virtex2 fix for bogus download error messages

The virtex2 FPGA download code watches for init going active during
a download of config data as an error condition. init also goes
active after a configuration is finished in concert with the done
signal. So far, the code does not check for done active until all
of the configuration data is sent. If configuration data has a few
extra pad bytes at the end, this would cause an error message even
though the download had suceeded.
NOTE: virtex2 slave serial and spartan2 versions may still have the
same problem.
Patch by Andrew Dyer, 12 Jan 2005

1 files changed, 20 insertions, 6 deletions

diff --git a/common/virtex2.c b/common/virtex2.c
index bb44eaa6c50..84050694234 100644
--- a/common/virtex2.c
+++ b/common/virtex2.c
@@ -33,6 +33,10 @@
 
 #if (CONFIG_FPGA & (CFG_XILINX | CFG_VIRTEX2))
 
+#if 0
+#define FPGA_DEBUG
+#endif 
+
 #ifdef	FPGA_DEBUG
 #define	PRINTF(fmt,args...)	printf (fmt ,##args)
 #else
@@ -190,7 +194,7 @@ int Virtex2_reloc (Xilinx_desc * desc, ulong reloc_offset)
  *    this process, a configuration error (most likely CRC failure) has
  *    ocurred.  At this point a status word may be read from the
  *    SelectMap interface to determine the source of the problem (You
- *    could, for instance, put this in you 'abort' function handler).
+ *    could, for instance, put this in your 'abort' function handler).
  * 4. After all data has been written, test the state of the FPGA
  *    INIT_B and DONE lines.  If both are high, configuration has
  *    succeeded. Congratulations!
@@ -251,7 +255,7 @@ static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
 		ts = get_timer (0);
 		do {
 			if (get_timer (ts) > CFG_FPGA_WAIT_INIT) {
-				printf ("%s:%d: ** Timeout after %d mS waiting for INIT"
+				printf ("%s:%d: ** Timeout after %d ticks waiting for INIT"
 						" to assert.\n", __FUNCTION__, __LINE__,
 						CFG_FPGA_WAIT_INIT);
 				(*fn->abort) (cookie);
@@ -270,7 +274,7 @@ static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
 		do {
 			CONFIG_FPGA_DELAY ();
 			if (get_timer (ts) > CFG_FPGA_WAIT_INIT) {
-				printf ("%s:%d: ** Timeout after %d mS waiting for INIT"
+				printf ("%s:%d: ** Timeout after %d ticks waiting for INIT"
 						" to deassert.\n", __FUNCTION__, __LINE__,
 						CFG_FPGA_WAIT_INIT);
 				(*fn->abort) (cookie);
@@ -293,14 +297,24 @@ static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
 				return FPGA_FAIL;
 			}
 #endif
+
+			if ((*fn->done) (cookie) == FPGA_SUCCESS) {
+			    PRINTF ("%s:%d:done went active early, bytecount = %d\n",
+				    __FUNCTION__, __LINE__, bytecount);
+			    break;
+			}
+
 #ifdef CFG_FPGA_CHECK_ERROR
 			if ((*fn->init) (cookie)) {
-				printf ("%s:%d:  ** Error: INIT asserted during"
+				printf ("\n%s:%d:  ** Error: INIT asserted during"
 						" configuration\n", __FUNCTION__, __LINE__);
+				printf ("%d = buffer offset, %d = buffer size\n",
+					bytecount, bsize);
 				(*fn->abort) (cookie);
 				return FPGA_FAIL;
 			}
 #endif
+
 			(*fn->wdata) (data[bytecount++], TRUE, cookie);
 			CONFIG_FPGA_DELAY ();
 
@@ -315,7 +329,7 @@ static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
 			ts = get_timer (0);
 			while ((*fn->busy) (cookie)) {
 				if (get_timer (ts) > CFG_FPGA_WAIT_BUSY) {
-					printf ("%s:%d: ** Timeout after %d mS waiting for"
+					printf ("%s:%d: ** Timeout after %d ticks waiting for"
 							" BUSY to deassert\n",
 							__FUNCTION__, __LINE__, CFG_FPGA_WAIT_BUSY);
 					(*fn->abort) (cookie);
@@ -349,7 +363,7 @@ static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
 		ret_val = FPGA_SUCCESS;
 		while (((*fn->done) (cookie) == FPGA_FAIL) || (*fn->init) (cookie)) {
 			if (get_timer (ts) > CFG_FPGA_WAIT_CONFIG) {
-				printf ("%s:%d: ** Timeout after %d mS waiting for DONE to"
+				printf ("%s:%d: ** Timeout after %d ticks waiting for DONE to"
 						"assert and INIT to deassert\n",
 						__FUNCTION__, __LINE__, CFG_FPGA_WAIT_CONFIG);
 				(*fn->abort) (cookie);