powerpc: debris: remove orphan board

This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)

Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>

1 files changed, 0 insertions, 443 deletions

diff --git a/include/configs/debris.h b/include/configs/debris.h
deleted file mode 100644
index 4631b8621a0..00000000000
--- a/include/configs/debris.h
+++ /dev/null
@@ -1,443 +0,0 @@
-/*
- * (C) Copyright 2001, 2002
- * Sangmoon Kim, Etin Systems, dogoil@etinsys.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-/* Environments */
-
-/* bootargs */
-#define CONFIG_BOOTARGS \
-	"console=ttyS0,9600 init=/linuxrc " \
-	"root=/dev/nfs rw nfsroot=192.168.0.1:" \
-	"/tftpboot/target " \
-	"ip=192.168.0.2:192.168.0.1:192.168.0.1:" \
-	"255.255.255.0:debris:eth0:none " \
-	"mtdparts=phys:12m(root),-(kernel)"
-
-/* bootcmd */
-#define CONFIG_BOOTCOMMAND \
-	"tftp 800000 pImage; " \
-	"setenv bootargs console=ttyS0,9600 init=/linuxrc " \
-	"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
-	"${netmask}:${hostname}:eth0:none " \
-	"mtdparts=phys:12m(root),-(kernel); " \
-	"bootm 800000"
-
-/* bootdelay */
-#define CONFIG_BOOTDELAY	5	/* autoboot 5s */
-
-/* baudrate */
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/
-
-/* loads_echo */
-#define CONFIG_LOADS_ECHO	0	/* echo off for serial download */
-
-/* ethaddr */
-#undef CONFIG_ETHADDR
-
-/* eth2addr */
-#undef CONFIG_ETH2ADDR
-
-/* eth3addr */
-#undef CONFIG_ETH3ADDR
-
-/* ipaddr */
-#define CONFIG_IPADDR	192.168.0.2
-
-/* serverip */
-#define CONFIG_SERVERIP	192.168.0.1
-
-/* autoload */
-#undef CONFIG_SYS_AUTOLOAD
-
-/* rootpath */
-#define CONFIG_ROOTPATH "/tftpboot/target"
-
-/* gatewayip */
-#define CONFIG_GATEWAYIP 192.168.0.1
-
-/* netmask */
-#define CONFIG_NETMASK 255.255.255.0
-
-/* hostname */
-#define CONFIG_HOSTNAME debris
-
-/* bootfile */
-#define CONFIG_BOOTFILE "pImage"
-
-/* loadaddr */
-#define CONFIG_LOADADDR 800000
-
-/* preboot */
-#undef CONFIG_PREBOOT
-
-/* clocks_in_mhz */
-#undef CONFIG_CLOCKS_IN_MHZ
-
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245		1
-#define CONFIG_DEBRIS		1
-
-#if 0
-#define USE_DINK32		1
-#else
-#undef USE_DINK32
-#endif
-
-#define CONFIG_CONS_INDEX       1
-#define CONFIG_BAUDRATE		9600
-#define CONFIG_DRAM_SPEED	100		/* MHz */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_KGDB
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_SDRAM
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI				/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP
-
-#define CONFIG_EEPRO100
-#define CONFIG_SYS_RX_ETH_BUFFER	8	/* use 8 rx buffer on eepro100  */
-#define CONFIG_EEPRO100_SROM_WRITE
-
-#define PCI_ENET0_IOADDR	0x80000000
-#define PCI_ENET0_MEMADDR	0x80000000
-#define	PCI_ENET1_IOADDR	0x81000000
-#define	PCI_ENET1_MEMADDR	0x81000000
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	0x20000000
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_SYS_RESET_ADDRESS	0xFFF00100
-
-#if defined (USE_DINK32)
-#define CONFIG_SYS_MONITOR_LEN		0x00040000
-#define CONFIG_SYS_MONITOR_BASE	0x00090000
-#define CONFIG_SYS_RAMBOOT		1
-#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_INIT_RAM_SIZE	0x10000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#undef	CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN		0x00040000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR     0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE      0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET  (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#endif
-
-#define CONFIG_SYS_FLASH_BASE		0x7C000000
-#define CONFIG_SYS_FLASH_SIZE		(16*1024*1024)	/* debris has tiny eeprom	*/
-
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x04000000	/* 0 ... 32 MB in DRAM		*/
-
-#define CONFIG_SYS_EUMB_ADDR		0xFC000000
-
-#define CONFIG_SYS_FLASH_RANGE_BASE	0xFF000000	/* flash memory address range	*/
-#define CONFIG_SYS_FLASH_RANGE_SIZE	0x01000000
-#define FLASH_BASE0_PRELIM	0x7C000000	/* debris flash		*/
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor0=debris-0"
-#define MTDPARTS_DEFAULT	"mtdparts=debris-0:-(jffs2)"
-*/
-
-#define CONFIG_ENV_IS_IN_NVRAM      1
-#define CONFIG_ENV_OVERWRITE     1
-#define CONFIG_SYS_NVRAM_ACCESS_ROUTINE 1
-#define CONFIG_ENV_ADDR		0xFF000000 /* right at the start of NVRAM  */
-#define CONFIG_ENV_SIZE		0x400	/* Size of the Environment - 8K	   */
-#define CONFIG_ENV_OFFSET		0	/* starting right at the beginning */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xff000000
-
-/*
- * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_VXWORKS_OFFS =
- * NV_RAM_ADDRS + NV_BOOT_OFFSET + NV_ENET_OFFSET
- */
-#define CONFIG_SYS_NVRAM_VXWORKS_OFFS	0x6900
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef  CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#error "Soft I2C is not configured properly.  Please review!"
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-#define I2C_PORT		3               /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE		(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
-#define I2C_READ		((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)		if(bit) iop->pdat |=  0x00010000; \
-				else    iop->pdat &= ~0x00010000
-#define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
-				else    iop->pdat &= ~0x00020000
-#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-#define CONFIG_SYS_FLASH_BANKS		{ FLASH_BASE0_PRELIM }
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#define CONFIG_SYS_NS16550_CLK		7372800
-
-#define CONFIG_SYS_NS16550_COM1	0xFF080000
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_NS16550_COM1 + 8)
-#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_NS16550_COM1 + 16)
-#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_NS16550_COM1 + 24)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3
-
-#define CONFIG_SYS_DLL_EXTEND		0x00
-#define CONFIG_SYS_PCI_HOLD_DEL	0x20
-
-#define CONFIG_SYS_ROMNAL	15	/* rom/flash next access time */
-#define CONFIG_SYS_ROMFAL	31	/* rom/flash access time */
-
-#define CONFIG_SYS_REFINT	430	/* # of clocks between CBR refresh cycles */
-
-#define CONFIG_SYS_DBUS_SIZE2	1	/* set for 8-bit RCS1, clear for 32,64 */
-
-/* the following are for SDRAM only*/
-#define CONFIG_SYS_BSTOPRE	121	/* Burst To Precharge, sets open page interval */
-#define CONFIG_SYS_REFREC	8	/* Refresh to activate interval		*/
-#define CONFIG_SYS_RDLAT	4	/* data latency from read command	*/
-#define CONFIG_SYS_PRETOACT	3	/* Precharge to activate interval	*/
-#define CONFIG_SYS_ACTTOPRE	5	/* Activate to Precharge interval	*/
-#define CONFIG_SYS_ACTORW		3	/* Activate to R/W			*/
-#define CONFIG_SYS_SDMODE_CAS_LAT	3	/* SDMODE CAS latency			*/
-#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE wrap type			*/
-#if 0
-#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* OBSOLETE!  SDMODE Burst length 2=4, 3=8		*/
-#endif
-
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-
-/* memory bank settings*/
-/*
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START		0x00000000
-#define CONFIG_SYS_BANK0_END		(0x4000000 - 1)
-#define CONFIG_SYS_BANK0_ENABLE	1
-#define CONFIG_SYS_BANK1_START		0x04000000
-#define CONFIG_SYS_BANK1_END		(0x8000000 - 1)
-#define CONFIG_SYS_BANK1_ENABLE	1
-#define CONFIG_SYS_BANK2_START		0x3ff00000
-#define CONFIG_SYS_BANK2_END		0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE	0
-#define CONFIG_SYS_BANK3_START		0x3ff00000
-#define CONFIG_SYS_BANK3_END		0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE	0
-#define CONFIG_SYS_BANK4_START		0x00000000
-#define CONFIG_SYS_BANK4_END		0x00000000
-#define CONFIG_SYS_BANK4_ENABLE	0
-#define CONFIG_SYS_BANK5_START		0x00000000
-#define CONFIG_SYS_BANK5_END		0x00000000
-#define CONFIG_SYS_BANK5_ENABLE	0
-#define CONFIG_SYS_BANK6_START		0x00000000
-#define CONFIG_SYS_BANK6_END		0x00000000
-#define CONFIG_SYS_BANK6_ENABLE	0
-#define CONFIG_SYS_BANK7_START		0x00000000
-#define CONFIG_SYS_BANK7_END		0x00000000
-#define CONFIG_SYS_BANK7_ENABLE	0
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE		0x01
-
-#define CONFIG_SYS_ODCR		0x75	/* configures line driver impedances,	*/
-					/* see 8240 book for bit definitions	*/
-#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
-					/* currently accessed page in memory	*/
-					/* see 8240 book for details		*/
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#if defined(USE_DINK32)
-#define CONFIG_SYS_IBAT1L	(0x40000000 | BATL_PP_00 )
-#define CONFIG_SYS_IBAT1U	(0x40000000 | BATU_BL_128K )
-#else
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#endif
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-
-#define CONFIG_DRAM_50MHZ	1
-#define CONFIG_SDRAM_50MHZ
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-#endif	/* __CONFIG_H */