diff options
23 files changed, 1635 insertions, 27 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 2be36cf1d7e..e034668d757 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1134,6 +1134,7 @@ dtb-$(CONFIG_ASPEED_AST2600) += \ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb dtb-$(CONFIG_STM32MP13X) += \ + stm32mp135f-dhcor-dhsbc.dtb \ stm32mp135f-dk.dtb dtb-$(CONFIG_STM32MP15X) += \ diff --git a/arch/arm/dts/stm32mp13-pinctrl.dtsi b/arch/arm/dts/stm32mp13-pinctrl.dtsi index 27e0c382678..c01d39f03ea 100644 --- a/arch/arm/dts/stm32mp13-pinctrl.dtsi +++ b/arch/arm/dts/stm32mp13-pinctrl.dtsi @@ -6,6 +6,12 @@ #include <dt-bindings/pinctrl/stm32-pinfunc.h> &pinctrl { + adc1_pins_a: adc1-pins-0 { + pins { + pinmux = <STM32_PINMUX('A', 3, ANALOG)>; /* ADC1 in12 */ + }; + }; + adc1_usb_cc_pins_a: adc1-usb-cc-pins-0 { pins { pinmux = <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */ @@ -13,6 +19,104 @@ }; }; + adc1_usb_cc_pins_b: adc1-usb-cc-pins-1 { + pins { + pinmux = <STM32_PINMUX('A', 5, ANALOG)>, /* ADC1_INP2 */ + <STM32_PINMUX('F', 13, ANALOG)>; /* ADC1_INP11 */ + }; + }; + + eth1_rgmii_pins_a: eth1-rgmii-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('E', 5, AF10)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('C', 1, AF11)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */ + <STM32_PINMUX('G', 2, AF11)>; /* ETH_MDC */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + + pins2 { + pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */ + <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */ + <STM32_PINMUX('A', 7, AF11)>, /* ETH_RGMII_RX_CTL */ + <STM32_PINMUX('D', 7, AF10)>; /* ETH_RGMII_RX_CLK */ + bias-disable; + }; + + }; + + eth1_rgmii_sleep_pins_a: eth1-rgmii-sleep-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('E', 5, ANALOG)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */ + <STM32_PINMUX('G', 2, ANALOG)>, /* ETH_MDC */ + <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('B', 0, ANALOG)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('A', 7, ANALOG)>, /* ETH_RGMII_RX_CTL */ + <STM32_PINMUX('D', 7, ANALOG)>; /* ETH_RGMII_RX_CLK */ + }; + }; + + eth2_rgmii_pins_a: eth2-rgmii-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 7, AF11)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 11, AF10)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('G', 1, AF10)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('E', 6, AF11)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('F', 6, AF11)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('G', 3, AF10)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('B', 6, AF11)>, /* ETH_MDIO */ + <STM32_PINMUX('G', 5, AF10)>; /* ETH_MDC */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + + pins2 { + pinmux = <STM32_PINMUX('F', 4, AF11)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('E', 2, AF10)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('H', 6, AF12)>, /* ETH_RGMII_RXD2 */ + <STM32_PINMUX('A', 8, AF11)>, /* ETH_RGMII_RXD3 */ + <STM32_PINMUX('A', 12, AF11)>, /* ETH_RGMII_RX_CTL */ + <STM32_PINMUX('H', 11, AF11)>; /* ETH_RGMII_RX_CLK */ + bias-disable; + }; + }; + + eth2_rgmii_sleep_pins_a: eth2-rgmii-sleep-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 7, ANALOG)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('G', 8, ANALOG)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('F', 6, ANALOG)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('B', 2, ANALOG)>, /* ETH_MDIO */ + <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_MDC */ + <STM32_PINMUX('F', 4, ANALOG)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_RXD2 */ + <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_RXD3 */ + <STM32_PINMUX('A', 12, ANALOG)>, /* ETH_RGMII_RX_CTL */ + <STM32_PINMUX('H', 11, ANALOG)>; /* ETH_RGMII_RX_CLK */ + }; + }; + i2c1_pins_a: i2c1-0 { pins { pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */ @@ -47,6 +151,63 @@ }; }; + i2c5_pins_b: i2c5-1 { + pins { + pinmux = <STM32_PINMUX('D', 1, AF4)>, /* I2C5_SCL */ + <STM32_PINMUX('E', 13, AF4)>; /* I2C5_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c5_sleep_pins_b: i2c5-sleep-1 { + pins { + pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* I2C5_SCL */ + <STM32_PINMUX('E', 13, ANALOG)>; /* I2C5_SDA */ + }; + }; + + m_can1_pins_a: m-can1-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 10, AF9)>; /* CAN1_TX */ + slew-rate = <1>; + drive-push-pull; + bias-disable; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 0, AF9)>; /* CAN1_RX */ + bias-disable; + }; + }; + + m_can1_sleep_pins_a: m_can1-sleep-0 { + pins { + pinmux = <STM32_PINMUX('G', 10, ANALOG)>, /* CAN1_TX */ + <STM32_PINMUX('D', 0, ANALOG)>; /* CAN1_RX */ + }; + }; + + m_can2_pins_a: m-can2-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 0, AF9)>; /* CAN2_TX */ + slew-rate = <1>; + drive-push-pull; + bias-disable; + }; + pins2 { + pinmux = <STM32_PINMUX('E', 0, AF9)>; /* CAN2_RX */ + bias-disable; + }; + }; + + m_can2_sleep_pins_a: m_can2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('G', 0, ANALOG)>, /* CAN2_TX */ + <STM32_PINMUX('E', 0, ANALOG)>; /* CAN2_RX */ + }; + }; + mcp23017_pins_a: mcp23017-0 { pins { pinmux = <STM32_PINMUX('G', 12, GPIO)>; @@ -84,6 +245,21 @@ }; }; + pwm5_pins_a: pwm5-0 { + pins { + pinmux = <STM32_PINMUX('H', 12, AF2)>; /* TIM5_CH3 */ + bias-pull-down; + drive-push-pull; + slew-rate = <0>; + }; + }; + + pwm5_sleep_pins_a: pwm5-sleep-0 { + pins { + pinmux = <STM32_PINMUX('H', 12, ANALOG)>; /* TIM5_CH3 */ + }; + }; + pwm8_pins_a: pwm8-0 { pins { pinmux = <STM32_PINMUX('E', 5, AF3)>; /* TIM8_CH3 */ @@ -99,6 +275,21 @@ }; }; + pwm13_pins_a: pwm13-0 { + pins { + pinmux = <STM32_PINMUX('A', 6, AF9)>; /* TIM13_CH1 */ + bias-pull-down; + drive-push-pull; + slew-rate = <0>; + }; + }; + + pwm13_sleep_pins_a: pwm13-sleep-0 { + pins { + pinmux = <STM32_PINMUX('A', 6, ANALOG)>; /* TIM13_CH1 */ + }; + }; + pwm14_pins_a: pwm14-0 { pins { pinmux = <STM32_PINMUX('F', 9, AF9)>; /* TIM14_CH1 */ @@ -114,6 +305,89 @@ }; }; + qspi_clk_pins_a: qspi-clk-0 { + pins { + pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + }; + + qspi_clk_sleep_pins_a: qspi-clk-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 10, ANALOG)>; /* QSPI_CLK */ + }; + }; + + qspi_bk1_pins_a: qspi-bk1-0 { + pins { + pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */ + <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */ + <STM32_PINMUX('D', 11, AF9)>, /* QSPI_BK1_IO2 */ + <STM32_PINMUX('H', 7, AF13)>; /* QSPI_BK1_IO3 */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + }; + + qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* QSPI_BK1_IO0 */ + <STM32_PINMUX('F', 9, ANALOG)>, /* QSPI_BK1_IO1 */ + <STM32_PINMUX('D', 11, ANALOG)>, /* QSPI_BK1_IO2 */ + <STM32_PINMUX('H', 7, ANALOG)>; /* QSPI_BK1_IO3 */ + }; + }; + + qspi_cs1_pins_a: qspi-cs1-0 { + pins { + pinmux = <STM32_PINMUX('B', 2, AF9)>; /* QSPI_BK1_NCS */ + bias-pull-up; + drive-push-pull; + slew-rate = <1>; + }; + }; + + qspi_cs1_sleep_pins_a: qspi-cs1-sleep-0 { + pins { + pinmux = <STM32_PINMUX('B', 2, ANALOG)>; /* QSPI_BK1_NCS */ + }; + }; + + sai1a_pins_a: sai1a-0 { + pins { + pinmux = <STM32_PINMUX('A', 4, AF12)>, /* SAI1_SCK_A */ + <STM32_PINMUX('D', 6, AF6)>, /* SAI1_SD_A */ + <STM32_PINMUX('E', 11, AF6)>; /* SAI1_FS_A */ + slew-rate = <0>; + drive-push-pull; + bias-disable; + }; + }; + + sai1a_sleep_pins_a: sai1a-sleep-0 { + pins { + pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* SAI1_SCK_A */ + <STM32_PINMUX('D', 6, ANALOG)>, /* SAI1_SD_A */ + <STM32_PINMUX('E', 11, ANALOG)>; /* SAI1_FS_A */ + }; + }; + + sai1b_pins_a: sai1b-0 { + pins { + pinmux = <STM32_PINMUX('A', 0, AF6)>; /* SAI1_SD_B */ + bias-disable; + }; + }; + + sai1b_sleep_pins_a: sai1b-sleep-0 { + pins { + pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* SAI1_SD_B */ + }; + }; + sdmmc1_b4_pins_a: sdmmc1-b4-0 { pins { pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ @@ -216,6 +490,73 @@ }; }; + sdmmc2_d47_pins_a: sdmmc2-d47-0 { + pins { + pinmux = <STM32_PINMUX('F', 0, AF10)>, /* SDMMC2_D4 */ + <STM32_PINMUX('B', 9, AF10)>, /* SDMMC2_D5 */ + <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + }; + + sdmmc2_d47_sleep_pins_a: sdmmc2-d47-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC2_D4 */ + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC2_D5 */ + <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */ + }; + }; + + spi2_pins_a: spi2-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 10, AF6)>, /* SPI2_SCK */ + <STM32_PINMUX('H', 10, AF6)>; /* SPI2_MOSI */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + + pins2 { + pinmux = <STM32_PINMUX('B', 5, AF5)>; /* SPI2_MISO */ + bias-disable; + }; + }; + + spi2_sleep_pins_a: spi2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* SPI2_SCK */ + <STM32_PINMUX('B', 5, ANALOG)>, /* SPI2_MISO */ + <STM32_PINMUX('H', 10, ANALOG)>; /* SPI2_MOSI */ + }; + }; + + spi3_pins_a: spi3-0 { + pins1 { + pinmux = <STM32_PINMUX('H', 13, AF6)>, /* SPI3_SCK */ + <STM32_PINMUX('F', 1, AF5)>; /* SPI3_MOSI */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + + pins2 { + pinmux = <STM32_PINMUX('D', 4, AF5)>; /* SPI3_MISO */ + bias-disable; + }; + }; + + spi3_sleep_pins_a: spi3-sleep-0 { + pins { + pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* SPI3_SCK */ + <STM32_PINMUX('D', 4, ANALOG)>, /* SPI3_MISO */ + <STM32_PINMUX('F', 1, ANALOG)>; /* SPI3_MOSI */ + }; + }; + spi5_pins_a: spi5-0 { pins1 { pinmux = <STM32_PINMUX('H', 7, AF6)>, /* SPI5_SCK */ @@ -276,6 +617,77 @@ }; }; + uart4_pins_b: uart4-1 { + pins1 { + pinmux = <STM32_PINMUX('A', 9, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */ + bias-pull-up; + }; + }; + + uart4_idle_pins_b: uart4-idle-1 { + pins1 { + pinmux = <STM32_PINMUX('A', 9, ANALOG)>; /* UART4_TX */ + }; + pins2 { + pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */ + bias-pull-up; + }; + }; + + uart4_sleep_pins_b: uart4-sleep-1 { + pins { + pinmux = <STM32_PINMUX('A', 9, ANALOG)>, /* UART4_TX */ + <STM32_PINMUX('D', 8, ANALOG)>; /* UART4_RX */ + }; + }; + + uart7_pins_a: uart7-0 { + pins1 { + pinmux = <STM32_PINMUX('H', 2, AF8)>, /* UART7_TX */ + <STM32_PINMUX('B', 12, AF7)>; /* UART7_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('E', 10, AF7)>, /* UART7_RX */ + <STM32_PINMUX('G', 7, AF8)>; /* UART7_CTS_NSS */ + bias-disable; + }; + }; + + uart7_idle_pins_a: uart7-idle-0 { + pins1 { + pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* UART7_TX */ + <STM32_PINMUX('G', 7, ANALOG)>; /* UART7_CTS_NSS */ + }; + pins2 { + pinmux = <STM32_PINMUX('B', 12, AF7)>; /* UART7_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { + pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */ + bias-disable; + }; + }; + + uart7_sleep_pins_a: uart7-sleep-0 { + pins { + pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* UART7_TX */ + <STM32_PINMUX('B', 12, ANALOG)>, /* UART7_RTS */ + <STM32_PINMUX('E', 10, ANALOG)>, /* UART7_RX */ + <STM32_PINMUX('G', 7, ANALOG)>; /* UART7_CTS_NSS */ + }; + }; + uart8_pins_a: uart8-0 { pins1 { pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */ @@ -347,6 +759,36 @@ }; }; + usart1_pins_b: usart1-1 { + pins1 { + pinmux = <STM32_PINMUX('C', 0, AF7)>; /* USART1_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 14, AF7)>; /* USART1_RX */ + bias-pull-up; + }; + }; + + usart1_idle_pins_b: usart1-idle-1 { + pins1 { + pinmux = <STM32_PINMUX('C', 0, ANALOG)>; /* USART1_TX */ + }; + pins2 { + pinmux = <STM32_PINMUX('D', 14, AF7)>; /* USART1_RX */ + bias-pull-up; + }; + }; + + usart1_sleep_pins_b: usart1-sleep-1 { + pins { + pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */ + <STM32_PINMUX('D', 14, ANALOG)>; /* USART1_RX */ + }; + }; + usart2_pins_a: usart2-0 { pins1 { pinmux = <STM32_PINMUX('H', 12, AF1)>, /* USART2_TX */ @@ -387,4 +829,45 @@ <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */ }; }; + + usart2_pins_b: usart2-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 11, AF1)>, /* USART2_TX */ + <STM32_PINMUX('A', 1, AF7)>; /* USART2_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 15, AF1)>, /* USART2_RX */ + <STM32_PINMUX('E', 15, AF3)>; /* USART2_CTS_NSS */ + bias-disable; + }; + }; + + usart2_idle_pins_b: usart2-idle-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* USART2_TX */ + <STM32_PINMUX('E', 15, ANALOG)>; /* USART2_CTS_NSS */ + }; + pins2 { + pinmux = <STM32_PINMUX('A', 1, AF7)>; /* USART2_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { + pinmux = <STM32_PINMUX('D', 15, AF1)>; /* USART2_RX */ + bias-disable; + }; + }; + + usart2_sleep_pins_b: usart2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* USART2_TX */ + <STM32_PINMUX('A', 1, ANALOG)>, /* USART2_RTS */ + <STM32_PINMUX('D', 15, ANALOG)>, /* USART2_RX */ + <STM32_PINMUX('E', 15, ANALOG)>; /* USART2_CTS_NSS */ + }; + }; }; diff --git a/arch/arm/dts/stm32mp131.dtsi b/arch/arm/dts/stm32mp131.dtsi index 215ad9298de..ad331b73d18 100644 --- a/arch/arm/dts/stm32mp131.dtsi +++ b/arch/arm/dts/stm32mp131.dtsi @@ -1092,6 +1092,30 @@ <&scmi_clk CK_SCMI_LSI>; }; + pwr_regulators: pwr@50001000 { + compatible = "st,stm32mp1,pwr-reg"; + reg = <0x50001000 0x10>; + status = "disabled"; + + reg11: reg11 { + regulator-name = "reg11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + reg18: reg18 { + regulator-name = "reg18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + usb33: usb33 { + regulator-name = "usb33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + exti: interrupt-controller@5000d000 { compatible = "st,stm32mp13-exti", "syscon"; interrupt-controller; @@ -1304,6 +1328,37 @@ status = "disabled"; }; + eth1: eth1@5800a000 { + compatible = "snps,dwmac-4.20a", "st,stm32mp13-dwmac"; + reg = <0x5800a000 0x2000>; + reg-names = "stmmaceth"; + interrupts-extended = <&intc GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, + <&exti 68 1>; + interrupt-names = "macirq", "eth_wake_irq"; + clock-names = "stmmaceth", + "mac-clk-tx", + "mac-clk-rx", + "ethstp", + "eth-ck"; + clocks = <&rcc ETH1MAC>, + <&rcc ETH1TX>, + <&rcc ETH1RX>, + <&rcc ETH1STP>, + <&rcc ETH1CK_K>; + st,syscon = <&syscfg 0x4 0xff0000>; + snps,mixed-burst; + snps,pbl = <2>; + snps,axi-config = <&stmmac_axi_config_1>; + snps,tso; + status = "disabled"; + + stmmac_axi_config_1: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; + }; + usbh_ohci: usb@5800c000 { compatible = "generic-ohci"; reg = <0x5800c000 0x1000>; @@ -1380,6 +1435,12 @@ ts_cal2: calib@5e { reg = <0x5e 0x2>; }; + ethernet_mac1_address: mac1@e4 { + reg = <0xe4 0x6>; + }; + ethernet_mac2_address: mac2@ea { + reg = <0xea 0x6>; + }; }; /* diff --git a/arch/arm/dts/stm32mp133.dtsi b/arch/arm/dts/stm32mp133.dtsi index df451c3c2a2..5cd5bde9535 100644 --- a/arch/arm/dts/stm32mp133.dtsi +++ b/arch/arm/dts/stm32mp133.dtsi @@ -64,5 +64,35 @@ }; }; }; + + eth2: eth2@5800e000 { + compatible = "snps,dwmac-4.20a", "st,stm32mp13-dwmac"; + reg = <0x5800e000 0x2000>; + reg-names = "stmmaceth"; + interrupts-extended = <&intc GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + clock-names = "stmmaceth", + "mac-clk-tx", + "mac-clk-rx", + "ethstp", + "eth-ck"; + clocks = <&rcc ETH2MAC>, + <&rcc ETH2TX>, + <&rcc ETH2RX>, + <&rcc ETH2STP>, + <&rcc ETH2CK_K>; + st,syscon = <&syscfg 0x4 0xff000000>; + snps,mixed-burst; + snps,pbl = <2>; + snps,axi-config = <&stmmac_axi_config_2>; + snps,tso; + status = "disabled"; + + stmmac_axi_config_2: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; + }; }; }; diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi new file mode 100644 index 00000000000..d718aae16ca --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut <marex@denx.de> + */ + +#include "stm32mp13xx-dhcor-u-boot.dtsi" + +&uart4 { + bootph-all; +}; + +&uart4_pins_b { + bootph-all; + + pins1 { + bootph-all; + }; + pins2 { + bootph-all; + }; +}; + +&usbphyc { + bootph-all; +}; diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts new file mode 100644 index 00000000000..fc1c48ad56d --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts @@ -0,0 +1,383 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut <marex@denx.de> + * + * DHCOR STM32MP13 variant: + * DHCR-STM32MP135F-C100-R051-EE-F0409-SPI4-RTC-WBT-I-01LG + * DHCOR PCB number: 718-100 or newer + * DHSBC PCB number: 719-100 or newer + */ + +/dts-v1/; + +#include <dt-bindings/regulator/st,stm32mp13-regulator.h> +#include "stm32mp135.dtsi" +#include "stm32mp13xf.dtsi" +#include "stm32mp13xx-dhcor-som.dtsi" + +/ { + model = "DH electronics STM32MP135F DHCOR DHSBC"; + compatible = "dh,stm32mp135f-dhcor-dhsbc", + "dh,stm32mp135f-dhcor-som", + "st,stm32mp135"; + + aliases { + ethernet0 = ð1; + ethernet1 = ð2; + serial2 = &usart1; + serial3 = &usart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&adc_1 { + pinctrl-names = "default"; + pinctrl-0 = <&adc1_pins_a &adc1_usb_cc_pins_b>; + vdda-supply = <&vdd_adc>; + vref-supply = <&vdd_adc>; + status = "okay"; + + adc1: adc@0 { + status = "okay"; + + /* + * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in2 & in11. + * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: + * 5 * (5.1 + 47kOhms) * 5pF => 1.3us. + * Use arbitrary margin here (e.g. 5us). + * + * The pinmux pins must be set as ANALOG, use datasheet + * DS13483 Table 7. STM32MP135C/F ball definitions to + * find out which 'pin name' maps to which 'additional + * functions', which lists the mapping between pin and + * ADC channel. In this case, PA5 maps to ADC1_INP2 and + * PF13 maps to ADC1_INP11 . + */ + channel@2 { + reg = <2>; + st,min-sample-time-ns = <5000>; + }; + + channel@11 { + reg = <11>; + st,min-sample-time-ns = <5000>; + }; + + /* Expansion connector: INP12:pin29 */ + channel@12 { + reg = <12>; + st,min-sample-time-ns = <5000>; + }; + }; +}; + +ð1 { + status = "okay"; + pinctrl-0 = <ð1_rgmii_pins_a>; + pinctrl-1 = <ð1_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + st,ext-phyclk; + nvmem-cells = <ðernet_mac1_address>; + nvmem-cell-names = "mac-address"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + ethphy1: ethernet-phy@1 { + /* RTL8211F */ + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpiog>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + reg = <1>; + reset-assert-us = <15000>; + reset-deassert-us = <55000>; + reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð2 { + status = "okay"; + pinctrl-0 = <ð2_rgmii_pins_a>; + pinctrl-1 = <ð2_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + phy-handle = <ðphy2>; + st,ext-phyclk; + nvmem-cells = <ðernet_mac2_address>; + nvmem-cell-names = "mac-address"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + ethphy2: ethernet-phy@1 { + /* RTL8211F */ + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpiog>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + reg = <1>; + reset-assert-us = <15000>; + reset-deassert-us = <55000>; + reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpioa { + gpio-line-names = "", "", "", "", + "", "DHSBC_USB_PWR_CC1", "", "", + "", "", "", "DHSBC_nETH1_RST", + "", "DHCOR_HW-CODING_0", "", ""; +}; + +&gpiob { + gpio-line-names = "", "", "", "", + "", "", "", "DHCOR_BT_HOST_WAKE", + "", "", "", "", + "", "DHSBC_nTPM_CS", "", ""; +}; + +&gpioc { + gpio-line-names = "", "", "", "DHSBC_USB_5V_MEAS", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiod { + gpio-line-names = "", "", "", "", + "", "DHCOR_RAM-CODING_0", "", "", + "", "DHCOR_RAM-CODING_1", "", "", + "", "", "", ""; +}; + +&gpioe { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "DHSBC_nTPM_RST", "", "", + "DHSBC_nTPM_PIRQ", "", "DHCOR_WL_HOST_WAKE", ""; +}; + +&gpiof { + gpio-line-names = "", "", "DHSBC_USB_PWR_nFLT", "", + "", "", "", "", + "", "", "", "", + "DHCOR_WL_REG_ON", "DHSBC_USB_PWR_CC2", "", ""; +}; + +&gpiog { + gpio-line-names = "", "", "", "", + "", "", "", "", + "DHSBC_nETH2_RST", "DHCOR_BT_DEV_WAKE", "", "", + "DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB"; +}; + +&gpioi { + gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1", + "DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT", + "DHSBC_BOOT0", "DHSBC_BOOT1", + "DHSBC_BOOT2", "DHSBC_USB-C_DATA_VBUS"; +}; + +&i2c1 { /* Expansion connector: SDA:pin27 SCL:pin28 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_sleep_pins_a>; + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c5 { /* Expansion connector: SDA:pin3 SCL:pin5 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c5_pins_b>; + pinctrl-1 = <&i2c5_sleep_pins_b>; + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&m_can1 { /* Expansion connector: TX:pin16 RX:pin18 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_a>; + pinctrl-1 = <&m_can1_sleep_pins_a>; + status = "okay"; +}; + +&m_can2 { /* Expansion connector: TX:pin22 RX:pin26 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can2_pins_a>; + pinctrl-1 = <&m_can2_sleep_pins_a>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; + status = "okay"; +}; + +&sai1 { /* Expansion connector: SCK-A:pin12 FS-A:pin35 SD-A:pin38 SD-B:pin40 */ + clocks = <&rcc SAI1>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + clock-names = "pclk", "x8k", "x11k"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai1a_pins_a &sai1b_pins_a>; + pinctrl-1 = <&sai1a_sleep_pins_a &sai1b_sleep_pins_a>; +}; + +&scmi_voltd { + status = "disabled"; +}; + +&spi2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&spi2_pins_a>; + pinctrl-1 = <&spi2_sleep_pins_a>; + cs-gpios = <&gpiob 13 0>; + status = "okay"; + + st33htph: tpm@0 { + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&spi3 { /* Expansion connector: MOSI:pin19 MISO:pin21 SCK:pin22 nCS:pin24 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&spi3_pins_a>; + pinctrl-1 = <&spi3_sleep_pins_a>; + cs-gpios = <&gpiof 3 0>; + status = "disabled"; +}; + +&timers5 { /* Expansion connector: CH3:pin31 */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + pwm { + pinctrl-0 = <&pwm5_pins_a>; + pinctrl-1 = <&pwm5_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@4 { + status = "okay"; + }; +}; + +&timers13 { /* Expansion connector: CH1:pin32 */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + pwm { + pinctrl-0 = <&pwm13_pins_a>; + pinctrl-1 = <&pwm13_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@12 { + status = "okay"; + }; +}; + +&usart1 { /* Expansion connector: RX:pin33 TX:pin37 */ + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart1_pins_b>; + pinctrl-1 = <&usart1_sleep_pins_b>; + pinctrl-2 = <&usart1_idle_pins_b>; + status = "okay"; +}; + +&usart2 { /* Expansion connector: RX:pin10 TX:pin8 RTS:pin11 CTS:pin36 */ + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart2_pins_b>; + pinctrl-1 = <&usart2_sleep_pins_b>; + pinctrl-2 = <&usart2_idle_pins_b>; + uart-has-rtscts; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbh_ohci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + usb33d-supply = <&usb33>; + status = "okay"; +}; + +&usbphyc { + status = "okay"; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; + connector { + compatible = "usb-a-connector"; + vbus-supply = <&vbus_sw>; + }; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + vbus-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>; + label = "Type-C"; + self-powered; + type = "micro"; + }; +}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi new file mode 100644 index 00000000000..ddad6497775 --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut <marex@denx.de> + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/mfd/st,stpmic1.h> +#include <dt-bindings/regulator/st,stm32mp13-regulator.h> +#include "stm32mp13-pinctrl.dtsi" + +/ { + model = "DH electronics STM32MP13xx DHCOR SoM"; + compatible = "dh,stm32mp131a-dhcor-som", + "st,stm32mp131"; + + aliases { + mmc0 = &sdmmc2; + mmc1 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + rtc0 = &rv3032; + spi0 = &qspi; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + optee@dd000000 { + reg = <0xdd000000 0x3000000>; + no-map; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>; + }; + + vin: vin { + compatible = "regulator-fixed"; + regulator-name = "vin"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&i2c3 { + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioi 3 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&vin>; + ldo2-supply = <&vin>; + ldo3-supply = <&vin>; + ldo4-supply = <&vin>; + ldo5-supply = <&vin>; + ldo6-supply = <&vin>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcpu: buck1 { /* VDD_CPU_1V2 */ + regulator-name = "vddcpu"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { /* VDD_DDR_1V35 */ + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { /* VDD_3V3_1V8 */ + regulator-name = "vdd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vddcore: buck4 { /* VDD_CORE_1V2 */ + regulator-name = "vddcore"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_adc: ldo1 { /* VDD_ADC_1V8 */ + regulator-name = "vdd_adc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + vdd_ldo2: ldo2 { /* LDO2_OUT_1V8 */ + regulator-name = "vdd_ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vdd_ldo3: ldo3 { /* LDO3_OUT */ + regulator-name = "vdd_ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO3 0>; + }; + + vdd_usb: ldo4 { /* VDD_USB_3V3 */ + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdd_sd: ldo5 { /* VDD_SD_3V3_1V8 */ + regulator-name = "vdd_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO5 0>; + }; + + vdd_sd2: ldo6 { /* VDD_SD2_3V3_1V8 */ + regulator-name = "vdd_sd2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO6 0>; + }; + + vref_ddr: vref_ddr { /* VREF_DDR_0V675 */ + regulator-name = "vref_ddr"; + regulator-always-on; + }; + + bst_out: boost { /* BST_OUT_5V2 */ + regulator-name = "bst_out"; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; + + eeprom0: eeprom@50 { + compatible = "atmel,24c256"; /* ST M24256 */ + reg = <0x50>; + pagesize = <64>; + }; + + rv3032: rtc@51 { + compatible = "microcrystal,rv3032"; + reg = <0x51>; + interrupts-extended = <&gpioi 0 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a + &qspi_bk1_pins_a + &qspi_cs1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a + &qspi_bk1_sleep_pins_a + &qspi_cs1_sleep_pins_a>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +/* Console UART */ +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_b>; + pinctrl-1 = <&uart4_sleep_pins_b>; + pinctrl-2 = <&uart4_idle_pins_b>; + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +/* Bluetooth */ +&uart7 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart7_pins_a>; + pinctrl-1 = <&uart7_sleep_pins_a>; + pinctrl-2 = <&uart7_idle_pins_a>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "infineon,cyw43439-bt", "brcm,bcm4329-bt"; + max-speed = <3000000>; + device-wakeup-gpios = <&gpiog 9 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; + }; +}; + +/* SDIO WiFi */ +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + non-removable; + st,neg-edge; + vmmc-supply = <&vdd>; + mmc-pwrseq = <&sdio_pwrseq>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + brcmf: bcrmf@1 { /* muRata 1YN */ + reg = <1>; + compatible = "infineon,cyw43439-fmac", "brcm,bcm4329-fmac"; + interrupt-parent = <&gpioe>; + interrupts = <14 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +/* eMMC */ +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + bus-width = <8>; + mmc-ddr-3_3v; + no-sd; + no-sdio; + non-removable; + st,neg-edge; + vmmc-supply = <&vdd>; + vqmmc-supply = <&vdd>; + status = "okay"; +}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi new file mode 100644 index 00000000000..30e3b91bccc --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut <marex@denx.de> + */ + +#include "stm32mp13-u-boot.dtsi" + +/ { + aliases { + eeprom0 = &eeprom0; + }; + + config { + dh,ddr3-coding-gpios = <&gpiod 5 0>, <&gpiod 9 0>; + dh,som-coding-gpios = <&gpioa 13 0>, <&gpioi 1 0>; + }; +}; + +&flash0 { + bootph-pre-ram; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "fsbl1"; + reg = <0x00000000 0x00040000>; + }; + partition@40000 { + label = "fsbl2"; + reg = <0x00040000 0x00040000>; + }; + partition@80000 { + label = "u-boot"; + reg = <0x00080000 0x00360000>; + }; + partition@3e0000 { + label = "u-boot-env-a"; + reg = <0x003e0000 0x00010000>; + }; + partition@3f0000 { + label = "u-boot-env-b"; + reg = <0x003f0000 0x00010000>; + }; + }; +}; + +&sdmmc1 { + status = "disabled"; +}; + +&usbotg_hs { + u-boot,force-b-session-valid; +}; diff --git a/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi b/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi index b780dbd95e2..d07fdcf4bc3 100644 --- a/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi @@ -115,11 +115,11 @@ bootph-all; }; - /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */ + /* VCO = 750.0 MHz => P = 125, Q = 62.5, R = 62.5 */ pll4: st,pll@3 { compatible = "st,stm32mp1-pll"; reg = <3>; - cfg = < 3 98 5 7 7 PQR(1,1,1) >; + cfg = < 3 124 5 9 9 PQR(1,1,1) >; bootph-all; }; }; diff --git a/arch/arm/dts/stm32mp157c-odyssey.dts b/arch/arm/dts/stm32mp157c-odyssey.dts index 17bcf56f744..4cc5e076838 100644 --- a/arch/arm/dts/stm32mp157c-odyssey.dts +++ b/arch/arm/dts/stm32mp157c-odyssey.dts @@ -75,13 +75,15 @@ phy-mode = "rgmii-id"; max-speed = <1000>; phy-handle = <&phy0>; + phy-reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; + st,ext-phyclk; mdio0 { #address-cells = <1>; #size-cells = <0>; compatible = "snps,dwmac-mdio"; - phy0: ethernet-phy@0 { - reg = <0>; + phy0: ethernet-phy@7 { + reg = <7>; }; }; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts b/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts index 1ef9ac29cea..90625bf6b60 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts +++ b/arch/arm/dts/stm32mp15xx-dhcom-drc02.dts @@ -11,5 +11,7 @@ / { model = "DH Electronics STM32MP15xx DHCOM DRC02"; - compatible = "dh,stm32mp15xx-dhcom-drc02", "st,stm32mp1xx"; + compatible = "dh,stm32mp15xx-dhcom-drc02", + "dh,stm32mp15xx-dhcom-som", + "st,stm32mp1xx"; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts b/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts index e2e01e2146c..b2e450aa13b 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts +++ b/arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts @@ -11,5 +11,7 @@ / { model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)"; - compatible = "dh,stm32mp15xx-dhcom-pdk2", "st,stm32mp15x"; + compatible = "dh,stm32mp15xx-dhcom-pdk2", + "dh,stm32mp15xx-dhcom-som", + "st,stm32mp15x"; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts b/arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts index 06770b47873..3e908102f61 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts +++ b/arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts @@ -11,5 +11,7 @@ / { model = "DH Electronics STM32MP15xx DHCOM PicoITX"; - compatible = "dh,stm32mp15xx-dhcom-picoitx", "st,stm32mp1xx"; + compatible = "dh,stm32mp15xx-dhcom-picoitx", + "dh,stm32mp15xx-dhcom-som", + "st,stm32mp1xx"; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi index 1b445619325..d7b78cdcfa9 100644 --- a/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +++ b/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi @@ -26,6 +26,7 @@ u-boot,error-led = "error"; dh,som-coding-gpios = <&gpiof 12 0>, <&gpiof 13 0>, <&gpiof 15 0>; dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>; + dh,mac-coding-gpios = <&gpioc 3 0>; }; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts index 76ac5a873c1..dd8fcecbca5 100644 --- a/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts +++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts @@ -14,5 +14,7 @@ / { model = "Arrow Electronics STM32MP15xx Avenger96 board"; - compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x"; + compatible = "arrow,stm32mp15xx-avenger96", + "dh,stm32mp15xx-dhcor-som", + "st,stm32mp15x"; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts index 77dd944ff53..c1f99c1685e 100644 --- a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts +++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts @@ -12,5 +12,7 @@ / { model = "DH electronics STM32MP15xx DHCOR DRC Compact"; - compatible = "dh,stm32mp15xx-dhcor-drc-compact", "st,stm32mp1xx"; + compatible = "dh,stm32mp15xx-dhcor-drc-compact", + "dh,stm32mp15xx-dhcor-som", + "st,stm32mp1xx"; }; diff --git a/arch/arm/dts/stm32mp15xx-dhcor-testbench.dts b/arch/arm/dts/stm32mp15xx-dhcor-testbench.dts index c9163e1c028..5fdd762ddbf 100644 --- a/arch/arm/dts/stm32mp15xx-dhcor-testbench.dts +++ b/arch/arm/dts/stm32mp15xx-dhcor-testbench.dts @@ -9,7 +9,9 @@ / { model = "DH electronics STM32MP15xx DHCOR Testbench"; - compatible = "dh,stm32mp15xx-dhcor-testbench", "st,stm32mp1xx"; + compatible = "dh,stm32mp15xx-dhcor-testbench", + "dh,stm32mp15xx-dhcor-som", + "st,stm32mp1xx"; aliases { ethernet0 = ðernet0; diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig index b9af03d57e3..d5934a92771 100644 --- a/arch/arm/mach-stm32mp/Kconfig +++ b/arch/arm/mach-stm32mp/Kconfig @@ -155,4 +155,21 @@ source "arch/arm/mach-stm32mp/Kconfig.13x" source "arch/arm/mach-stm32mp/Kconfig.15x" source "arch/arm/mach-stm32mp/Kconfig.25x" source "arch/arm/mach-stm32mp/cmd_stm32prog/Kconfig" + +config STM32MP15_PWR + bool "Enable driver for STM32MP15x PWR" + depends on DM_REGULATOR && DM_PMIC && (STM32MP13X || STM32MP15X) + default y if STM32MP15X + help + This config enables implementation of driver-model pmic and + regulator uclass features for access to STM32MP15x PWR. + +config SPL_STM32MP15_PWR + bool "Enable driver for STM32MP15x PWR in SPL" + depends on SPL && SPL_DM_REGULATOR && SPL_DM_PMIC && (STM32MP13X || STM32MP15X) + default y if STM32MP15X + help + This config enables implementation of driver-model pmic and + regulator uclass features for access to STM32MP15x PWR in SPL. + endif diff --git a/arch/arm/mach-stm32mp/Kconfig.15x b/arch/arm/mach-stm32mp/Kconfig.15x index 71c14eb4955..d99aa9fd694 100644 --- a/arch/arm/mach-stm32mp/Kconfig.15x +++ b/arch/arm/mach-stm32mp/Kconfig.15x @@ -77,22 +77,6 @@ config TARGET_ICORE_STM32MP1 endchoice -config STM32MP15_PWR - bool "Enable driver for STM32MP15x PWR" - depends on DM_REGULATOR && DM_PMIC - default y - help - This config enables implementation of driver-model pmic and - regulator uclass features for access to STM32MP15x PWR. - -config SPL_STM32MP15_PWR - bool "Enable driver for STM32MP15x PWR in SPL" - depends on SPL && SPL_DM_REGULATOR && SPL_DM_PMIC - default y - help - This config enables implementation of driver-model pmic and - regulator uclass features for access to STM32MP15x PWR in SPL. - config TEXT_BASE default 0xC0100000 diff --git a/arch/arm/mach-stm32mp/dram_init.c b/arch/arm/mach-stm32mp/dram_init.c index 78b12fcbb6a..6024959b97e 100644 --- a/arch/arm/mach-stm32mp/dram_init.c +++ b/arch/arm/mach-stm32mp/dram_init.c @@ -6,6 +6,7 @@ #define LOG_CATEGORY LOGC_ARCH #include <dm.h> +#include <efi_loader.h> #include <image.h> #include <init.h> #include <lmb.h> @@ -74,3 +75,14 @@ phys_addr_t board_get_usable_ram_top(phys_size_t total_size) return reg + size; } + +void efi_add_known_memory(void) +{ + if (IS_ENABLED(CONFIG_EFI_LOADER)) + /* + * Memory over ram_top is reserved to OPTEE. + * Declare to EFI only memory area below ram_top + */ + efi_add_memory_map(gd->ram_base, gd->ram_top - gd->ram_base, + EFI_CONVENTIONAL_MEMORY); +} diff --git a/board/dhelectronics/dh_stm32mp1/board.c b/board/dhelectronics/dh_stm32mp1/board.c index 20c9d70737e..ebd45f9053f 100644 --- a/board/dhelectronics/dh_stm32mp1/board.c +++ b/board/dhelectronics/dh_stm32mp1/board.c @@ -37,6 +37,7 @@ #include <power/regulator.h> #include <remoteproc.h> #include <reset.h> +#include <spl.h> #include <syscon.h> #include <usb.h> #include <usb/dwc2_udc.h> @@ -672,12 +673,69 @@ void board_quiesce_devices(void) #endif } +static void dh_stm32_ks8851_fixup(void *blob) +{ + struct gpio_desc ks8851intrn; + bool compatible = false; + int ks8851intrn_value; + const char *prop; + ofnode node; + int idx = 0; + int offset; + int ret; + + /* Do nothing if not STM32MP15xx DHCOM SoM */ + while ((prop = fdt_stringlist_get(blob, 0, "compatible", idx++, NULL))) { + if (!strstr(prop, "dhcom-som")) + continue; + compatible = true; + break; + } + + if (!compatible) + return; + + /* + * Read state of INTRN pull up resistor, if this pull up is populated, + * KS8851-16MLL is populated as well and should be enabled, otherwise + * it should be disabled. + */ + node = ofnode_path("/config"); + if (!ofnode_valid(node)) + return; + + ret = gpio_request_by_name_nodev(node, "dh,mac-coding-gpios", 0, + &ks8851intrn, GPIOD_IS_IN); + if (ret) + return; + + ks8851intrn_value = dm_gpio_get_value(&ks8851intrn); + + dm_gpio_free(NULL, &ks8851intrn); + + /* Set the 'status' property into KS8851-16MLL DT node. */ + offset = fdt_path_offset(blob, "ethernet1"); + ret = fdt_node_check_compatible(blob, offset, "micrel,ks8851-mll"); + if (ret) /* Not compatible */ + return; + + /* Add a bit of extra space for new 'status' property */ + ret = fdt_shrink_to_minimum(blob, 4096); + if (!ret) + return; + + fdt_setprop_string(blob, offset, "status", + ks8851intrn_value ? "okay" : "disabled"); +} + #if defined(CONFIG_OF_BOARD_SETUP) int ft_board_setup(void *blob, struct bd_info *bd) { const char *buck3path = "/soc/i2c@5c002000/stpmic@33/regulators/buck3"; int buck3off, ret, uv; + dh_stm32_ks8851_fixup(blob); + ret = board_get_regulator_buck3_nvm_uv_av96(&uv); if (ret) /* Not Avenger96 board, do not patch Buck3 in DT. */ return 0; @@ -698,6 +756,13 @@ int ft_board_setup(void *blob, struct bd_info *bd) } #endif +#if defined(CONFIG_SPL_BUILD) +void spl_perform_fixups(struct spl_image_info *spl_image) +{ + dh_stm32_ks8851_fixup(spl_image_fdt_addr(spl_image)); +} +#endif + static void board_copro_image_process(ulong fw_image, size_t fw_size) { int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */ diff --git a/configs/stm32mp13_dhcor_defconfig b/configs/stm32mp13_dhcor_defconfig new file mode 100644 index 00000000000..fb3d86deb64 --- /dev/null +++ b/configs/stm32mp13_dhcor_defconfig @@ -0,0 +1,148 @@ +CONFIG_ARM=y +CONFIG_ARCH_STM32MP=y +CONFIG_TFABOOT=y +CONFIG_SYS_MALLOC_F_LEN=0x1c0000 +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0400000 +CONFIG_ENV_SIZE=0x4000 +CONFIG_ENV_OFFSET=0x3E0000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dhcor-dhsbc" +CONFIG_STM32MP13X=y +CONFIG_DDR_CACHEABLE_SIZE=0x8000000 +CONFIG_CMD_STM32KEY=y +CONFIG_TARGET_ST_STM32MP13X=y +CONFIG_ENV_OFFSET_REDUND=0x3F0000 +CONFIG_CMD_STM32PROG=y +CONFIG_STM32MP15_PWR=y +# CONFIG_ARMV7_NONSEC is not set +CONFIG_SYS_LOAD_ADDR=0xc2000000 +CONFIG_SYS_MEMTEST_START=0xc0000000 +CONFIG_SYS_MEMTEST_END=0xc4000000 +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0x2000000 +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTSTAGE_RECORD_COUNT=100 +CONFIG_BOOTDELAY=3 +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp" +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_SYS_PROMPT="STM32MP> " +# CONFIG_CMD_ELF is not set +CONFIG_CMD_ASKENV=y +# CONFIG_CMD_EXPORTENV is not set +CONFIG_CMD_ERASEENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_UNZIP=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_LSBLK=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CAT=y +CONFIG_CMD_SETEXPR_FMT=y +CONFIG_CMD_XXD=y +CONFIG_CMD_DHCP6=y +CONFIG_CMD_TFTPPUT=y +CONFIG_SYS_DISABLE_AUTOLOAD=y +CONFIG_CMD_WGET=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_RNG=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_BTRFS=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_LOG=y +CONFIG_CMD_UBI=y +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_LIVE=y +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_SPI_MAX_HZ=50000000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_VERSION_VARIABLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_IP_DEFRAG=y +CONFIG_TFTP_TSIZE=y +CONFIG_PROT_TCP_SACK=y +CONFIG_IPV6=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_BOOTCOUNT_MAGIC=0xB0C40000 +CONFIG_CLK_SCMI=y +CONFIG_SET_DFU_ALT_INFO=y +CONFIG_GPIO_HOG=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_STM32F7=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_STM32_FMC2_EBI=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_STM32_SDMMC2=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_REALTEK=y +CONFIG_DWC_ETH_QOS=y +CONFIG_PHY=y +CONFIG_PHY_STM32_USBPHYC=y +CONFIG_PINCONF=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_STPMIC1=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_REGULATOR_STPMIC1=y +CONFIG_DM_REGULATOR_SCMI=y +CONFIG_RESET_SCMI=y +CONFIG_DM_RNG=y +CONFIG_RNG_STM32=y +CONFIG_DM_RTC=y +CONFIG_RTC_STM32=y +CONFIG_SERIAL_RX_BUFFER=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_STM32_QSPI=y +CONFIG_STM32_SPI=y +CONFIG_SYSRESET_PSCI=y +CONFIG_TEE=y +CONFIG_OPTEE=y +# CONFIG_OPTEE_TA_AVB is not set +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_ONBOARD_HUB=y +CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2000 +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="dh" +CONFIG_USB_GADGET_VENDOR_NUM=0x0483 +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720 +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_WDT=y +CONFIG_WDT_STM32MP=y +CONFIG_FAT_WRITE=y +CONFIG_ERRNO_STR=y +# CONFIG_EFI_LOADER is not set diff --git a/drivers/net/dwc_eth_qos_stm32.c b/drivers/net/dwc_eth_qos_stm32.c index fbc08bba1d6..cffaa10b705 100644 --- a/drivers/net/dwc_eth_qos_stm32.c +++ b/drivers/net/dwc_eth_qos_stm32.c @@ -266,6 +266,12 @@ static int eqos_probe_resources_stm32(struct udevice *dev) if (ret) dev_warn(dev, "No phy clock provided %d\n", ret); + /* Get reset gpio pin (optional) */ + ret = gpio_request_by_name(dev, "phy-reset-gpios", 0, + &eqos->phy_reset_gpio, GPIOD_IS_OUT); + if (ret) + pr_warn("No phy reset gpio provided: %d\n", ret); + dev_dbg(dev, "%s: OK\n", __func__); return 0; @@ -277,6 +283,21 @@ err_probe: return ret; } +static int eqos_start_resets_stm32(struct udevice *dev) +{ + struct eqos_priv *eqos = dev_get_priv(dev); + + debug("%s(dev=%p):\n", __func__, dev); + + if (dm_gpio_is_valid(&eqos->phy_reset_gpio)) { + dm_gpio_set_value(&eqos->phy_reset_gpio, 1); + udelay(2); + dm_gpio_set_value(&eqos->phy_reset_gpio, 0); + } + + return 0; +} + static int eqos_remove_resources_stm32(struct udevice *dev) { dev_dbg(dev, "%s:\n", __func__); @@ -292,7 +313,7 @@ static struct eqos_ops eqos_stm32_ops = { .eqos_probe_resources = eqos_probe_resources_stm32, .eqos_remove_resources = eqos_remove_resources_stm32, .eqos_stop_resets = eqos_null_ops, - .eqos_start_resets = eqos_null_ops, + .eqos_start_resets = eqos_start_resets_stm32, .eqos_stop_clks = eqos_stop_clks_stm32, .eqos_start_clks = eqos_start_clks_stm32, .eqos_calibrate_pads = eqos_null_ops, |