Merge branch 'master' of git://www.denx.de/git/u-boot-imx

49 files changed, 2442 insertions, 92 deletions

diff --git a/arch/arm/cpu/arm926ejs/mx27/reset.c b/arch/arm/cpu/arm926ejs/mx27/reset.c
index f7b4a1c83e3..e7649867372 100644
--- a/arch/arm/cpu/arm926ejs/mx27/reset.c
+++ b/arch/arm/cpu/arm926ejs/mx27/reset.c
@@ -27,14 +27,14 @@ void reset_cpu(ulong ignored)
 {
 	struct wdog_regs *regs = (struct wdog_regs *)IMX_WDT_BASE;
 	/* Disable watchdog and set Time-Out field to 0 */
-	writel(0x00000000, &regs->wcr);
+	writew(0x0000, &regs->wcr);
 
 	/* Write Service Sequence */
-	writel(0x00005555, &regs->wsr);
-	writel(0x0000AAAA, &regs->wsr);
+	writew(0x5555, &regs->wsr);
+	writew(0xAAAA, &regs->wsr);
 
 	/* Enable watchdog */
-	writel(WCR_WDE, &regs->wcr);
+	writew(WCR_WDE, &regs->wcr);
 
 	while (1);
 	/*NOTREACHED*/
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index c72a1508751..1bcd3990933 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -60,6 +60,18 @@ config TARGET_CM_FX6
 config TARGET_EMBESTMX6BOARDS
 	bool "embestmx6boards"
 
+config TARGET_GE_B450V3
+	bool "General Electric B450v3"
+	select MX6Q
+
+config TARGET_GE_B650V3
+	bool "General Electric B650v3"
+	select MX6Q
+
+config TARGET_GE_B850V3
+	bool "General Electric B850v3"
+	select MX6Q
+
 config TARGET_GW_VENTANA
 	bool "gw_ventana"
 	select SUPPORT_SPL
@@ -92,12 +104,14 @@ config TARGET_MX6SLEVK
 
 config TARGET_MX6SXSABRESD
 	bool "mx6sxsabresd"
+	select MX6SX
 	select SUPPORT_SPL
 	select DM
 	select DM_THERMAL
 
 config TARGET_MX6SXSABREAUTO
         bool "mx6sxsabreauto"
+	select MX6SX
         select DM
         select DM_THERMAL
 
@@ -153,16 +167,25 @@ config TARGET_WANDBOARD
 config TARGET_WARP
 	bool "WaRP"
 
+config TARGET_XPRESS
+	bool "CCV xPress"
+	select MX6UL
+	select DM
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 endchoice
 
 config SYS_SOC
 	default "mx6"
 
+source "board/ge/bx50v3/Kconfig"
 source "board/aristainetos/Kconfig"
 source "board/bachmann/ot1200/Kconfig"
 source "board/barco/platinum/Kconfig"
 source "board/barco/titanium/Kconfig"
 source "board/boundary/nitrogen6x/Kconfig"
+source "board/ccv/xpress/Kconfig"
 source "board/compulab/cm_fx6/Kconfig"
 source "board/congatec/cgtqmx6eval/Kconfig"
 source "board/embest/mx6boards/Kconfig"
diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index 88380a6cd90..3b53842e407 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -1183,6 +1183,7 @@ int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	printf("PLL_NET    %8d MHz\n", freq / 1000000);
 
 	printf("\n");
+	printf("ARM        %8d kHz\n", mxc_get_clock(MXC_ARM_CLK) / 1000);
 	printf("IPG        %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
 	printf("UART       %8d kHz\n", mxc_get_clock(MXC_UART_CLK) / 1000);
 #ifdef CONFIG_MXC_SPI
diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
index e457febf678..1e7ae289337 100644
--- a/arch/arm/cpu/armv7/mx6/ddr.c
+++ b/arch/arm/cpu/armv7/mx6/ddr.c
@@ -12,40 +12,20 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/io.h>
 #include <asm/types.h>
+#include <wait_bit.h>
 
 #if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
 
-static int wait_for_bit(void *reg, const uint32_t mask, bool set)
-{
-	unsigned int timeout = 1000;
-	u32 val;
-
-	while (--timeout) {
-		val = readl(reg);
-		if (!set)
-			val = ~val;
-
-		if ((val & mask) == mask)
-			return 0;
-
-		udelay(1);
-	}
-
-	printf("%s: Timeout (reg=%p mask=%08x wait_set=%i)\n",
-	      __func__, reg, mask, set);
-	hang();	/* DRAM couldn't be calibrated, game over :-( */
-}
-
 static void reset_read_data_fifos(void)
 {
 	struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
 
 	/* Reset data FIFOs twice. */
 	setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
-	wait_for_bit(&mmdc0->mpdgctrl0, 1 << 31, 0);
+	wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0);
 
 	setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
-	wait_for_bit(&mmdc0->mpdgctrl0, 1 << 31, 0);
+	wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0);
 }
 
 static void precharge_all(const bool cs0_enable, const bool cs1_enable)
@@ -60,12 +40,12 @@ static void precharge_all(const bool cs0_enable, const bool cs1_enable)
 	 */
 	if (cs0_enable) { /* CS0 */
 		writel(0x04008050, &mmdc0->mdscr);
-		wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
+		wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0);
 	}
 
 	if (cs1_enable) { /* CS1 */
 		writel(0x04008058, &mmdc0->mdscr);
-		wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
+		wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0);
 	}
 }
 
@@ -164,7 +144,7 @@ int mmdc_do_write_level_calibration(void)
 	 * 7. Upon completion of this process the MMDC de-asserts
 	 * the MPWLGCR[HW_WL_EN]
 	 */
-	wait_for_bit(&mmdc0->mpwlgcr, 1 << 0, 0);
+	wait_for_bit("MMDC", &mmdc0->mpwlgcr, 1 << 0, 0, 100, 0);
 
 	/*
 	 * 8. check for any errors: check both PHYs for x64 configuration,
@@ -289,7 +269,7 @@ int mmdc_do_dqs_calibration(void)
 		writel(0x00008028, &mmdc0->mdscr);
 
 	/* poll to make sure the con_ack bit was asserted */
-	wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
+	wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0);
 
 	/*
 	 * Check MDMISC register CALIB_PER_CS to see which CS calibration
@@ -327,7 +307,7 @@ int mmdc_do_dqs_calibration(void)
 	 * this bit until it clears to indicate completion of the write access.
 	 */
 	setbits_le32(&mmdc0->mpswdar0, 1);
-	wait_for_bit(&mmdc0->mpswdar0, 1 << 0, 0);
+	wait_for_bit("MMDC", &mmdc0->mpswdar0, 1 << 0, 0, 100, 0);
 
 	/* Set the RD_DL_ABS# bits to their default values
 	 * (will be calibrated later in the read delay-line calibration).
@@ -372,7 +352,7 @@ int mmdc_do_dqs_calibration(void)
 	setbits_le32(&mmdc0->mpdgctrl0, 5 << 28);
 
 	/* Poll for completion.  MPDGCTRL0[HW_DG_EN] should be 0 */
-	wait_for_bit(&mmdc0->mpdgctrl0, 1 << 28, 0);
+	wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 28, 0, 100, 0);
 
 	/*
 	 * Check to see if any errors were encountered during calibration
@@ -431,7 +411,7 @@ int mmdc_do_dqs_calibration(void)
 	 * setting MPRDDLHWCTL[HW_RD_DL_EN] = 0.   Also, ensure that
 	 * no error bits were set.
 	 */
-	wait_for_bit(&mmdc0->mprddlhwctl, 1 << 4, 0);
+	wait_for_bit("MMDC", &mmdc0->mprddlhwctl, 1 << 4, 0, 100, 0);
 
 	/* check both PHYs for x64 configuration, if x32, check only PHY0 */
 	if (readl(&mmdc0->mprddlhwctl) & 0x0000000f)
@@ -484,7 +464,7 @@ int mmdc_do_dqs_calibration(void)
 	 * by setting MPWRDLHWCTL[HW_WR_DL_EN] = 0.
 	 * Also, ensure that no error bits were set.
 	 */
-	wait_for_bit(&mmdc0->mpwrdlhwctl, 1 << 4, 0);
+	wait_for_bit("MMDC", &mmdc0->mpwrdlhwctl, 1 << 4, 0, 100, 0);
 
 	/* Check both PHYs for x64 configuration, if x32, check only PHY0 */
 	if (readl(&mmdc0->mpwrdlhwctl) & 0x0000000f)
@@ -532,7 +512,7 @@ int mmdc_do_dqs_calibration(void)
 	writel(0x0, &mmdc0->mdscr);	/* CS0 */
 
 	/* Poll to make sure the con_ack bit is clear */
-	wait_for_bit(&mmdc0->mdscr, 1 << 14, 0);
+	wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 0, 100, 0);
 
 	/*
 	 * Print out the registers that were updated as a result
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index 91a3debe910..d4b22ad7f31 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -278,7 +278,10 @@ static void clear_mmdc_ch_mask(void)
 	reg = readl(&mxc_ccm->ccdr);
 
 	/* Clear MMDC channel mask */
-	reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK);
+	if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) || is_cpu_type(MXC_CPU_MX6SL))
+		reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK);
+	else
+		reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK);
 	writel(reg, &mxc_ccm->ccdr);
 }
 
@@ -325,15 +328,30 @@ int arch_cpu_init(void)
 	 */
 	init_bandgap();
 
-	/*
-	 * When low freq boot is enabled, ROM will not set AHB
-	 * freq, so we need to ensure AHB freq is 132MHz in such
-	 * scenario.
-	 */
-	if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
-		set_ahb_rate(132000000);
+	if (!IS_ENABLED(CONFIG_MX6UL)) {
+		/*
+		 * When low freq boot is enabled, ROM will not set AHB
+		 * freq, so we need to ensure AHB freq is 132MHz in such
+		 * scenario.
+		 *
+		 * To i.MX6UL, when power up, default ARM core and
+		 * AHB rate is 396M and 132M.
+		 */
+		if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
+			set_ahb_rate(132000000);
+	}
+
+	if (IS_ENABLED(CONFIG_MX6UL) && is_soc_rev(CHIP_REV_1_0) == 0) {
+		/*
+		 * According to the design team's requirement on i.MX6UL,
+		 * the PMIC_STBY_REQ PAD should be configured as open
+		 * drain 100K (0x0000b8a0).
+		 * Only exists on TO1.0
+		 */
+		writel(0x0000b8a0, IOMUXC_BASE_ADDR + 0x29c);
+	}
 
-		/* Set perclk to source from OSC 24MHz */
+	/* Set perclk to source from OSC 24MHz */
 #if defined(CONFIG_MX6SL)
 	set_preclk_from_osc();
 #endif
diff --git a/arch/arm/cpu/armv7/mx7/Kconfig b/arch/arm/cpu/armv7/mx7/Kconfig
index 97d62389fdc..ecfa4a2c356 100644
--- a/arch/arm/cpu/armv7/mx7/Kconfig
+++ b/arch/arm/cpu/armv7/mx7/Kconfig
@@ -15,6 +15,13 @@ choice
 
 config TARGET_MX7DSABRESD
 	bool "mx7dsabresd"
+	select MX7D
+	select DM
+	select DM_THERMAL
+
+config TARGET_WARP7
+	bool "warp7"
+	select MX7D
 	select DM
 	select DM_THERMAL
 
@@ -24,5 +31,6 @@ config SYS_SOC
 	default "mx7"
 
 source "board/freescale/mx7dsabresd/Kconfig"
+source "board/warp7/Kconfig"
 
 endif
diff --git a/arch/arm/cpu/armv7/mx7/soc.c b/arch/arm/cpu/armv7/mx7/soc.c
index ba6cfb9dce7..073bbc6d014 100644
--- a/arch/arm/cpu/armv7/mx7/soc.c
+++ b/arch/arm/cpu/armv7/mx7/soc.c
@@ -165,6 +165,21 @@ u32 get_cpu_temp_grade(int *minc, int *maxc)
 	return val;
 }
 
+static bool is_mx7d(void)
+{
+	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
+	struct fuse_bank *bank = &ocotp->bank[1];
+	struct fuse_bank1_regs *fuse =
+		(struct fuse_bank1_regs *)bank->fuse_regs;
+	int val;
+
+	val = readl(&fuse->tester4);
+	if (val & 1)
+		return false;
+	else
+		return true;
+}
+
 u32 get_cpu_rev(void)
 {
 	struct mxc_ccm_anatop_reg *ccm_anatop = (struct mxc_ccm_anatop_reg *)
@@ -172,6 +187,9 @@ u32 get_cpu_rev(void)
 	u32 reg = readl(&ccm_anatop->digprog);
 	u32 type = (reg >> 16) & 0xff;
 
+	if (!is_mx7d())
+		type = MXC_CPU_MX7S;
+
 	reg &= 0xff;
 	return (type << 12) | reg;
 }
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 656bb60bbe2..5fb3ed840f8 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -137,6 +137,8 @@ unsigned imx_ddr_size(void)
 const char *get_imx_type(u32 imxtype)
 {
 	switch (imxtype) {
+	case MXC_CPU_MX7S:
+		return "7SOLO";	/* Single-core version of the mx7 */
 	case MXC_CPU_MX7D:
 		return "7D";	/* Dual-core version of the mx7 */
 	case MXC_CPU_MX6QP:
diff --git a/arch/arm/include/asm/arch-imx/cpu.h b/arch/arm/include/asm/arch-imx/cpu.h
index 8a75902ee5d..7c63c13d7b5 100644
--- a/arch/arm/include/asm/arch-imx/cpu.h
+++ b/arch/arm/include/asm/arch-imx/cpu.h
@@ -21,6 +21,7 @@
 #define MXC_CPU_MX6D		0x67
 #define MXC_CPU_MX6DP		0x68
 #define MXC_CPU_MX6QP		0x69
+#define MXC_CPU_MX7S		0x71 /* dummy ID */
 #define MXC_CPU_MX7D		0x72
 #define MXC_CPU_VF610		0xF6 /* dummy ID */
 
diff --git a/arch/arm/include/asm/arch-mx27/imx-regs.h b/arch/arm/include/asm/arch-mx27/imx-regs.h
index baf1d29cc3e..40b76d26f6d 100644
--- a/arch/arm/include/asm/arch-mx27/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx27/imx-regs.h
@@ -106,9 +106,9 @@ struct esdramc_regs {
 
 /* Watchdog Registers*/
 struct wdog_regs {
-	u32 wcr;
-	u32 wsr;
-	u32 wstr;
+	u16 wcr;
+	u16 wsr;
+	u16 wstr;
 };
 
 /* PLL registers */
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index f3c26dc6e6e..53488bef552 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -162,6 +162,7 @@
 #endif
 #define UART1_BASE                  (ATZ1_BASE_ADDR + 0x20000)
 #define ESAI1_BASE_ADDR             (ATZ1_BASE_ADDR + 0x24000)
+#define UART8_BASE                  (ATZ1_BASE_ADDR + 0x24000)
 #define SSI1_BASE_ADDR              (ATZ1_BASE_ADDR + 0x28000)
 #define SSI2_BASE_ADDR              (ATZ1_BASE_ADDR + 0x2C000)
 #define SSI3_BASE_ADDR              (ATZ1_BASE_ADDR + 0x30000)
diff --git a/board/ccv/xpress/Kconfig b/board/ccv/xpress/Kconfig
new file mode 100644
index 00000000000..9157013c306
--- /dev/null
+++ b/board/ccv/xpress/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_XPRESS
+
+config SYS_BOARD
+	default "xpress"
+
+config SYS_VENDOR
+	default "ccv"
+
+config SYS_CONFIG_NAME
+	default "xpress"
+
+endif
diff --git a/board/ccv/xpress/MAINTAINERS b/board/ccv/xpress/MAINTAINERS
new file mode 100644
index 00000000000..e242bfb2065
--- /dev/null
+++ b/board/ccv/xpress/MAINTAINERS
@@ -0,0 +1,7 @@
+CCV XPRESS BOARD
+M:	Stefan Roese <sr@denx.de>
+S:	Maintained
+F:	board/ccv/xpress/
+F:	include/configs/xpress.h
+F:	configs/xpress_defconfig
+F:	configs/xpress_spl_defconfig
diff --git a/board/ccv/xpress/Makefile b/board/ccv/xpress/Makefile
new file mode 100644
index 00000000000..0d444b6c553
--- /dev/null
+++ b/board/ccv/xpress/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := xpress.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/ccv/xpress/imximage.cfg b/board/ccv/xpress/imximage.cfg
new file mode 100644
index 00000000000..92167c98eef
--- /dev/null
+++ b/board/ccv/xpress/imximage.cfg
@@ -0,0 +1,176 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * sd, nand
+ */
+BOOT_FROM      sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* ddr io type */
+DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+
+/* clock */
+DATA 4 0x020e027c 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */
+
+/* control and address */
+DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be
+				configured using Group Control Register:
+				IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
+DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
+DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+
+/* data strobes */
+DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */
+DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */
+
+/* data */
+DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+
+/*
+ * DDR Controller Registers
+ *
+ * Manufacturer:  IM
+ * Device Part Number:  IME1G16D3EEBG-15EI
+ * Clock Freq.:   400MHz
+ * Density per CS in Gb: 1
+ * Chip Selects used: 1
+ * Number of Banks: 8
+ * Row address:     13
+ * Column address:  10
+ * Data bus width 16
+ */
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+				during MMDC set up */
+
+/*
+ * Calibration setup
+ */
+DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both one-time &
+				periodic HW ZQ calibration. */
+
+/*
+ * For target board, may need to run write leveling calibration to fine tune
+ * these settings.
+ */
+DATA 4 0x021b080c 0x00000000
+
+/* Read DQS Gating calibration */
+DATA 4 0x021b083c 0x4164015C /* MPDGCTRL0 PHY0 */
+
+/* Read calibration */
+DATA 4 0x021b0848 0x40404446 /* MPRDDLCTL PHY0 */
+
+/* Write calibration */
+DATA 4 0x021b0850 0x40405A52 /* MPWRDLCTL PHY0 */
+
+/*
+ * read data bit delay: (3 is the reccommended default value, although out of
+ * reset value is 0)
+ */
+DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */
+DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */
+DATA 4 0x021b082c 0xF3333333
+DATA 4 0x021b0830 0xF3333333
+
+DATA 4 0x021b08c0 0x00921012
+
+/* Clock Fine Tuning */
+DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK Control Register */
+
+/* Complete calibration by forced measurement: */
+DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
+/*
+ * Calibration setup end
+ */
+
+/* MMDC init: */
+DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */
+DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */
+DATA 4 0x021b000c 0x3F4352F3 /* MMDC0_MDCFG0 */
+DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */
+DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */
+
+/*
+ * MDMISC: RALAT kept to the high level of 5.
+ * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ * Lower RALAT benefits:
+ * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT
+ *    to 3
+ * b. Small performence improvment
+ */
+DATA 4 0x021b0018 0x00201740 /* MMDC0_MDMISC */
+
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+				during MMDC set up */
+
+DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */
+DATA 4 0x021b0030 0x00431023 /* MMDC0_MDOR */
+DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */
+DATA 4 0x021b0000 0x82180000 /* MMDC0_MDCTL */
+
+/* Mode register writes */
+DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
+DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
+DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
+DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
+DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to
+				device on CS0 */
+
+DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
+DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
+DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down enabled */
+DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled, MMDC will
+				enter automatically to self-refresh while the
+				number of idle cycle reached. */
+DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register (especially
+				the configuration bit as initialization is
+				complete) */
diff --git a/board/ccv/xpress/spl.c b/board/ccv/xpress/spl.c
new file mode 100644
index 00000000000..d15b8429baa
--- /dev/null
+++ b/board/ccv/xpress/spl.c
@@ -0,0 +1,116 @@
+/*
+ * SPL specific code for CCV xPress
+ *
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/crm_regs.h>
+
+/* Configuration for IM IME1G16D3EEBG-15EI, 64M x 16 -> 128MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000008,
+	.dram_sdqs0 = 0x00000038,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x4164015C,
+	.p0_mprddlctl = 0x40404446,
+	.p0_mpwrdlctl = 0x40405A52,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 13,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* Setup iomux and i2c */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+}
diff --git a/board/ccv/xpress/xpress.c b/board/ccv/xpress/xpress.c
new file mode 100644
index 00000000000..6fc76cd1564
--- /dev/null
+++ b/board/ccv/xpress/xpress.c
@@ -0,0 +1,331 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ul_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-fsl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_HIGH   |                                  \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
+
+#define MDIO_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm | PAD_CTL_HYS |			\
+	PAD_CTL_SRE_FAST)
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
+		.gp = IMX_GPIO_NR(1, 2),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
+		.gp = IMX_GPIO_NR(1, 3),
+	},
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_GPIO1_IO00__I2C2_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO00 | PC,
+		.gp = IMX_GPIO_NR(1, 0),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C2_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO01 | PC,
+		.gp = IMX_GPIO_NR(1, 1),
+	},
+};
+
+static struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode =  MX6_PAD_UART2_TX_DATA__I2C4_SCL | PC,
+		.gpio_mode = MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | PC,
+		.gp = IMX_GPIO_NR(1, 20),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_UART2_RX_DATA__I2C4_SDA | PC,
+		.gpio_mode = MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | PC,
+		.gp = IMX_GPIO_NR(1, 21),
+	},
+};
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+	MX6_PAD_GPIO1_IO04__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO05__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart8_pads[] = {
+	MX6_PAD_ENET2_TX_DATA1__UART8_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__UART8_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__UART8_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__UART8_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+	imx_iomux_v3_setup_multiple_pads(uart8_pads, ARRAY_SIZE(uart8_pads));
+}
+
+/* eMMC on USDHC2 */
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*
+	 * RST_B
+	 */
+	MX6_PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg = {
+	.esdhc_base = USDHC2_BASE_ADDR,
+	.max_bus_width = 8,
+};
+
+#define USDHC2_PWR_GPIO	IMX_GPIO_NR(1, 9)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* eMMC is always present */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+
+	usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+
+#define USB_OTHERREGS_OFFSET	0x800
+#define UCTRL_PWR_POL		(1 << 9)
+
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	/* OTG1 */
+	MX6_PAD_SD1_CMD__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+	/* OTG2 */
+	MX6_PAD_SD1_DATA1__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__ANATOP_OTG2_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+};
+
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+					 ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+
+int board_ehci_hcd_init(int port)
+{
+	u32 *usbnc_usb_ctrl;
+
+	if (port > 1)
+		return -EINVAL;
+
+	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+				 port * 4);
+
+	/* Set Power polarity */
+	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+	/* ENET1 reset */
+	MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* ENET1 interrupt */
+	MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(4, 17)
+
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	/* Reset LAN8742 PHY */
+	ret = gpio_request(ENET_PHY_RESET_GPIO, "phy-reset");
+	if (!ret)
+		gpio_direction_output(ENET_PHY_RESET_GPIO , 0);
+	mdelay(10);
+	gpio_set_value(ENET_PHY_RESET_GPIO, 1);
+	mdelay(10);
+
+	return cpu_eth_init(bis);
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	/*
+	 * Use 50M anatop loopback REF_CLK1 for ENET1,
+	 * clear gpr1[13], set gpr1[17].
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+
+	setup_fec(CONFIG_FEC_ENET_DEV);
+
+	setup_usb();
+
+	return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x60, 0x28, 0x00, 0x00)},
+	{ NULL, 0 },
+};
+
+int board_late_init(void)
+{
+	add_board_boot_modes(board_boot_modes);
+	setenv("board_name", "xpress");
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: CCV-EVA xPress\n");
+
+	return 0;
+}
diff --git a/board/freescale/mx6qarm2/imximage_mx6dl.cfg b/board/freescale/mx6qarm2/imximage_mx6dl.cfg
index ae8dcc626ed..1f5a0a57d5e 100644
--- a/board/freescale/mx6qarm2/imximage_mx6dl.cfg
+++ b/board/freescale/mx6qarm2/imximage_mx6dl.cfg
@@ -234,7 +234,7 @@ DATA 4 0x021b0018 0x0000174C
 /* MMDC0_MDRWD;*/
 DATA 4 0x021b002c 0x0f9f26d2
 /* MMDC0_MDOR */
-DATA 4 0x021b0030 0x0000020e
+DATA 4 0x021b0030 0x009f0e10
 /* MMDC0_MDCFG3LP */
 DATA 4 0x021b0038 0x00190778
 /* MMDC0_MDOTC */
@@ -263,7 +263,7 @@ DATA 4 0x021b4018 0x0000174C
 /* MMDC1_MDRWD;*/
 DATA 4 0x021b402c 0x0f9f26d2
 /* MMDC1_MDOR */
-DATA 4 0x021b4030 0x0000020e
+DATA 4 0x021b4030 0x009f0e10
 /* MMDC1_MDCFG3LP */
 DATA 4 0x021b4038 0x00190778
 /* MMDC1_MDOTC */
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index e9d9664a823..2319354fa33 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -365,34 +365,24 @@ static void do_enable_hdmi(struct display_info_t const *dev)
 	imx_enable_hdmi_phy();
 }
 
-static void enable_lvds(struct display_info_t const *dev)
-{
-	struct iomuxc *iomux = (struct iomuxc *)
-				IOMUXC_BASE_ADDR;
-	u32 reg = readl(&iomux->gpr[2]);
-	reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
-	       IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT;
-	writel(reg, &iomux->gpr[2]);
-}
-
 struct display_info_t const displays[] = {{
 	.bus	= -1,
 	.addr	= 0,
 	.pixfmt	= IPU_PIX_FMT_RGB666,
 	.detect	= NULL,
-	.enable	= enable_lvds,
+	.enable	= NULL,
 	.mode	= {
 		.name           = "Hannstar-XGA",
 		.refresh        = 60,
 		.xres           = 1024,
 		.yres           = 768,
-		.pixclock       = 15385,
-		.left_margin    = 220,
-		.right_margin   = 40,
-		.upper_margin   = 21,
-		.lower_margin   = 7,
-		.hsync_len      = 60,
-		.vsync_len      = 10,
+		.pixclock       = 15384,
+		.left_margin    = 160,
+		.right_margin   = 24,
+		.upper_margin   = 29,
+		.lower_margin   = 3,
+		.hsync_len      = 136,
+		.vsync_len      = 6,
 		.sync           = FB_SYNC_EXT,
 		.vmode          = FB_VMODE_NONINTERLACED
 } }, {
@@ -406,13 +396,13 @@ struct display_info_t const displays[] = {{
 		.refresh        = 60,
 		.xres           = 1024,
 		.yres           = 768,
-		.pixclock       = 15385,
-		.left_margin    = 220,
-		.right_margin   = 40,
-		.upper_margin   = 21,
-		.lower_margin   = 7,
-		.hsync_len      = 60,
-		.vsync_len      = 10,
+		.pixclock       = 15384,
+		.left_margin    = 160,
+		.right_margin   = 24,
+		.upper_margin   = 29,
+		.lower_margin   = 3,
+		.hsync_len      = 136,
+		.vsync_len      = 6,
 		.sync           = FB_SYNC_EXT,
 		.vmode          = FB_VMODE_NONINTERLACED
 } }, {
diff --git a/board/freescale/mx6slevk/imximage.cfg b/board/freescale/mx6slevk/imximage.cfg
index 16ea5976250..c77bbde4d8a 100644
--- a/board/freescale/mx6slevk/imximage.cfg
+++ b/board/freescale/mx6slevk/imximage.cfg
@@ -70,7 +70,7 @@ DATA 4 0x020e05d0 0x00080000
 DATA 4 0x021b001c 0x00008000
 DATA 4 0x021b085c 0x1b4700c7
 DATA 4 0x021b0800 0xa1390003
-DATA 4 0x021b0890 0x00300000
+DATA 4 0x021b0890 0x00400000
 DATA 4 0x021b08b8 0x00000800
 DATA 4 0x021b081c 0x33333333
 DATA 4 0x021b0820 0x33333333
@@ -92,7 +92,7 @@ DATA 4 0x021b0010 0x00100A82
 DATA 4 0x021b0014 0x00000093
 DATA 4 0x021b0018 0x00001688
 DATA 4 0x021b002c 0x0f9f26d2
-DATA 4 0x021b0030 0x0000020e
+DATA 4 0x021b0030 0x009f0e10
 DATA 4 0x021b0038 0x00190778
 DATA 4 0x021b0008 0x00000000
 DATA 4 0x021b0040 0x0000004f
diff --git a/board/ge/bx50v3/Kconfig b/board/ge/bx50v3/Kconfig
new file mode 100644
index 00000000000..d50dece18ee
--- /dev/null
+++ b/board/ge/bx50v3/Kconfig
@@ -0,0 +1,18 @@
+if TARGET_GE_B450V3 || TARGET_GE_B650V3 || TARGET_GE_B850V3
+
+config IMX_CONFIG
+	default "board/ge/bx50v3/bx50v3.cfg"
+
+config SYS_BOARD
+	default "bx50v3"
+
+config SYS_VENDOR
+	default "ge"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "ge_bx50v3"
+
+endif
diff --git a/board/ge/bx50v3/MAINTAINERS b/board/ge/bx50v3/MAINTAINERS
new file mode 100644
index 00000000000..8e6079197f2
--- /dev/null
+++ b/board/ge/bx50v3/MAINTAINERS
@@ -0,0 +1,8 @@
+GE_BX50V3 BOARD
+M:	Martin Donnelly <martin.donnelly@ge.com>
+S:	Maintained
+F:	board/ge/bx50v3/
+F:	include/configs/ge_bx50v3.h
+F:	configs/ge_b450v3_defconfig
+F:	configs/ge_b650v3_defconfig
+F:	configs/ge_b850v3_defconfig
diff --git a/board/ge/bx50v3/Makefile b/board/ge/bx50v3/Makefile
new file mode 100644
index 00000000000..bcd149f5b06
--- /dev/null
+++ b/board/ge/bx50v3/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2015 Timesys Corporation
+# Copyright 2015 General Electric Company
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := bx50v3.o
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
new file mode 100644
index 00000000000..70c298d2d0c
--- /dev/null
+++ b/board/ge/bx50v3/bx50v3.c
@@ -0,0 +1,533 @@
+/*
+ * Copyright 2015 Timesys Corporation
+ * Copyright 2015 General Electric Company
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |	\
+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	/* AR8033 PHY Reset */
+	MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* Reset AR8033 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 28), 1);
+}
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
+}
+
+static void setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+}
+#endif
+
+static iomux_v3_cfg_t const pcie_pads[] = {
+	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_pcie(void)
+{
+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+#define USDHC4_CD_GPIO	IMX_GPIO_NR(6, 11)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = 1; /* eMMC is always present */
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = !gpio_get_value(USDHC4_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			gpio_direction_input(USDHC4_CD_GPIO);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers\n"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+static int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	/* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
+	/* set device address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	/* offset 0x8016: CLK_25M Clock Select */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	/* enable register write, no post increment, address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+	/* set to 125 MHz from local PLL source */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
+
+	/* rgmii tx clock delay enable */
+	/* set debug port address: SerDes Test and System Mode Control */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	/* enable rgmii tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+#if defined(CONFIG_VIDEO_IPUV3)
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* Power for LVDS Display */
+	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
+	/* Backlight enable for LVDS display */
+	MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
+};
+
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+int board_cfb_skip(void)
+{
+	gpio_direction_output(LVDS_POWER_GP, 1);
+
+	return 0;
+}
+
+static int detect_baseboard(struct display_info_t const *dev)
+{
+	if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) ||
+	    IS_ENABLED(CONFIG_TARGET_GE_B650V3))
+		return 1;
+
+	return 0;
+}
+
+struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= -1,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_baseboard,
+	.enable	= NULL,
+	.mode	= {
+		.name           = "G121X1-L03",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 20,
+		.right_margin   = 300,
+		.upper_margin   = 30,
+		.lower_margin   = 8,
+		.hsync_len      = 1,
+		.vsync_len      = 1,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	.bus	= -1,
+	.addr	= 3,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	reg = readl(&mxc_ccm->CCGR3);
+	reg |=  MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+
+	reg = readl(&mxc_ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
+		 MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
+	       (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	reg = readl(&mxc_ccm->cscmr2);
+	reg |= (MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+	writel(reg, &mxc_ccm->cscmr2);
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	     | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	     | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+	     | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT
+	     | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	     | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0
+	     | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
+		       IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
+		       IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	/* backlights off until needed */
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+	gpio_direction_input(LVDS_POWER_GP);
+	gpio_direction_input(LVDS_BACKLIGHT_GP);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	setup_pcie();
+
+	return cpu_eth_init(bis);
+}
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	MX6_PAD_KEY_ROW2__GPIO4_IO11	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+#define SUS_S3_OUT	IMX_GPIO_NR(4, 11)
+#define WIFI_EN	IMX_GPIO_NR(6, 14)
+
+int board_early_init_f(void)
+{
+	imx_iomux_v3_setup_multiple_pads(misc_pads,
+					 ARRAY_SIZE(misc_pads));
+
+	setup_iomux_uart();
+
+
+	return 0;
+}
+
+int board_init(void)
+{
+	gpio_direction_output(SUS_S3_OUT, 1);
+	gpio_direction_output(WIFI_EN, 1);
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+	/* We need at least 200ms between power on and backlight on
+	 * as per specifications from CHI MEI */
+	mdelay(250);
+
+	/* Backlight Power */
+	gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	printf("BOARD: %s\n", CONFIG_BOARD_NAME);
+	return 0;
+}
diff --git a/board/ge/bx50v3/bx50v3.cfg b/board/ge/bx50v3/bx50v3.cfg
new file mode 100644
index 00000000000..de88769067a
--- /dev/null
+++ b/board/ge/bx50v3/bx50v3.cfg
@@ -0,0 +1,151 @@
+/*
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+/* DDR IO */
+DATA 4, MX6_IOM_GRP_DDR_TYPE,	0x000c0000
+DATA 4, MX6_IOM_GRP_DDRPKE,	0x00000000
+DATA 4, MX6_IOM_DRAM_SDCLK_0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1,	0x00000030
+DATA 4, MX6_IOM_DRAM_CAS,	0x00000030
+DATA 4, MX6_IOM_DRAM_RAS,	0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS,	0x00000030
+DATA 4, MX6_IOM_DRAM_RESET,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2,	0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1,	0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS,	0x00000030
+DATA 4, MX6_IOM_DDRMODE_CTL,	0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS1,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS2,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS3,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS4,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS5,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS6,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS7,	0x00000030
+DATA 4, MX6_IOM_GRP_DDRMODE,	0x00020000
+DATA 4, MX6_IOM_GRP_B0DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B1DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B2DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B3DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B4DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B5DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B6DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B7DS,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM0,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM1,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM2,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM3,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM4,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM5,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM6,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM7,	0x00000030
+
+/* Calibrations */
+/* ZQ */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL,  0xa1390003
+/* write leveling */
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/* Read DQS Gating calibration */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0,	0x45380544
+DATA 4, MX6_MMDC_P0_MPDGCTRL1,	0x05280530
+DATA 4, MX6_MMDC_P1_MPDGCTRL0,	0x4530053C
+DATA 4, MX6_MMDC_P1_MPDGCTRL1,	0x0530050C
+/* Read calibration */
+DATA 4, MX6_MMDC_P0_MPRDDLCTL,	0x36303032
+DATA 4, MX6_MMDC_P1_MPRDDLCTL,	0x38363042
+/* Write calibration */
+DATA 4, MX6_MMDC_P0_MPWRDLCTL,	0x3A3A423E
+DATA 4, MX6_MMDC_P1_MPWRDLCTL,	0x4A38483E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0,	0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0,	0x00000800
+
+/* MMDC init */
+DATA 4, MX6_MMDC_P0_MDPDC,	0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC,	0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0,	0x8A8F79A4
+DATA 4, MX6_MMDC_P0_MDCFG1,	0xDB538E64
+DATA 4, MX6_MMDC_P0_MDCFG2,	0x01ff00db
+DATA 4, MX6_MMDC_P0_MDMISC,	0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD,	0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR,	0x008F1023
+DATA 4, MX6_MMDC_P0_MDASP,	0x00000047
+DATA 4, MX6_MMDC_P0_MDCTL,	0x841a0000
+
+/* Initialize Micron MT41J128M */
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04088032
+DATA 4, MX6_MMDC_P0_MDSCR,	0x0408803a
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR,	0x0000803b
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408031
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408039
+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408030
+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408038
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008040
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008048
+DATA 4, MX6_MMDC_P0_MDREF,	0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL,	0x00011117
+DATA 4, MX6_MMDC_P1_MPODTCTRL,	0x00011117
+DATA 4, MX6_MMDC_P0_MDPDC,	0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR,	0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00000000
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0x00FFF300
+DATA 4, CCM_CCGR5, 0x0F0000C3
+DATA 4, CCM_CCGR6, 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  1	   --> CKO1 enabled
+ * cko1_div 111  --> divide by 8
+ * cko1_sel 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 132/8 16.5 MHz
+ */
+DATA 4, CCM_CCOSR, 0x000000fb
diff --git a/board/warp7/Kconfig b/board/warp7/Kconfig
new file mode 100644
index 00000000000..61c33fb53e1
--- /dev/null
+++ b/board/warp7/Kconfig
@@ -0,0 +1,9 @@
+if TARGET_WARP7
+
+config SYS_BOARD
+	default "warp7"
+
+config SYS_CONFIG_NAME
+	default "warp7"
+
+endif
diff --git a/board/warp7/MAINTAINERS b/board/warp7/MAINTAINERS
new file mode 100644
index 00000000000..1d3ee292222
--- /dev/null
+++ b/board/warp7/MAINTAINERS
@@ -0,0 +1,6 @@
+WARP7 BOARD
+M:	Fabio Estevam <fabio.estevam@nxp.com>
+S:	Maintained
+F:	board/warp7/
+F:	include/configs/warp7.h
+F:	configs/warp7_defconfig
diff --git a/board/warp7/Makefile b/board/warp7/Makefile
new file mode 100644
index 00000000000..f39d1d8f120
--- /dev/null
+++ b/board/warp7/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2016 NXP Semiconductors
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := warp7.o
diff --git a/board/warp7/imximage.cfg b/board/warp7/imximage.cfg
new file mode 100644
index 00000000000..e7b6d30d379
--- /dev/null
+++ b/board/warp7/imximage.cfg
@@ -0,0 +1,95 @@
+/*
+ * Copyright (C) 2016 NXP Semiconductors
+ *
+ * SPDX-License-Identifier:	GPL-2.0
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+IMAGE_VERSION	2
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x03040008
+DATA 4 0x307a0064 0x00200038
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00350001
+DATA 4 0x307a00dc 0x00c3000a
+DATA 4 0x307a00e0 0x00010000
+DATA 4 0x307a00e4 0x00110006
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x0a0e110b
+DATA 4 0x307a0104 0x00020211
+DATA 4 0x307a0108 0x03060708
+DATA 4 0x307a010c 0x00a0500c
+DATA 4 0x307a0110 0x05020307
+DATA 4 0x307a0114 0x02020404
+DATA 4 0x307a0118 0x02020003
+DATA 4 0x307a011c 0x00000202
+DATA 4 0x307a0120 0x00000202
+
+DATA 4 0x307a0180 0x00600018
+DATA 4 0x307a0184 0x00e00100
+DATA 4 0x307a0190 0x02098205
+DATA 4 0x307a0194 0x00060303
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+
+DATA 4 0x307a0200 0x00000015
+DATA 4 0x307a0204 0x00161616
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x04040404
+DATA 4 0x307a0218 0x0f0f0404
+
+DATA 4 0x307a0240 0x06000600
+DATA 4 0x307a0244 0x00000000
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17421e40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790008 0x00010000
+DATA 4 0x30790010 0x0007080c
+DATA 4 0x307900b0 0x1010007e
+
+DATA 4 0x3079001C 0x01010000
+DATA 4 0x3079009c 0x00000d6e
+
+DATA 4 0x30790030 0x06060606
+DATA 4 0x30790020 0x0a0a0a0a
+DATA 4 0x30790050 0x01000008
+DATA 4 0x30790050 0x00000008
+DATA 4 0x30790018 0x0000000f
+DATA 4 0x307900c0 0x0e487304
+DATA 4 0x307900c0 0x0e4c7304
+DATA 4 0x307900c0 0x0e4c7306
+DATA 4 0x307900c0 0x0e4c7304
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e487304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+
+CHECK_BITS_SET 4 0x307a0004 0x1
diff --git a/board/warp7/warp7.c b/board/warp7/warp7.c
new file mode 100644
index 00000000000..8c5bf9a5242
--- /dev/null
+++ b/board/warp7/warp7.c
@@ -0,0 +1,102 @@
+/*
+ * Copyright (C) 2016 NXP Semiconductors
+ * Author: Fabio Estevam <fabio.estevam@nxp.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/crm_regs.h>
+#include <usb.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \
+			PAD_CTL_HYS)
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW |	\
+			PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__SD3_RESET_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+		/* Assume uSDHC3 emmc is always present */
+		return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: WARP7\n");
+
+	return 0;
+}
+
+int board_usb_phy_mode(int port)
+{
+	return USB_INIT_DEVICE;
+}
diff --git a/configs/ge_b450v3_defconfig b/configs/ge_b450v3_defconfig
new file mode 100644
index 00000000000..02873ce59ce
--- /dev/null
+++ b/configs/ge_b450v3_defconfig
@@ -0,0 +1,8 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_GE_B450V3=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/ge_b650v3_defconfig b/configs/ge_b650v3_defconfig
new file mode 100644
index 00000000000..3d10b350940
--- /dev/null
+++ b/configs/ge_b650v3_defconfig
@@ -0,0 +1,8 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_GE_B650V3=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/ge_b850v3_defconfig b/configs/ge_b850v3_defconfig
new file mode 100644
index 00000000000..e3f4a0a8475
--- /dev/null
+++ b/configs/ge_b850v3_defconfig
@@ -0,0 +1,8 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_GE_B850V3=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/mx28evk_defconfig b/configs/mx28evk_defconfig
index d0e413ddd36..bb900ff72da 100644
--- a/configs/mx28evk_defconfig
+++ b/configs/mx28evk_defconfig
@@ -1,6 +1,7 @@
 CONFIG_ARM=y
 CONFIG_TARGET_MX28EVK=y
 CONFIG_SPL=y
+CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="ENV_IS_IN_MMC"
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
diff --git a/configs/mx6sxsabreauto_defconfig b/configs/mx6sxsabreauto_defconfig
index d9e35dfc91c..631a99868ac 100644
--- a/configs/mx6sxsabreauto_defconfig
+++ b/configs/mx6sxsabreauto_defconfig
@@ -1,7 +1,7 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MX6=y
 CONFIG_TARGET_MX6SXSABREAUTO=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg"
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
diff --git a/configs/mx6sxsabresd_defconfig b/configs/mx6sxsabresd_defconfig
index f4e88f27fb3..2ea5c893856 100644
--- a/configs/mx6sxsabresd_defconfig
+++ b/configs/mx6sxsabresd_defconfig
@@ -1,7 +1,7 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MX6=y
 CONFIG_TARGET_MX6SXSABRESD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg,MX6SX"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg"
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
diff --git a/configs/mx6sxsabresd_spl_defconfig b/configs/mx6sxsabresd_spl_defconfig
index 2713a4b5931..548adf6328c 100644
--- a/configs/mx6sxsabresd_spl_defconfig
+++ b/configs/mx6sxsabresd_spl_defconfig
@@ -2,7 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_MX6=y
 CONFIG_TARGET_MX6SXSABRESD=y
 CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6SX"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg"
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
diff --git a/configs/mx7dsabresd_defconfig b/configs/mx7dsabresd_defconfig
index 08d19f9b4b5..137369c0de2 100644
--- a/configs/mx7dsabresd_defconfig
+++ b/configs/mx7dsabresd_defconfig
@@ -3,7 +3,7 @@ CONFIG_ARCH_MX7=y
 CONFIG_TARGET_MX7DSABRESD=y
 CONFIG_IMX_RDC=y
 CONFIG_IMX_BOOTAUX=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg,MX7D"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg"
 # CONFIG_CMD_BOOTD is not set
 # CONFIG_CMD_IMI is not set
 # CONFIG_CMD_IMLS is not set
diff --git a/configs/warp7_defconfig b/configs/warp7_defconfig
new file mode 100644
index 00000000000..f37c9f53cd4
--- /dev/null
+++ b/configs/warp7_defconfig
@@ -0,0 +1,12 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_TARGET_WARP7=y
+CONFIG_IMX_RDC=y
+CONFIG_IMX_BOOTAUX=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/warp7/imximage.cfg"
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
diff --git a/configs/xpress_defconfig b/configs/xpress_defconfig
new file mode 100644
index 00000000000..033d32b6156
--- /dev/null
+++ b/configs/xpress_defconfig
@@ -0,0 +1,6 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ccv/xpress/imximage.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
diff --git a/configs/xpress_spl_defconfig b/configs/xpress_spl_defconfig
new file mode 100644
index 00000000000..c2b10756b4b
--- /dev/null
+++ b/configs/xpress_spl_defconfig
@@ -0,0 +1,7 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
new file mode 100644
index 00000000000..6fa4a9a0e4d
--- /dev/null
+++ b/include/configs/ge_bx50v3.h
@@ -0,0 +1,349 @@
+/*
+ * Copyright (C) 2015 Timesys Corporation
+ * Copyright (C) 2015 General Electric Company
+ * Copyright (C) 2014 Advantech
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the GE MX6Q Bx50v3 boards.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __GE_BX50V3_CONFIG_H
+#define __GE_BX50V3_CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#if defined(CONFIG_TARGET_GE_B450V3)
+#define CONFIG_BOARD_NAME	"General Electric B450v3"
+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b450v3.dtb"
+#elif defined(CONFIG_TARGET_GE_B650V3)
+#define CONFIG_BOARD_NAME	"General Electric B650v3"
+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b650v3.dtb"
+#elif defined(CONFIG_TARGET_GE_B850V3)
+#define CONFIG_BOARD_NAME	"General Electric B850v3"
+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b850v3.dtb"
+#else
+#define CONFIG_BOARD_NAME	"General Electric BA16 Generic"
+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-ba16.dtb"
+#endif
+
+#define CONFIG_MXC_UART_BASE	UART3_BASE
+#define CONFIG_CONSOLE_DEV	"ttymxc2"
+
+#define PHYS_SDRAM_SIZE		(2u * 1024 * 1024 * 1024)
+
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+#define CONFIG_BOOTDELAY               1
+
+#include "mx6_common.h"
+#include <linux/sizes.h>
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_GPIO
+#define CONFIG_MXC_UART
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+
+/* SATA Configs */
+#define CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
+
+#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+#define CONFIG_G_DNL_VENDOR_NUM   0x0525
+#define CONFIG_G_DNL_PRODUCT_NUM  0xa4a5
+#define CONFIG_G_DNL_MANUFACTURER "Advantech"
+
+/* Networking Configs */
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME		"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		4
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* Serial Flash */
+#define CONFIG_CMD_SF
+#ifdef CONFIG_CMD_SF
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		0
+#define CONFIG_SF_DEFAULT_SPEED	20000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#endif
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_BAUDRATE	115200
+
+/* Command definition */
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_BOOTZ
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_LOADADDR	0x12000000
+#define CONFIG_SYS_TEXT_BASE	0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=/boot/uImage\0" \
+	"uboot=u-boot.imx\0" \
+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"fdt_addr=0x18000000\0" \
+	"boot_fdt=yes\0" \
+	"ip_dyn=yes\0" \
+	"console=" CONFIG_CONSOLE_DEV "\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"initrd_high=0xffffffff\0" \
+	"sddev=0\0" \
+	"emmcdev=1\0" \
+	"partnum=1\0" \
+	"update_sd_firmware=" \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"if mmc dev ${mmcdev}; then "	\
+			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
+				"setexpr fw_sz ${filesize} / 0x200; " \
+				"setexpr fw_sz ${fw_sz} + 1; "	\
+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+			"fi; "	\
+		"fi\0" \
+	"update_sf_uboot=" \
+		"if tftp $loadaddr $uboot; then " \
+			"sf probe; " \
+			"sf erase 0 0xC0000; " \
+			"sf write $loadaddr 0x400 $filesize; " \
+			"echo 'U-Boot upgraded. Please reset'; " \
+		"fi\0" \
+	"setargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/${rootdev} rw rootwait cma=128M\0" \
+	"loadbootscript=" \
+		"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
+		" source\0" \
+	"loadimage=" \
+		"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
+	"loadfdt=ext2load ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
+	"tryboot=" \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loadimage; then " \
+				"run doboot; " \
+			"fi; " \
+		"fi;\0" \
+	"doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+		"run setargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootm ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootm; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootm; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootm ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootm; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootm; " \
+		"fi;\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"usb start; " \
+	"setenv dev usb; " \
+	"setenv devnum 0; " \
+	"setenv rootdev sda1; " \
+	"run tryboot; " \
+	\
+	"setenv dev mmc; " \
+	"setenv rootdev mmcblk0p1; " \
+	\
+	"setenv devnum ${sddev}; " \
+	"if mmc dev ${devnum}; then " \
+		"run tryboot; " \
+		"setenv rootdev mmcblk1p1; " \
+	"fi; " \
+	\
+	"setenv devnum ${emmcdev}; " \
+	"if mmc dev ${devnum}; then " \
+		"run tryboot; " \
+	"fi; " \
+	\
+	"bmode usb; " \
+
+#define CONFIG_ARP_TIMEOUT     200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
+#define CONFIG_AUTO_COMPLETE
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START       0x10000000
+#define CONFIG_SYS_MEMTEST_END         0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE               (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE		(8 * 1024)
+#define CONFIG_ENV_OFFSET		(768 * 1024)
+#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+
+#define CONFIG_OF_LIBFDT
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+
+#undef CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(7, 12)
+#define CONFIG_PCIE_IMX_POWER_GPIO	IMX_GPIO_NR(1, 5)
+#endif
+
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED		  100000
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+
+#endif	/* __GE_BX50V3_CONFIG_H */
diff --git a/include/configs/m53evk.h b/include/configs/m53evk.h
index 1efe48c7f81..dc857680241 100644
--- a/include/configs/m53evk.h
+++ b/include/configs/m53evk.h
@@ -41,6 +41,7 @@
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SATA
 #define CONFIG_CMD_USB
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
index a52c8c90710..4d86c134caf 100644
--- a/include/configs/mx28evk.h
+++ b/include/configs/mx28evk.h
@@ -23,7 +23,10 @@
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
 #define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_PING
diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h
index ceea74ed73b..3e1b760882e 100644
--- a/include/configs/mx6sabre_common.h
+++ b/include/configs/mx6sabre_common.h
@@ -209,7 +209,7 @@
 #define CONFIG_ENV_IS_IN_MMC
 
 #if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_ENV_OFFSET		(8 * 64 * 1024)
+#define CONFIG_ENV_OFFSET		(768 * 1024)
 #endif
 
 /* Framebuffer */
diff --git a/include/configs/mx7_common.h b/include/configs/mx7_common.h
index a627456d93f..9bd61145d89 100644
--- a/include/configs/mx7_common.h
+++ b/include/configs/mx7_common.h
@@ -27,19 +27,10 @@
 
 /* Enable iomux-lpsr support */
 #define CONFIG_IOMUX_LPSR
-#define CONFIG_IMX_FIXED_IVT_OFFSET
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN           (32 * SZ_1M)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
 
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
-#define CONFIG_FSL_CLK
-
 #define CONFIG_LOADADDR                 0x80800000
 #define CONFIG_SYS_TEXT_BASE            0x87800000
 
@@ -79,7 +70,6 @@
 
 /* UART */
 #define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR
 
 /* MMC */
 #define CONFIG_MMC
diff --git a/include/configs/mx7dsabresd.h b/include/configs/mx7dsabresd.h
index 5d897c253f8..da1d26f3509 100644
--- a/include/configs/mx7dsabresd.h
+++ b/include/configs/mx7dsabresd.h
@@ -14,6 +14,14 @@
 #define CONFIG_DBG_MONITOR
 #define PHYS_SDRAM_SIZE			SZ_1G
 
+#define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
 /* Uncomment to enable secure boot support */
 /* #define CONFIG_SECURE_BOOT */
 #define CONFIG_CSF_SIZE			0x4000
diff --git a/include/configs/warp7.h b/include/configs/warp7.h
new file mode 100644
index 00000000000..d1404b2555b
--- /dev/null
+++ b/include/configs/warp7.h
@@ -0,0 +1,155 @@
+/*
+ * Copyright (C) 2016 NXP Semiconductors
+ *
+ * Configuration settings for the i.MX7S Warp board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __WARP7_CONFIG_H
+#define __WARP7_CONFIG_H
+
+#define CONFIG_BOOTDELAY                1
+#include "mx7_common.h"
+
+#define PHYS_SDRAM_SIZE			SZ_512M
+
+#define CONFIG_MXC_UART_BASE		UART1_IPS_BASE_ADDR
+
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* MMC Config*/
+#define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC3_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+#define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_DFU_ENV_SETTINGS \
+	"dfu_alt_info=image raw 0 0x800000;"\
+		"u-boot raw 0 0x4000;"\
+		"bootimg part 0 1;"\
+		"rootfs part 0 2\0" \
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_DFU_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=imx7d-warp.dtb\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev};" \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "fi"
+
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_IS_IN_MMC
+
+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#define CONFIG_SYS_FSL_USDHC_NUM	1
+
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		0
+#define CONFIG_MMCROOT			"/dev/mmcblk2p2"
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX7
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Only OTG1 port enabled */
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET_DUALSPEED
+
+#define CONFIG_USB_GADGET
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+#define CONFIG_USB_GADGET_DOWNLOAD
+#define CONFIG_USB_GADGET_VBUS_DRAW	2
+
+#define CONFIG_G_DNL_VENDOR_NUM		0x0525
+#define CONFIG_G_DNL_PRODUCT_NUM	0xa4a5
+#define CONFIG_G_DNL_MANUFACTURER	"FSL"
+
+/* USB Device Firmware Update support */
+#define CONFIG_CMD_DFU
+#define CONFIG_USB_FUNCTION_DFU
+#define CONFIG_DFU_MMC
+#define CONFIG_SYS_DFU_DATA_BUF_SIZE	SZ_16M
+#define DFU_DEFAULT_POLL_TIMEOUT	300
+
+#endif
diff --git a/include/configs/xpress.h b/include/configs/xpress.h
new file mode 100644
index 00000000000..9bc536bdbbe
--- /dev/null
+++ b/include/configs/xpress.h
@@ -0,0 +1,166 @@
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * Configuration settings for the CCV xPress board
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __XPRESS_CONFIG_H
+#define __XPRESS_CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/imx-common/gpio.h>
+
+/* SPL options */
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#include "imx6_spl.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 << 20)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+
+/* I2C configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* Miscellaneous configurable options */
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			(128 << 20)
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+/* Environment is in stored in the eMMC boot partition */
+#define CONFIG_ENV_SIZE			(16 << 10)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET		(512 << 10)
+#define CONFIG_SYS_MMC_ENV_DEV		0	/* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_PART		1	/* boot parition */
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC2 */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_CACHE
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_FEC_ENET_DEV		0
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR          0x0
+#define CONFIG_FEC_XCV_TYPE             RMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_UBOOT_SECTOR_START	0x2
+#define CONFIG_UBOOT_SECTOR_COUNT	0x3fe
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc0\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=undefined\0" \
+	"fdt_addr=0x83000000\0" \
+	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"bootz ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootz; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi; " \
+			"fi; " \
+		"else " \
+			"bootz; " \
+		"fi;\0" \
+	"uboot=ccv/u-boot.imx\0"					\
+	"uboot_start="__stringify(CONFIG_UBOOT_SECTOR_START)"\0"	\
+	"uboot_size="__stringify(CONFIG_UBOOT_SECTOR_COUNT)"\0"		\
+	"update_uboot=if tftp ${uboot}; then "				\
+		"if itest ${filesize} > 0; then "			\
+			"mmc dev 0 1;"					\
+			"setexpr blkc ${filesize} / 0x200;"		\
+			"setexpr blkc ${blkc} + 1;"			\
+			"if itest ${blkc} <= ${uboot_size}; then "	\
+				"mmc write ${loadaddr} ${uboot_start} "	\
+					"${blkc};"			\
+			"fi;"						\
+		"fi; fi;"						\
+		"setenv filesize; setenv blkc\0"			\
+	"update_bootpart=mmc bootbus 0 2 1 2;mmc partconf 0 1 1 0\0"
+
+#endif /* __XPRESS_CONFIG_H */