powerpc: remove ADS860, FADS823, FADS850SAR, FADS860T support

Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
 - Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
   defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
 - Remove the entries from boards.cfg

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

1 files changed, 0 insertions, 415 deletions

diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h
deleted file mode 100644
index d48460b9f5c..00000000000
--- a/include/configs/FADS850SAR.h
+++ /dev/null
@@ -1,415 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by 8xxrom
- * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * fe000000 -> ffnnnnnn : flash      connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC850		1
-#define CONFIG_MPC850SAR	1
-#define CONFIG_FADS			1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-
-#if 0
-#define MPC8XX_FACT	10				/* Multiply by 10		*/
-#define MPC8XX_XIN	50000000		/* 50 MHz in	*/
-#else
-#define MPC8XX_FACT	12				/* Multiply by 12 */
-#define MPC8XX_XIN	4000000			/* 4 MHz in */
-#endif
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BOOTCOMMAND	"bootm 02880000"	/* autoboot command */
-#define CONFIG_BOOTARGS		" "
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00800000	/* 0 ... 8 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFF000000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define	CONFIG_SYS_SDRAM_SIZE		(4<<20) /* standard FADS has 4M */
-#define CONFIG_SYS_FLASH_BASE		0x02800000
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#if 0
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 128 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
-#define	CONFIG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration						11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer  *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(((MPC8XX_FACT-1) << 20) | \
-				PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR       (SCCR_TBS     | \
-				SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-				SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-				SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR		((uint) 0x02100000)
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM	0x02800000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x00000000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFE00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xffff8110									/* 64Kbyte address space */
-#define CONFIG_SYS_BR1_PRELIM	((BCSR_ADDR) | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13a01114
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR		((uint)0xff020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_FLASH_PD_SHIFT	 28
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      23
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0           ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO               ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE            ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1           ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST            ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-
-#define CONFIG_DRAM_50MHZ		1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD
-
-#endif	/* __CONFIG_H */