Initial revision

1 files changed, 354 insertions, 0 deletions

diff --git a/include/configs/GENIETV.h b/include/configs/GENIETV.h
new file mode 100644
index 00000000000..99e2cfcb705
--- /dev/null
+++ b/include/configs/GENIETV.h
@@ -0,0 +1,354 @@
+ /*
+  * A collection of structures, addresses, and values associated with
+  * the Motorola 860T FADS board.  Copied from the MBX stuff.
+  * Magnus Damm added defines for 8xxrom and extended bd_info.
+  * Helmut Buchsbaum added bitvalues for BCSRx
+  *
+  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+  */
+
+/*
+ * The GENIETV is using the following physical memorymap (copied from
+ * the FADS configuration):
+ *
+ * ff020000 -> ff02ffff : pcmcia
+ * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by 8xxROM
+ * ff000000 -> ff00ffff : IMAP       internal in the cpu
+ * 30000000 -> 300fffff : flash      connected to CS0
+ * 00000000 -> nnnnnnnn : sdram      setup by U-Boot
+ *
+ * CS pins are connected as follows:
+ *
+ * CS0 -512Kb boot flash
+ * CS1 - SDRAM #1
+ * CS2 - SDRAM #2
+ * CS3 - Flash #1
+ * CS4 - Flash #2
+ * CS5 - Lon (if present)
+ * CS6 - PCMCIA #1
+ * CS7 - PCMCIA #2
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define	CONFIG_ETHADDR		08:00:22:50:70:63	/* Ethernet address */
+#define CONFIG_ENV_OVERWRITE	1	/* Overwrite the environment */
+
+#define CFG_ALLOC_DPRAM			/* Use dynamic DPRAM allocation */
+
+#define CFG_AUTOLOAD		"n"	/* No autoload */
+
+/*#define CONFIG_VIDEO		1	/  To enable the video initialization */
+/*#define CONFIG_VIDEO_ADDR	0x00200000 */
+/*#define CONFIG_HARD_I2C	1	/  I2C with hardware support */
+/*#define CONFIG_PCMCIA		1	/  To enable the PCMCIA initialization */
+
+/*#define CFG_PCMCIA_IO_ADDR	0xff020000 */
+/*#define CFG_PCMCIA_IO_SIZE	0x10000 */
+/*#define CFG_PCMCIA_MEM_ADDR	0xe0000000 */
+/*#define CFG_PCMCIA_MEM_SIZE	0x10000 */
+
+/* Video related */
+
+/*#define CONFIG_VIDEO_LOGO			1	/  Show the logo */
+/*#define CONFIG_VIDEO_ENCODER_AD7177		1	/  Enable this encoder */
+/*#define CONFIG_VIDEO_ENCODER_AD7177_ADDR	0xF4	/  ALSB to ground */
+
+/* Wireless 56Khz 4PPM keyboard on SMCx */
+
+/*#define CONFIG_WL_4PPM_KEYBOARD		0 */
+/*#define CONFIG_WL_4PPM_KEYBOARD_SMC	0	/  SMC to use (0 indexed) */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#include <mpc8xx_irq.h>
+
+#define CONFIG_GENIETV		1
+#define CONFIG_MPC823		1
+
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#undef	CONFIG_8xx_CONS_SMC2
+#undef	CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE		9600
+
+#define MPC8XX_FACT	12 			/* Multiply by 12	*/
+#define MPC8XX_XIN	5000000			/* 4 MHz clock 		*/
+
+#define MPC8XX_HZ 	((MPC8XX_XIN) * (MPC8XX_FACT))
+#define CFG_PLPRCR_MF	((MPC8XX_FACT-1) << 20)
+#define CONFIG_8xx_GCLK_FREQ	MPC8XX_HZ	/* Force it - dont measure it */
+
+#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#if 1
+#define CONFIG_BOOTDELAY	1	/* autoboot after 2 seconds	*/
+#define CONFIG_LOADS_ECHO	0	/* Dont echoes received characters */
+#define CONFIG_BOOTARGS		""
+#define CONFIG_BOOTCOMMAND							\
+"bootp; tftp; "									\
+"setenv bootargs console=tty0 console=ttyS0 " 					\
+"root=/dev/nfs nfsroot=$(serverip):$(rootpath) " 				\
+"ip=$(ipaddr):$(serverip):$(gatewayip):$(subnetmask):$(hostname):eth0:off ;" 	\
+"bootm "
+#else
+#define CONFIG_BOOTDELAY	0	/* autoboot disabled		*/
+#endif
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_PROMPT		":>"		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS		8		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x00004000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x00800000	/* 0 ... 8 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x00100000	/* default load address */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 4800, 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xFF000000
+#define CFG_IMMR_SIZE		((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
+ */
+#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0x02800000
+#define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
+#if 0
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 128 kB for Monitor	*/
+#else
+#define	CFG_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
+#endif
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define	CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x10000	/* Offset of Environment Sector 	*/
+#define	CFG_ENV_SIZE		0x10000	/* Total Size of Environment Sector (64k)*/
+
+/* values according to the manual */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control					11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration						11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ *
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+ */
+#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC10)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control					11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer  *
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ *
+ * #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+ */
+#define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CFG_PLPRCR_MF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CFG_SCCR       (SCCR_TBS     | \
+				SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+				SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+				SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER		0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently.  Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register.  For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0(FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0x02800000	/* FLASH bank #0		*/
+
+#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask 	*/
+#define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask (512Kb) */
+
+/* FLASH timing */
+#define CFG_OR_TIMING_FLASH 	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
+				OR_SCY_15_CLK | OR_TRLX )
+
+/*#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH) */
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) 		/* 0xfff80ff4 */
+#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8)	/* 0x02800401 */
+
+/*
+ * BR1/2 and OR1/2 (SDRAM)
+*/
+
+#define CFG_OR_TIMING_SDRAM	0x00000A00
+
+#define SDRAM_MAX_SIZE		0x04000000	/* 64Mb bank */
+#define SDRAM_BASE1_PRELIM	0x00000000	/* First bank */
+#define SDRAM_BASE2_PRELIM	0x10000000	/* Second bank */
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MBMR_PTB		0x5d		/* start with divider for 100 MHz	*/
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
+#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
+#define CFG_MPTPR_1BK_4K        MPTPR_PTP_DIV32
+/*
+ * MBMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MBMR_8COL	((CFG_MBMR_PTB << MAMR_PTA_SHIFT)  | MAMR_PTAE | \
+			MAMR_G0CLA_A11 | MAMR_RLFA_1X | MAMR_WLFA_1X \
+			| MAMR_TLFA_4X)	/* 0x5d802114 */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define	BOOTFLAG_COLD			0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM			0x02		/* Software reboot			*/
+
+/* values according to the manual */
+
+#define CONFIG_DRAM_50MHZ		1
+#define CONFIG_SDRAM_50MHZ
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS	0
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_fads)
+
+/*
+ * MPC8xx CPM Options
+ */
+#define CONFIG_SCC_ENET 1
+
+#define CONFIG_DISK_SPINUP_TIME 1000000
+
+/* PCMCIA configuration */
+
+#define PCMCIA_MAX_SLOTS    1
+#define PCMCIA_SLOT_B 1
+
+#endif	/* __CONFIG_H */