diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 60 |
1 files changed, 50 insertions, 10 deletions
@@ -380,6 +380,27 @@ The following options need to be configured: expect it to be in bytes, others in MB. Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes. +- Serial Ports: + CFG_PL010_SERIAL + + Define this if you want support for Amba PrimeCell PL010 UARTs. + + CFG_PL011_SERIAL + + Define this if you want support for Amba PrimeCell PL011 UARTs. + + CONFIG_PL011_CLOCK + + If you have Amba PrimeCell PL011 UARTs, set this variable to + the clock speed of the UARTs. + + CONFIG_PL01x_PORTS + + If you have Amba PrimeCell PL010 or PL011 UARTs on your board, + define this to a list of base addresses for each (supported) + port. See e.g. include/configs/versatile.h + + - Console Interface: Depending on board, define exactly one serial port (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2, @@ -541,22 +562,23 @@ The following options need to be configured: CFG_CMD_ASKENV * ask for env variable CFG_CMD_AUTOSCRIPT Autoscript Support CFG_CMD_BDI bdinfo - CFG_CMD_BEDBUG Include BedBug Debugger + CFG_CMD_BEDBUG * Include BedBug Debugger CFG_CMD_BMP * BMP support + CFG_CMD_BSP * Board specific commands CFG_CMD_BOOTD bootd - CFG_CMD_CACHE icache, dcache + CFG_CMD_CACHE * icache, dcache CFG_CMD_CONSOLE coninfo CFG_CMD_DATE * support for RTC, date/time... - CFG_CMD_DHCP DHCP support + CFG_CMD_DHCP * DHCP support CFG_CMD_DIAG * Diagnostics CFG_CMD_DOC * Disk-On-Chip Support - CFG_CMD_DTT Digital Therm and Thermostat + CFG_CMD_DTT * Digital Therm and Thermostat CFG_CMD_ECHO * echo arguments CFG_CMD_EEPROM * EEPROM read/write support - CFG_CMD_ELF bootelf, bootvx + CFG_CMD_ELF * bootelf, bootvx CFG_CMD_ENV saveenv CFG_CMD_FDC * Floppy Disk Support - CFG_CMD_FAT FAT partition support + CFG_CMD_FAT * FAT partition support CFG_CMD_FDOS * Dos diskette Support CFG_CMD_FLASH flinfo, erase, protect CFG_CMD_FPGA FPGA device initialization support @@ -567,7 +589,7 @@ The following options need to be configured: CFG_CMD_IMLS List all found images CFG_CMD_IMMAP * IMMR dump support CFG_CMD_IRQ * irqinfo - CFG_CMD_ITEST * Integer/string test of 2 values + CFG_CMD_ITEST Integer/string test of 2 values CFG_CMD_JFFS2 * JFFS2 Support CFG_CMD_KGDB * kgdb CFG_CMD_LOADB loadb @@ -575,8 +597,8 @@ The following options need to be configured: CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, loop, loopw, mtest CFG_CMD_MISC Misc functions like sleep etc - CFG_CMD_MMC MMC memory mapped support - CFG_CMD_MII MII utility commands + CFG_CMD_MMC * MMC memory mapped support + CFG_CMD_MII * MII utility commands CFG_CMD_NAND * NAND support CFG_CMD_NET bootp, tftpboot, rarpboot CFG_CMD_PCI * pciinfo @@ -585,7 +607,7 @@ The following options need to be configured: CFG_CMD_PORTIO * Port I/O CFG_CMD_REGINFO * Register dump CFG_CMD_RUN run command in env variable - CFG_CMD_SAVES save S record dump + CFG_CMD_SAVES * save S record dump CFG_CMD_SCSI * SCSI Support CFG_CMD_SDRAM * print SDRAM configuration information CFG_CMD_SETGETDCR Support for DCR Register access (4xx only) @@ -783,6 +805,24 @@ The following options need to be configured: enabled with CFG_CMD_MMC. The MMC driver also works with the FAT fs. This is enabled with CFG_CMD_FAT. +- Journaling Flash filesystem support: + CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE, + CONFIG_JFFS2_NAND_DEV + Define these for a default partition on a NAND device + + CFG_JFFS2_FIRST_SECTOR, + CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS + Define these for a default partition on a NOR device + + CFG_JFFS_CUSTOM_PART + Define this to create an own partition. You have to provide a + function struct part_info* jffs2_part_info(int part_num) + + If you define only one JFFS2 partition you may also want to + #define CFG_JFFS_SINGLE_PART 1 + to disable the command chpart. This is the default when you + have not defined a custom partition + - Keyboard Support: CONFIG_ISA_KEYBOARD |