rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 113 insertions, 113 deletions

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index b6508742254..fb4d172687b 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -72,23 +72,23 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-#define CFG_MEMTEST_START	0x00200000	/* memtest works on */
-#define CFG_MEMTEST_END		0x00400000
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
-#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
-#define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
-#define CFG_PCIE1_ADDR		(CFG_CCSRBAR+0xa000)
-#define CFG_PCIE2_ADDR		(CFG_CCSRBAR+0x9000)
-#define CFG_PCIE3_ADDR		(CFG_CCSRBAR+0xb000)
+#define CONFIG_SYS_PCI1_ADDR		(CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE1_ADDR		(CONFIG_SYS_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCIE2_ADDR		(CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE3_ADDR		(CONFIG_SYS_CCSRBAR+0xb000)
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -99,8 +99,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
 
-#define CFG_DDR_SDRAM_BASE	0x00000000
-#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_VERY_BIG_RAM
 
 #define CONFIG_NUM_DDR_CONTROLLERS	1
@@ -145,39 +145,39 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Local Bus Definitions
  */
-#define CFG_BOOT_BLOCK		0xfc000000	/* boot TLB */
+#define CONFIG_SYS_BOOT_BLOCK		0xfc000000	/* boot TLB */
 
-#define CFG_FLASH_BASE		0xff800000	/* start of FLASH 8M */
+#define CONFIG_SYS_FLASH_BASE		0xff800000	/* start of FLASH 8M */
 
-#define CFG_BR0_PRELIM		0xff801001
-#define CFG_BR1_PRELIM		0xfe801001
+#define CONFIG_SYS_BR0_PRELIM		0xff801001
+#define CONFIG_SYS_BR1_PRELIM		0xfe801001
 
-#define CFG_OR0_PRELIM		0xff806e65
-#define CFG_OR1_PRELIM		0xff806e65
+#define CONFIG_SYS_OR0_PRELIM		0xff806e65
+#define CONFIG_SYS_OR1_PRELIM		0xff806e65
 
-#define CFG_FLASH_BANKS_LIST	{CFG_FLASH_BASE}
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE}
 
-#define CFG_FLASH_QUIET_TEST
-#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
-#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
-#undef	CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
 
-#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
 
-#define CFG_LBC_NONCACHE_BASE	0xf8000000
+#define CONFIG_SYS_LBC_NONCACHE_BASE	0xf8000000
 
-#define CFG_BR2_PRELIM		0xf8201001	/* port size 16bit */
-#define CFG_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/
+#define CONFIG_SYS_BR2_PRELIM		0xf8201001	/* port size 16bit */
+#define CONFIG_SYS_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/
 
-#define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
-#define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
+#define CONFIG_SYS_BR3_PRELIM		0xf8100801	/* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
 
 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000	/* PIXIS registers */
@@ -197,7 +197,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
 #define PIXIS_VSPEED2		0x1d	/* VELA VSpeed 2 */
-#define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
+#define CONFIG_SYS_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
 #define PIXIS_VSPEED2_TSEC1SER	0x2
 #define PIXIS_VSPEED2_TSEC3SER	0x1
 #define PIXIS_VCFGEN1_TSEC1SER	0x20
@@ -206,17 +206,17 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK      1
-#define CFG_INIT_RAM_ADDR      0xf4010000      /* Initial L1 address */
-#define CFG_INIT_RAM_END       0x00004000      /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_LOCK      1
+#define CONFIG_SYS_INIT_RAM_ADDR      0xf4010000      /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_END       0x00004000      /* End of used area in RAM */
 
 
-#define CFG_GBL_DATA_SIZE	128	/* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
 
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
@@ -224,21 +224,21 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE	1
-#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE	\
+#define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
 /* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef	CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -246,72 +246,72 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
-#define CFG_64BIT_STRTOUL		1
-#define CFG_64BIT_VSPRINTF		1
+#define CONFIG_SYS_64BIT_STRTOUL		1
+#define CONFIG_SYS_64BIT_VSPRINTF		1
 
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR	0x57
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
-#define CFG_I2C_OFFSET		0x3100
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3100
 
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
-#define CFG_PCIE_PHYS		0x80000000	/* 1G PCIE TLB */
-#define CFG_PCI_PHYS		0xc0000000	/* 512M PCI TLB */
+#define CONFIG_SYS_PCIE_PHYS		0x80000000	/* 1G PCIE TLB */
+#define CONFIG_SYS_PCI_PHYS		0xc0000000	/* 512M PCI TLB */
 
-#define CFG_PCI1_MEM_BASE	0xc0000000
-#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CFG_PCI1_IO_BASE	0x00000000
-#define CFG_PCI1_IO_PHYS	0xe1000000
-#define CFG_PCI1_IO_SIZE	0x00010000	/* 64k */
+#define CONFIG_SYS_PCI1_MEM_BASE	0xc0000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00010000	/* 64k */
 
 /* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS	0x00000000
-#define CFG_PCI_MEMORY_PHYS	0x00000000
-#define CFG_PCI_MEMORY_SIZE	0x80000000
+#define CONFIG_SYS_PCI_MEMORY_BUS	0x00000000
+#define CONFIG_SYS_PCI_MEMORY_PHYS	0x00000000
+#define CONFIG_SYS_PCI_MEMORY_SIZE	0x80000000
 
 /* controller 2, Slot 1, tgtid 1, Base address 9000 */
-#define CFG_PCIE2_MEM_BASE	0x80000000
-#define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
-#define CFG_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CFG_PCIE2_IO_BASE	0x00000000
-#define CFG_PCIE2_IO_PHYS	0xe1010000
-#define CFG_PCIE2_IO_SIZE	0x00010000	/* 64k */
+#define CONFIG_SYS_PCIE2_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xe1010000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 1, Slot 2,tgtid 2, Base address a000 */
-#define CFG_PCIE1_MEM_BASE	0xa0000000
-#define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCIE1_IO_BASE	0x00000000
-#define CFG_PCIE1_IO_PHYS	0xe1020000
-#define CFG_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xe1020000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 3, direct to uli, tgtid 3, Base address b000 */
-#define CFG_PCIE3_MEM_BASE	0xb0000000
-#define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
-#define CFG_PCIE3_MEM_SIZE	0x00100000	/* 1M */
-#define CFG_PCIE3_IO_BASE	0x00000000
-#define CFG_PCIE3_IO_PHYS	0xb0100000	/* reuse mem LAW */
-#define CFG_PCIE3_IO_SIZE	0x00100000	/* 1M */
-#define CFG_PCIE3_MEM_BASE2	0xb0200000
-#define CFG_PCIE3_MEM_PHYS2	CFG_PCIE3_MEM_BASE2
-#define CFG_PCIE3_MEM_SIZE2	0x00200000	/* 1M */
+#define CONFIG_SYS_PCIE3_MEM_BASE	0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	CONFIG_SYS_PCIE3_MEM_BASE
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCIE3_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xb0100000	/* reuse mem LAW */
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCIE3_MEM_BASE2	0xb0200000
+#define CONFIG_SYS_PCIE3_MEM_PHYS2	CONFIG_SYS_PCIE3_MEM_BASE2
+#define CONFIG_SYS_PCIE3_MEM_SIZE2	0x00200000	/* 1M */
 
 #if defined(CONFIG_PCI)
 
 /*PCIE video card used*/
-#define VIDEO_IO_OFFSET		CFG_PCIE2_IO_PHYS
+#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE2_IO_PHYS
 
 /*PCI video card used*/
-/*#define VIDEO_IO_OFFSET	CFG_PCI1_IO_PHYS*/
+/*#define VIDEO_IO_OFFSET	CONFIG_SYS_PCI1_IO_PHYS*/
 
 /* video */
 #define CONFIG_VIDEO
@@ -324,7 +324,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_ATI_RADEON_FB
 #define CONFIG_VIDEO_LOGO
 /*#define CONFIG_CONSOLE_CURSOR*/
-#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
 #endif
 
 #define CONFIG_NET_MULTI
@@ -341,8 +341,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
 
 #ifndef CONFIG_PCI_PNP
-	#define PCI_ENET0_IOADDR	CFG_PCI1_IO_BASE
-	#define PCI_ENET0_MEMADDR	CFG_PCI1_IO_BASE
+	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCI1_IO_BASE
+	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI1_IO_BASE
 	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
 #endif
 
@@ -352,10 +352,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #ifdef CONFIG_SCSI_AHCI
 #define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID	4
-#define CFG_SCSI_MAX_LUN	1
-#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
+#define CONFIG_SYS_SCSI_MAX_LUN	1
+#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
 #endif /* SCSCI */
 
 #endif	/* CONFIG_PCI */
@@ -395,16 +395,16 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Environment
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
-#if CFG_MONITOR_BASE > 0xfff80000
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
 #define CONFIG_ENV_ADDR		0xfff80000
 #else
-#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE + 0x70000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x70000)
 #endif
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K (one sector) */
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 /*
  * BOOTP options
@@ -439,26 +439,26 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING		/* Command-line editing */
-#define CFG_LOAD_ADDR	0x2000000	/* default load address */
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args */
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions