATU_BL_256M | BATU_VS | BATU_VP)
+/* SDRAM 1 - 256MB
+ */
+#define CFG_DBAT1L	      ((CFG_SDRAM_BASE + 0x10000000) | \
+			       BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT1U	      ((CFG_SDRAM_BASE + 0x10000000) | \
+			       BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* Init RAM in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT2L	      (CFG_INIT_RAM_ADDR | \
+			       BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_DBAT2U	      (CFG_INIT_RAM_ADDR | \
+			       BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* I/O and PCI memory at 0xf0000000
+ */
+#define CFG_DBAT3L	      (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_DBAT3U	      (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT0L	      CFG_DBAT0L
+#define CFG_IBAT0U	      CFG_DBAT0U
+#define CFG_IBAT1L	      CFG_DBAT1L
+#define CFG_IBAT1U	      CFG_DBAT1U
+#define CFG_IBAT2L	      CFG_DBAT2L
+#define CFG_IBAT2U	      CFG_DBAT2U
+#define CFG_IBAT3L	      CFG_DBAT3L
+#define CFG_IBAT3U	      CFG_DBAT3U
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ * For the detail description refer to the PCIPPC2 user's manual.
+ */
+#define CFG_HZ		      1000
+#define CFG_BUS_HZ	      100000000 /* bus speed - 100 mhz		*/
+#define CFG_CPU_CLK	      300000000
+#define CFG_BUS_CLK	      100000000
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	      (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* Max number of flash banks		*/
+#define CFG_MAX_FLASH_SECT	16	/* Max number of sectors in one bank	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+/*
+ * Note: environment is not EMBEDDED in the U-Boot code.
+ * It's stored in flash separately.
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x70000)
+#define CFG_ENV_SIZE		0x1000	/* Size of the Environment		*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* Size of the Environment Sector	*/
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * L2 cache
+ */
+#undef CFG_L2
+#define L2_INIT	  (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
+		   L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM		0x02	/* Software reboot			*/
+
+/*-----------------------------------------------------------------------
+ * Disk-On-Chip configuration
+ */
+
+#define CFG_MAX_DOC_DEVICE	1	/* Max number of DOC devices		*/
+
+#define CFG_DOC_SUPPORT_2000
+#undef CFG_DOC_SUPPORT_MILLENNIUM
+
+/*-----------------------------------------------------------------------
+  RTC m48t59
+*/
+#define CONFIG_RTC_MK48T59
+
+#define CONFIG_WATCHDOG
+
+#define CONFIG_NET_MULTI		/* Multi ethernet cards support */
+
+#define CONFIG_EEPRO100
+#define CONFIG_TULIP
+
+
+#define CONFIG_SCSI_SYM53C8XX
+#define CONFIG_SCSI_DEV_ID	0x000B	/* 53c896 */
+#define CFG_SCSI_MAX_LUN	8	/* number of supported LUNs */
+#define CFG_SCSI_MAX_SCSI_ID	15	/* maximum SCSI ID (0..6) */
+#define CFG_SCSI_MAX_DEVICE	CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */
+#define CFG_SCSI_SPIN_UP_TIME	2
+#define CFG_SCSI_SCAN_BUS_REVERSE 0
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION
+
+
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/RRvision.h b/include/configs/RRvision.h
new file mode 100644
index 00000000000..ad36c95603d
--- /dev/null
+++ b/include/configs/RRvision.h
@@ -0,0 +1,467 @@
+/*
+ * (C) Copyright 2000, 2001, 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
+#define CONFIG_RRVISION		1	/* ...on a RRvision board	*/
+
+#define CONFIG_8xx_GCLK_FREQ 64000000
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds	*/
+#endif
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT	"setenv stdout serial"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_ETHADDR                00:50:C2:00:E0:70
+#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
+#define CONFIG_IPADDR                 10.0.0.5
+#define CONFIG_SERVERIP               10.0.0.2
+#define CONFIG_NETMASK                255.0.0.0
+#define CONFIG_ROOTPATH               /opt/eldk/ppc_8xx
+#define CONFIG_BOOTCOMMAND            "run flash_self"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$(serverip):$(rootpath)\0"			\
+	"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip)"	\
+		":$(gatewayip):$(netmask):$(hostname):$(netdev):off\0"	\
+	"addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
+	"load=tftp 100000 /tftpboot/u-boot.bin\0"			\
+	"update=protect off 1:0-8;era 1:0-8;"				\
+		"cp.b 100000 40000000 $(filesize);"			\
+		"setenv filesize;saveenv\0"				\
+	"kernel_addr=40040000\0"					\
+	"ramdisk_addr=40100000\0"					\
+	"kernel_img=/tftpboot/pImage\0"					\
+	"kernel_load=tftp 200000 $(kernel_img)\0"			\
+	"net_nfs=run kernel_load nfsargs addip addtty;bootm\0"		\
+	"flash_nfs=run nfsargs addip addtty;bootm $(kernel_addr)\0"	\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"
+
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#undef	CONFIG_STATUS_LED		/* disturbs display		*/
+
+#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+
+
+#if 1
+#define CONFIG_VIDEO		1	/* To enable the video initialization */
+
+/* Video related */
+#define CONFIG_VIDEO_LOGO			1	/* Show the logo */
+#define CONFIG_VIDEO_ENCODER_AD7176		1	/* Enable this encoder */
+#define CONFIG_VIDEO_ENCODER_AD7176_ADDR	0x2A	/* ALSB to ground */
+#endif
+
+/* enable I2C and select the hardware/software driver */
+#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define	CONFIG_SOFT_I2C         	/* I2C bit-banged		*/
+
+# define CFG_I2C_SPEED		50000	/* 50 kHz is supposed to work	*/
+# define CFG_I2C_SLAVE		0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(1)	/* 1/4 I2C clock duration */
+#endif	/* CONFIG_SOFT_I2C */
+
+
+
+#define CONFIG_COMMANDS	    ( ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_DATE	) & \
+			     ~( CFG_CMD_PCMCIA  | \
+			        CFG_CMD_IDE	) )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x40000000
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
+
+/* timeout values are in ticks = ms */
+#define CFG_FLASH_ERASE_TOUT	(120*CFG_HZ)	/* Timeout for Flash Erase	*/
+#define CFG_FLASH_WRITE_TOUT	(1 * CFG_HZ)	/* Timeout for Flash Write	*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define	CFG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef	CONFIG_CAN_DRIVER
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else	/* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ */
+
+/* for 64 MHz, we use a 16 MHz clock * 4 */
+#define CFG_PLPRCR ( (4-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CFG_SCCR	(/* SCCR_TBS  | */ SCCR_RTSEL | SCCR_RTDIV    | \
+			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
+#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers	*/
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define	CFG_DER	0x2002000F*/
+#define CFG_DER	0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
+
+/*
+ * FLASH timing:
+ */
+/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
+
+#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
+#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef	CONFIG_CAN_DRIVER
+#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
+#define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
+#define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
+					BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif	/* CONFIG_CAN_DRIVER */
+
+/*
+ * Memory Periodic Timer Prescaler
+ *
+ * The Divider for PTA (refresh timer) configuration is based on an
+ * example SDRAM configuration (64 MBit, one bank). The adjustment to
+ * the number of chip selects (NCS) and the actually needed refresh
+ * rate is done by setting MPTPR.
+ *
+ * PTA is calculated from
+ *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ *
+ *	gclk	  CPU clock (not bus clock!)
+ *	Trefresh  Refresh cycle * 4 (four word bursts used)
+ *
+ * 4096  Rows from SDRAM example configuration
+ * 1000  factor s -> ms
+ *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
+ *    4  Number of refresh cycles per period
+ *   64  Refresh cycle in ms per number of rows
+ * --------------------------------------------
+ * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ *
+ * 50 MHz => 50.000.000 / Divider =  98
+ * 66 Mhz => 66.000.000 / Divider = 129
+ * 80 Mhz => 80.000.000 / Divider = 156
+ */
+#define CFG_MAMR_PTA		129
+
+/*
+ * For 16 MBit, refresh rates could be 31.3 us
+ * (= 64 ms / 2K = 125 / quad bursts).
+ * For a simpler initialization, 15.6 us is used instead.
+ *
+ * #define CFG_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
+ * #define CFG_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
+ */
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
new file mode 100644
index 00000000000..1b867e056d3
--- /dev/null
+++ b/include/configs/W7OLMC.h
@@ -0,0 +1,326 @@
+/*
+ * (C) Copyright 2001
+ * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP		1		/* This is a PPC405GP CPU	*/
+#define CONFIG_4xx		1		/* ...member of PPC405 family	*/
+#define CONFIG_W7O		1		/* ...on a Wave 7 Optics board	*/
+#define CONFIG_W7OLMC		1		/* ...specifically an LMC	*/
+
+#define CONFIG_BOARD_PRE_INIT	1		/* Call board_pre_init	*/
+
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external frequency to pll	*/
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
+
+#if 1
+#define CONFIG_BOOTCOMMAND	"bootvx"	/* VxWorks boot command		*/
+#else
+#define CONFIG_BOOTCOMMAND	"bootp"		/* autoboot command		*/
+#endif
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_LOADADDR		F0080000
+
+#define CONFIG_ETHADDR		00:06:0D:00:00:00 /* Default, overridden at boot	*/
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_IPADDR		192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_SERVERIP		192.168.1.2
+
+#define CONFIG_LOADS_ECHO	1		/* echo on for serial download	*/
+#undef CFG_LOADS_BAUD_CHANGE			/* disallow baudrate change	*/
+
+#define CONFIG_MII		1		/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0		/* PHY address			*/
+
+#define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
+
+#define CONFIG_COMMANDS		\
+	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \
+	 CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \
+	 CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG				/* watchdog disabled		*/
+#define CONFIG_HW_WATCHDOG			/* HW Watchdog, board specific	*/
+
+#define	CONFIG_SPD_EEPROM			/* SPD EEPROM for SDRAM param.	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_PROMPT		"Wave7Optics> " /* Monitor Command Prompt	*/
+#undef  CFG_HUSH_PARSER				/* No hush parse for U-Boot       */
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2     "> "
+#endif
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size	*/
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
+
+#undef  CFG_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CFG_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD		384000
+
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE	{9600}
+
+#define CFG_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
+#define CFG_EXTBDINFO		1		/* use extended board_info (bd_t) */
+
+#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER	0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE		1		/* configure as pci host	*/
+#define PCI_HOST_AUTO		2		/* detected via arbiter enable	*/
+
+
+#define CONFIG_PCI				/* include pci support		*/
+#define CONFIG_PCI_HOST		PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP				/* pci plug-and-play		*/
+/* resource configuration	*/
+#define CFG_PCI_SUBSYS_VENDORID 0x1014		/* PCI Vendor ID: IBM		*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0156		/* PCI Device ID: 405GP		*/
+#define CFG_PCI_PTM1LA		0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS		0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CFG_PCI_PTM1PCI 	0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA		0x00000000	/* disabled		*/
+#define CFG_PCI_PTM2MS		0x00000000	/* disabled		*/
+#define CFG_PCI_PTM2PCI 	0x00000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * Set up values for external bus controller
+ * used by cpu_init.c
+ *-----------------------------------------------------------------------
+ */
+ /* Don't use PerWE instead of PCI_INT ( these functions share a pin ) */
+#undef CONFIG_USE_PERWE
+
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* bank 0 is boot flash */
+/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_W7O_EBC_PB0AP   0x03050440
+/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_W7O_EBC_PB0CR   0xFFE38000
+
+/* bank 1 is main flash */
+/* BME=0,TWT=11,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_EBC_PB1AP   0x05850240
+/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
+#define CFG_EBC_PB1CR   0xF00FC000
+
+/* bank 2 is RTC/NVRAM */
+/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_EBC_PB2AP   0x03000440
+/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_EBC_PB2CR   0xFC018000
+
+/* bank 3 is FPGA 0 */
+/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
+#define CFG_EBC_PB3AP   0x02000400
+/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
+#define CFG_EBC_PB3CR   0xFD01A000
+
+/* bank 4 is FPGA 1 */
+/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
+#define CFG_EBC_PB4AP   0x02000400
+/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_EBC_PB4CR   0xFD11A000
+
+/* bank 5 is FPGA 2 */
+/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
+#define CFG_EBC_PB5AP   0x02000400
+/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
+#define CFG_EBC_PB5CR   0xFD21A000
+
+/* bank 6 is unused */
+/* pb6ap = 0 */
+#define CFG_EBC_PB6AP   0x00000000
+/* pb6cr = 0 */
+#define CFG_EBC_PB6CR   0x00000000
+
+/* bank 7 is LED register */
+/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_W7O_EBC_PB7AP   0x03050440
+/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
+#define CFG_W7O_EBC_PB7CR   0xFE01C000
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2		/* max number of memory banks	*/
+#define CFG_MAX_FLASH_SECT	256		/* max number of sec on 1 chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000		/* Timeout, Flash Erase, in ms	*/
+#define CFG_FLASH_WRITE_TOUT	500		/* Timeout, Flash Write, in ms	*/
+#define CFG_FLASH_PROTECTION	1		/* Use real Flash protection	*/
+
+#if 1 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_IN_NVRAM	1		/* use NVRAM for env vars	*/
+#define CFG_NVRAM_BASE_ADDR	0xfc000000	/* NVRAM base address		*/
+#define CFG_NVRAM_SIZE		(32*1024)	/* NVRAM size			*/
+#define CFG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
+/*define CFG_ENV_ADDR		 \
+	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) Env  */
+#define CFG_ENV_ADDR		CFG_NVRAM_BASE_ADDR
+
+#else /* Use Boot Flash for environment variables */
+/*-----------------------------------------------------------------------
+ * Flash EEPROM for environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
+#define CFG_ENV_SIZE		0x10000		/* Total Size of env. sector	*/
+
+#define CFG_ENV_SECT_SIZE	0x10000		/* see README - env sec tot sze */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC08) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#define CFG_I2C_MULTI_EEPROMS
+/*-----------------------------------------------------------------------
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ */
+#define SPD_EEPROM_ADDRESS      0x50	/* XXX conflicting address!!! XXX */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		8192		/* For IBM 405 CPUs			*/
+#define CFG_CACHELINE_SIZE	32		/* ...		*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
+#endif
+
+/*
+ * Init Memory Controller:
+ */
+#define FLASH_BASE0_PRELIM	0xFFE00000	/* FLASH bank #0		*/
+#define FLASH_BASE1_PRELIM	0xF0000000	/* FLASH bank #1		*/
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in RAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CFG_GBL_DATA_SIZE	64		/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM		0x02		/* Software reboot		*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/
+#endif
+
+/*
+ * FPGA(s) configuration
+ */
+#define CFG_FPGA_IMAGE_LEN	0x80000		/* 512KB FPGA image		*/
+#define CONFIG_NUM_FPGAS	3		/* Number of FPGAs on board	*/
+#define CONFIG_MAX_FPGAS	6		/* Maximum number of FPGAs	*/
+#define CONFIG_FPGAS_BASE	0xFD000000L	/* Base address of FPGAs	*/
+#define CONFIG_FPGAS_BANK_SIZE	0x00100000L	/* FPGAs' mmap bank size	*/
+
+#endif	/* __CONFIG_H */
+
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h
new file mode 100644
index 00000000000..0c06e9181f0
--- /dev/null
+++ b/include/configs/W7OLMG.h
@@ -0,0 +1,326 @@
+/*
+ * (C) Copyright 2001
+ * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP		1		/* This is a PPC405GP CPU	*/
+#define CONFIG_4xx		1		/* ...member of PPC405 family	*/
+#define CONFIG_W7O		1		/* ...on a Wave 7 Optics board	*/
+#define CONFIG_W7OLMG		1		/* ...specifically an LMG	*/
+
+#define CONFIG_BOARD_PRE_INIT	1		/* Call board_pre_init	*/
+
+#define CONFIG_SYS_CLK_FREQ	33333333	/* external frequency to pll	*/
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
+
+#if 1
+#define CONFIG_BOOTCOMMAND	"bootvx"	/* VxWorks boot command		*/
+#else
+#define CONFIG_BOOTCOMMAND	"bootp"		/* autoboot command		*/
+#endif
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_LOADADDR		F0080000
+
+#define CONFIG_ETHADDR		00:06:0D:00:00:00 /* Default, overridden at boot	*/
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_IPADDR		192.168.1.1
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_SERVERIP		192.168.1.2
+
+#define CONFIG_LOADS_ECHO	1		/* echo on for serial download	*/
+#undef CFG_LOADS_BAUD_CHANGE			/* disallow baudrate change	*/
+
+#define CONFIG_MII		1		/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0		/* PHY address			*/
+
+#define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
+#define CONFIG_DTT_LM75     1                /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS  {2, 4}           /* Sensor addresses */
+#define CFG_DTT_MAX_TEMP	70
+#define CFG_DTT_LOW_TEMP	-30
+#define CFG_DTT_HYSTERESIS	3
+
+#define CONFIG_COMMANDS		\
+	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \
+	 CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \
+	 CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO | \
+	 CFG_CMD_DTT)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG				/* watchdog disabled		*/
+#define CONFIG_HW_WATCHDOG			/* HW Watchdog, board specific	*/
+
+#define	CONFIG_SPD_EEPROM			/* SPD EEPROM for SDRAM param.	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_PROMPT		"Wave7Optics> " /* Monitor Command Prompt	*/
+#undef  CFG_HUSH_PARSER				/* No hush parse for U-Boot       */
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2     "> "
+#endif
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size	*/
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
+
+#undef  CFG_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CFG_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD		384000
+
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE	{9600}
+
+#define CFG_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
+#define CFG_EXTBDINFO		1		/* use extended board_info (bd_t) */
+
+#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER	0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE		1		/* configure as pci host	*/
+#define PCI_HOST_AUTO		2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI				/* include pci support		*/
+#define CONFIG_PCI_HOST		PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP				/* pci plug-and-play		*/
+/* resource configuration	*/
+#define CFG_PCI_SUBSYS_VENDORID 0x1014		/* PCI Vendor ID: IBM		*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0156		/* PCI Device ID: 405GP		*/
+#define CFG_PCI_PTM1LA		0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS		0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CFG_PCI_PTM1PCI 	0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA		0x00000000	/* disabled		*/
+#define CFG_PCI_PTM2MS		0x00000000	/* disabled		*/
+#define CFG_PCI_PTM2PCI 	0x00000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * Set up values for external bus controller
+ * used by cpu_init.c
+ *-----------------------------------------------------------------------
+ */
+ /* use PerWE instead of PCI_INT ( these functions share a pin ) */
+#define CONFIG_USE_PERWE 1
+
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* bank 0 is boot flash */
+/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_W7O_EBC_PB0AP   0x03050440
+/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_W7O_EBC_PB0CR   0xFFE38000
+
+/* bank 1 is main flash */
+/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_EBC_PB1AP   0x04850240
+/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
+#define CFG_EBC_PB1CR   0xF00FC000
+
+/* bank 2 is RTC/NVRAM */
+/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_EBC_PB2AP   0x03000440
+/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_EBC_PB2CR   0xFC018000
+
+/* bank 3 is FPGA 0 */
+/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
+#define CFG_EBC_PB3AP   0x02000400
+/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
+#define CFG_EBC_PB3CR   0xFD01A000
+
+/* bank 4 is SAM 8 bit range */
+/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
+#define CFG_EBC_PB4AP   0x02840380
+/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
+#define CFG_EBC_PB4CR   0xFE878000
+
+/* bank 5 is SAM 16 bit range */
+/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */
+#define CFG_EBC_PB5AP   0x05040d80
+/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
+#define CFG_EBC_PB5CR   0xFD87A000
+
+/* bank 6 is unused */
+/* pb6ap = 0 */
+#define CFG_EBC_PB6AP   0x00000000
+/* pb6cr = 0 */
+#define CFG_EBC_PB6CR   0x00000000
+
+/* bank 7 is LED register */
+/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
+#define CFG_W7O_EBC_PB7AP   0x03050440
+/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
+#define CFG_W7O_EBC_PB7CR   0xFE01C000
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 196 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2		/* max number of memory banks	*/
+#define CFG_MAX_FLASH_SECT	256		/* max number of sec on 1 chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000		/* Timeout, Flash Erase, in ms	*/
+#define CFG_FLASH_WRITE_TOUT	500		/* Timeout, Flash Write, in ms	*/
+#define CFG_FLASH_PROTECTION	1		/* Use real Flash protection	*/
+
+#if 1 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_IN_NVRAM	1		/* use NVRAM for env vars	*/
+#define CFG_NVRAM_BASE_ADDR	0xfc000000	/* NVRAM base address		*/
+#define CFG_NVRAM_SIZE		(32*1024)	/* NVRAM size			*/
+#define CFG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
+/*define CFG_ENV_ADDR		 \
+	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) Env  */
+#define CFG_ENV_ADDR		CFG_NVRAM_BASE_ADDR
+
+#else /* Use Boot Flash for environment variables */
+/*-----------------------------------------------------------------------
+ * Flash EEPROM for environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
+#define CFG_ENV_SIZE		0x10000		/* Total Size of env. sector	*/
+
+#define CFG_ENV_SECT_SIZE	0x10000		/* see README - env sec tot sze */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (ATMEL 24C04N)
+ */
+#define CONFIG_HARD_I2C		1		/* Hardware assisted I2C	*/
+#define CFG_I2C_SPEED		400000		/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50		/* EEPROM ATMEL 24C04N		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_I2C_MULTI_EEPROMS
+/*-----------------------------------------------------------------------
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ */
+#define SPD_EEPROM_ADDRESS      0x50	/* XXX conflicting address!!! XXX */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		8192		/* For IBM 405 CPUs			*/
+#define CFG_CACHELINE_SIZE	32		/* ...		*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
+#endif
+
+/*
+ * Init Memory Controller:
+ */
+#define FLASH_BASE0_PRELIM	0xFFE00000	/* FLASH bank #0		*/
+#define FLASH_BASE1_PRELIM	0xF0000000	/* FLASH bank #1		*/
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in RAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CFG_GBL_DATA_SIZE	64		/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM		0x02		/* Software reboot		*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/
+#endif
+
+/*
+ * FPGA(s) configuration
+ */
+#define CFG_FPGA_IMAGE_LEN	0x80000		/* 512KB FPGA image		*/
+#define CONFIG_NUM_FPGAS	1		/* Number of FPGAs on board	*/
+#define CONFIG_MAX_FPGAS	6		/* Maximum number of FPGAs	*/
+#define CONFIG_FPGAS_BASE	0xFD000000L	/* Base address of FPGAs	*/
+#define CONFIG_FPGAS_BANK_SIZE	0x00100000L	/* FPGAs' mmap bank size	*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
new file mode 100644
index 00000000000..fc92d45945b
--- /dev/null
+++ b/include/configs/lwmon.h
@@ -0,0 +1,534 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823		1	/* This is a MPC823E CPU	*/
+#define CONFIG_LWMON		1	/* ...on a LWMON board		*/
+
+#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init		*/
+
+#define CONFIG_LCD		1	/* use LCD controller ...	*/
+#define CONFIG_HLD1045		1	/* ... with a HLD1045 display	*/
+
+#if 1
+#define CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
+#else
+#define CONFIG_8xx_CONS_SCC2
+#endif
+
+#define CONFIG_BAUDRATE		115200	/* with watchdog >= 38400 needed */
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 1 second	*/
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+/* pre-boot commands */
+#define	CONFIG_PREBOOT		"setenv bootdelay 15"
+
+#undef	CONFIG_BOOTARGS
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_CACHE | \
+				 CFG_POST_WATCHDOG | \
+				 CFG_POST_RTC | \
+				 CFG_POST_MEMORY | \
+				 CFG_POST_CPU | \
+				 CFG_POST_UART | \
+				 CFG_POST_ETHER | \
+				 CFG_POST_SPI | \
+				 CFG_POST_USB | \
+				 CFG_POST_SPR)
+
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS						\
+	"kernel_addr=40040000\0"						\
+	"ramdisk_addr=40100000\0"						\
+	"magic_keys=#3\0"							\
+	"key_magic#=28\0"							\
+	"key_cmd#=setenv addfb setenv bootargs \\$(bootargs) console=tty0\0"	\
+	"key_magic3=24\0"							\
+	"key_cmd3=echo *** Entering Test Mode ***;" \
+		"setenv add_misc setenv bootargs \\$(bootargs) testmode\0"	\
+	"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath)\0" \
+	"ramargs=setenv bootargs root=/dev/ram rw\0"				\
+	"addfb=setenv bootargs $(bootargs) console=ttyS1,$(baudrate)\0"		\
+	"addip=setenv bootargs $(bootargs) "					\
+		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off " \
+		"panic=1\0"							\
+	"add_wdt=setenv bootargs $(bootargs) $(wdt_args)\0"			\
+	"flash_nfs=run nfsargs addip add_wdt addfb;"		\
+		"bootm $(kernel_addr)\0"					\
+	"flash_self=run ramargs addip add_wdt addfb;"		\
+		"bootm $(kernel_addr) $(ramdisk_addr)\0"			\
+	"net_nfs=tftp 100000 /tftpboot/pImage.lwmon;"		\
+		"run nfsargs addip add_wdt addfb;bootm\0"	\
+	"rootpath=/opt/eldk/ppc_8xx\0"						\
+	"load=tftp 100000 /tftpboot/u-boot.bin\0"				\
+	"update=protect off 1:0;era 1:0;cp.b 100000 40000000 $(filesize)\0"	\
+	"wdt_args=wdt_8xx=off\0"						\
+	"verify=no"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/
+
+#undef	CONFIG_STATUS_LED		/* Status LED disabled		*/
+
+/* enable I2C and select the hardware/software driver */
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C         	/* I2C bit-banged		*/
+
+#ifdef CONFIG_HARD_I2C
+/*
+ * Hardware (CPM) I2C driver configuration
+ */
+# define CFG_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
+# define CFG_I2C_SLAVE		0xFE
+#endif	/* CONFIG_HARD_I2C */
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(1)	/* 1/4 I2C clock duration */
+#endif	/* CONFIG_SOFT_I2C */
+
+
+#define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+#else
+#define CFG_CMD_POST_DIAG 0
+#endif
+
+#ifdef CONFIG_8xx_CONS_SCC2	/* Can't use ethernet, then */
+#define CONFIG_COMMANDS	     ( (CONFIG_CMD_DFL & ~CFG_CMD_NET) | \
+				CFG_CMD_DATE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_BSP	| \
+				CFG_CMD_POST_DIAG )
+#else
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_BSP	| \
+				CFG_CMD_POST_DIAG )
+#endif
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* enable "hush" shell		*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00100000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x00100000	/* default load address */
+
+#define CFG_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x40000000
+#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE)
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#else
+#define CFG_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
+#endif
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	180000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	600	/* Timeout for Flash Write (in ms)	*/
+
+#if 1
+/* Put environment in flash which is much faster to boot */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR	    0x40040000	/* Address    of Environment Sector	*/
+#define CFG_ENV_SIZE		0x2000	/* Total Size of Environment		*/
+#define CFG_ENV_SECT_SIZE	0x40000 /* we have BIG sectors only :-(		*/
+#else
+/* Environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_ENV_OFFSET		0
+#define CFG_ENV_SIZE		2048
+#endif
+/*-----------------------------------------------------------------------
+ * I2C/EEPROM Configuration
+ */
+
+#define CFG_I2C_AUDIO_ADDR	0x28	/* Audio volume control			*/
+#define CFG_I2C_SYSMON_ADDR	0x2E	/* LM87 System Monitor			*/
+#define CFG_I2C_RTC_ADDR	0x51	/* PCF8563 RTC				*/
+#define CFG_I2C_POWER_A_ADDR	0x52	/* PCMCIA/USB power switch, channel A	*/
+#define CFG_I2C_POWER_B_ADDR	0x53	/* PCMCIA/USB power switch, channel B	*/
+#define CFG_I2C_KEYBD_ADDR	0x56	/* PIC LWE keyboard			*/
+#define CFG_I2C_PICIO_ADDR	0x57	/* PIC IO Expander			*/
+
+#define CONFIG_USE_FRAM			/* Use FRAM instead of EEPROM	*/
+#ifdef CONFIG_USE_FRAM	/* use FRAM */
+#define CFG_I2C_EEPROM_ADDR	0x55	/* FRAM FM24CL64		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	2
+#else			/* use EEPROM */
+#define CFG_I2C_EEPROM_ADDR	0x58	/* EEPROM AT24C164		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec	*/
+#endif	/* CONFIG_USE_FRAM */
+#define CFG_EEPROM_PAGE_WRITE_BITS	4
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if 0 && defined(CONFIG_WATCHDOG)	/* LWMON uses external MAX706TESA WD */
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+/* EARB, DBGC and DBPC are initialised by the HCW */
+/* => 0x000000C0 */
+#define CFG_SIUMCR	(SIUMCR_GB5E)
+/*#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* 0x00405000 */
+#define CFG_PLPRCR_MF	4	/* (4+1) * 13.2 = 66 MHz Clock */
+#define CFG_PLPRCR							\
+		(	(CFG_PLPRCR_MF << PLPRCR_MF_SHIFT) |		\
+			PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST |	\
+			/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL |		\
+			PLPRCR_CSR    /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/	\
+		)
+
+#define CONFIG_8xx_GCLK_FREQ	((CFG_PLPRCR_MF+1)*13200000)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+/* 0x01800000 */
+#define CFG_SCCR	(SCCR_COM00	| /*SCCR_TBS|*/		\
+			 SCCR_RTDIV	|   SCCR_RTSEL	  |	\
+			 /*SCCR_CRQEN|*/  /*SCCR_PRQEN|*/	\
+			 SCCR_EBDF00 |	 SCCR_DFSYNC00 |	\
+			 SCCR_DFBRG00	|   SCCR_DFNL000  |	\
+			 SCCR_DFNH000	|   SCCR_DFLCD100 |	\
+			 SCCR_DFALCD01)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+/* 0x00C3 => 0x0003 */
+#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register		19-4
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0x0000
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ *
+ * Interrupt Levels
+ *-----------------------------------------------------------------------
+ */
+#define CFG_CPM_INTERRUPT	13	/* SIU_LEVEL6	*/
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR	(0x50000000)
+#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR	(0x54000000)
+#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR	(0x58000000)
+#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR	(0x5C000000)
+#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
+
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
+#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
+#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
+
+#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
+#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
+
+#define CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O			*/
+#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers	*/
+#define CFG_ATA_ALT_OFFSET	0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define	CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH) - second Flash bank optional
+ */
+
+#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0x41000000	/* FLASH bank #1	*/
+
+/* used to re-map FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM		0xFF000000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM	0xFF000000	/* OR addr mask */
+
+/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0	*/
+#define CFG_OR_TIMING_FLASH	(OR_SCY_8_CLK)
+
+#define CFG_OR0_REMAP	( CFG_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+				CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \
+				CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
+
+#define CFG_OR1_REMAP	CFG_OR0_REMAP
+#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
+
+/*
+ * BR3/OR3: SDRAM
+ *
+ * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
+ */
+#define SDRAM_BASE3_PRELIM	0x00000000	/* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM	0xF0000000	/* map 256 MB (>SDRAM_MAX_SIZE!) */
+#define SDRAM_TIMING		OR_SCY_0_CLK	/* SDRAM-Timing */
+
+#define SDRAM_MAX_SIZE		0x08000000	/* max 128 MB SDRAM */
+
+#define CFG_OR3_PRELIM	(SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING )
+#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+/*
+ * BR5/OR5: Touch Panel
+ *
+ * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0
+ */
+#define TOUCHPNL_BASE		0x20000000
+#define TOUCHPNL_OR_AM		0xFFFF8000
+#define TOUCHPNL_TIMING		OR_SCY_0_CLK
+
+#define CFG_OR5_PRELIM	(TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+			 TOUCHPNL_TIMING )
+#define CFG_BR5_PRELIM	((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
+
+#define	CFG_MEMORY_75
+#undef	CFG_MEMORY_7E
+#undef	CFG_MEMORY_8E
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MPTPR	0x200
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+#define CFG_MAMR_8COL	0x80802114
+#define CFG_MAMR_9COL	0x80904114
+
+/*
+ * MAR setting for SDRAM
+ */
+#define CFG_MAR		0x00000088
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
new file mode 100644
index 00000000000..95faa417f61
--- /dev/null
+++ b/include/configs/rsdproto.h
@@ -0,0 +1,415 @@
+/*
+ * (C) Copyright 2000
+ * Murray Jensen <Murray.Jensen@cmst.csiro.au>
+ *
+ * (C) Copyright 2000
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the R&S Protocol Board board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
+#define CONFIG_RSD_PROTO	1	/* on a R&S Protocol Board      */
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere.
+ */
+#undef	CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#define	CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef 	CONFIG_CONS_NONE		/* define if console on neither */
+#define CONFIG_CONS_INDEX	1	/* which SMC/SCC channel for console */
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#undef	CONFIG_ETHER_ON_SCC		/* define if ethernet on SCC	*/
+#define	CONFIG_ETHER_ON_FCC		/* define if ethernet on FCC	*/
+#undef	CONFIG_ETHER_NONE		/* define if ethernet on neither */
+#define CONFIG_ETHER_INDEX	2	/* which SCC/FCC channel for ethernet */
+
+#if (CONFIG_ETHER_INDEX == 2)
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - Select bus for bd/buffers (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE	(0)
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
+
+#endif /* CONFIG_ETHER_INDEX */
+
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* enable I2C */
+#define CONFIG_HARD_I2C        	1	/* I2C with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN	50000000	/* in Hz */
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL & ~CFG_CMD_KGDB)
+
+/* Define this if you want to boot from 0x00000100. If you don't define
+ * this, you will need to program the bootloader to 0xfff00000, and
+ * get the hardware reset config words at 0xfe000000. The simplest
+ * way to do that is to program the bootloader at both addresses.
+ * It is suggested that you just let U-Boot live at 0x00000000.
+ */
+#define CFG_RSD_BOOT_LOW 1
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTDELAY	5
+#define CONFIG_BOOTARGS    	"devfs=mount root=ramfs"
+#define CONFIG_ETHADDR		08:00:3e:26:0a:5a
+#define CONFIG_NETMASK          255.255.0.0
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x01c00000	/* 4 ... 28 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+
+#define	CFG_HZ			1000		/* decrementer freq: 1 ms ticks	*/
+
+						/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define PHYS_SDRAM_60X		0x00000000 /* SDRAM (60x Bus) */
+#define PHYS_SDRAM_60X_SIZE	0x08000000 /* 128 MB */
+
+#define PHYS_SDRAM_LOCAL	0x40000000 /* SDRAM (Local Bus) */
+#define PHYS_SDRAM_LOCAL_SIZE	0x04000000 /* 64 MB */
+
+#define PHYS_DPRAM_PCI       	0xE8000000 /* DPRAM PPC/PCI */
+#define PHYS_DPRAM_PCI_SIZE   	0x00020000 /* 128 KB */
+
+/*#define PHYS_DPRAM_PCI_SEM	0x04020000 / * DPRAM PPC/PCI Semaphore */
+/*#define PHYS_DPRAM_PCI_SEM_SIZE	0x00000001 / * 1 Byte */
+
+#define PHYS_DPRAM_SHARC       	0xE8100000 /* DPRAM PPC/Sharc */
+#define PHYS_DPRAM_SHARC_SIZE 	0x00040000 /* 256 KB */
+
+/*#define PHYS_DPRAM_SHARC_SEM	0x04140000 / * DPRAM PPC/Sharc Semaphore */
+/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */
+
+#define PHYS_VIRTEX_REGISTER    0xE8300000 /* FPGA implemented register */
+#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100
+
+#define PHYS_USB		0x04200000 /* USB Controller (60x Bus) */
+#define PHYS_USB_SIZE		0x00000002 /* 2 Bytes */
+
+#define PHYS_IMMR		0xF0000000 /* Internal Memory Mapped Reg. */
+
+#define PHYS_FLASH		0xFF000000 /* Flash (60x Bus) */
+#define PHYS_FLASH_SIZE		0x01000000 /* 16 MB */
+
+#define CFG_IMMR		PHYS_IMMR
+
+/*-----------------------------------------------------------------------
+ * Reset Address
+ *
+ * In order to reset the CPU, U-Boot jumps to a special address which
+ * causes a machine check exception. The default address for this is
+ * CFG_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when
+ * testing the monitor in RAM using a JTAG debugger.
+ *
+ * Just set CFG_RESET_ADDRESS to an address that you know is sure to
+ * cause a bus error on your hardware.
+ */
+#define CFG_RESET_ADDRESS	0x20000000
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ */
+
+#if defined(CFG_RSD_BOOT_LOW)
+#  define  CFG_RSD_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
+#else
+#  define  CFG_RSD_HRCW_BOOT_FLAGS  (0)
+#endif /* defined(CFG_RSD_BOOT_LOW) */
+
+/* get the HRCW ISB field from CFG_IMMR */
+#define CFG_RSD_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\
+                            ((CFG_IMMR & 0x01000000) >> 7)  |\
+                            ((CFG_IMMR & 0x00100000) >> 4) )
+
+#define CFG_HRCW_MASTER	(HRCW_L2CPC10 | \
+			 HRCW_DPPC11 | \
+                         CFG_RSD_HRCW_IMMR |\
+		     	 HRCW_MMR00 | \
+	     		 HRCW_APPC10 | \
+		     	 HRCW_CS10PC00 | \
+		     	 HRCW_MODCK_H0000 |\
+			 CFG_RSD_HRCW_BOOT_FLAGS)
+
+/* no slaves */
+#define CFG_HRCW_SLAVE1	0
+#define CFG_HRCW_SLAVE2	0
+#define CFG_HRCW_SLAVE3	0
+#define CFG_HRCW_SLAVE4	0
+#define CFG_HRCW_SLAVE5	0
+#define CFG_HRCW_SLAVE6	0
+#define CFG_HRCW_SLAVE7	0
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Note also that the logic that sets CFG_RAMBOOT is platform dependend.
+ */
+#define	CFG_SDRAM_BASE		PHYS_SDRAM_60X
+#define CFG_FLASH_BASE		PHYS_FLASH
+/*#define	CFG_MONITOR_BASE	0x200000 */
+#define	CFG_MONITOR_BASE	CFG_FLASH_BASE
+#if CFG_MONITOR_BASE < CFG_FLASH_BASE
+#define CFG_RAMBOOT
+#endif
+#define	CFG_MONITOR_LEN		(160 << 10)	/* Reserve 160 kB for Monitor	*/
+#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	63	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	12000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	3000	/* Timeout for Flash Write (in ms)	*/
+
+/* turn off NVRAM env feature */
+#undef CONFIG_NVRAM_ENV
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR	(PHYS_FLASH + 0x28000)	/* Addr of Environment Sector	*/
+#define CFG_ENV_SECT_SIZE	0x8000	/* Total Size of Environment Sector	*/
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers			 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL	(HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP)
+#define CFG_HID2	0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMR		0
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration					 4-25
+ *-----------------------------------------------------------------------
+ */
+#define CFG_BCR		0x100c0000
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				 4-31
+ *-----------------------------------------------------------------------
+ */
+
+#define CFG_SIUMCR	(SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \
+					 SIUMCR_CS10PC01 | SIUMCR_BCTLC01)
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \
+			 SYPCR_SWRI | SYPCR_SWP)
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control			 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC	(TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control					 9-8
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SCCR	0x00000000
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration				13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR	0
+
+/*
+ * Init Memory Controller:
+ */
+
+#define CFG_PSDMR	0x494D2452
+#define CFG_LSDMR	0x49492552
+
+/* Flash */
+#define CFG_BR0_PRELIM	(PHYS_FLASH | BRx_V)
+#define CFG_OR0_PRELIM	(P2SZ_TO_AM(PHYS_FLASH_SIZE) | \
+			 ORxG_BCTLD | \
+			 ORxG_SCY_5_CLK)
+
+/* DPRAM to the PCI BUS on the protocol board */
+#define CFG_BR1_PRELIM	(PHYS_DPRAM_PCI | BRx_V)
+#define CFG_OR1_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \
+			 ORxG_ACS_DIV4)
+
+/* 60x Bus SDRAM */
+#define CFG_BR2_PRELIM	(PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V)
+#define CFG_OR2_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \
+			 ORxS_BPD_4 | \
+			 ORxS_ROWST_PBI1_A2 | \
+			 ORxS_NUMR_13 | \
+			 ORxS_IBID)
+
+/* Virtex-FPGA - Register */
+#define CFG_BR3_PRELIM  (PHYS_VIRTEX_REGISTER | BRx_V)
+#define CFG_OR3_PRELIM  (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \
+                         ORxG_SCY_1_CLK | \
+                         ORxG_ACS_DIV2 | \
+                         ORxG_CSNT )
+
+/* local bus SDRAM */
+#define CFG_BR4_PRELIM	(PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V)
+#define CFG_OR4_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \
+			 ORxS_BPD_4 | \
+			 ORxS_ROWST_PBI1_A4 | \
+			 ORxS_NUMR_13)
+
+/* DPRAM to the Sharc-Bus on the protocol board */
+#define CFG_BR5_PRELIM	(PHYS_DPRAM_SHARC | BRx_V)
+#define CFG_OR5_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \
+			 ORxG_ACS_DIV4)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
new file mode 100644
index 00000000000..a3a7ec35295
--- /dev/null
+++ b/include/linux/mtd/nand.h
@@ -0,0 +1,87 @@
+/*
+ *  u-boot/include/linux/mtd/nand.h
+ *
+ *  Copyright (c) 2000 David Woodhouse <dwmw2@mvhi.com>
+ *                     Steven J. Hill <sjhill@cotw.com>
+ *
+ * $Id: nand.h,v 1.8 2000/10/30 17:16:17 sjhill Exp $
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  Info:
+ *   Contains standard defines and IDs for NAND flash devices
+ *
+ *  Changelog:
+ *   01-31-2000 DMW     Created
+ *   09-18-2000 SJH     Moved structure out of the Disk-On-Chip drivers
+ *			so it can be used by other NAND flash device
+ *			drivers. I also changed the copyright since none
+ *			of the original contents of this file are specific
+ *			to DoC devices. David can whack me with a baseball
+ *			bat later if I did something naughty.
+ *   10-11-2000 SJH     Added private NAND flash structure for driver
+ *   10-24-2000 SJH     Added prototype for 'nand_scan' function
+ */
+#ifndef __LINUX_MTD_NAND_H
+#define __LINUX_MTD_NAND_H
+
+/*
+ * Standard NAND flash commands
+ */
+#define NAND_CMD_READ0		0
+#define NAND_CMD_READ1		1
+#define NAND_CMD_PAGEPROG	0x10
+#define NAND_CMD_READOOB	0x50
+#define NAND_CMD_ERASE1		0x60
+#define NAND_CMD_STATUS		0x70
+#define NAND_CMD_SEQIN		0x80
+#define NAND_CMD_READID		0x90
+#define NAND_CMD_ERASE2		0xd0
+#define NAND_CMD_RESET		0xff
+
+/*
+ * NAND Flash Manufacturer ID Codes
+ */
+#define NAND_MFR_TOSHIBA	0x98
+#define NAND_MFR_SAMSUNG	0xec
+
+/*
+ * NAND Flash Device ID Structure
+ *
+ * Structure overview:
+ *
+ *  name - Complete name of device
+ *
+ *  manufacture_id - manufacturer ID code of device.
+ *
+ *  model_id - model ID code of device.
+ *
+ *  chipshift - total number of address bits for the device which
+ *              is used to calculate address offsets and the total
+ *              number of bytes the device is capable of.
+ *
+ *  page256 - denotes if flash device has 256 byte pages or not.
+ *
+ *  pageadrlen - number of bytes minus one needed to hold the
+ *               complete address into the flash array. Keep in
+ *               mind that when a read or write is done to a
+ *               specific address, the address is input serially
+ *               8 bits at a time. This structure member is used
+ *               by the read/write routines as a loop index for
+ *               shifting the address out 8 bits at a time.
+ *
+ *  erasesize - size of an erase block in the flash device.
+ */
+struct nand_flash_dev {
+	char * name;
+	int manufacture_id;
+	int model_id;
+	int chipshift;
+	char page256;
+	char pageadrlen;
+	unsigned long erasesize;
+};
+
+#endif /* __LINUX_MTD_NAND_H */
diff --git a/include/linux/mtd/nand_ids.h b/include/linux/mtd/nand_ids.h
new file mode 100644
index 00000000000..6b733be081d
--- /dev/null
+++ b/include/linux/mtd/nand_ids.h
@@ -0,0 +1,52 @@
+/*
+ *  u-boot/include/linux/mtd/nand_ids.h
+ *
+ *  Copyright (c) 2000 David Woodhouse <dwmw2@mvhi.com>
+ *                     Steven J. Hill <sjhill@cotw.com>
+ *
+ * $Id: nand_ids.h,v 1.1 2000/10/13 16:16:26 mdeans Exp $
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  Info:
+ *   Contains standard defines and IDs for NAND flash devices
+ *
+ *  Changelog:
+ *   01-31-2000 DMW     Created
+ *   09-18-2000 SJH     Moved structure out of the Disk-On-Chip drivers
+ *			so it can be used by other NAND flash device
+ *			drivers. I also changed the copyright since none
+ *			of the original contents of this file are specific
+ *			to DoC devices. David can whack me with a baseball
+ *			bat later if I did something naughty.
+ *   10-11-2000 SJH     Added private NAND flash structure for driver
+ *   2000-10-13 BE      Moved out of 'nand.h' - avoids duplication.
+ */
+
+#ifndef __LINUX_MTD_NAND_IDS_H
+#define __LINUX_MTD_NAND_IDS_H
+
+static struct nand_flash_dev nand_flash_ids[] = {
+	{"Toshiba TC5816BDC",     NAND_MFR_TOSHIBA, 0x64, 21, 1, 2, 0x1000},
+	{"Toshiba TC5832DC",      NAND_MFR_TOSHIBA, 0x6b, 22, 0, 2, 0x2000},
+	{"Toshiba TH58V128DC",    NAND_MFR_TOSHIBA, 0x73, 24, 0, 2, 0x4000},
+	{"Toshiba TC58256FT/DC",  NAND_MFR_TOSHIBA, 0x75, 25, 0, 2, 0x4000},
+	{"Toshiba TH58512FT",     NAND_MFR_TOSHIBA, 0x76, 26, 0, 3, 0x4000},
+	{"Toshiba TC58V32DC",     NAND_MFR_TOSHIBA, 0xe5, 22, 0, 2, 0x2000},
+	{"Toshiba TC58V64AFT/DC", NAND_MFR_TOSHIBA, 0xe6, 23, 0, 2, 0x2000},
+	{"Toshiba TC58V16BDC",    NAND_MFR_TOSHIBA, 0xea, 21, 1, 2, 0x1000},
+	{"Samsung KM29N16000",    NAND_MFR_SAMSUNG, 0x64, 21, 1, 2, 0x1000},
+	{"Samsung unknown 4Mb",   NAND_MFR_SAMSUNG, 0x6b, 22, 0, 2, 0x2000},
+	{"Samsung KM29U128T",     NAND_MFR_SAMSUNG, 0x73, 24, 0, 2, 0x4000},
+	{"Samsung KM29U256T",     NAND_MFR_SAMSUNG, 0x75, 25, 0, 2, 0x4000},
+	{"Samsung unknown 64Mb",  NAND_MFR_SAMSUNG, 0x76, 26, 0, 3, 0x4000},
+	{"Samsung KM29W32000",    NAND_MFR_SAMSUNG, 0xe3, 22, 0, 2, 0x2000},
+	{"Samsung unknown 4Mb",   NAND_MFR_SAMSUNG, 0xe5, 22, 0, 2, 0x2000},
+	{"Samsung KM29U64000",    NAND_MFR_SAMSUNG, 0xe6, 23, 0, 2, 0x2000},
+	{"Samsung KM29W16000",    NAND_MFR_SAMSUNG, 0xea, 21, 1, 2, 0x1000},
+	{NULL,}
+};
+
+#endif /* __LINUX_MTD_NAND_IDS_H */