xilinx: zynq: Add support to secure images

This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
   authenticated or encrypted or both authenticated and encrypted
   image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
   image back to DDR as per destination address. The image has
   to be encrypted using xilinx bootgen tool and to get only the
   encrypted image from tool use -split option while invoking
   bootgen.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

1 files changed, 45 insertions, 0 deletions

diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
index fd37d18c7f4..6409d3024ea 100644
--- a/drivers/fpga/zynqpl.c
+++ b/drivers/fpga/zynqpl.c
@@ -17,6 +17,7 @@
 
 #define DEVCFG_CTRL_PCFG_PROG_B		0x40000000
 #define DEVCFG_CTRL_PCFG_AES_EFUSE_MASK	0x00001000
+#define DEVCFG_CTRL_PCAP_RATE_EN_MASK	0x02000000
 #define DEVCFG_ISR_FATAL_ERROR_MASK	0x00740040
 #define DEVCFG_ISR_ERROR_FLAGS_MASK	0x00340840
 #define DEVCFG_ISR_RX_FIFO_OV		0x00040000
@@ -497,3 +498,47 @@ struct xilinx_fpga_op zynq_op = {
 	.loadfs = zynq_loadfs,
 #endif
 };
+
+#ifdef CONFIG_CMD_ZYNQ_AES
+/*
+ * Load the encrypted image from src addr and decrypt the image and
+ * place it back the decrypted image into dstaddr.
+ */
+int zynq_decrypt_load(u32 srcaddr, u32 srclen, u32 dstaddr, u32 dstlen)
+{
+	if (srcaddr < SZ_1M || dstaddr < SZ_1M) {
+		printf("%s: src and dst addr should be > 1M\n",
+		       __func__);
+		return FPGA_FAIL;
+	}
+
+	if (zynq_dma_xfer_init(BIT_NONE)) {
+		printf("%s: zynq_dma_xfer_init FAIL\n", __func__);
+		return FPGA_FAIL;
+	}
+
+	writel((readl(&devcfg_base->ctrl) | DEVCFG_CTRL_PCAP_RATE_EN_MASK),
+	       &devcfg_base->ctrl);
+
+	debug("%s: Source = 0x%08X\n", __func__, (u32)srcaddr);
+	debug("%s: Size = %zu\n", __func__, srclen);
+
+	/* flush(clean & invalidate) d-cache range buf */
+	flush_dcache_range((u32)srcaddr, (u32)srcaddr +
+			roundup(srclen << 2, ARCH_DMA_MINALIGN));
+	/*
+	 * Flush destination address range only if image is not
+	 * bitstream.
+	 */
+	flush_dcache_range((u32)dstaddr, (u32)dstaddr +
+			   roundup(dstlen << 2, ARCH_DMA_MINALIGN));
+
+	if (zynq_dma_transfer(srcaddr | 1, srclen, dstaddr | 1, dstlen))
+		return FPGA_FAIL;
+
+	writel((readl(&devcfg_base->ctrl) & ~DEVCFG_CTRL_PCAP_RATE_EN_MASK),
+	       &devcfg_base->ctrl);
+
+	return FPGA_SUCCESS;
+}
+#endif