* Add support for 16 MB flash configuration of TRAB boardLABEL_2003_02_28_0150

* Patch by Erwin Rol, 27 Feb 2003:
  Add support for RTEMS

* Add image information to README

* Fix dual PCMCIA slot support (when running with just one
  slot populated)

* Add VFD type detection to trab board

* extend drivers/cs8900.c driver to synchronize  ethaddr  environment
  variable with value in the EEPROM

* Start adding MIPS support files

1 files changed, 61 insertions, 61 deletions

diff --git a/board/sc520_cdp/sc520_cdp.c b/board/sc520_cdp/sc520_cdp.c
index ba6255f4eb6..2809ff72af1 100644
--- a/board/sc520_cdp/sc520_cdp.c
+++ b/board/sc520_cdp/sc520_cdp.c
@@ -31,35 +31,35 @@
 
 static void irq_init(void)
 {
-
+	
 	/* disable global interrupt mode */
-	write_mmcr_byte(SC520_PICICR, 0x40);
-
+	write_mmcr_byte(SC520_PICICR, 0x40); 
+	
 	/* set irq0-7 to edge */
 	write_mmcr_byte(SC520_MPICMODE, 0x00);
-
+	
 	/* set irq9-12 to level, all the other (8, 13-15) are edge */
 	write_mmcr_byte(SC520_SL1PICMODE, 0x1e);
-
+	
 	/* set irq16-24 (unused slave pic2) to level */
 	write_mmcr_byte(SC520_SL2PICMODE, 0xff);
-
-	/* active low polarity on PIC interrupt pins,
+	
+	/* active low polarity on PIC interrupt pins, 
 	   active high polarity on all other irq pins */
 	write_mmcr_word(SC520_INTPINPOL, 0);
 
 	/* set irq number mapping */
-	write_mmcr_byte(SC520_GPTMR0MAP,0);            /* disable GP timer 0 INT */
+	write_mmcr_byte(SC520_GPTMR0MAP,0);            /* disable GP timer 0 INT */       
 	write_mmcr_byte(SC520_GPTMR1MAP,0);            /* disable GP timer 1 INT */
 	write_mmcr_byte(SC520_GPTMR2MAP,0);            /* disable GP timer 2 INT */
-	write_mmcr_byte(SC520_PIT0MAP,0x1);            /* Set PIT timer 0 INT to IRQ0 */
+	write_mmcr_byte(SC520_PIT0MAP,0x1);            /* Set PIT timer 0 INT to IRQ0 */ 
 	write_mmcr_byte(SC520_PIT1MAP,0);              /* diable PIT timer 1 INT */
 	write_mmcr_byte(SC520_PIT2MAP,0);              /* diable PIT timer 2 INT */
 	write_mmcr_byte(SC520_PCIINTAMAP,0x4);         /* Set PCI INT A to IRQ9 */
 	write_mmcr_byte(SC520_PCIINTBMAP,0x5);         /* Set PCI INT B to IRQ10 */
 	write_mmcr_byte(SC520_PCIINTCMAP,0x6);         /* Set PCI INT C to IRQ11 */
 	write_mmcr_byte(SC520_PCIINTDMAP,0x7);         /* Set PCI INT D to IRQ12 */
-	write_mmcr_byte(SC520_DMABCINTMAP,0);          /* disable DMA INT */
+	write_mmcr_byte(SC520_DMABCINTMAP,0);          /* disable DMA INT */ 
 	write_mmcr_byte(SC520_SSIMAP,0);               /* disable Synchronius serial INT */
 	write_mmcr_byte(SC520_WDTMAP,0);               /* disable Watchdor INT */
 	write_mmcr_byte(SC520_RTCMAP,0x3);             /* Set RTC int to 8 */
@@ -69,28 +69,28 @@ static void irq_init(void)
 	write_mmcr_byte(SC520_GP0IMAP,6);              /* Set GPIRQ0 (ISA IRQ2) to IRQ9 */
 	write_mmcr_byte(SC520_GP1IMAP,2);              /* Set GPIRQ1 (SIO IRQ1) to IRQ1 */
 	write_mmcr_byte(SC520_GP2IMAP,7);              /* Set GPIRQ2 (ISA IRQ12) to IRQ12 */
-
+	
 	if (CFG_USE_SIO_UART) {
 		write_mmcr_byte(SC520_UART1MAP,0);     /* disable internal UART1 INT */
 		write_mmcr_byte(SC520_UART2MAP,0);     /* disable internal UART2 INT */
-		write_mmcr_byte(SC520_GP3IMAP,11);     /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
+		write_mmcr_byte(SC520_GP3IMAP,11);     /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */ 
 		write_mmcr_byte(SC520_GP4IMAP,12);     /* Set GPIRQ4 (ISA IRQ4) to IRQ4 */
 	} else {
 		write_mmcr_byte(SC520_UART1MAP,12);    /* Set internal UART2 INT to IRQ4 */
 		write_mmcr_byte(SC520_UART2MAP,11);    /* Set internal UART2 INT to IRQ3 */
-		write_mmcr_byte(SC520_GP3IMAP,0);      /* disable GPIRQ3 (ISA IRQ3) */
+		write_mmcr_byte(SC520_GP3IMAP,0);      /* disable GPIRQ3 (ISA IRQ3) */ 
 		write_mmcr_byte(SC520_GP4IMAP,0);      /* disable GPIRQ4 (ISA IRQ4) */
 	}
-
+	
 	write_mmcr_byte(SC520_GP5IMAP,13);             /* Set GPIRQ5 (ISA IRQ5) to IRQ5 */
 	write_mmcr_byte(SC520_GP6IMAP,21);             /* Set GPIRQ6 (ISA IRQ6) to IRQ6 */
 	write_mmcr_byte(SC520_GP7IMAP,22);             /* Set GPIRQ7 (ISA IRQ7) to IRQ7 */
 	write_mmcr_byte(SC520_GP8IMAP,3);              /* Set GPIRQ8 (SIO IRQ8) to IRQ8 */
 	write_mmcr_byte(SC520_GP9IMAP,4);              /* Set GPIRQ9 (ISA IRQ9) to IRQ9 */
-	write_mmcr_byte(SC520_GP10IMAP,9);             /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */
+	write_mmcr_byte(SC520_GP10IMAP,9);             /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */          
 	write_mmcr_word(SC520_PCIHOSTMAP,0x11f);       /* Map PCI hostbridge INT to NMI */
 	write_mmcr_word(SC520_ECCMAP,0x100);           /* Map SDRAM ECC failure INT to NMI */
-
+ 
 }
 
 /* PCI stuff */
@@ -98,11 +98,11 @@ static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
 {
 	char pin;
 	int irq;
-
-
+	
+	
 	pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &pin);
 	irq = pin-1;
-
+	
 	switch (PCI_DEV(dev)) {
 	case 20:
 		break;
@@ -115,20 +115,20 @@ static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
 	case 17:
 		irq+=3;
 		break;
-	default:
+	default: 
 		return;
 	}
-
+	
 	irq&=3; /* wrap around */
 	irq+=9; /* lowest IRQ is 9 */
-
+	
 	pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, irq);
-#if 0
-	printf("fixup_irq: device %d pin %c irq %d\n",
+#if 0	
+	printf("fixup_irq: device %d pin %c irq %d\n", 
 	       PCI_DEV(dev), 'A' + pin -1, irq);
 #endif
 }
-
+ 
 static struct pci_controller sc520_cdp_hose = {
 	fixup_irq: pci_sc520_cdp_fixup_irq,
 };
@@ -147,7 +147,7 @@ static void silence_uart(int port)
 void setup_ali_sio(int uart_primary)
 {
 	ali512x_init();
-
+	
 	ali512x_set_fdc(ALI_ENABLED, 0x3f2, 6, 0);
 	ali512x_set_pp(ALI_ENABLED, 0x278, 7, 3);
 	ali512x_set_uart(ALI_ENABLED, ALI_UART1, uart_primary?0x3f8:0x3e8, 4);
@@ -155,21 +155,21 @@ void setup_ali_sio(int uart_primary)
 	ali512x_set_rtc(ALI_DISABLED, 0, 0);
 	ali512x_set_kbc(ALI_ENABLED, 1, 12);
 	ali512x_set_cio(ALI_ENABLED);
-
+	
 	/* IrDa pins */
 	ali512x_cio_function(12, 1, 0, 0);
 	ali512x_cio_function(13, 1, 0, 0);
-
+	
 	/* SSI chip select pins */
 	ali512x_cio_function(14, 0, 0, 0);  /* SSI_CS */
-	ali512x_cio_function(15, 0, 0, 0);  /* SSI_MV */
+	ali512x_cio_function(15, 0, 0, 0);  /* SSI_MV */					     
 	ali512x_cio_function(16, 0, 1, 0);  /* SSI_SPI# (inverted) */
 
 	/* Board REV pins */
 	ali512x_cio_function(20, 0, 0, 1);
 	ali512x_cio_function(21, 0, 0, 1);
 	ali512x_cio_function(22, 0, 0, 1);
-	ali512x_cio_function(23, 0, 0, 1);
+	ali512x_cio_function(23, 0, 0, 1);      
 }
 
 
@@ -178,13 +178,13 @@ static void bus_init(void)
 {
 
 	/* set up the GP IO pins */
-	write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); 	/* set the GPIO pin function 31-16 reg */
+	write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); 	/* set the GPIO pin function 31-16 reg */		   
 	write_mmcr_word(SC520_PIOPFS15_0, 0xffff);  	/* set the GPIO pin function 15-0 reg */
-	write_mmcr_byte(SC520_CSPFS, 0xf8);  		/* set the CS pin function  reg */
+	write_mmcr_byte(SC520_CSPFS, 0xf8);  		/* set the CS pin function  reg */	
 	write_mmcr_byte(SC520_CLKSEL, 0x70);
 
-
-	write_mmcr_byte(SC520_GPCSRT, 1);   /* set the GP CS offset */
+	
+	write_mmcr_byte(SC520_GPCSRT, 1);   /* set the GP CS offset */    	
 	write_mmcr_byte(SC520_GPCSPW, 3);   /* set the GP CS pulse width */
 	write_mmcr_byte(SC520_GPCSOFF, 1);  /* set the GP CS offset */
 	write_mmcr_byte(SC520_GPRDW, 3);    /* set the RD pulse width */
@@ -192,40 +192,40 @@ static void bus_init(void)
         write_mmcr_byte(SC520_GPWRW, 3);    /* set the GP WR pulse width */
 	write_mmcr_byte(SC520_GPWROFF, 1);  /* set the GP WR offset */
 
-	write_mmcr_word(SC520_BOOTCSCTL, 0x1823);		/* set up timing of BOOTCS */
+	write_mmcr_word(SC520_BOOTCSCTL, 0x1823);		/* set up timing of BOOTCS */ 
 	write_mmcr_word(SC520_ROMCS1CTL, 0x1823);		/* set up timing of ROMCS1 */
-	write_mmcr_word(SC520_ROMCS2CTL, 0x1823);		/* set up timing of ROMCS2 */
-
+	write_mmcr_word(SC520_ROMCS2CTL, 0x1823);		/* set up timing of ROMCS2 */ 
+	
 	/* adjust the memory map:
 	 * by default the first 256MB (0x00000000 - 0x0fffffff) is mapped to SDRAM
 	 * and 256MB to 1G-128k  (0x1000000 - 0x37ffffff) is mapped to PCI mmio
-	 * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */
-
-
+	 * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */ 
+	
+		
 	/* SRAM = GPCS3 128k @ d0000-effff*/
-	write_mmcr_long(SC520_PAR2,  0x4e00400d);
-
+	write_mmcr_long(SC520_PAR2,  0x4e00400d);		
+	
 	/* IDE0 = GPCS6 1f0-1f7 */
-	write_mmcr_long(SC520_PAR3,  0x380801f0);
+	write_mmcr_long(SC520_PAR3,  0x380801f0);		
 
 	/* IDE1 = GPCS7 3f6 */
-	write_mmcr_long(SC520_PAR4,  0x3c0003f6);
+	write_mmcr_long(SC520_PAR4,  0x3c0003f6);		
 	/* bootcs */
-	write_mmcr_long(SC520_PAR12, 0x8bffe800);
+	write_mmcr_long(SC520_PAR12, 0x8bffe800);		
 	/* romcs2 */
-	write_mmcr_long(SC520_PAR13, 0xcbfff000);
+	write_mmcr_long(SC520_PAR13, 0xcbfff000);		
 	/* romcs1 */
-	write_mmcr_long(SC520_PAR14, 0xabfff800);
+	write_mmcr_long(SC520_PAR14, 0xabfff800);		
 	/* 680 LEDS */
-	write_mmcr_long(SC520_PAR15, 0x30000640);
-
-	asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
+	write_mmcr_long(SC520_PAR15, 0x30000640);		
+	
+	asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */	
 
 	if (CFG_USE_SIO_UART) {
-		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
+		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);	
 		setup_ali_sio(1);
 	} else {
-		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
+		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));	
 		setup_ali_sio(0);
 		silence_uart(0x3e8);
 		silence_uart(0x2e8);
@@ -242,21 +242,21 @@ static void bus_init(void)
 int board_init(void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
-
-	init_sc520();
+	
+	init_sc520();	
 	bus_init();
 	irq_init();
-
+		
 	/* max drive current on SDRAM */
 	write_mmcr_word(SC520_DSCTL, 0x0100);
-
+		
 	/* enter debug mode after next reset (only if jumper is also set) */
 	write_mmcr_byte(SC520_RESCFG, 0x08);
-
+	
 	/* configure the software timer to 33.333MHz */
 	write_mmcr_byte(SC520_SWTMRCFG, 0);
 	gd->bus_clk = 33333000;
-
+	
 	return 0;
 }
 
@@ -277,14 +277,14 @@ int last_stage_init(void)
 {
 	int minor;
 	int major;
-
+	
 	major = minor = 0;
 	major |= ali512x_cio_in(23)?2:0;
 	major |= ali512x_cio_in(22)?1:0;
 	minor |= ali512x_cio_in(21)?2:0;
 	minor |= ali512x_cio_in(20)?1:0;
-
+	
 	printf("AMD SC520 CDP revision %d.%d\n", major, minor);
-
+	
 	return 0;
 }