summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--MAINTAINERS2
-rw-r--r--board/sbc8560/Makefile50
-rw-r--r--board/sbc8560/README57
-rw-r--r--board/sbc8560/ddr.c43
-rw-r--r--board/sbc8560/law.c60
-rw-r--r--board/sbc8560/sbc8560.c369
-rw-r--r--board/sbc8560/tlb.c65
-rw-r--r--boards.cfg6
-rw-r--r--include/configs/SBC8540.h428
-rw-r--r--include/configs/sbc8560.h459
10 files changed, 0 insertions, 1539 deletions
diff --git a/MAINTAINERS b/MAINTAINERS
index 971235bbca3..ff8e47caac8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -214,9 +214,7 @@ Siddarth Gore <gores@marvell.com>
Paul Gortmaker <paul.gortmaker@windriver.com>
sbc8349 MPC8349
- sbc8540 MPC8540
sbc8548 MPC8548
- sbc8560 MPC8560
sbc8641d MPC8641D
Frank Gottschling <fgottschling@eltec.de>
diff --git a/board/sbc8560/Makefile b/board/sbc8560/Makefile
deleted file mode 100644
index ce0156040ae..00000000000
--- a/board/sbc8560/Makefile
+++ /dev/null
@@ -1,50 +0,0 @@
-#
-# (C) Copyright 2004-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
-# Added support for Wind River SBC8560 board
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS-y += $(BOARD).o
-COBJS-y += law.o
-COBJS-y += tlb.o
-COBJS-$(CONFIG_FSL_DDR1) += ddr.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS-y))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/sbc8560/README b/board/sbc8560/README
deleted file mode 100644
index c4b642236e9..00000000000
--- a/board/sbc8560/README
+++ /dev/null
@@ -1,57 +0,0 @@
-The port was tested on Wind River System Sbc8560 board
-<www.windriver.com>. U-Boot was installed on the flash memory of the
-CPU card (no the SODIMM).
-
-NOTE: Please configure uboot compile to the proper PCI frequency and
-setup the appropriate DIP switch settings.
-
-SBC8560 board:
-
-Make sure boards switches are set to their appropriate conditions.
-Refer to the Engineering Reference Guide ERG-00300-002. Of particular
-importance are: 1) the settings for JP4 (JP4 1-3 and 2-4), which
-select the on-board FLASH device (Intel 28F128Jx); 2) The settings
-for the Clock SW9 (33 MHz or 66 MHz).
-
- Note: SW9 Settings: 66 MHz
- 4:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - off, pos4 - on, pos5 - off, pos6 - on
- Note: SW9 Settings: 33 MHz
- 8:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - on, pos4 - off, pos5 - off, pos6 - on
-
-
-Flashing the FLASH device with the "Wind River ICE":
-
-1) Properly connect and configure the Wind River ICE to the target
- JTAG port. This includes running the SBC8560 register script. Make
- sure target memory can be read and written.
-
-2) Build the u-boot image:
- make distclean
- make SBC8560_66_config or SBC8560_33_config
- make CROSS_COMPILE=.../ELDK3.0/ppc_8xx-/ all
-
- Note: reference is made to the ELDK3.0 compiler. Further, it seems
- the ppc_8xx compiler is required for the 85xx (no 85xx
- designated compiler in ELDK3.0)
-
-3) Convert the uboot (.elf) file to a uboot.bin file (using
- visionClick converter). The bin file should be converted from
- fffc0000 to ffffffff
-
-4) Setup the Flash Utility (tools menu) for:
-
- Do a "dc clr" [visionClick] to load the default register settings
- Determine the clock speed of the PCI bus and set SW9 accordingly
- Note: the speed of the PCI bus defaults to the slowest PCI card
- PlayBack the "default" register file for the SBC8560
- Select the uboot.bin file with zero bias
- Select the initialize Target prior to programming
- Select the V28F640Jx (8192 x 8) 1 device FLASH Algorithm
- Select the erase base address from FFFC0000 to FFFFFFFF
- Select the start address from 0 with size of 4000
-
-5) Erase and Program
diff --git a/board/sbc8560/ddr.c b/board/sbc8560/ddr.c
deleted file mode 100644
index e9babc6477e..00000000000
--- a/board/sbc8560/ddr.c
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * Version 2 as published by the Free Software Foundation.
- */
-
-#include <common.h>
-
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
- */
- popts->cpo_override = 0;
-
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
- */
- popts->write_data_delay = 3;
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
diff --git a/board/sbc8560/law.c b/board/sbc8560/law.c
deleted file mode 100644
index 4e6baed2f4d..00000000000
--- a/board/sbc8560/law.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/* LAW(Local Access Window) configuration:
- * 0000_0000-0800_0000: DDR(512M) -or- larger
- * c000_0000-cfff_ffff: PCI(256M)
- * d000_0000-dfff_ffff: RapidIO(256M)
- * e000_0000-ffff_ffff: localbus(512M)
- * e000_0000-e3ff_ffff: LBC 64M, 32-bit flash on CS6
- * e400_0000-e7ff_ffff: LBC 64M, 32-bit flash on CS1
- * e800_0000-efff_ffff: LBC 128M, nothing here
- * f000_0000-f3ff_ffff: LBC 64M, SDRAM on CS3
- * f400_0000-f7ff_ffff: LBC 64M, SDRAM on CS4
- * f800_0000-fdff_ffff: LBC 64M, nothing here
- * fc00_0000-fcff_ffff: LBC 16M, CSR,RTC,UART,etc on CS5
- * fd00_0000-fdff_ffff: LBC 16M, nothing here
- * fe00_0000-feff_ffff: LBC 16M, nothing here
- * ff00_0000-ff6f_ffff: LBC 7M, nothing here
- * ff70_0000-ff7f_ffff: CCSRBAR 1M
- * ff80_0000-ffff_ffff: LBC 8M, 8-bit flash on CS0
- * Note: CCSRBAR and L2-as-SRAM don't need configure Local Access
- * Window.
- * Note: If flash is 8M at default position(last 8M),no LAW needed.
- */
-
-struct law_entry law_table[] = {
-#ifndef CONFIG_SPD_EEPROM
- SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR),
-#endif
- SET_LAW(CONFIG_SYS_PCI_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCI),
- SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/sbc8560/sbc8560.c b/board/sbc8560/sbc8560.c
deleted file mode 100644
index 98bc7df4c8a..00000000000
--- a/board/sbc8560/sbc8560.c
+++ /dev/null
@@ -1,369 +0,0 @@
-/*
- * (C) Copyright 2003,Motorola Inc.
- * Xianghua Xiao, (X.Xiao@motorola.com)
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
- * Added support for Wind River SBC8560 board
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <ioports.h>
-#include <spd_sdram.h>
-#include <miiphy.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
- /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
- /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
- /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
- /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
- /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
- /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
- /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
- /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
- /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
- /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
- /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
- /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
- /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
- /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
- /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
- /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
- /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
- /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
- /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
- },
-
- /* Port B configuration */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
- /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
- /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
- /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
- /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
- /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
- /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
- /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
- /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
- /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
- /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
- /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
- /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
- /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
- /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
- /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */
- /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */
- /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
- /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
- /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
- /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
- /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 RTS */
- /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RxD */
- /* PD27 */ { 1, 1, 1, 1, 0, 0 }, /* SCC2 TxD */
- /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 RTS */
- /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
- /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
- /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- }
-};
-
-int board_early_init_f (void)
-{
-#if defined(CONFIG_PCI)
- volatile ccsr_pcix_t *pci = (void *)(CONFIG_SYS_MPC85xx_PCIX_ADDR);
-
- pci->peer &= 0xfffffffdf; /* disable master abort */
-#endif
- return 0;
-}
-
-void reset_phy (void)
-{
-#if defined(CONFIG_ETHER_ON_FCC) /* avoid compile warnings for now */
- volatile unsigned char *bcsr = (unsigned char *) CONFIG_SYS_BCSR;
-#endif
- /* reset Giga bit Ethernet port if needed here */
-
- /* reset the CPM FEC port */
-#if (CONFIG_ETHER_INDEX == 2)
- bcsr[0] &= ~0x20;
- udelay(2);
- bcsr[0] |= 0x20;
- udelay(1000);
-#elif (CONFIG_ETHER_INDEX == 3)
- bcsr[0] &= ~0x10;
- udelay(2);
- bcsr[0] |= 0x10;
- udelay(1000);
-#endif
-#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
- /* reset PHY */
- miiphy_reset("FCC1", 0x0);
-
- /* change PHY address to 0x02 */
- bb_miiphy_write(NULL, 0, MII_MIPSCR, 0xf028);
-
- bb_miiphy_write(NULL, 0x02, MII_BMCR,
- BMCR_ANENABLE | BMCR_ANRESTART);
-#endif /* CONFIG_MII */
-}
-
-int checkboard (void)
-{
- sys_info_t sysinfo;
- char buf[32];
-
- get_sys_info (&sysinfo);
-
-#ifdef CONFIG_SBC8560
- printf ("Board: Wind River SBC8560 Board\n");
-#else
- printf ("Board: Wind River SBC8540 Board\n");
-#endif
- printf ("\tCPU: %s MHz\n", strmhz(buf, sysinfo.freqProcessor[0]));
- printf ("\tCCB: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus));
- printf ("\tDDR: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus/2));
- if((CONFIG_SYS_LBC_LCRR & 0x0f) == 2 || (CONFIG_SYS_LBC_LCRR & 0x0f) == 4 \
- || (CONFIG_SYS_LBC_LCRR & 0x0f) == 8) {
- printf ("\tLBC: %s MHz\n",
- strmhz(buf, sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & 0x0f)));
- } else {
- printf("\tLBC: unknown\n");
- }
- printf("\tCPM: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus));
- printf("L1 D-cache 32KB, L1 I-cache 32KB enabled.\n");
- return (0);
-}
-
-
-#if defined(CONFIG_SYS_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
- uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
- uint *p;
-
- printf("SDRAM test phase 1:\n");
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf("SDRAM test phase 2:\n");
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf("SDRAM test passed.\n");
- return 0;
-}
-#endif
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-phys_size_t fixed_sdram(void)
-{
-
-#define CONFIG_SYS_DDR_CONTROL 0xc2000000
-
- #ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
-
-#if (CONFIG_SYS_SDRAM_SIZE == 512)
- ddr->cs0_bnds = 0x0000000f;
-#else
- ddr->cs0_bnds = 0x00000007;
-#endif
- ddr->cs1_bnds = 0x0010001f;
- ddr->cs2_bnds = 0x00000000;
- ddr->cs3_bnds = 0x00000000;
- ddr->cs0_config = 0x80000102;
- ddr->cs1_config = 0x80000102;
- ddr->cs2_config = 0x00000000;
- ddr->cs3_config = 0x00000000;
- ddr->timing_cfg_1 = 0x37334321;
- ddr->timing_cfg_2 = 0x00000800;
- ddr->sdram_cfg = 0x42000000;
- ddr->sdram_mode = 0x00000022;
- ddr->sdram_interval = 0x05200100;
- ddr->err_sbe = 0x00ff0000;
- #if defined (CONFIG_DDR_ECC)
- ddr->err_disable = 0x0000000D;
- #endif
- asm("sync;isync;msync");
- udelay(500);
- #if defined (CONFIG_DDR_ECC)
- /* Enable ECC checking */
- ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
- #else
- ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
- #endif
- asm("sync; isync; msync");
- udelay(500);
- #endif
- return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-}
-#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void
-ft_board_setup(void *blob, bd_t *bd)
-{
- int node;
-#ifdef CONFIG_PCI
- const char *path;
-#endif
-
- ft_cpu_setup(blob, bd);
-
- node = fdt_path_offset(blob, "/aliases");
- if (node >= 0) {
-#ifdef CONFIG_PCI
- path = fdt_getprop(blob, node, "pci0", NULL);
- if (path) {
- tmp[1] = hose.last_busno - hose.first_busno;
- do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
- }
-#endif
- }
-}
-#endif
diff --git a/board/sbc8560/tlb.c b/board/sbc8560/tlb.c
deleted file mode 100644
index fe0ac763af2..00000000000
--- a/board/sbc8560/tlb.c
+++ /dev/null
@@ -1,65 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-/* TLB for CCSRBAR (IMMR) */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
-/* TLB for Local Bus stuff, just map the whole 512M */
-/* note that the LBC SDRAM is cache-inhibit and guarded, like everything else */
-
- SET_TLB_ENTRY(1, 0xe0000000, 0xe0000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
- SET_TLB_ENTRY(1, 0xf0000000, 0xf0000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_256M, 1),
-
-#if !defined(CONFIG_SPD_EEPROM)
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-#endif
-
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 6, BOOKE_PAGESZ_16K, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI_MEM_PHYS, CONFIG_SYS_PCI_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_256M, 1),
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index a5af63c1ba3..df62251253a 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -682,17 +682,11 @@ suvd3 powerpc mpc83xx km83xx keymile
tuge1 powerpc mpc83xx km83xx keymile - tuxx1:KM_DISABLE_APP2,TUGE1
tuxx1 powerpc mpc83xx km83xx keymile
kmsupx5 powerpc mpc83xx km83xx keymile - tuxx1:KM_DISABLE_APP2,KMSUPX5
-sbc8540 powerpc mpc85xx sbc8560 - - SBC8540
-sbc8540_33 powerpc mpc85xx sbc8560 - - SBC8540
-sbc8540_66 powerpc mpc85xx sbc8560 - - SBC8540
sbc8548 powerpc mpc85xx sbc8548 - - sbc8548
sbc8548_PCI_33 powerpc mpc85xx sbc8548 - - sbc8548:PCI,33
sbc8548_PCI_33_PCIE powerpc mpc85xx sbc8548 - - sbc8548:PCI,33,PCIE
sbc8548_PCI_66 powerpc mpc85xx sbc8548 - - sbc8548:PCI,66
sbc8548_PCI_66_PCIE powerpc mpc85xx sbc8548 - - sbc8548:PCI,66,PCIE
-sbc8560 powerpc mpc85xx sbc8560 - - sbc8560
-sbc8560_33 powerpc mpc85xx sbc8560 - - sbc8560
-sbc8560_66 powerpc mpc85xx sbc8560 - - sbc8560
socrates powerpc mpc85xx socrates
HWW1U1A powerpc mpc85xx hww1u1a exmeritus
MPC8536DS powerpc mpc85xx mpc8536ds freescale - MPC8536DS
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
deleted file mode 100644
index d448bf66503..00000000000
--- a/include/configs/SBC8540.h
+++ /dev/null
@@ -1,428 +0,0 @@
-/*
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
- * Added support for Wind River SBC8540 board
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * sbc8540 board configuration file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Top level Makefile configuration choices
- */
-#ifdef CONFIG_66
-#define CONFIG_PCI_66
-#endif
-
-#define TSEC_DEBUG
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-
-#define CONFIG_SYS_TEXT_BASE 0xfffc0000
-
-
-#define CONFIG_CPM2 1 /* has CPM2 */
-
-#define CONFIG_SBC8540 1 /* configuration for SBC8560 board */
-#define CONFIG_MPC8540 1
-
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */
-
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_PCI /* pci ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
-
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-
-#define CONFIG_ENV_OVERWRITE
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
-
-#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */
- #define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */
-#else
- #define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
-#endif
-
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
-
-#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
-
-/* DDR Setup */
-#define CONFIG_FSL_DDR1
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_SPD
-
-#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
-#endif
-
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
- #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
- #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */
- #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
-#else /* Boot from real Flash */
- #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
- #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
- #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */
- #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
-#endif
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/* local bus definitions */
-#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
-#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7
-
-#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */
-#define CONFIG_SYS_OR2_PRELIM 0x00000000
-
-#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
-#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
-#else
- #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
-#endif
-#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1
-
-#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
-#if 1
- #define CONFIG_SYS_OR5_PRELIM 0xff000ff7
-#else
- #define CONFIG_SYS_OR5_PRELIM 0xff0000f0
-#endif
-
-#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
-#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7
-#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-#define CONFIG_SYS_LBC_LSRT 0x20000000
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723
-#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723
-#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723
-
-/* just hijack the MOT BCSR def for SBC8560 misc devices */
-#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000)
-/* the size of CS5 needs to be >= 16M for TLB and LAW setups */
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#if 0
-#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */
-#else
-#define CONFIG_SYS_NS16550_CLK 264000000 /* get_bus_freq(0) */
-#endif
-
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#if 0
-#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000)
-#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000)
-#else
-/* SBC8540 uses internal COMM controller */
-#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004500)
-#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004600)
-#endif
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * I2C
- */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-
-#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
-
-#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-
-# define CONFIG_MPC85xx_TSEC1
-# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
-# define CONFIG_MII 1 /* MII PHY management */
-# define TSEC1_PHY_ADDR 25
-# define TSEC1_PHYIDX 0
-/* Options are: TSEC0 */
-# define CONFIG_ETHPRIME "TSEC0"
-
-
-#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-
- #undef CONFIG_ETHER_NONE /* define if ether on something else */
- #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */
- #define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-
- #if (CONFIG_ETHER_INDEX == 2)
- /*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers
- * - Full duplex
- */
- #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CONFIG_SYS_CPMFCR_RAMTYPE 0
- #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
-
- #elif (CONFIG_ETHER_INDEX == 3)
- /* need more definitions here for FE3 */
- #endif /* CONFIG_ETHER_INDEX */
-
- #define CONFIG_MII /* MII PHY management */
- #define CONFIG_BITBANGMII /* bit-bang MII PHY management */
- /*
- * GPIO pins used for bit-banged MII communications
- */
- #define MDIO_PORT 2 /* Port C */
- #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
- #define MDC_DECLARE MDIO_DECLARE
-
- #define MDIO_ACTIVE (iop->pdir |= 0x00400000)
- #define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
- #define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
- #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
- #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
- #define MIIDELAY udelay(1)
-
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#if 0
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */
-#endif
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if 0
-/* XXX This doesn't work and I don't want to fix it */
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
- #define CONFIG_SYS_RAMBOOT
-#else
- #undef CONFIG_SYS_RAMBOOT
-#endif
-#endif
-
-/* Environment */
-#if !defined(CONFIG_SYS_RAMBOOT)
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_ENV_IS_NOWHERE
- #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000)
- #define CONFIG_ENV_SIZE 0x2000
- #else
- #define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
- #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */
- #endif
-#else
- #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
- #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000"
-#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_CMD_MII
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "SBC8540=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*Note: change below for your network setting!!! */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-# define CONFIG_ETHADDR 00:vv:ww:xx:yy:8a
-# define CONFIG_HAS_ETH1
-# define CONFIG_ETH1ADDR 00:vv:ww:xx:yy:8b
-# define CONFIG_HAS_ETH2
-# define CONFIG_ETH2ADDR 00:vv:ww:xx:yy:8c
-#endif
-
-#define CONFIG_SERVERIP YourServerIP
-#define CONFIG_IPADDR YourTargetIP
-#define CONFIG_GATEWAYIP YourGatewayIP
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_HOSTNAME SBC8560
-#define CONFIG_ROOTPATH "YourRootPath"
-#define CONFIG_BOOTFILE "YourImageName"
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
deleted file mode 100644
index 46d60985d32..00000000000
--- a/include/configs/sbc8560.h
+++ /dev/null
@@ -1,459 +0,0 @@
-/*
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
- * Added support for Wind River SBC8560 board
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * sbc8560 board configuration file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Top level Makefile configuration choices
- */
-#ifdef CONFIG_66
-#define CONFIG_PCI_66
-#endif
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-
-#define CONFIG_SYS_TEXT_BASE 0xfffc0000
-
-
-#define CONFIG_CPM2 1 /* has CPM2 */
-#define CONFIG_SBC8560 1 /* configuration for SBC8560 board */
-#define CONFIG_MPC8560 1
-
-/* XXX flagging this as something I might want to delete */
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
-
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_PCI /* pci ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
-
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-
-#define CONFIG_ENV_OVERWRITE
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
-
-#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */
- #define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
-#else
- #define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
-#endif
-
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
-
-#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
-
-/* DDR Setup */
-#define CONFIG_FSL_DDR1
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_SPD
-
-#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
-#endif
-
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
- #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
- #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */
- #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
-#else /* Boot from real Flash */
- #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
- #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
- #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */
- #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
-#endif
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/* local bus definitions */
-#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
-#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7
-
-#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */
-#define CONFIG_SYS_OR2_PRELIM 0x00000000
-
-#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
-#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
-#else
- #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
-#endif
-#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1
-
-#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
-#if 1
- #define CONFIG_SYS_OR5_PRELIM 0xff000ff7
-#else
- #define CONFIG_SYS_OR5_PRELIM 0xff0000f0
-#endif
-
-#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
-#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7
-#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-#define CONFIG_SYS_LBC_LSRT 0x20000000
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723
-#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723
-#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723
-#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723
-
-/* just hijack the MOT BCSR def for SBC8560 misc devices */
-#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000)
-/* the size of CS5 needs to be >= 16M for TLB and LAW setups */
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000)
-#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/*
- * I2C
- */
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-
-#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000
-#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000
-#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
-
-#ifdef CONFIG_TSEC_ENET
-
-#ifndef CONFIG_MII
-#define CONFIG_MII 1 /* MII PHY management */
-#endif
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0x19
-#define TSEC2_PHY_ADDR 0x1a
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-
- #undef CONFIG_ETHER_NONE /* define if ether on something else */
- #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */
- #define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-
- #if (CONFIG_ETHER_INDEX == 2)
- /*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers
- * - Full duplex
- */
- #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CONFIG_SYS_CPMFCR_RAMTYPE 0
- #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
-
- #elif (CONFIG_ETHER_INDEX == 3)
- /* need more definitions here for FE3 */
- #endif /* CONFIG_ETHER_INDEX */
-
- #define CONFIG_MII /* MII PHY management */
- #define CONFIG_BITBANGMII /* bit-bang MII PHY management */
- /*
- * GPIO pins used for bit-banged MII communications
- */
- #define MDIO_PORT 2 /* Port C */
- #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
- #define MDC_DECLARE MDIO_DECLARE
-
- #define MDIO_ACTIVE (iop->pdir |= 0x00400000)
- #define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
- #define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
- #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
- #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
- #define MIIDELAY udelay(1)
-
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#if 0
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */
-#endif
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if 0
-/* XXX This doesn't work and I don't want to fix it */
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
- #define CONFIG_SYS_RAMBOOT
-#else
- #undef CONFIG_SYS_RAMBOOT
-#endif
-#endif
-
-/* Environment */
-#if !defined(CONFIG_SYS_RAMBOOT)
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CONFIG_ENV_IS_NOWHERE
- #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000)
- #define CONFIG_ENV_SIZE 0x2000
- #else
- #define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
- #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */
- #endif
-#else
- #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
- #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_CMD_MII
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "SBC8560=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-/* You can compile in a MAC address and your custom net settings by using
- * the following syntax. Your board should be marked with the assigned
- * MAC addresses directly on it.
- *
- * #define CONFIG_ETHADDR de:ad:be:ef:00:00
- * #define CONFIG_ETH1ADDR fa:ke:ad:dr:es:s!
- * #define CONFIG_SERVERIP <server ip>
- * #define CONFIG_IPADDR <board ip>
- * #define CONFIG_GATEWAYIP <gateway ip>
- * #define CONFIG_NETMASK <your netmask>
- */
-
-#define CONFIG_HOSTNAME SBC8560
-#define CONFIG_ROOTPATH "/home/ppc"
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=sbc8560.dtb\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-10 00:18:29 +0000