powerpc: ppc4xx: remove alpr support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>

8 files changed, 0 insertions, 674 deletions

diff --git a/board/prodrive/alpr/Kconfig b/board/prodrive/alpr/Kconfig
deleted file mode 100644
index 543b4557eef..00000000000
--- a/board/prodrive/alpr/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_ALPR
-
-config SYS_BOARD
-	default "alpr"
-
-config SYS_VENDOR
-	default "prodrive"
-
-config SYS_CONFIG_NAME
-	default "alpr"
-
-endif
diff --git a/board/prodrive/alpr/MAINTAINERS b/board/prodrive/alpr/MAINTAINERS
deleted file mode 100644
index 31baabb67e6..00000000000
--- a/board/prodrive/alpr/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ALPR BOARD
-M:	Stefan Roese <sr@denx.de>
-S:	Maintained
-F:	board/prodrive/alpr/
-F:	include/configs/alpr.h
-F:	configs/alpr_defconfig
diff --git a/board/prodrive/alpr/Makefile b/board/prodrive/alpr/Makefile
deleted file mode 100644
index 812d041ef2d..00000000000
--- a/board/prodrive/alpr/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= alpr.o fpga.o nand.o
-extra-y	+= init.o
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
deleted file mode 100644
index 31c1ab5d0f5..00000000000
--- a/board/prodrive/alpr/alpr.c
+++ /dev/null
@@ -1,215 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-
-#include <common.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <spd_sdram.h>
-#include <asm/ppc4xx-emac.h>
-#include <miiphy.h>
-#include <asm/processor.h>
-#include <asm/4xx_pci.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern int alpr_fpga_init(void);
-
-int board_early_init_f (void)
-{
-	/*-------------------------------------------------------------------------
-	 * Initialize EBC CONFIG
-	 *-------------------------------------------------------------------------*/
-	mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
-	      EBC_CFG_PTD_DISABLE | EBC_CFG_RTC_64PERCLK |
-	      EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
-	      EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
-	      EBC_CFG_PME_DISABLE | EBC_CFG_PR_32);
-
-	/*--------------------------------------------------------------------
-	 * Setup the interrupt controller polarities, triggers, etc.
-	 *-------------------------------------------------------------------*/
-	/*
-	 * Because of the interrupt handling rework to handle 440GX interrupts
-	 * with the common code, we needed to change names of the UIC registers.
-	 * Here the new relationship:
-	 *
-	 * U-Boot name	440GX name
-	 * -----------------------
-	 * UIC0		UICB0
-	 * UIC1		UIC0
-	 * UIC2		UIC1
-	 * UIC3		UIC2
-	 */
-	mtdcr (UIC1SR, 0xffffffff);	/* clear all */
-	mtdcr (UIC1ER, 0x00000000);	/* disable all */
-	mtdcr (UIC1CR, 0x00000009);	/* SMI & UIC1 crit are critical */
-	mtdcr (UIC1PR, 0xfffffe03);	/* per manual */
-	mtdcr (UIC1TR, 0x01c00000);	/* per manual */
-	mtdcr (UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr (UIC1SR, 0xffffffff);	/* clear all */
-
-	mtdcr (UIC2SR, 0xffffffff);	/* clear all */
-	mtdcr (UIC2ER, 0x00000000);	/* disable all */
-	mtdcr (UIC2CR, 0x00000000);	/* all non-critical */
-	mtdcr (UIC2PR, 0xffffe0ff);	/* per ref-board manual */
-	mtdcr (UIC2TR, 0x00ffc000);	/* per ref-board manual */
-	mtdcr (UIC2VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr (UIC2SR, 0xffffffff);	/* clear all */
-
-	mtdcr (UIC3SR, 0xffffffff);	/* clear all */
-	mtdcr (UIC3ER, 0x00000000);	/* disable all */
-	mtdcr (UIC3CR, 0x00000000);	/* all non-critical */
-	mtdcr (UIC3PR, 0xffffffff);	/* per ref-board manual */
-	mtdcr (UIC3TR, 0x00ff8c0f);	/* per ref-board manual */
-	mtdcr (UIC3VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr (UIC3SR, 0xffffffff);	/* clear all */
-
-	mtdcr (UIC0SR, 0xfc000000); /* clear all */
-	mtdcr (UIC0ER, 0x00000000); /* disable all */
-	mtdcr (UIC0CR, 0x00000000); /* all non-critical */
-	mtdcr (UIC0PR, 0xfc000000); /* */
-	mtdcr (UIC0TR, 0x00000000); /* */
-	mtdcr (UIC0VR, 0x00000001); /* */
-
-	/* Setup shutdown/SSD empty interrupt as inputs */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
-	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
-
-	/* Setup GPIO/IRQ multiplexing */
-	mtsdr(SDR0_PFC0, 0x01a33e00);
-
-	return 0;
-}
-
-int last_stage_init(void)
-{
-	unsigned short reg;
-
-	/*
-	 * Configure LED's of both Marvell 88E1111 PHY's
-	 *
-	 * This has to be done after the 4xx ethernet driver is loaded,
-	 * so "last_stage_init()" is the right place.
-	 */
-	miiphy_read("ppc_4xx_eth2", CONFIG_PHY2_ADDR, 0x18, &reg);
-	reg |= 0x0001;
-	miiphy_write("ppc_4xx_eth2", CONFIG_PHY2_ADDR, 0x18, reg);
-	miiphy_read("ppc_4xx_eth3", CONFIG_PHY3_ADDR, 0x18, &reg);
-	reg |= 0x0001;
-	miiphy_write("ppc_4xx_eth3", CONFIG_PHY3_ADDR, 0x18, reg);
-
-	return 0;
-}
-
-static int board_rev(void)
-{
-	/* Setup as input */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~(CONFIG_SYS_GPIO_REV0 | CONFIG_SYS_GPIO_REV1));
-	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_REV0 | CONFIG_SYS_GPIO_REV1));
-
-	return (in32(GPIO0_IR) >> 16) & 0x3;
-}
-
-int checkboard (void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	printf ("Board: ALPR");
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	printf(" (Rev. %d)\n", board_rev());
-
-	return (0);
-}
-
-#if defined(CONFIG_PCI)
-/*
- * Override weak pci_pre_init()
- */
-int pci_pre_init(struct pci_controller *hose)
-{
-	if (__pci_pre_init(hose) == 0)
-		return 0;
-
-	/* FPGA Init */
-	alpr_fpga_init();
-
-	return 1;
-}
-
-/*************************************************************************
- * Override weak is_pci_host()
- *
- *	This routine is called to determine if a pci scan should be
- *	performed. With various hardware environments (especially cPCI and
- *	PPMC) it's insufficient to depend on the state of the arbiter enable
- *	bit in the strap register, or generic host/adapter assumptions.
- *
- *	Rather than hard-code a bad assumption in the general 440 code, the
- *	440 pci code requires the board to decide at runtime.
- *
- *	Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-static void wait_for_pci_ready(void)
-{
-	/*
-	 * Configure EREADY as input
-	 */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~CONFIG_SYS_GPIO_EREADY);
-	udelay(1000);
-
-	for (;;) {
-		if (in32(GPIO0_IR) & CONFIG_SYS_GPIO_EREADY)
-			return;
-	}
-
-}
-
-int is_pci_host(struct pci_controller *hose)
-{
-	wait_for_pci_ready();
-	return 1;		/* return 1 for host controller */
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- *  pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440 PCI Master configuration.
-	  | Map PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xCFFFFFFF ==> PCI address 0x80000000-0xCFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r( PCIL0_POM0SA, 0 ); /* disable */
-	out32r( PCIL0_POM1SA, 0 ); /* disable */
-	out32r( PCIL0_POM2SA, 0 ); /* disable */
-
-	out32r(PCIL0_POM0LAL, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_POM0LAH, 0x00000003);	/* PMM0 Local Address */
-	out32r(PCIL0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_POM0PCIAH, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_POM0SA, ~(0x10000000 - 1) | 1);	/* 256MB + enable region */
-
-	out32r(PCIL0_POM1LAL, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 Local Address */
-	out32r(PCIL0_POM1LAH, 0x00000003);	/* PMM0 Local Address */
-	out32r(PCIL0_POM1PCIAL, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_POM1PCIAH, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_POM1SA, ~(0x10000000 - 1) | 1);	/* 256MB + enable region */
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
diff --git a/board/prodrive/alpr/config.mk b/board/prodrive/alpr/config.mk
deleted file mode 100644
index 0ccb2e669c0..00000000000
--- a/board/prodrive/alpr/config.mk
+++ /dev/null
@@ -1,16 +0,0 @@
-#
-# (C) Copyright 2004
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
-endif
diff --git a/board/prodrive/alpr/fpga.c b/board/prodrive/alpr/fpga.c
deleted file mode 100644
index 3133f942733..00000000000
--- a/board/prodrive/alpr/fpga.c
+++ /dev/null
@@ -1,239 +0,0 @@
-/*
- * (C) Copyright 2006
- * Heiko Schocher, DENX Software Engineering, hs@denx.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Altera FPGA configuration support for the ALPR computer from prodrive
- */
-
-#include <common.h>
-#include <altera.h>
-#include <ACEX1K.h>
-#include <command.h>
-#include <asm/processor.h>
-#include <asm/ppc440.h>
-#include "fpga.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_FPGA)
-
-#ifdef FPGA_DEBUG
-#define	PRINTF(fmt, args...)	printf(fmt , ##args)
-#else
-#define	PRINTF(fmt, args...)
-#endif
-
-static unsigned long regval;
-
-#define SET_GPIO_REG_0(reg, bit) do {				\
-		regval = in32(reg);				\
-		regval &= ~(0x80000000 >> bit);			\
-		out32(reg, regval);				\
-	} while (0)
-
-#define SET_GPIO_REG_1(reg, bit) do {				\
-		regval = in32(reg);				\
-		regval |= (0x80000000 >> bit);			\
-		out32(reg, regval);				\
-	} while (0)
-
-#define	SET_GPIO_0(bit)		SET_GPIO_REG_0(GPIO0_OR, bit)
-#define	SET_GPIO_1(bit)		SET_GPIO_REG_1(GPIO0_OR, bit)
-
-#define FPGA_PRG		(0x80000000 >> CONFIG_SYS_GPIO_PROG_EN)
-#define FPGA_CONFIG		(0x80000000 >> CONFIG_SYS_GPIO_CONFIG)
-#define FPGA_DATA		(0x80000000 >> CONFIG_SYS_GPIO_DATA)
-#define FPGA_CLK		(0x80000000 >> CONFIG_SYS_GPIO_CLK)
-#define OLD_VAL			(FPGA_PRG | FPGA_CONFIG)
-
-#define SET_FPGA(data)		out32(GPIO0_OR, data)
-
-#define FPGA_WRITE_1 do {							    \
-	SET_FPGA(OLD_VAL | 0	    | FPGA_DATA);	/* set data to 1 */ \
-	SET_FPGA(OLD_VAL | FPGA_CLK | FPGA_DATA);	/* set data to 1 */ \
-} while (0)
-
-#define FPGA_WRITE_0 do {							    \
-	SET_FPGA(OLD_VAL | 0	    | 0);		/* set data to 0 */ \
-	SET_FPGA(OLD_VAL | FPGA_CLK | 0);		/* set data to 1 */ \
-} while (0)
-
-/* Plattforminitializations */
-/* Here we have to set the FPGA Chain */
-/* PROGRAM_PROG_EN	= HIGH */
-/* PROGRAM_SEL_DPR	= LOW */
-int fpga_pre_fn(int cookie)
-{
-	/* Enable the FPGA Chain */
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_PROG_EN);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_PROG_EN);
-	SET_GPIO_1(CONFIG_SYS_GPIO_PROG_EN);
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_SEL_DPR);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_SEL_DPR);
-	SET_GPIO_0((CONFIG_SYS_GPIO_SEL_DPR));
-
-	/* initialize the GPIO Pins */
-	/* output */
-	SET_GPIO_0(CONFIG_SYS_GPIO_CLK);
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_CLK);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CLK);
-
-	/* output */
-	SET_GPIO_0(CONFIG_SYS_GPIO_DATA);
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_DATA);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_DATA);
-
-	/* First we set STATUS to 0 then as an input */
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_STATUS);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_STATUS);
-	SET_GPIO_0(CONFIG_SYS_GPIO_STATUS);
-	SET_GPIO_REG_0(GPIO0_TCR, CONFIG_SYS_GPIO_STATUS);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_STATUS);
-
-	/* output */
-	SET_GPIO_REG_1(GPIO0_TCR, CONFIG_SYS_GPIO_CONFIG);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CONFIG);
-	SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
-
-	/* input */
-	SET_GPIO_0(CONFIG_SYS_GPIO_CON_DON);
-	SET_GPIO_REG_0(GPIO0_TCR, CONFIG_SYS_GPIO_CON_DON);
-	SET_GPIO_REG_0(GPIO0_ODR, CONFIG_SYS_GPIO_CON_DON);
-
-	/* CONFIG = 0 STATUS = 0 -> FPGA in reset state */
-	SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
-	return FPGA_SUCCESS;
-}
-
-/* Set the state of CONFIG Pin */
-int fpga_config_fn(int assert_config, int flush, int cookie)
-{
-	if (assert_config)
-		SET_GPIO_1(CONFIG_SYS_GPIO_CONFIG);
-	else
-		SET_GPIO_0(CONFIG_SYS_GPIO_CONFIG);
-
-	return FPGA_SUCCESS;
-}
-
-/* Returns the state of STATUS Pin */
-int fpga_status_fn(int cookie)
-{
-	unsigned long	reg;
-
-	reg = in32(GPIO0_IR);
-	if (reg & (0x80000000 >> CONFIG_SYS_GPIO_STATUS)) {
-		PRINTF("STATUS = HIGH\n");
-		return FPGA_FAIL;
-	}
-	PRINTF("STATUS = LOW\n");
-	return FPGA_SUCCESS;
-}
-
-/* Returns the state of CONF_DONE Pin */
-int fpga_done_fn(int cookie)
-{
-	unsigned long	reg;
-	reg = in32(GPIO0_IR);
-	if (reg & (0x80000000 >> CONFIG_SYS_GPIO_CON_DON)) {
-		PRINTF("CONF_DON = HIGH\n");
-		return FPGA_FAIL;
-	}
-	PRINTF("CONF_DON = LOW\n");
-	return FPGA_SUCCESS;
-}
-
-/* writes the complete buffer to the FPGA
-   writing the complete buffer in one function is much faster,
-   then calling it for every bit */
-int fpga_write_fn(const void *buf, size_t len, int flush, int cookie)
-{
-	size_t bytecount = 0;
-	unsigned char *data = (unsigned char *) buf;
-	unsigned char val = 0;
-	int		i;
-	int len_40 = len / 40;
-
-	while (bytecount < len) {
-		val = data[bytecount++];
-		i = 8;
-		do {
-			if (val & 0x01)
-				FPGA_WRITE_1;
-			else
-				FPGA_WRITE_0;
-
-			val >>= 1;
-			i--;
-		} while (i > 0);
-
-#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
-		if (bytecount % len_40 == 0) {
-			putc('.');		/* let them know we are alive */
-#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
-			if (ctrlc())
-				return FPGA_FAIL;
-#endif
-		}
-#endif
-	}
-	return FPGA_SUCCESS;
-}
-
-/* called, when programming is aborted */
-int fpga_abort_fn(int cookie)
-{
-	SET_GPIO_1((CONFIG_SYS_GPIO_SEL_DPR));
-	return FPGA_SUCCESS;
-}
-
-/* called, when programming was succesful */
-int fpga_post_fn(int cookie)
-{
-	return fpga_abort_fn(cookie);
-}
-
-/* Note that these are pointers to code that is in Flash.  They will be
- * relocated at runtime.
- */
-Altera_CYC2_Passive_Serial_fns fpga_fns = {
-	fpga_pre_fn,
-	fpga_config_fn,
-	fpga_status_fn,
-	fpga_done_fn,
-	fpga_write_fn,
-	fpga_abort_fn,
-	fpga_post_fn
-};
-
-Altera_desc fpga[CONFIG_FPGA_COUNT] = {
-	{Altera_CYC2,
-	 passive_serial,
-	 Altera_EP2C35_SIZE,
-	 (void *) &fpga_fns,
-	 NULL,
-	 0}
-};
-
-/*
- * Initialize the fpga.  Return 1 on success, 0 on failure.
- */
-int alpr_fpga_init(void)
-{
-	int i;
-
-	PRINTF("%s:%d: Initialize FPGA interface\n", __func__, __LINE__);
-	fpga_init();
-
-	for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
-		PRINTF("%s:%d: Adding fpga %d\n", __func__, __LINE__, i);
-		fpga_add(fpga_altera, &fpga[i]);
-	}
-	return 1;
-}
-
-#endif
diff --git a/board/prodrive/alpr/init.S b/board/prodrive/alpr/init.S
deleted file mode 100644
index 7ff7a59170e..00000000000
--- a/board/prodrive/alpr/init.S
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <asm-offsets.h>
-#include <ppc_asm.tmpl>
-#include <asm/mmu.h>
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- *  Pointer to the table is returned in r1
- *
- *************************************************************************/
-
-	.section .bootpg,"ax"
-	.globl tlbtab
-
-tlbtab:
-	tlbtab_start
-	tlbentry(0xff000000, SZ_16M, 0xff000000, 1, AC_RWX | SA_IG )
-	tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_RW | SA_IG)
-	tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_RWX)
-	tlbentry(CONFIG_SYS_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_RWX)
-#ifdef CONFIG_4xx_DCACHE
-	tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_G)
-#else
-	tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_IG)
-#endif
-
-#ifdef CONFIG_SYS_INIT_RAM_DCACHE
-	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-	tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
-#endif
-	tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 2, AC_RW | SA_IG)
-
-	/* PCI */
-	tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 3, AC_RW | SA_IG)
-	tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 3, AC_RW | SA_IG)
-	tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 3, AC_RW | SA_IG)
-
-	/* NAND */
-	tlbentry(CONFIG_SYS_NAND_BASE, SZ_4K, CONFIG_SYS_NAND_BASE, 1, AC_RWX | SA_IG)
-	tlbtab_end
diff --git a/board/prodrive/alpr/nand.c b/board/prodrive/alpr/nand.c
deleted file mode 100644
index ca40cea9ad1..00000000000
--- a/board/prodrive/alpr/nand.c
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * (C) Copyright 2006
- * Heiko Schocher, DENX Software Engineering, hs@denx.de
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <asm/processor.h>
-#include <nand.h>
-
-struct alpr_ndfc_regs {
-	u8 cmd[4];
-	u8 addr_wait;
-	u8 term;
-	u8 dummy;
-	u8 dummy2;
-	u8 data;
-};
-
-static u8 hwctl;
-static struct alpr_ndfc_regs *alpr_ndfc = NULL;
-
-#define readb(addr)	(u8)(*(volatile u8 *)(addr))
-#define writeb(d,addr)	*(volatile u8 *)(addr) = ((u8)(d))
-
-/*
- * The ALPR has a NAND Flash Controller (NDFC) that handles all accesses to
- * the NAND devices.  The NDFC has command, address and data registers that
- * when accessed will set up the NAND flash pins appropriately.  We'll use the
- * hwcontrol function to save the configuration in a global variable.
- * We can then use this information in the read and write functions to
- * determine which NDFC register to access.
- *
- * There are 2 NAND devices on the board, a Hynix HY27US08561A (1 GByte).
- */
-static void alpr_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	struct nand_chip *this = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if ( ctrl & NAND_CLE )
-			hwctl |= 0x1;
-		else
-			hwctl &= ~0x1;
-		if ( ctrl & NAND_ALE )
-			hwctl |= 0x2;
-		else
-			hwctl &= ~0x2;
-		if ( (ctrl & NAND_NCE) != NAND_NCE)
-			writeb(0x00, &(alpr_ndfc->term));
-	}
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, this->IO_ADDR_W);
-}
-
-static u_char alpr_nand_read_byte(struct mtd_info *mtd)
-{
-	return readb(&(alpr_ndfc->data));
-}
-
-static void alpr_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
-	struct nand_chip *nand = mtd->priv;
-	int i;
-
-	for (i = 0; i < len; i++) {
-		if (hwctl & 0x1)
-			 /*
-			  * IO_ADDR_W used as CMD[i] reg to support multiple NAND
-			  * chips.
-			  */
-			writeb(buf[i], nand->IO_ADDR_W);
-		else if (hwctl & 0x2)
-			writeb(buf[i], &(alpr_ndfc->addr_wait));
-		else
-			writeb(buf[i], &(alpr_ndfc->data));
-	}
-}
-
-static void alpr_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
-	int i;
-
-	for (i = 0; i < len; i++) {
-		buf[i] = readb(&(alpr_ndfc->data));
-	}
-}
-
-static int alpr_nand_dev_ready(struct mtd_info *mtd)
-{
-	/*
-	 * Blocking read to wait for NAND to be ready
-	 */
-	(void)readb(&(alpr_ndfc->addr_wait));
-
-	/*
-	 * Return always true
-	 */
-	return 1;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
-	alpr_ndfc = (struct alpr_ndfc_regs *)CONFIG_SYS_NAND_BASE;
-
-	nand->ecc.mode = NAND_ECC_SOFT;
-
-	/* Reference hardware control function */
-	nand->cmd_ctrl  = alpr_nand_hwcontrol;
-	nand->read_byte  = alpr_nand_read_byte;
-	nand->write_buf  = alpr_nand_write_buf;
-	nand->read_buf   = alpr_nand_read_buf;
-	nand->dev_ready  = alpr_nand_dev_ready;
-
-	return 0;
-}
-#endif