diff options
Diffstat (limited to 'arch/arm/dts/imx8mm-verdin.dtsi')
| -rw-r--r-- | arch/arm/dts/imx8mm-verdin.dtsi | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/arch/arm/dts/imx8mm-verdin.dtsi b/arch/arm/dts/imx8mm-verdin.dtsi index bcab830c6e9..6f081158714 100644 --- a/arch/arm/dts/imx8mm-verdin.dtsi +++ b/arch/arm/dts/imx8mm-verdin.dtsi @@ -3,8 +3,8 @@ * Copyright 2022 Toradex */ -#include "dt-bindings/phy/phy-imx8-pcie.h" -#include "dt-bindings/pwm/pwm.h" +#include <dt-bindings/phy/phy-imx8-pcie.h> +#include <dt-bindings/pwm/pwm.h> #include "imx8mm.dtsi" / { @@ -56,7 +56,11 @@ hdmi_connector: hdmi-connector { compatible = "hdmi-connector"; ddc-i2c-bus = <&i2c2>; + /* Verdin PWM_3_DSI (SODIMM 19) */ + hpd-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; label = "hdmi"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm_3_dsi_hpd_gpio>; type = "a"; status = "disabled"; }; @@ -95,9 +99,10 @@ compatible = "regulator-fixed"; enable-active-high; gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */ - off-on-delay = <500000>; + off-on-delay-us = <500000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_eth>; + regulator-always-on; regulator-boot-on; regulator-max-microvolt = <3300000>; regulator-min-microvolt = <3300000>; @@ -134,7 +139,7 @@ enable-active-high; /* Verdin SD_1_PWR_EN (SODIMM 76) */ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; - off-on-delay = <100000>; + off-on-delay-us = <100000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2_pwr_en>; regulator-max-microvolt = <3300000>; @@ -183,15 +188,15 @@ ddrc_opp_table: opp-table { compatible = "operating-points-v2"; - opp-25M { + opp-25000000 { opp-hz = /bits/ 64 <25000000>; }; - opp-100M { + opp-100000000 { opp-hz = /bits/ 64 <100000000>; }; - opp-750M { + opp-750000000 { opp-hz = /bits/ 64 <750000000>; }; }; @@ -358,7 +363,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pmic>; reg = <0x25>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC @@ -598,7 +602,7 @@ hdmi_lontium_lt8912: hdmi@48 { compatible = "lontium,lt8912b"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>; + pinctrl-0 = <&pinctrl_gpio_10_dsi>; reg = <0x48>; /* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */ /* Verdin GPIO_10_DSI (SODIMM 21) */ @@ -610,7 +614,7 @@ compatible = "atmel,maxtouch"; /* * Verdin GPIO_9_DSI - * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI83 IRQ albeit currently unused) + * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI84 IRQ albeit currently unused) */ interrupt-parent = <&gpio3>; interrupts = <15 IRQ_TYPE_EDGE_FALLING>; @@ -653,9 +657,6 @@ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; assigned-clock-rates = <10000000>, <250000000>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&clk IMX8MM_CLK_PCIE1_PHY>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; /* PCIE_1_RESET# (SODIMM 244) */ @@ -664,6 +665,7 @@ &pcie_phy { clocks = <&clk IMX8MM_CLK_PCIE1_PHY>; + clock-names = "ref"; fsl,clkreq-unsupported; fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>; fsl,tx-deemph-gen1 = <0x2d>; @@ -739,7 +741,6 @@ adp-disable; dr_mode = "otg"; hnp-disable; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; srp-disable; @@ -749,7 +750,6 @@ /* Verdin USB_2 */ &usbotg2 { dr_mode = "host"; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; vbus-supply = <®_usb_otg2_vbus>; |