Add README file for mpc7448hpc2 board.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

1 files changed, 193 insertions, 0 deletions

diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2
new file mode 100644
index 00000000000..5142a0f6385
--- /dev/null
+++ b/doc/README.mpc7448hpc2
@@ -0,0 +1,193 @@
+Freescale MPC7448hpc2 (Taiga) board
+===================================
+
+Created 08/11/2006 Roy Zang
+--------------------------
+MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference 
+design, which is optimized for high speed throughput between the processor and 
+the memory, disk drive and Ethernet port subsystems.
+
+MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be 
+used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX 
+chassis.
+
+Building U-Boot
+------------------
+The mpc7448hpc2 code base is known to compile using:
+    Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
+
+    $ make mpc7448hpc2_config
+    Configuring for mpc7448hpc2 board...
+
+    $ make
+
+Memory Map
+----------
+
+The memory map is setup for Linux to operate properly.
+
+The mapping is:
+
+   Range Start     Range End       Definition              	Size
+
+   0x0000_0000     0x7fff_ffff     DDR                     	2G
+   0xe000_0000     0xe7ff_ffff     PCI Memory              	128M
+   0xfa00_0000     0xfaff_ffff     PCI IO                  	16M
+   0xfb00_0000     0xfbff_ffff     PCI Config              	16M
+   0xfc00_0000     0xfc0f_ffff     NVRAM/CADMUS            	1M
+   0xfe00_0000	   0xfeff_ffff	   PromJet		   	16M
+   0xff00_0000     0xff80_0000     FLASH (boot flash)      	8M
+   0xff80_0000     0xffff_ffff     FLASH (second half flash)	8M
+
+
+Using Flash
+-----------
+
+The MPC7448hpc2 board has two "banks" of flash, each 8MB in size 
+(2^23 = 0x00800000). 
+
+Note: the "bank" here refers to half of the flash. In fact, there is only one 
+bank of flash, which is divided into low and high half. Each is controlled by
+the most significant bit of the address bus. The so called "bank" is only for
+convenience.
+
+There is a switch which allows the "bank" to be selected.  The switch
+settings for updating flash are given below.
+
+The u-boot commands for copying the boot-bank into the secondary bank are
+as follows:
+
+     erase ff800000 ff880000
+     cp.b ff000000 ff800000 80000
+
+U-boot commands for downloading an image via tftp and flashing
+it into the secondary bank:
+
+     tftp 10000 <u-boot.bin.image>
+     erase ff000000 ff080000
+     cp.b 10000 ff000000 80000
+
+
+After copying the image into the second bank of flash, be sure to toggle
+SW3[4] on board before resetting the board in order to set the
+secondary bank as the boot-bank.
+
+
+Board Switches
+----------------------
+
+
+Most switches on the board should not be changed.  The most frequent
+user-settable switches on the board are used to configure
+the flash banks and determining the PCI frequency.
+
+SW1[1-5]: Processor core voltage
+
+      12345		Core Voltage
+      -----
+  SW1=01111	   	   1.000V.
+  SW1=01101	   	   1.100V.
+  SW1=01011	   	   1.200V.
+  SW1=01001	   	   1.300V only for MPC7447A.
+
+
+SW2[1-6]: CPU core frequency
+
+		  CPU Core Frequency (MHz)
+			Bus Frequency
+      123456	100	133	167	200	 Ratio
+	
+      ------
+  SW2=101100	500	667	833	1000	   5x
+  SW2=100100	550	733	917	1100	   5.5x
+  SW2=110100	600	800	1000	1200	   6x
+  SW2=010100	650	866	1083	1300	   6.5x
+  SW2=001000	700	930	1167	1400	   7x
+  SW2=000100	750	1000	1250	1500	   7.5x
+  SW2=110000	800	1066	1333	1600	   8x
+  SW2=011000	850	1333	1417	1700	   8.5x only for MPC7447A
+  SW2=011110	900	1200	1500	1800	   9x
+
+This table shows only a subset of available frequency options; see the CPU 
+hardware specifications for more information.
+
+
+SW2[7-8]: Bus Protocol and CPU Reset Option
+
+      7		
+      -
+  SW2=0	   	System bus uses MPX bus protocol
+  SW2=1		System bus uses 60x bus protocol
+
+      8		
+      -
+  SW2=0	   	TSI108 can cause CPU reset
+  SW2=1		TSI108 can not cause CPU reset
+
+
+SW3[1-8] system options
+
+      123		
+      ---
+  SW3=xxx	   	Connected to GPIO[0:2] on TSI108
+
+      4		
+      -
+  SW3=0	   	CPU boots from low half of flash
+  SW3=1		CPU boots from high half of flash
+
+      5		
+      -
+  SW3=0	   	SATA and slot2 connected to PCI bus
+  SW3=1		Only slot1 connected to PCI bus
+
+      6		
+      -
+  SW3=0	   	USB connected to PCI bus
+  SW3=1		USB disconnected from PCI bus
+
+      7		
+      -
+  SW3=0	   	Flash is write protected
+  SW3=1		Flash is NOT write protected
+
+      8		
+      -
+  SW3=0	   	CPU will boot from flash
+  SW3=1		CPU will boot from PromJet
+
+SW4[1-3]: System bus frequency
+
+			Bus Frequency (MHz)
+      ---
+  SW4=010			183
+  SW4=011			100
+  SW4=100			133
+  SW4=101			166 only for MPC7447A
+  SW4=110			200 only for MPC7448
+  others			reserved
+	
+
+SW4[4-6]: DDR2 SDRAM frequency
+
+			Bus Frequency (MHz)
+      ---
+  SW4=000		   external clock
+  SW4=011		   system clock	
+  SW4=100			133
+  SW4=101			166
+  SW4=110			200
+  others			reserved
+
+
+SW4[7-8]: PCI/PCI-X frequency control
+      7		
+      -
+  SW4=0	   	PCI/PCI-X bus operates normally
+  SW4=1		PCI bus forced to PCI-33 mode
+
+      8		
+      -
+  SW4=0	   	PCI-X mode at 133 MHz allowed
+  SW4=1		PCI-X mode limited to 100 MHz
+