diff options
| -rw-r--r-- | arch/arm/dts/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/dts/zynqmp-sc-revB.dts | 430 |
2 files changed, 431 insertions, 0 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index fbce328acaf..29c40d1c3b6 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -411,6 +411,7 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ zynqmp-mini-emmc1.dtb \ zynqmp-mini-nand.dtb \ zynqmp-mini-qspi.dtb \ + zynqmp-sc-revB.dtb \ zynqmp-sm-k24-revA.dtb \ zynqmp-smk-k24-revA.dtb \ zynqmp-sm-k26-revA.dtb \ diff --git a/arch/arm/dts/zynqmp-sc-revB.dts b/arch/arm/dts/zynqmp-sc-revB.dts new file mode 100644 index 00000000000..e0b554c9c54 --- /dev/null +++ b/arch/arm/dts/zynqmp-sc-revB.dts @@ -0,0 +1,430 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Xilinx ZynqMP Generic System Controller + * + * (C) Copyright 2021 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. + * + * Michal Simek <michal.simek@amd.com> + */ +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/net/ti-dp83867.h> +#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> +#include <dt-bindings/phy/phy.h> + +/ { + model = "ZynqMP Generic System Controller"; + compatible = "xlnx,zynqmp-sc-revB", "xlnx,zynqmp-sc", "xlnx,zynqmp"; + + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + nvmem0 = &eeprom; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + spi0 = &qspi; + spi1 = &spi0; + spi2 = &spi1; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial1:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + fwuen { + label = "sw16"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + wakeup-source; + autorepeat; + }; + }; + + leds { + compatible = "gpio-leds"; + ds40-led { + label = "heartbeat"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + ds44-led { + label = "status"; + gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + }; + }; + + si5332_2: si5332_2 { /* u42 */ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + pwm-fan { + compatible = "pwm-fan"; + status = "okay"; + pwms = <&ttc0 2 40000 1>; + }; +}; + +&gpio { + status = "okay"; + gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */ + "QSPI_CS_B", "", "LED1", "LED2", "", /* 5 - 9 */ + "", "ZU4_TRIGGER", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */ + "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */ + "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "I2C1_SCL", /* 20 - 24 */ + "I2C1_SDA", "UART0_RXD", "UART0_TXD", "", "", /* 25 - 29 */ + "", "", "", "", "I2C0_SCL", /* 30 - 34 */ + "I2C0_SDA", "UART1_TXD", "UART1_RXD", "GEM_TX_CLK", "GEM_TX_D0", /* 35 - 39 */ + "GEM_TX_D1", "GEM_TX_D2", "GEM_TX_D3", "GEM_TX_CTL", "GEM_RX_CLK", /* 40 - 44 */ + "GEM_RX_D0", "GEM_RX_D1", "GEM_RX_D2", "GEM_RX_D3", "GEM_RX_CTL", /* 45 - 49 */ + "GEM_MDC", "GEM_MDIO", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */ + "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */ + "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */ + "", "", "", "", "", /* 65 - 69 */ + "", "", "", "", "", /* 70 - 74 */ + "", "", "ETH_RESET_B", /* 75 - 77, MIO end and EMIO start */ + "", "", /* 78 - 79 */ + "", "", "", "", "", /* 80 - 84 */ + "", "", "", "", "", /* 85 -89 */ + "", "", "", "", "", /* 90 - 94 */ + "", "", "", "", "", /* 95 - 99 */ + "", "", "", "", "", /* 100 - 104 */ + "", "", "", "", "", /* 105 - 109 */ + "", "", "", "", "", /* 110 - 114 */ + "", "", "", "", "", /* 115 - 119 */ + "", "", "", "", "", /* 120 - 124 */ + "", "", "", "", "", /* 125 - 129 */ + "", "", "", "", "", /* 130 - 134 */ + "", "", "", "", "", /* 135 - 139 */ + "", "", "", "", "", /* 140 - 144 */ + "", "", "", "", "", /* 145 - 149 */ + "", "", "", "", "", /* 150 - 154 */ + "", "", "", "", "", /* 155 - 159 */ + "", "", "", "", "", /* 160 - 164 */ + "", "", "", "", "", /* 165 - 169 */ + "", "", "", ""; /* 170 - 173 */ +}; + +&gem1 { /* gem1 MIO38-49, MDIO MIO50/51 */ + status = "okay"; + phy-mode = "rgmii-id"; + phy-handle = <&phy0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gem1_default>; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@1 { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <1>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&gpio 77 GPIO_ACTIVE_LOW>; + reset-assert-us = <100>; + reset-deassert-us = <280>; + }; + }; +}; + +&i2c0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c0_default>; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + scl-gpios = <&gpio 34 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio 35 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; +}; + +&i2c1 { /* i2c1 MIO 24-25 */ + status = "okay"; + bootph-all; + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + + /* Use for storing information about SC board */ + eeprom: eeprom@54 { /* u34 - m24128 16kB */ + compatible = "st,24c128", "atmel,24c128"; + reg = <0x54>; /* & 0x5c */ + bootph-all; + }; +}; + +/* USB 3.0 only */ +&psgtr { + status = "okay"; + /* nc, nc, usb3 */ + clocks = <&si5332_2>; + clock-names = "ref2"; +}; + +&qspi { /* MIO 0-5 */ + status = "okay"; + /* QSPI should also have PINCTRL setup */ + flash@0 { + compatible = "mt25qu512a", "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + spi-max-frequency = <40000000>; /* 40MHz */ + partition@0 { + label = "Image Selector"; + reg = <0x0 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@80000 { + label = "Image Selector Golden"; + reg = <0x80000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@100000 { + label = "Persistent Register"; + reg = <0x100000 0x20000>; /* 128KB */ + }; + partition@120000 { + label = "Persistent Register Backup"; + reg = <0x120000 0x20000>; /* 128KB */ + }; + partition@140000 { + label = "Open_1"; + reg = <0x140000 0xC0000>; /* 768KB */ + }; + partition@200000 { + label = "Image A (FSBL, PMU, ATF, U-Boot)"; + reg = <0x200000 0xD00000>; /* 13MB */ + }; + partition@f00000 { + label = "ImgSel Image A Catch"; + reg = <0xF00000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@f80000 { + label = "Image B (FSBL, PMU, ATF, U-Boot)"; + reg = <0xF80000 0xD00000>; /* 13MB */ + }; + partition@1c80000 { + label = "ImgSel Image B Catch"; + reg = <0x1C80000 0x80000>; /* 512KB */ + read-only; + lock; + }; + partition@1d00000 { + label = "Open_2"; + reg = <0x1D00000 0x100000>; /* 1MB */ + }; + partition@1e00000 { + label = "Recovery Image"; + reg = <0x1E00000 0x200000>; /* 2MB */ + read-only; + lock; + }; + partition@2000000 { + label = "Recovery Image Backup"; + reg = <0x2000000 0x200000>; /* 2MB */ + read-only; + lock; + }; + partition@2200000 { + label = "U-Boot storage variables"; + reg = <0x2200000 0x20000>; /* 128KB */ + }; + partition@2220000 { + label = "U-Boot storage variables backup"; + reg = <0x2220000 0x20000>; /* 128KB */ + }; + partition@2240000 { + label = "SHA256"; + reg = <0x2240000 0x40000>; /* 256B but 256KB sector */ + read-only; + lock; + }; + partition@2280000 { + label = "Secure OS Storage"; + reg = <0x2280000 0x20000>; /* 128KB */ + }; + partition@22A0000 { + label = "User"; + reg = <0x22A0000 0x1d60000>; /* 29.375 MB */ + }; + }; +}; + +&sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */ + status = "okay"; + non-removable; + disable-wp; + bus-width = <8>; + xlnx,mio-bank = <0>; +}; + +&ttc0 { + status = "okay"; + #pwm-cells = <3>; +}; + +&uart1 { /* uart0 MIO36-37 */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; +}; + +&pinctrl0 { /* required by spec */ + status = "okay"; + + pinctrl_uart1_default: uart1-default { + conf { + groups = "uart1_9_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO37"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO36"; + bias-disable; + }; + + mux { + groups = "uart1_9_grp"; + function = "uart1"; + }; + }; + + pinctrl_i2c0_default: i2c0-default { + mux { + groups = "i2c0_8_grp"; + function = "i2c0"; + }; + + conf { + groups = "i2c0_8_grp"; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_i2c0_gpio: i2c0-gpio { + mux { + groups = "gpio0_34_grp", "gpio0_35_grp"; + function = "gpio0"; + }; + + conf { + groups = "gpio0_34_grp", "gpio0_35_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_i2c1_default: i2c1-default { + conf { + groups = "i2c1_6_grp"; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + mux { + groups = "i2c1_6_grp"; + function = "i2c1"; + }; + }; + + pinctrl_i2c1_gpio: i2c1-gpio { + conf { + groups = "gpio0_24_grp", "gpio0_25_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + mux { + groups = "gpio0_24_grp", "gpio0_25_grp"; + function = "gpio0"; + }; + }; + + pinctrl_gem1_default: gem1-default { + conf { + groups = "ethernet1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO44", "MIO46", "MIO48"; + bias-high-impedance; + low-power-disable; + }; + + conf-bootstrap { + pins = "MIO45", "MIO47", "MIO49"; + bias-disable; + low-power-disable; + }; + + conf-tx { + pins = "MIO38", "MIO39", "MIO40", + "MIO41", "MIO42", "MIO43"; + bias-disable; + low-power-enable; + }; + + conf-mdio { + groups = "mdio1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + + mux-mdio { + function = "mdio1"; + groups = "mdio1_0_grp"; + }; + + mux { + function = "ethernet1"; + groups = "ethernet1_0_grp"; + }; + }; +}; |