summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rwxr-xr-xMAKEALL1
-rw-r--r--Makefile1
-rw-r--r--board/tqm8xx/tqm8xx.c47
-rw-r--r--include/configs/TK885D.h513
4 files changed, 562 insertions, 0 deletions
diff --git a/MAKEALL b/MAKEALL
index 6013d49f523..cb1322d7c93 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -135,6 +135,7 @@ LIST_8xx=" \
SPD823TS \
svm_sc8xx \
SXNI855T \
+ TK885D \
TOP860 \
TQM823L \
TQM823L_LCD \
diff --git a/Makefile b/Makefile
index 47206fc7602..fa12ed7cef8 100644
--- a/Makefile
+++ b/Makefile
@@ -1062,6 +1062,7 @@ TQM860M_config \
TQM862M_config \
TQM866M_config \
TQM885D_config \
+TK885D_config \
virtlab2_config: unconfig
@mkdir -p $(obj)include
@ >$(obj)include/config.h
diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c
index fcd941e0d2d..18bf2a83029 100644
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -504,4 +504,51 @@ int misc_init_r (void)
}
#endif /* CONFIG_NSCU */
+/* ---------------------------------------------------------------------------- */
+/* TK885D specific initializaion */
+/* ---------------------------------------------------------------------------- */
+#ifdef CONFIG_TK885D
+#include <miiphy.h>
+int last_stage_init(void)
+{
+ const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY};
+ unsigned short reg;
+ int ret, i = 100;
+ char *s;
+
+ mii_init();
+ /* Without this delay 0xff is read from the UART buffer later in
+ * abortboot() and autoboot is aborted */
+ udelay(10000);
+ while (tstc() && i--)
+ (void)getc();
+
+ /* Check if auto-negotiation is prohibited */
+ s = getenv("phy_auto_nego");
+
+ if (!s || !strcmp(s, "on"))
+ /* Nothing to do - autonegotiation by default */
+ return 0;
+
+ for (i = 0; i < 2; i++) {
+ ret = miiphy_read("FEC ETHERNET", phy[i], PHY_BMCR, &reg);
+ if (ret) {
+ printf("Cannot read BMCR on PHY %d\n", phy[i]);
+ return 0;
+ }
+ /* Auto-negotiation off, hard set full duplex, 100Mbps */
+ ret = miiphy_write("FEC ETHERNET", phy[i],
+ PHY_BMCR, (reg | PHY_BMCR_100MB |
+ PHY_BMCR_DPLX) & ~PHY_BMCR_AUTON);
+ if (ret) {
+ printf("Cannot write BMCR on PHY %d\n", phy[i]);
+ return 0;
+ }
+ }
+
+ return 0;
+}
+
+#endif
+
/* ------------------------------------------------------------------------- */
diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h
new file mode 100644
index 00000000000..761a35276bb
--- /dev/null
+++ b/include/configs/TK885D.h
@@ -0,0 +1,513 @@
+/*
+ * (C) Copyright 2000-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2006
+ * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC885 1 /* This is a MPC885 CPU */
+#define CONFIG_TQM885D 1 /* ...on a TQM88D module */
+#define CONFIG_TK885D 1 /* ...in a TK885D base board */
+
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
+#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
+#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
+#define CONFIG_8xx_CPUCLK_DEFAULT 66000000 /* 66 MHz - CPU default clock */
+ /* (it will be used if there is no */
+ /* 'cpuclk' variable with valid value) */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_BOARD_TYPES 1 /* support board types */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk/ppc_8xx\0" \
+ "bootfile=/tftpboot/TQM885D/uImage\0" \
+ "kernel_addr=40080000\0" \
+ "ramdisk_addr=40180000\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "update=protect off 40000000 +${filesize};" \
+ "erase 40000000 +${filesize};" \
+ "cp.b 200000 40000000 ${filesize};" \
+ "protect on 40000000 +${filesize}\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+
+#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
+#define CFG_I2C_SLAVE 0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
+#endif /* CONFIG_SOFT_I2C */
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+# define CONFIG_RTC_DS1337 1
+# define CFG_I2C_RTC_ADDR 0x68
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#undef CONFIG_RTC_MPC8xx /* MPC885 does not support RTC */
+
+#define CONFIG_TIMESTAMP /* but print image timestmps */
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0300000 /* 1 ... 3 MB in DRAM */
+#define CFG_ALT_MEMTEST /* alternate, more extensive
+ memory test.*/
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Enable loopw command.
+ */
+#define CONFIG_LOOPW
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+
+/* use CFI flash driver */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment */
+#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else /* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif /* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/*
+ * FLASH timing: Default value of OR0 after reset
+ */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
+ OR_SCY_6_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
+#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM 0x00000A00
+
+#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_OR3_PRELIM CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
+#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
+#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
+ BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif /* CONFIG_CAN_DRIVER */
+
+/*
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ */
+#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+
+/*
+ * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
+ *
+ * CPUclock(MHz) * 31.2
+ * CFG_MAMR_PTA = ----------------------------------- with DFBRG = 0
+ * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
+ *
+ * CPU clock = 15 MHz: CFG_MAMR_PTA = 29 -> 4 * 7.73 us
+ * CPU clock = 50 MHz: CFG_MAMR_PTA = 97 -> 4 * 7.76 us
+ * CPU clock = 66 MHz: CFG_MAMR_PTA = 128 -> 4 * 7.75 us
+ * CPU clock = 133 MHz: CFG_MAMR_PTA = 255 -> 4 * 7.67 us
+ *
+ * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
+ * be met also in the default configuration, i.e. if environment variable
+ * 'cpuclk' is not set.
+ */
+#define CFG_MAMR_PTA 128
+
+/*
+ * Memory Periodic Timer Prescaler Register (MPTPR) values.
+ */
+/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16
+/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Network configuration
+ */
+#define CONFIG_FEC_ENET /* enable ethernet on FEC */
+#define CONFIG_ETHER_ON_FEC1 /* ... for FEC1 */
+#define CONFIG_ETHER_ON_FEC2 /* ... for FEC2 */
+
+#define CONFIG_LAST_STAGE_INIT 1 /* Have to configure PHYs for Linux */
+
+/* CFG_DISCOVER_PHY only works with FEC if only one interface is enabled */
+#if (!defined(CONFIG_ETHER_ON_FEC1) || !defined(CONFIG_ETHER_ON_FEC2))
+#define CFG_DISCOVER_PHY
+#endif
+
+#ifndef CFG_DISCOVER_PHY
+/* PHY addresses - hard wired in hardware */
+#define CONFIG_FEC1_PHY 1
+#define CONFIG_FEC2_PHY 2
+#endif
+
+#define CONFIG_NET_RETRY_COUNT 3
+#define CONFIG_ETHPRIME "FEC ETHERNET"
+
+#endif /* __CONFIG_H */