MPC8308RDB: minimal support for devboard from Freescale

This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
 Dual UART is supported
 NOR flash is supported
 Both TSEC Ethernet controllers are supported
 PCI Express initialization is supported

The following features are enabled in configuration but not fully tested:
 I2C (used to get the board revision)
 I2C-connected RTC
 VSC7385 switch

There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

1 files changed, 560 insertions, 0 deletions

diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h
new file mode 100644
index 00000000000..6cd5da79502
--- /dev/null
+++ b/include/configs/MPC8308RDB.h
@@ -0,0 +1,560 @@
+/*
+ * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1 /* E300 family */
+#define CONFIG_MPC83xx		1 /* MPC83xx family */
+#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
+#define CONFIG_MPC8308RDB	1 /* MPC8308RDB board specific */
+
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is SoC TSEC
+ * TSEC2 is VSC switch
+ */
+#define CONFIG_TSEC1
+#define CONFIG_VSC7385_ENET
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
+ * We choose the A type silicon as default, so the core is 400Mhz.
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_2X1 |\
+	HRCWL_SVCOD_DIV_2 |\
+	HRCWL_CSB_TO_CLKIN_4X1 |\
+	HRCWL_CORE_TO_CSB_3X1)
+/*
+ * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
+ * in 8308's HRCWH according to the manual, but original Freescale's
+ * code has them and I've expirienced some problems using the board
+ * with BDI3000 attached when I've tried to set these bits to zero
+ * (UART doesn't work after the 'reset run' command).
+ */
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_RL_EXT_LEGACY |\
+	HRCWH_TSEC1M_IN_RGMII |\
+	HRCWH_TSEC2M_IN_RGMII |\
+	HRCWH_BIG_ENDIAN)
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRH	0x01b7d103
+#define CONFIG_SYS_SICRL	0x00000040 /* 3.3V, no delay */
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CONFIG_SYS_IMMR		0xE0000000
+
+/*
+ * SERDES
+ */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1	0xe3000
+
+/*
+ * Arbiter Setup
+ */
+#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
+#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
+#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
+				| DDRCDR_PZ_LOZ \
+				| DDRCDR_NZ_LOZ \
+				| DDRCDR_ODT \
+				| DDRCDR_Q_DRN)
+				/* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+
+#define CONFIG_SYS_DDR_SIZE		128 /* MB */
+
+#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
+				| 0x00010000  /* ODT_WR to CSn */ \
+				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+				/* 0x80010102 */
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
+				| (0 << TIMING_CFG0_WRT_SHIFT) \
+				| (0 << TIMING_CFG0_RRT_SHIFT) \
+				| (0 << TIMING_CFG0_WWT_SHIFT) \
+				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+				/* 0x00220802 */
+#define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
+				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
+				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
+				| (6 << TIMING_CFG1_REFREC_SHIFT) \
+				| (2 << TIMING_CFG1_WRREC_SHIFT) \
+				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+				| (2 << TIMING_CFG1_WRTORD_SHIFT))
+				/* 0x27256222 */
+#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
+				| (4 << TIMING_CFG2_CPO_SHIFT) \
+				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
+				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
+				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
+				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
+				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
+				/* 0x121048c5 */
+#define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
+				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+				/* 0x03600100 */
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
+				| SDRAM_CFG_32_BE)
+				/* 0x43080000 */
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
+#define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
+				| (0x0232 << SDRAM_MODE_SD_SHIFT))
+				/* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CONFIG_SYS_DDR_MODE2		0x00000000
+
+/*
+ * Memory test
+ */
+#define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x07f00000
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE /* start of monitor */
+
+#define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR		0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		8 /* FLASH size is 8M */
+#define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */
+
+/* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016 /* 8MB window size */
+
+#define CONFIG_SYS_BR0_PRELIM	(\
+		CONFIG_SYS_FLASH_BASE	/* Flash Base address */	|\
+		(2 << BR_PS_SHIFT)	/* 16 bit port size */		|\
+		BR_V)			/* valid */
+#define CONFIG_SYS_OR0_PRELIM	((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+				| OR_UPM_XAM \
+				| OR_GPCM_CSNT \
+				| OR_GPCM_ACS_DIV2 \
+				| OR_GPCM_XACS \
+				| OR_GPCM_SCY_15 \
+				| OR_GPCM_TRLX \
+				| OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
+/* 127 64KB sectors and 8 8KB top sectors per device */
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
+
+/*
+ * NAND Flash on the Local Bus
+ */
+#define CONFIG_SYS_NAND_BASE		0xE0600000	/* 0xE0600000 */
+#define CONFIG_SYS_BR1_PRELIM	( CONFIG_SYS_NAND_BASE \
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8 bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V )		/* valid */
+#define CONFIG_SYS_OR1_PRELIM	( 0xFFFF8000		/* length 32K */ \
+				| OR_FCM_CSCT \
+				| OR_FCM_CST \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_1 \
+				| OR_FCM_TRLX \
+				| OR_FCM_EHTR )
+				/* 0xFFFF8396 */
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */
+
+#ifdef CONFIG_VSC7385_ENET
+#define CONFIG_TSEC2
+#define CONFIG_SYS_VSC7385_BASE		0xF0000000
+#define CONFIG_SYS_BR2_PRELIM		0xf0000801 /* VSC7385 Base address */
+#define CONFIG_SYS_OR2_PRELIM		0xfffe09ff /* VSC7385, 128K bytes*/
+/* Access window base at VSC7385 base */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_VSC7385_BASE
+/* Access window size 128K */
+#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+#endif
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/* I2C */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED	400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{{0x51}} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C2_OFFSET	0x3100
+
+
+/*
+ * Board info - revision and where boot from
+ */
+#define CONFIG_SYS_I2C_PCF8574A_ADDR	0x39
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1337	/* ds1339 on board, use ds1337 rtc via i2c */
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCIE1_BASE		0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
+
+/*
+ * Fake PCIE2 definitions: there is no PCIE2 on this board but the code
+ * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this
+ */
+#define CONFIG_SYS_PCIE2_BASE		0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
+
+#define CONFIG_PCI
+#define CONFIG_PCIE
+
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
+
+/*
+ * TSEC
+ */
+#define CONFIG_NET_MULTI
+#define CONFIG_TSEC_ENET	/* TSEC ethernet support */
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET	0x25000
+#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII		1 /* MII PHY management */
+#define CONFIG_TSEC1_NAME	"eTSEC0"
+#define CONFIG_TSEC2_NAME	"eTSEC1"
+#define TSEC1_PHY_ADDR		2
+#define TSEC2_PHY_ADDR		1
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME		"eTSEC0"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+				 CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
+				 HID0_ENABLE_INSTRUCTION_CACHE | \
+				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CONFIG_SYS_HID2		HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
+					BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+					BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
+					BATL_CACHEINHIBIT | \
+					BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
+					BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
+
+#define xstr(s)	str(s)
+#define str(s)	#s
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consoledev=ttyS0\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs}"				\
+		" console=${consoledev},${baudrate}\0"			\
+	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
+	"addmisc=setenv bootargs ${bootargs}\0"				\
+	"kernel_addr=FE080000\0"					\
+	"fdt_addr=FE280000\0"						\
+	"ramdisk_addr=FE290000\0"					\
+	"u-boot=mpc8308rdb/u-boot.bin\0"				\
+	"kernel_addr_r=1000000\0"					\
+	"fdt_addr_r=C00000\0"						\
+	"hostname=mpc8308rdb\0"						\
+	"bootfile=mpc8308rdb/uImage\0"					\
+	"fdtfile=mpc8308rdb/mpc8308rdb.dtb\0"				\
+	"rootpath=/opt/eldk-4.2/ppc_6xx\0"				\
+	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
+		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
+	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
+		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
+	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
+		"tftp ${fdt_addr_r} ${fdtfile};"			\
+		"run nfsargs addip addtty addmtd addmisc;"		\
+		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
+	"bootcmd=run flash_self\0"					\
+	"load=tftp ${loadaddr} ${u-boot}\0"				\
+	"update=protect off " xstr(CONFIG_SYS_MONITOR_BASE)		\
+		" +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE)	\
+		" +${filesize};cp.b ${fileaddr} "			\
+		xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"		\
+	"upd=run load update\0"						\
+
+#endif	/* __CONFIG_H */