diff options
Diffstat (limited to 'arch/arm/mach-imx/mx6/soc.c')
-rw-r--r-- | arch/arm/mach-imx/mx6/soc.c | 703 |
1 files changed, 703 insertions, 0 deletions
diff --git a/arch/arm/mach-imx/mx6/soc.c b/arch/arm/mach-imx/mx6/soc.c new file mode 100644 index 00000000000..af316735ee8 --- /dev/null +++ b/arch/arm/mach-imx/mx6/soc.c @@ -0,0 +1,703 @@ +/* + * (C) Copyright 2007 + * Sascha Hauer, Pengutronix + * + * (C) Copyright 2009 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <linux/errno.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/clock.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/boot_mode.h> +#include <asm/mach-imx/dma.h> +#include <asm/mach-imx/hab.h> +#include <stdbool.h> +#include <asm/arch/mxc_hdmi.h> +#include <asm/arch/crm_regs.h> +#include <dm.h> +#include <imx_thermal.h> +#include <mmc.h> + +enum ldo_reg { + LDO_ARM, + LDO_SOC, + LDO_PU, +}; + +struct scu_regs { + u32 ctrl; + u32 config; + u32 status; + u32 invalidate; + u32 fpga_rev; +}; + +#if defined(CONFIG_IMX_THERMAL) +static const struct imx_thermal_plat imx6_thermal_plat = { + .regs = (void *)ANATOP_BASE_ADDR, + .fuse_bank = 1, + .fuse_word = 6, +}; + +U_BOOT_DEVICE(imx6_thermal) = { + .name = "imx_thermal", + .platdata = &imx6_thermal_plat, +}; +#endif + +#if defined(CONFIG_SECURE_BOOT) +struct imx_sec_config_fuse_t const imx_sec_config_fuse = { + .bank = 0, + .word = 6, +}; +#endif + +u32 get_nr_cpus(void) +{ + struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; + return readl(&scu->config) & 3; +} + +u32 get_cpu_rev(void) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + u32 reg = readl(&anatop->digprog_sololite); + u32 type = ((reg >> 16) & 0xff); + u32 major, cfg = 0; + + if (type != MXC_CPU_MX6SL) { + reg = readl(&anatop->digprog); + struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; + cfg = readl(&scu->config) & 3; + type = ((reg >> 16) & 0xff); + if (type == MXC_CPU_MX6DL) { + if (!cfg) + type = MXC_CPU_MX6SOLO; + } + + if (type == MXC_CPU_MX6Q) { + if (cfg == 1) + type = MXC_CPU_MX6D; + } + + } + major = ((reg >> 8) & 0xff); + if ((major >= 1) && + ((type == MXC_CPU_MX6Q) || (type == MXC_CPU_MX6D))) { + major--; + type = MXC_CPU_MX6QP; + if (cfg == 1) + type = MXC_CPU_MX6DP; + } + reg &= 0xff; /* mx6 silicon revision */ + return (type << 12) | (reg + (0x10 * (major + 1))); +} + +/* + * OCOTP_CFG3[17:16] (see Fusemap Description Table offset 0x440) + * defines a 2-bit SPEED_GRADING + */ +#define OCOTP_CFG3_SPEED_SHIFT 16 +#define OCOTP_CFG3_SPEED_800MHZ 0 +#define OCOTP_CFG3_SPEED_850MHZ 1 +#define OCOTP_CFG3_SPEED_1GHZ 2 +#define OCOTP_CFG3_SPEED_1P2GHZ 3 + +/* + * For i.MX6UL + */ +#define OCOTP_CFG3_SPEED_528MHZ 1 +#define OCOTP_CFG3_SPEED_696MHZ 2 + +u32 get_cpu_speed_grade_hz(void) +{ + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; + struct fuse_bank *bank = &ocotp->bank[0]; + struct fuse_bank0_regs *fuse = + (struct fuse_bank0_regs *)bank->fuse_regs; + uint32_t val; + + val = readl(&fuse->cfg3); + val >>= OCOTP_CFG3_SPEED_SHIFT; + val &= 0x3; + + if (is_mx6ul() || is_mx6ull()) { + if (val == OCOTP_CFG3_SPEED_528MHZ) + return 528000000; + else if (val == OCOTP_CFG3_SPEED_696MHZ) + return 69600000; + else + return 0; + } + + switch (val) { + /* Valid for IMX6DQ */ + case OCOTP_CFG3_SPEED_1P2GHZ: + if (is_mx6dq() || is_mx6dqp()) + return 1200000000; + /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ + case OCOTP_CFG3_SPEED_1GHZ: + return 996000000; + /* Valid for IMX6DQ */ + case OCOTP_CFG3_SPEED_850MHZ: + if (is_mx6dq() || is_mx6dqp()) + return 852000000; + /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ + case OCOTP_CFG3_SPEED_800MHZ: + return 792000000; + } + return 0; +} + +/* + * OCOTP_MEM0[7:6] (see Fusemap Description Table offset 0x480) + * defines a 2-bit Temperature Grade + * + * return temperature grade and min/max temperature in Celsius + */ +#define OCOTP_MEM0_TEMP_SHIFT 6 + +u32 get_cpu_temp_grade(int *minc, int *maxc) +{ + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; + struct fuse_bank *bank = &ocotp->bank[1]; + struct fuse_bank1_regs *fuse = + (struct fuse_bank1_regs *)bank->fuse_regs; + uint32_t val; + + val = readl(&fuse->mem0); + val >>= OCOTP_MEM0_TEMP_SHIFT; + val &= 0x3; + + if (minc && maxc) { + if (val == TEMP_AUTOMOTIVE) { + *minc = -40; + *maxc = 125; + } else if (val == TEMP_INDUSTRIAL) { + *minc = -40; + *maxc = 105; + } else if (val == TEMP_EXTCOMMERCIAL) { + *minc = -20; + *maxc = 105; + } else { + *minc = 0; + *maxc = 95; + } + } + return val; +} + +#ifdef CONFIG_REVISION_TAG +u32 __weak get_board_rev(void) +{ + u32 cpurev = get_cpu_rev(); + u32 type = ((cpurev >> 12) & 0xff); + if (type == MXC_CPU_MX6SOLO) + cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF); + + if (type == MXC_CPU_MX6D) + cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF); + + return cpurev; +} +#endif + +static void clear_ldo_ramp(void) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + int reg; + + /* ROM may modify LDO ramp up time according to fuse setting, so in + * order to be in the safe side we neeed to reset these settings to + * match the reset value: 0'b00 + */ + reg = readl(&anatop->ana_misc2); + reg &= ~(0x3f << 24); + writel(reg, &anatop->ana_misc2); +} + +/* + * Set the PMU_REG_CORE register + * + * Set LDO_SOC/PU/ARM regulators to the specified millivolt level. + * Possible values are from 0.725V to 1.450V in steps of + * 0.025V (25mV). + */ +static int set_ldo_voltage(enum ldo_reg ldo, u32 mv) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + u32 val, step, old, reg = readl(&anatop->reg_core); + u8 shift; + + if (mv < 725) + val = 0x00; /* Power gated off */ + else if (mv > 1450) + val = 0x1F; /* Power FET switched full on. No regulation */ + else + val = (mv - 700) / 25; + + clear_ldo_ramp(); + + switch (ldo) { + case LDO_SOC: + shift = 18; + break; + case LDO_PU: + shift = 9; + break; + case LDO_ARM: + shift = 0; + break; + default: + return -EINVAL; + } + + old = (reg & (0x1F << shift)) >> shift; + step = abs(val - old); + if (step == 0) + return 0; + + reg = (reg & ~(0x1F << shift)) | (val << shift); + writel(reg, &anatop->reg_core); + + /* + * The LDO ramp-up is based on 64 clock cycles of 24 MHz = 2.6 us per + * step + */ + udelay(3 * step); + + return 0; +} + +static void set_ahb_rate(u32 val) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg, div; + + div = get_periph_clk() / val - 1; + reg = readl(&mxc_ccm->cbcdr); + + writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) | + (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr); +} + +static void clear_mmdc_ch_mask(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg; + reg = readl(&mxc_ccm->ccdr); + + /* Clear MMDC channel mask */ + if (is_mx6sx() || is_mx6ul() || is_mx6ull() || is_mx6sl()) + reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK); + else + reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK); + writel(reg, &mxc_ccm->ccdr); +} + +#define OCOTP_MEM0_REFTOP_TRIM_SHIFT 8 + +static void init_bandgap(void) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; + struct fuse_bank *bank = &ocotp->bank[1]; + struct fuse_bank1_regs *fuse = + (struct fuse_bank1_regs *)bank->fuse_regs; + uint32_t val; + + /* + * Ensure the bandgap has stabilized. + */ + while (!(readl(&anatop->ana_misc0) & 0x80)) + ; + /* + * For best noise performance of the analog blocks using the + * outputs of the bandgap, the reftop_selfbiasoff bit should + * be set. + */ + writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set); + /* + * On i.MX6ULL,we need to set VBGADJ bits according to the + * REFTOP_TRIM[3:0] in fuse table + * 000 - set REFTOP_VBGADJ[2:0] to 3b'110, + * 110 - set REFTOP_VBGADJ[2:0] to 3b'000, + * 001 - set REFTOP_VBGADJ[2:0] to 3b'001, + * 010 - set REFTOP_VBGADJ[2:0] to 3b'010, + * 011 - set REFTOP_VBGADJ[2:0] to 3b'011, + * 100 - set REFTOP_VBGADJ[2:0] to 3b'100, + * 101 - set REFTOP_VBGADJ[2:0] to 3b'101, + * 111 - set REFTOP_VBGADJ[2:0] to 3b'111, + */ + if (is_mx6ull()) { + val = readl(&fuse->mem0); + val >>= OCOTP_MEM0_REFTOP_TRIM_SHIFT; + val &= 0x7; + + writel(val << BM_ANADIG_ANA_MISC0_REFTOP_VBGADJ_SHIFT, + &anatop->ana_misc0_set); + } +} + +#ifdef CONFIG_MX6SL +static void set_preclk_from_osc(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 reg; + + reg = readl(&mxc_ccm->cscmr1); + reg |= MXC_CCM_CSCMR1_PER_CLK_SEL_MASK; + writel(reg, &mxc_ccm->cscmr1); +} +#endif + +int arch_cpu_init(void) +{ + init_aips(); + + /* Need to clear MMDC_CHx_MASK to make warm reset work. */ + clear_mmdc_ch_mask(); + + /* + * Disable self-bias circuit in the analog bandap. + * The self-bias circuit is used by the bandgap during startup. + * This bit should be set after the bandgap has initialized. + */ + init_bandgap(); + + if (!is_mx6ul() && !is_mx6ull()) { + /* + * When low freq boot is enabled, ROM will not set AHB + * freq, so we need to ensure AHB freq is 132MHz in such + * scenario. + * + * To i.MX6UL, when power up, default ARM core and + * AHB rate is 396M and 132M. + */ + if (mxc_get_clock(MXC_ARM_CLK) == 396000000) + set_ahb_rate(132000000); + } + + if (is_mx6ul()) { + if (is_soc_rev(CHIP_REV_1_0) == 0) { + /* + * According to the design team's requirement on + * i.MX6UL,the PMIC_STBY_REQ PAD should be configured + * as open drain 100K (0x0000b8a0). + * Only exists on TO1.0 + */ + writel(0x0000b8a0, IOMUXC_BASE_ADDR + 0x29c); + } else { + /* + * From TO1.1, SNVS adds internal pull up control + * for POR_B, the register filed is GPBIT[1:0], + * after system boot up, it can be set to 2b'01 + * to disable internal pull up.It can save about + * 30uA power in SNVS mode. + */ + writel((readl(MX6UL_SNVS_LP_BASE_ADDR + 0x10) & + (~0x1400)) | 0x400, + MX6UL_SNVS_LP_BASE_ADDR + 0x10); + } + } + + if (is_mx6ull()) { + /* + * GPBIT[1:0] is suggested to set to 2'b11: + * 2'b00 : always PUP100K + * 2'b01 : PUP100K when PMIC_ON_REQ or SOC_NOT_FAIL + * 2'b10 : always disable PUP100K + * 2'b11 : PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL + * register offset is different from i.MX6UL, since + * i.MX6UL is fixed by ECO. + */ + writel(readl(MX6UL_SNVS_LP_BASE_ADDR) | + 0x3, MX6UL_SNVS_LP_BASE_ADDR); + } + + /* Set perclk to source from OSC 24MHz */ +#if defined(CONFIG_MX6SL) + set_preclk_from_osc(); +#endif + + imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */ + + init_src(); + + return 0; +} + +#ifdef CONFIG_ENV_IS_IN_MMC +__weak int board_mmc_get_env_dev(int devno) +{ + return CONFIG_SYS_MMC_ENV_DEV; +} + +static int mmc_get_boot_dev(void) +{ + struct src *src_regs = (struct src *)SRC_BASE_ADDR; + u32 soc_sbmr = readl(&src_regs->sbmr1); + u32 bootsel; + int devno; + + /* + * Refer to + * "i.MX 6Dual/6Quad Applications Processor Reference Manual" + * Chapter "8.5.3.1 Expansion Device eFUSE Configuration" + * i.MX6SL/SX/UL has same layout. + */ + bootsel = (soc_sbmr & 0x000000FF) >> 6; + + /* No boot from sd/mmc */ + if (bootsel != 1) + return -1; + + /* BOOT_CFG2[3] and BOOT_CFG2[4] */ + devno = (soc_sbmr & 0x00001800) >> 11; + + return devno; +} + +int mmc_get_env_dev(void) +{ + int devno = mmc_get_boot_dev(); + + /* If not boot from sd/mmc, use default value */ + if (devno < 0) + return CONFIG_SYS_MMC_ENV_DEV; + + return board_mmc_get_env_dev(devno); +} + +#ifdef CONFIG_SYS_MMC_ENV_PART +__weak int board_mmc_get_env_part(int devno) +{ + return CONFIG_SYS_MMC_ENV_PART; +} + +uint mmc_get_env_part(struct mmc *mmc) +{ + int devno = mmc_get_boot_dev(); + + /* If not boot from sd/mmc, use default value */ + if (devno < 0) + return CONFIG_SYS_MMC_ENV_PART; + + return board_mmc_get_env_part(devno); +} +#endif +#endif + +int board_postclk_init(void) +{ + set_ldo_voltage(LDO_SOC, 1175); /* Set VDDSOC to 1.175V */ + + return 0; +} + +#if defined(CONFIG_FEC_MXC) +void imx_get_mac_from_fuse(int dev_id, unsigned char *mac) +{ + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; + struct fuse_bank *bank = &ocotp->bank[4]; + struct fuse_bank4_regs *fuse = + (struct fuse_bank4_regs *)bank->fuse_regs; + + if ((is_mx6sx() || is_mx6ul() || is_mx6ull()) && dev_id == 1) { + u32 value = readl(&fuse->mac_addr2); + mac[0] = value >> 24 ; + mac[1] = value >> 16 ; + mac[2] = value >> 8 ; + mac[3] = value ; + + value = readl(&fuse->mac_addr1); + mac[4] = value >> 24 ; + mac[5] = value >> 16 ; + + } else { + u32 value = readl(&fuse->mac_addr1); + mac[0] = (value >> 8); + mac[1] = value ; + + value = readl(&fuse->mac_addr0); + mac[2] = value >> 24 ; + mac[3] = value >> 16 ; + mac[4] = value >> 8 ; + mac[5] = value ; + } + +} +#endif + +/* + * cfg_val will be used for + * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0] + * After reset, if GPR10[28] is 1, ROM will use GPR9[25:0] + * instead of SBMR1 to determine the boot device. + */ +const struct boot_mode soc_boot_modes[] = { + {"normal", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)}, + /* reserved value should start rom usb */ +#if defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL) + {"usb", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)}, +#else + {"usb", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, +#endif + {"sata", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)}, + {"ecspi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)}, + {"ecspi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)}, + {"ecspi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)}, + {"ecspi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)}, + /* 4 bit bus width */ + {"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)}, + {"esdhc2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, + {"esdhc3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, + {"esdhc4", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {NULL, 0}, +}; + +void reset_misc(void) +{ +#ifdef CONFIG_VIDEO_MXS + lcdif_power_down(); +#endif +} + +void s_init(void) +{ + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + u32 mask480; + u32 mask528; + u32 reg, periph1, periph2; + + if (is_mx6sx() || is_mx6ul() || is_mx6ull()) + return; + + /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs + * to make sure PFD is working right, otherwise, PFDs may + * not output clock after reset, MX6DL and MX6SL have added 396M pfd + * workaround in ROM code, as bus clock need it + */ + + mask480 = ANATOP_PFD_CLKGATE_MASK(0) | + ANATOP_PFD_CLKGATE_MASK(1) | + ANATOP_PFD_CLKGATE_MASK(2) | + ANATOP_PFD_CLKGATE_MASK(3); + mask528 = ANATOP_PFD_CLKGATE_MASK(1) | + ANATOP_PFD_CLKGATE_MASK(3); + + reg = readl(&ccm->cbcmr); + periph2 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK) + >> MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET); + periph1 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK) + >> MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET); + + /* Checking if PLL2 PFD0 or PLL2 PFD2 is using for periph clock */ + if ((periph2 != 0x2) && (periph1 != 0x2)) + mask528 |= ANATOP_PFD_CLKGATE_MASK(0); + + if ((periph2 != 0x1) && (periph1 != 0x1) && + (periph2 != 0x3) && (periph1 != 0x3)) + mask528 |= ANATOP_PFD_CLKGATE_MASK(2); + + writel(mask480, &anatop->pfd_480_set); + writel(mask528, &anatop->pfd_528_set); + writel(mask480, &anatop->pfd_480_clr); + writel(mask528, &anatop->pfd_528_clr); +} + +#ifdef CONFIG_IMX_HDMI +void imx_enable_hdmi_phy(void) +{ + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + u8 reg; + reg = readb(&hdmi->phy_conf0); + reg |= HDMI_PHY_CONF0_PDZ_MASK; + writeb(reg, &hdmi->phy_conf0); + udelay(3000); + reg |= HDMI_PHY_CONF0_ENTMDS_MASK; + writeb(reg, &hdmi->phy_conf0); + udelay(3000); + reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; + writeb(reg, &hdmi->phy_conf0); + writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); +} + +void imx_setup_hdmi(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + int reg, count; + u8 val; + + /* Turn on HDMI PHY clock */ + reg = readl(&mxc_ccm->CCGR2); + reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK| + MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; + writel(reg, &mxc_ccm->CCGR2); + writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); + reg = readl(&mxc_ccm->chsccdr); + reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK| + MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK| + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); + reg |= (CHSCCDR_PODF_DIVIDE_BY_3 + << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) + |(CHSCCDR_IPU_PRE_CLK_540M_PFD + << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); + writel(reg, &mxc_ccm->chsccdr); + + /* Clear the overflow condition */ + if (readb(&hdmi->ih_fc_stat2) & HDMI_IH_FC_STAT2_OVERFLOW_MASK) { + /* TMDS software reset */ + writeb((u8)~HDMI_MC_SWRSTZ_TMDSSWRST_REQ, &hdmi->mc_swrstz); + val = readb(&hdmi->fc_invidconf); + /* Need minimum 3 times to write to clear the register */ + for (count = 0 ; count < 5 ; count++) + writeb(val, &hdmi->fc_invidconf); + } +} +#endif + +#ifdef CONFIG_IMX_BOOTAUX +int arch_auxiliary_core_up(u32 core_id, u32 boot_private_data) +{ + struct src *src_reg; + u32 stack, pc; + + if (!boot_private_data) + return -EINVAL; + + stack = *(u32 *)boot_private_data; + pc = *(u32 *)(boot_private_data + 4); + + /* Set the stack and pc to M4 bootROM */ + writel(stack, M4_BOOTROM_BASE_ADDR); + writel(pc, M4_BOOTROM_BASE_ADDR + 4); + + /* Enable M4 */ + src_reg = (struct src *)SRC_BASE_ADDR; + clrsetbits_le32(&src_reg->scr, SRC_SCR_M4C_NON_SCLR_RST_MASK, + SRC_SCR_M4_ENABLE_MASK); + + return 0; +} + +int arch_auxiliary_core_check_up(u32 core_id) +{ + struct src *src_reg = (struct src *)SRC_BASE_ADDR; + unsigned val; + + val = readl(&src_reg->scr); + + if (val & SRC_SCR_M4C_NON_SCLR_RST_MASK) + return 0; /* assert in reset */ + + return 1; +} +#endif |