diff options
| author | Masahiro Yamada <yamada.m@jp.panasonic.com> | 2014-04-04 15:25:03 +0900 |
|---|---|---|
| committer | Tom Rini <trini@ti.com> | 2014-04-18 10:42:29 -0400 |
| commit | d6b11fd1f0ef1b6cbc81ca7655c47bf68a16f32d (patch) | |
| tree | 7842ceb3aa2ed0178611d168da341cace09dafca /include/commproc.h | |
| parent | a146e8b189abf73b8bac0bfa9c8c3c1b3bfe5507 (diff) | |
powerpc: remove MBX and MBX860T boards support
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Diffstat (limited to 'include/commproc.h')
| -rw-r--r-- | include/commproc.h | 32 |
1 files changed, 0 insertions, 32 deletions
diff --git a/include/commproc.h b/include/commproc.h index 12b94210607..62468c30aad 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -12,10 +12,6 @@ * CPM capabilities. I (or someone else) will add definitions as they * are needed. -- Dan * - * On the MBX board, EPPC-Bug loads CPM microcode into the first 512 - * bytes of the DP RAM and relocates the I2C parameter area to the - * IDMA1 space. The remaining DP RAM is available for buffer descriptors - * or other use. */ #ifndef __CPM_8XX__ #define __CPM_8XX__ @@ -135,7 +131,6 @@ typedef struct cpm_buf_desc { #define PROFF_SMC2 ((uint)0x0380) /* Define enough so I can at least use the serial port as a UART. - * The MBX uses SMC1 as the host serial port. */ typedef struct smc_uart { ushort smc_rbase; /* Rx Buffer descriptor base address */ @@ -888,33 +883,6 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x00003E00) #endif /* CONFIG_LWMON */ -/*** MBX ************************************************************/ - -#ifdef CONFIG_MBX -/* Bits in parallel I/O port registers that have to be set/cleared - * to configure the pins for SCC1 use. The TCLK and RCLK seem unique - * to the MBX860 board. Any two of the four available clocks could be - * used, and the MPC860 cookbook manual has an example using different - * clock pins. - */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0200) -#define PA_ENET_RCLK ((ushort)0x0800) -#define PC_ENET_TENA ((ushort)0x0001) -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to - * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. - */ -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000003d) -#endif /* CONFIG_MBX */ - /*** KM8XX *********************************************************/ /* The KM8XX Service Module uses SCC3 for Ethernet */ |