diff options
Diffstat (limited to 'arch/arm/mach-sunxi/Kconfig')
| -rw-r--r-- | arch/arm/mach-sunxi/Kconfig | 60 |
1 files changed, 43 insertions, 17 deletions
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig index 9d5df2c1027..a4a8d8e9445 100644 --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -85,6 +85,12 @@ config DRAM_SUN50I_H616_TPR2 help TPR2 value from vendor DRAM settings. +config DRAM_SUN50I_H616_TPR6 + hex "H616 DRAM TPR6 parameter" + default 0x3300c080 + help + TPR6 value from vendor DRAM settings. + config DRAM_SUN50I_H616_TPR10 hex "H616 DRAM TPR10 parameter" help @@ -121,7 +127,7 @@ config AXP_PMIC_BUS config SUNXI_SRAM_ADDRESS hex default 0x10000 if MACH_SUN9I || MACH_SUN50I || MACH_SUN50I_H5 - default 0x20000 if SUN50I_GEN_H6 + default 0x20000 if SUN50I_GEN_H6 || SUNXI_GEN_NCAT2 default 0x0 ---help--- Older Allwinner SoCs have their mask boot ROM mapped just below 4GB, @@ -183,6 +189,14 @@ config SUN50I_GEN_H6 Select this for sunxi SoCs which have H6 like peripherals, clocks and memory map. +config SUNXI_GEN_NCAT2 + bool + select MMC_SUNXI_HAS_NEW_MODE + select SUPPORT_SPL + ---help--- + Select this for sunxi SoCs which have D1 like peripherals, clocks + and memory map. + config SUNXI_DRAM_DW bool ---help--- @@ -338,6 +352,19 @@ config MACH_SUN8I_R40 select SUNXI_DRAM_DW_32BIT imply SPL_SYS_I2C_LEGACY +config MACH_SUN8I_R528 + bool "sun8i (Allwinner R528)" + select CPU_V7A + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SPL_ARMV7_SET_CORTEX_SMPEN + select SUNXI_GEN_NCAT2 + select SUNXI_NEW_PINCTRL + select MMC_SUNXI_HAS_NEW_MODE + select SUPPORT_SPL + select DRAM_SUN20I_D1 + config MACH_SUN8I_V3S bool "sun8i (Allwinner V3/V3s/S3/S3L)" select CPU_V7A @@ -441,6 +468,9 @@ config SUNXI_DRAM_DDR2 config SUNXI_DRAM_LPDDR3 bool +config SUNXI_DRAM_LPDDR4 + bool + choice prompt "DRAM Type and Timing" default SUNXI_DRAM_DDR3_1333 if !MACH_SUN8I_V3S @@ -484,6 +514,14 @@ config SUNXI_DRAM_H616_LPDDR3 This option is the LPDDR3 timing used by the stock boot0 by Allwinner. +config SUNXI_DRAM_H616_LPDDR4 + bool "LPDDR4 DRAM chips on the H616 DRAM controller" + select SUNXI_DRAM_LPDDR4 + depends on DRAM_SUN50I_H616 + help + This option is the LPDDR4 timing used by the stock boot0 by + Allwinner. + config SUNXI_DRAM_H616_DDR3_1333 bool "DDR3-1333 boot0 timings on the H616 DRAM controller" select SUNXI_DRAM_DDR3 @@ -648,6 +686,7 @@ config SYS_CLK_FREQ default 1008000000 if MACH_SUN9I default 888000000 if MACH_SUN50I_H6 default 1008000000 if MACH_SUN50I_H616 + default 1008000000 if MACH_SUN8I_R528 config SYS_CONFIG_NAME default "suniv" if MACH_SUNIV @@ -656,6 +695,7 @@ config SYS_CONFIG_NAME default "sun6i" if MACH_SUN6I default "sun7i" if MACH_SUN7I default "sun8i" if MACH_SUN8I + default "sun8i" if MACH_SUN8I_R528 default "sun9i" if MACH_SUN9I default "sun50i" if MACH_SUN50I default "sun50i" if MACH_SUN50I_H6 @@ -695,13 +735,6 @@ config OLD_SUNXI_KERNEL_COMPAT Set this to enable various workarounds for old kernels, this results in sub-optimal settings for newer kernels, only enable if needed. -config MACPWR - string "MAC power pin" - default "" - help - Set the pin used to power the MAC. This takes a string in the format - understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - config MMC1_PINS_PH bool "Pins for mmc1 are on Port H" depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40 @@ -795,7 +828,6 @@ config AXP_GPIO config AXP_DISABLE_BOOT_ON_POWERON bool "Disable device boot on power plug-in" depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER - default n ---help--- Say Y here to prevent the device from booting up because of a plug-in event. When set, the device will boot into the SPL briefly to @@ -811,6 +843,7 @@ config VIDEO_SUNXI depends on !MACH_SUN9I depends on !MACH_SUN50I depends on !SUN50I_GEN_H6 + depends on !SUNXI_GEN_NCAT2 select VIDEO select DISPLAY imply VIDEO_DT_SIMPLEFB @@ -1008,14 +1041,6 @@ config VIDEO_LCD_TL059WV5C0 endchoice -config SATAPWR - string "SATA power pin" - default "" - help - Set the pins used to power the SATA. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of - port H. - config GMAC_TX_DELAY int "GMAC Transmit Clock Delay Chain" default 0 @@ -1032,6 +1057,7 @@ config SPL_STACK_R_ADDR default 0x2fe00000 if MACH_SUN9I default 0x4fe00000 if MACH_SUN50I default 0x4fe00000 if SUN50I_GEN_H6 + default 0x4fe00000 if SUNXI_GEN_NCAT2 config SPL_SPI_SUNXI bool "Support for SPI Flash on Allwinner SoCs in SPL" |