powerpc: ppc4xx: remove p3p440 support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>

1 files changed, 0 insertions, 302 deletions

diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h
deleted file mode 100644
index eb1400337dc..00000000000
--- a/include/configs/p3p440.h
+++ /dev/null
@@ -1,302 +0,0 @@
-/*
- * (C) Copyright 2005-2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/************************************************************************
- * board/config_p3p440.h - configuration for Prodrive P3P440
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_P3P440		1	    /* Board is P3P440		*/
-#define CONFIG_440GP		1	    /* Specifc GP support	*/
-#define CONFIG_440		1	    /* ... PPC440 family	*/
-#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
-#define CONFIG_MISC_INIT_R	1	    /* Call misc_init_r		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
-
-#define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
-#define CONFIG_SYS_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CONFIG_SYS_MONITOR_BASE    0xfffc0000	    /* start of monitor		*/
-#define CONFIG_SYS_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
-#define CONFIG_SYS_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
-#define CONFIG_SYS_PCI_BASE	    0xd0000000	    /* internal PCI regs	*/
-
-#define CONFIG_SYS_USB_BASE	    (CONFIG_SYS_PERIPHERAL_BASE + 0x00000000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_ISRAM_BASE  /* Initial RAM address	*/
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2000	    /* Size of used area in RAM	*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon*/
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc*/
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SDRAM_BANK0	1	/* init onboard DDR SDRAM bank 0*/
-#define CONFIG_SDRAM_ECC		/* enable ECC support		*/
-#define CONFIG_SYS_SDRAM_TABLE	{ \
-		{(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
-		{(64 << 20),  12, 0x00082001}} /* 64MB mode 2, 12x9(4)	*/
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_SYS_BAUDRATE_TABLE						\
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,		\
-			57600, 115200, 230400, 460800, 921600 }
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-#define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} }	/* Don't probe these addrs */
-
-/*-----------------------------------------------------------------------
- * I2C RTC
- *----------------------------------------------------------------------*/
-#define CONFIG_RTC_MAX6900	1		/* MAX6900 RTC		*/
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (PCF8594C) for environment
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x54	/* EEPROM PCF8594C		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3	/* The Philips PCF8594C has	*/
-					/* 8 byte page write mode using */
-					/* last 3 bits of the address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	40   /* and takes up to 40 msec */
-
-/*-----------------------------------------------------------------------
- * Default configuration (environment varibles...)
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=p3p440\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/p3p440/uImage\0"				\
-	"kernel_addr=ff800000\0"					\
-	"ramdisk_addr=ff810000\0"					\
-	"load=tftp 100000 /tftpboot/p3p440/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"unlock=yes\0"							\
-	""
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0x1c	/* PHY address			*/
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR	0x1d	/* EMAC1 PHY address		*/
-#define CONFIG_SYS_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_SNTP
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *----------------------------------------------------------------------*/
-/* General PCI */
-#define CONFIG_PCI			            /* include pci support	        */
-#define	CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			        /* do pci plug-and-play         */
-#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
-#define CONFIG_SYS_PCI_TARGBASE    0x80000000  /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT	            /* let board init pci target    */
-
-#define CONFIG_DISABLE_PISE_TEST	/* disable PISE test (PCIX only)*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH0		0xFF800000
-#define CONFIG_SYS_FLASH1		0xFF000000
-#define CONFIG_SYS_FLASH2		0xFE800000
-#define CONFIG_SYS_FLASH3		0xFE000000
-#define CONFIG_SYS_USB			0xF0000000
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB0AP		0x03050200
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH0 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB1AP		0x03050200
-#define CONFIG_SYS_EBC_PB1CR		(CONFIG_SYS_FLASH1 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (Flash Bank 2, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB2AP		0x03050200
-#define CONFIG_SYS_EBC_PB2CR		(CONFIG_SYS_FLASH2 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 3 (Flash Bank 3, NOR-FLASH) initialization			*/
-#define CONFIG_SYS_EBC_PB3AP		0x03050200
-#define CONFIG_SYS_EBC_PB3CR		(CONFIG_SYS_FLASH3 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 7 (USB controller) initialization				*/
-#define CONFIG_SYS_EBC_PB7AP		0x02015000
-#define CONFIG_SYS_EBC_PB7CR		(CONFIG_SYS_USB | 0xFE000) /* BAS=0xF00,BS=128MB,BU=R/W,BW=16bit*/
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible	*/
-#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH3, CONFIG_SYS_FLASH2, CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware flash protection	*/
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
-
-#define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-
-#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-#endif	/* __CONFIG_H */