diff options
Diffstat (limited to 'board/bmw')
-rw-r--r-- | board/bmw/Makefile | 2 | ||||
-rw-r--r-- | board/bmw/README | 41 | ||||
-rw-r--r-- | board/bmw/bmw.c | 3 | ||||
-rw-r--r-- | board/bmw/bmw.h | 4 | ||||
-rw-r--r-- | board/bmw/config.mk | 4 | ||||
-rw-r--r-- | board/bmw/early_init.S | 560 | ||||
-rw-r--r-- | board/bmw/flash.c | 426 | ||||
-rw-r--r-- | board/bmw/m48t59y.c | 1 | ||||
-rw-r--r-- | board/bmw/ns16550.c | 3 | ||||
-rw-r--r-- | board/bmw/ns16550.h | 1 | ||||
-rw-r--r-- | board/bmw/u-boot.lds | 6 |
11 files changed, 517 insertions, 534 deletions
diff --git a/board/bmw/Makefile b/board/bmw/Makefile index 46fe7910e74..621640b0079 100644 --- a/board/bmw/Makefile +++ b/board/bmw/Makefile @@ -31,7 +31,7 @@ OBJS = $(BOARD).o flash.o ns16550.o serial.o m48t59y.o SOBJS = early_init.o $(LIB): .depend $(OBJS) $(SOBJS) - $(AR) crv $@ $^ + $(AR) crv $@ $(OBJS) $(SOBJS) ######################################################################### diff --git a/board/bmw/README b/board/bmw/README index 55ef56ebe1b..70bc81362f1 100644 --- a/board/bmw/README +++ b/board/bmw/README @@ -20,39 +20,39 @@ BMW uses the MPC8245 CHRP Address MAP B found in the MPC8245 Users Manual onboard the processor module are listed briefly below: 0x00000000 - 0x40000000 - 64MB SDRAM SIMM - (Unregistered PC-100 SDRAM DIMM Module) + (Unregistered PC-100 SDRAM DIMM Module) 0xFF000000 - 0xFF001FFF - M-Systems DiskOnChip (TM) 2000 - TSOP 16MB (MD2211-D16-V3) + TSOP 16MB (MD2211-D16-V3) 0x70000000 - 0x70001FFF - M-Systems DiskOnChip (TM) 2000 - DIP32 (Socketed 16MB - 1GB ) * - NOTE: this is not populated on all systems. + DIP32 (Socketed 16MB - 1GB ) * + NOTE: this is not populated on all systems. 0x7c000000 - 0x7c000000 - Reset Register - (Write 0 to reset) + (Write 0 to reset) 0x7c000001 - 0x7c000001 - System LED - (Clear Bit 7 to turn on, set to shut off) + (Clear Bit 7 to turn on, set to shut off) 0x7c000002 - 0x7c000002 - M48T59 Watchdog IRQ3 - (Clear bit 7 to reset, set to assert IRQ3) + (Clear bit 7 to reset, set to assert IRQ3) 0x7c000003 - 0x7c000003 - M48T59 Write-Protect Register - (Clear bit 7 to make R/W, set to make R/O) + (Clear bit 7 to make R/W, set to make R/O) 0x7c002000 - 0x7c002003 - Infineon OSRAM DLR2416 4 Character - 5x7 Dot Matrix Alphanumeric Display - (Each byte sets the appropriate character) + 5x7 Dot Matrix Alphanumeric Display + (Each byte sets the appropriate character) 0x7c004000 - 0x7c005FF0 - SGS-THOMSON M48T59Y 8K NVRAM/RTC - NVRAM Memory Region + NVRAM Memory Region 0x7c005FF0 - 0x7c005FFF - SGS-THOMSON M48T59Y 8K NVRAM/RTC - Realtime Clock Registers + Realtime Clock Registers 0xFFF00000 - 0xFFF80000 - 512K PLCC32 BootRom - (AMD AM29F040, ST 29W040B) + (AMD AM29F040, ST 29W040B) 0xFFF00100 - System Reset Vector @@ -131,7 +131,6 @@ Supported features: - DOC Support - (underway) - U-Boot 1.2.0 (Aug 6 2002 - 17:44:48) CPU: MPC8245 Revision 16.20 at 264 MHz: 16 kB I-Cache 16 kB D-Cache @@ -167,15 +166,10 @@ Environment size: 315/8172 bytes =>boot - - - - - DevTools ======== ELDK - DENX Embedded Linux Development Kit + DENX Embedded Linux Development Kit ROM Emulator Grammar Engine PROMICE P1160-90-AI21E (2MBx8bit, 90ns access time) @@ -187,7 +181,6 @@ ICE WRS/EST VisionICE-II (PPC8240) - =>reset @@ -216,8 +209,8 @@ TFTP from server 172.16.40.111; our IP address is 172.16.40.114 Filename 'vmlinux.img'. Load address: 0x100000 Loading: ################################################################# - ####################################T ############################# - ###################### + ####################################T ############################# + ###################### done Bytes transferred = 777199 (bdbef hex) @@ -317,7 +310,6 @@ Welcome to Linux/PPC MPC8245/BMW - switch-2 login: root Password: PAM_unix[49]: (login) session opened for user root by LOGIN(uid=0) @@ -328,7 +320,6 @@ Welcome to Linux/PPC MPC8245/BMW - login[49]: ROOT LOGIN on `console' root@switch-2:~# cat /proc/cpuinfo diff --git a/board/bmw/bmw.c b/board/bmw/bmw.c index 26856621e7f..f2d33fc1536 100644 --- a/board/bmw/bmw.c +++ b/board/bmw/bmw.c @@ -94,9 +94,6 @@ int misc_init_f (void) } - - - /* * Initialize PCI Devices, report devices found. */ diff --git a/board/bmw/bmw.h b/board/bmw/bmw.h index 6b7571c121c..dd975693031 100644 --- a/board/bmw/bmw.h +++ b/board/bmw/bmw.h @@ -46,13 +46,13 @@ #define LED_REG_BASE (XROM_BASE_ADDR | 0x2000) #define TOD_BASE (XROM_BASE_ADDR | 0x4000) #define LED_REG(x) (*(volatile unsigned char *) \ - (LED_REG_BASE + (x))) + (LED_REG_BASE + (x))) #define XROM_DEV_SIZE 0x00006000 #define ENET_DEV_BASE 0x80000000 #define PLD_REG(off) (*(volatile unsigned char *)\ - (PLD_REG_BASE + (off))) + (PLD_REG_BASE + (off))) #define PLD_REVID_B1 0x7f /* Fix me */ #define PLD_REVID_B2 0x01 /* Fix me */ diff --git a/board/bmw/config.mk b/board/bmw/config.mk index 7facadf22ad..f9915496ada 100644 --- a/board/bmw/config.mk +++ b/board/bmw/config.mk @@ -28,5 +28,5 @@ TEXT_BASE = 0xFFF00000 # NOTE: The flags below affect how the BCM570x driver is compiled PLATFORM_CPPFLAGS += -DEMBEDDED -DBIG_ENDIAN_HOST -DINCLUDE_5701_AX_FIX=1\ - -DDBG=0 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256\ - -DTEXT_BASE=$(TEXT_BASE) + -DDBG=0 -DT3_JUMBO_RCV_RCB_ENTRY_COUNT=256\ + -DTEXT_BASE=$(TEXT_BASE) diff --git a/board/bmw/early_init.S b/board/bmw/early_init.S index ec20a67a713..e6400c30884 100644 --- a/board/bmw/early_init.S +++ b/board/bmw/early_init.S @@ -16,7 +16,7 @@ .global iommu_setup /* Initialize IO/MMU mappings via BAT method Ch. 7, * PPC Programming Reference - */ + */ iommu_setup: /* initialize the BAT registers (SPRs 528 - 543 */ @@ -64,7 +64,7 @@ iommu_setup: BAT marked valid that is in an unknown or transient state */ - addis r5,0,0x0000 + addis r5,0,0x0000 mtibat0u(r5) mtibat0l(r5) mtibat1u(r5) @@ -81,106 +81,106 @@ iommu_setup: mtdbat2l(r5) mtdbat3u(r5) mtdbat3l(r5) - isync + isync /* * Set up I/D BAT0 */ - lis r4, CFG_DBAT0L@h - ori r4, r4, CFG_DBAT0L@l - lis r3, CFG_DBAT0U@h - ori r3, r3, CFG_DBAT0U@l - - mtdbat0l(r4) - isync - mtdbat0u(r3) - isync - sync - - lis r4, CFG_IBAT0L@h - ori r4, r4, CFG_IBAT0L@l - lis r3, CFG_IBAT0U@h - ori r3, r3, CFG_IBAT0U@l - - isync - mtibat0l(r4) - isync + lis r4, CFG_DBAT0L@h + ori r4, r4, CFG_DBAT0L@l + lis r3, CFG_DBAT0U@h + ori r3, r3, CFG_DBAT0U@l + + mtdbat0l(r4) + isync + mtdbat0u(r3) + isync + sync + + lis r4, CFG_IBAT0L@h + ori r4, r4, CFG_IBAT0L@l + lis r3, CFG_IBAT0U@h + ori r3, r3, CFG_IBAT0U@l + + isync + mtibat0l(r4) + isync mtibat0u(r3) - isync + isync /* * Set up I/D BAT1 */ - lis r4, CFG_IBAT1L@h - ori r4, r4, CFG_IBAT1L@l - lis r3, CFG_IBAT1U@h - ori r3, r3, CFG_IBAT1U@l - - isync - mtibat1l(r4) - isync - mtibat1u(r3) - isync - mtdbat1l(r4) - isync - mtdbat1u(r3) - isync - sync + lis r4, CFG_IBAT1L@h + ori r4, r4, CFG_IBAT1L@l + lis r3, CFG_IBAT1U@h + ori r3, r3, CFG_IBAT1U@l + + isync + mtibat1l(r4) + isync + mtibat1u(r3) + isync + mtdbat1l(r4) + isync + mtdbat1u(r3) + isync + sync /* * Set up I/D BAT2 */ - lis r4, CFG_IBAT2L@h - ori r4, r4, CFG_IBAT2L@l - lis r3, CFG_IBAT2U@h - ori r3, r3, CFG_IBAT2U@l - - isync - mtibat2l(r4) - isync - mtibat2u(r3) - isync - mtdbat2l(r4) - isync - mtdbat2u(r3) - isync - sync + lis r4, CFG_IBAT2L@h + ori r4, r4, CFG_IBAT2L@l + lis r3, CFG_IBAT2U@h + ori r3, r3, CFG_IBAT2U@l + + isync + mtibat2l(r4) + isync + mtibat2u(r3) + isync + mtdbat2l(r4) + isync + mtdbat2u(r3) + isync + sync /* * Setup I/D BAT3 */ - lis r4, CFG_IBAT3L@h - ori r4, r4, CFG_IBAT3L@l - lis r3, CFG_IBAT3U@h - ori r3, r3, CFG_IBAT3U@l - - isync - mtibat3l(r4) - isync - mtibat3u(r3) - isync - mtdbat3l(r4) - isync - mtdbat3u(r3) - isync - sync + lis r4, CFG_IBAT3L@h + ori r4, r4, CFG_IBAT3L@l + lis r3, CFG_IBAT3U@h + ori r3, r3, CFG_IBAT3U@l + + isync + mtibat3l(r4) + isync + mtibat3u(r3) + isync + mtdbat3l(r4) + isync + mtdbat3u(r3) + isync + sync /* * Invalidate all 64 TLB's */ - lis r3, 0 - mtctr r3 - lis r5, 4 + lis r3, 0 + mtctr r3 + lis r5, 4 tlblp: - tlbie r3 - sync - addi r3, r3, 0x1000 - cmplw r3, r5 - blt tlblp + tlbie r3 + sync + addi r3, r3, 0x1000 + cmplw r3, r5 + blt tlblp - sync + sync /* * Enable Data Translation @@ -193,7 +193,7 @@ tlblp: isync sync - blr + blr #ifdef USE_V2_INIT @@ -213,8 +213,8 @@ early_init_f: /* MPC8245/BMW CPCI System Init * Jimmy Blair, Broadcom Corp, 2002. */ - mflr r11 - /* Zero-out registers */ + mflr r11 + /* Zero-out registers */ addis r0,r0,0 mtspr SPRG0,r0 @@ -244,7 +244,7 @@ early_init_f: /* Set MPU/MSR to a known state. Turn off FP */ #if 1 /* Turn off floating point (remove to keep FP on) */ - andi. r3, r3, 0 + andi. r3, r3, 0 sync mtmsr r3 isync @@ -368,10 +368,10 @@ instCacheOn603: rlwinm r3, r4, 0, 21, 19 /* clear the ICFI bit */ /* - * The setting of the instruction cache enable (ICE) bit must be - * preceded by an isync instruction to prevent the cache from being - * enabled or disabled while an instruction access is in progress. - */ + * The setting of the instruction cache enable (ICE) bit must be + * preceded by an isync instruction to prevent the cache from being + * enabled or disabled while an instruction access is in progress. + */ isync writeReg4: mtspr HID0, r4 /* Enable Instr Cache & Inval cache */ @@ -397,13 +397,13 @@ cacheEnableDone: cmp 0,0,r3,r7 beq cr0, X4_KAHLUA_START - /* It's not an 8240, is it an 8245? */ + /* It's not an 8240, is it an 8245? */ LOADPTR (r7, KAHLUA2_ID) /* Kahlua PCI controller ID */ cmp 0,0,r3,r7 beq cr0, X4_KAHLUA_START - /* Save the PCI controller type in r7 */ + /* Save the PCI controller type in r7 */ mr r7, r3 LOADPTR (r5, PREP_REG_ADDR) @@ -433,33 +433,33 @@ X4_KAHLUA_START: LOADPTR (r3, PROC_INT2_ADR) /* Processor I/F Config 2 reg. */ stwbrx r3,0,r5 - lis r4, 0x2000 /* Flush PCI config writes */ + lis r4, 0x2000 /* Flush PCI config writes */ stwbrx r4,0,r6 LOADPTR (r9, KAHLUA2_ID) - cmpl 0, 0, r7, r9 - bne L1not8245 + cmpl 0, 0, r7, r9 + bne L1not8245 - /* MIOCR1 -- turn on bit for DLL delay */ + /* MIOCR1 -- turn on bit for DLL delay */ LOADPTR (r3, MIOCR1_ADR_X) stwbrx r3,0,r5 - li r4, 0x04 + li r4, 0x04 stb r4, MIOCR1_SHIFT(r6) - /* For the MPC8245, set register 77 to %00100000 (see Errata #15) */ - /* SDRAM_CLK_DEL (0x77)*/ + /* For the MPC8245, set register 77 to %00100000 (see Errata #15) */ + /* SDRAM_CLK_DEL (0x77)*/ LOADPTR (r3, MIOCR2_ADR_X) stwbrx r3,0,r5 - li r4, 0x10 + li r4, 0x10 stb r4, MIOCR2_SHIFT(r6) - /* PMCR2 -- set PCI hold delay to <10>b for 33 MHz */ + /* PMCR2 -- set PCI hold delay to <10>b for 33 MHz */ LOADPTR (r3, PMCR2_ADR_X) stwbrx r3,0,r5 - li r4, 0x20 + li r4, 0x20 stb r4, PMCR2_SHIFT(r6) /* Initialize EUMBBAR early since 8245 has internal UART in EUMB */ @@ -471,21 +471,21 @@ X4_KAHLUA_START: L1not8245: - /* Toggle the DLL reset bit in AMBOR */ + /* Toggle the DLL reset bit in AMBOR */ LOADPTR (r3, AMBOR) stwbrx r3,0,r5 lbz r4, 0(r6) - andi. r4, r4, 0xdf + andi. r4, r4, 0xdf stb r4, 0(r6) /* Clear DLL_RESET */ - sync + sync - ori r4, r4, 0x20 /* Set DLL_RESET */ + ori r4, r4, 0x20 /* Set DLL_RESET */ stb r4, 0(r6) - sync + sync - andi. r4, r4, 0xdf + andi. r4, r4, 0xdf stb r4, 0(r6) /* Clear DLL_RESET */ @@ -533,10 +533,10 @@ L1not8245: MC1_MEMGO << 19 | MC1_SREN << 18 | \ MC1_RAM_TYPE << 17 | MC1_PCKEN << 16 ) li r3, MC1_BANKBITS - cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ - bne BankBitsAdd - cmpli 0, 0, r3, 0x5555 - beq K2BankBitsHack /* On 8245, 5555 ==> 0 */ + cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ + bne BankBitsAdd + cmpli 0, 0, r3, 0x5555 + beq K2BankBitsHack /* On 8245, 5555 ==> 0 */ BankBitsAdd: ori r4, r3, 0 K2BankBitsHack: @@ -569,9 +569,9 @@ K2BankBitsHack: MC2_INLRD_PARECC_CHK_EN << 18 | \ MC2_ECC_EN << 17 | MC2_EDO << 16 | \ MC2_REFINT << 2 | MC2_RSV_PG << 1 | MC2_RMW_PAR) - cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ - bne notK2 - /* clear Kahlua2 reserved bits */ + cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ + bne notK2 + /* clear Kahlua2 reserved bits */ LOADPTR (r3, 0xfffcffff) and r4, r4, r3 notK2: @@ -599,9 +599,9 @@ notK2: MC3_RDLAT << 20 | MC3_CPX << 19 | \ MC3_RAS6P << 15 | MC3_CAS5 << 12 | MC3_CP4 << 9 | \ MC3_CAS3 << 6 | MC3_RCD2 << 3 | MC3_RP1) - cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ - bne notK2b - /* clear Kahlua2 reserved bits */ + cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ + bne notK2b + /* clear Kahlua2 reserved bits */ LOADPTR (r3, 0xff000000) and r4, r4, r3 notK2b: @@ -633,9 +633,9 @@ notK2b: MC4_REGDIMM << 15 | MC4_SDMODE_CAS << 12 | \ MC4_SDMODE_WRAP << 11 | MC4_SDMODE_BURST << 8 | \ MC4_ACTORW << 4 | MC4_BSTOPRE_L) - cmpl 0, 0, r7, r9 /* Check for Kahlua 2 */ - bne notK2c - /* Turn on Kahlua2 extended ROM space */ + cmpl 0, 0, r7, r9 /* Check for Kahlua 2 */ + bne notK2c + /* Turn on Kahlua2 extended ROM space */ LOADPTR (r3, 0x00200000) or r4, r4, r3 notK2c: @@ -745,13 +745,12 @@ KahluaX4wait8ref: sync eieio - mtlr r11 + mtlr r11 blr #else /* USE_V2_INIT */ - /* U-Boot works, but memory will not run reliably for all address ranges. * Early U-Boot Working init, but 2.4.19 kernel will crash since memory is not * initialized correctly. Could work if debugged. @@ -898,106 +897,106 @@ write_32_ne: .globl early_init_f early_init_f: - mflr r11 - lis r10, 0x8000 + mflr r11 + lis r10, 0x8000 - /* PCI Latency Timer */ - li r4, 0x0d - ori r3, r10, PLTR@l - bl __pci_config_write_8 + /* PCI Latency Timer */ + li r4, 0x0d + ori r3, r10, PLTR@l + bl __pci_config_write_8 - /* Cache Line Size */ - li r4, 0x08 - ori r3, r10, PCLSR@l - bl __pci_config_write_8 + /* Cache Line Size */ + li r4, 0x08 + ori r3, r10, PCLSR@l + bl __pci_config_write_8 - /* PCI Cmd */ - li r4, 6 - ori r3, r10, PCICR@l - bl __pci_config_write_16 + /* PCI Cmd */ + li r4, 6 + ori r3, r10, PCICR@l + bl __pci_config_write_16 #if 1 - /* PCI Stat */ - ori r3, r10, PCISR@l - bl __pci_config_read_16 - ori r4, r4, 0xffff - ori r3, r10, PCISR@l - bl __pci_config_write_16 + /* PCI Stat */ + ori r3, r10, PCISR@l + bl __pci_config_read_16 + ori r4, r4, 0xffff + ori r3, r10, PCISR@l + bl __pci_config_write_16 #endif - /* PICR1 */ - lis r4, 0xff14 - ori r4, r4, 0x1b98 - ori r3, r10, PICR1@l - bl __pci_config_write_32 + /* PICR1 */ + lis r4, 0xff14 + ori r4, r4, 0x1b98 + ori r3, r10, PICR1@l + bl __pci_config_write_32 - /* PICR2 */ - lis r4, 0x0404 - ori r4, r4, 0x0004 - ori r3, r10, PICR2@l - bl __pci_config_write_32 + /* PICR2 */ + lis r4, 0x0404 + ori r4, r4, 0x0004 + ori r3, r10, PICR2@l + bl __pci_config_write_32 /* MIOCR1 */ - li r4, 0x04 - ori r3, r10, MIOCR1@l - bl __pci_config_write_8 + li r4, 0x04 + ori r3, r10, MIOCR1@l + bl __pci_config_write_8 /* For the MPC8245, set register 77 to %00100000 (see Errata #15) */ /* SDRAM_CLK_DEL (0x77)*/ - li r4, 0x10 - ori r3, r10, MIOCR2@l - bl __pci_config_write_8 + li r4, 0x10 + ori r3, r10, MIOCR2@l + bl __pci_config_write_8 - /* EUMBBAR */ - lis r4, 0xfc00 - ori r3, r10, EUMBBAR@l - bl __pci_config_write_32 + /* EUMBBAR */ + lis r4, 0xfc00 + ori r3, r10, EUMBBAR@l + bl __pci_config_write_32 /* AMBOR */ /* Even if Address Map B is not being used (though it should), - * the memory DLL needs to be cleared/set/cleared before using memory. + * the memory DLL needs to be cleared/set/cleared before using memory. */ - ori r3, r10, AMBOR@l - bl __pci_config_read_8 /* get Current bits */ + ori r3, r10, AMBOR@l + bl __pci_config_read_8 /* get Current bits */ - andi. r4, r4, 0xffdf - ori r3, r10, AMBOR@l - bl __pci_config_write_16 /* Clear DLL_RESET */ + andi. r4, r4, 0xffdf + ori r3, r10, AMBOR@l + bl __pci_config_write_16 /* Clear DLL_RESET */ - ori r4, r4, 0x0020 - ori r3, r10, AMBOR@l - bl __pci_config_write_16 /* Set DLL_RESET */ + ori r4, r4, 0x0020 + ori r3, r10, AMBOR@l + bl __pci_config_write_16 /* Set DLL_RESET */ - andi. r4, r4, 0xffdf - ori r3, r10, AMBOR@l - bl __pci_config_write_16 /* Clear DLL_RESET */ + andi. r4, r4, 0xffdf + ori r3, r10, AMBOR@l + bl __pci_config_write_16 /* Clear DLL_RESET */ - /* ERCR1 */ - lis r4, 0x8040 /* Enable RCS2, use supplied timings */ - ori r4, r4, 0x8000 - ori r3, r10, ERCR1@l - bl __pci_config_write_32 + /* ERCR1 */ + lis r4, 0x8040 /* Enable RCS2, use supplied timings */ + ori r4, r4, 0x8000 + ori r3, r10, ERCR1@l + bl __pci_config_write_32 - /* ERCR2 */ - lis r4, 0x0000 /* Disable RCS3 parms */ - ori r4, r4, 0x0000 - ori r3, r10, ERCR2@l - bl __pci_config_write_32 + /* ERCR2 */ + lis r4, 0x0000 /* Disable RCS3 parms */ + ori r4, r4, 0x0000 + ori r3, r10, ERCR2@l + bl __pci_config_write_32 - /* ERCR3 */ - lis r4, 0x0000 /* RCS3 at 0x70000000, 64K bytes */ - ori r4, r4, 0x0004 - ori r3, r10, ERCR2@l - bl __pci_config_write_32 + /* ERCR3 */ + lis r4, 0x0000 /* RCS3 at 0x70000000, 64K bytes */ + ori r4, r4, 0x0004 + ori r3, r10, ERCR2@l + bl __pci_config_write_32 /* Preserve memgo bit */ - /* MCCR1 */ + /* MCCR1 */ /* lis r4, 0x75a8 / Safe Local ROM = 11+3 clocks */ - lis r4, 0x75a0 /* Safe Local ROM = 11+3 clocks */ + lis r4, 0x75a0 /* Safe Local ROM = 11+3 clocks */ /* lis r4, 0x73a0 / Fast Local ROM = 7+3 clocks */ /* oris r4, r4, 0x0010 / Burst ROM/Flash enable */ /* oris r4, r4, 0x0004 / Self-refresh enable */ @@ -1005,17 +1004,17 @@ early_init_f: /* ori r4,r4,0xFFFF / 16Mbit 2bank SDRAM */ /* ori r4,r4,0xAAAA / 256Mbit 4bank SDRAM (8245 only) */ /* ori r4,r4,0x5555 / 64Mbit 2bank SDRAM */ - ori r4,r4,0x0000 /* 64Mbit 4bank SDRAM */ + ori r4,r4,0x0000 /* 64Mbit 4bank SDRAM */ - ori r3, r10, MCCR1@l - bl __pci_config_write_32 + ori r3, r10, MCCR1@l + bl __pci_config_write_32 - /* MCCR2 */ + /* MCCR2 */ - lis r4,0x0000 + lis r4,0x0000 /* oris r4,r4,0x4000 / TS_WAIT_TIMER = 3 clocks */ - oris r4,r4,0x1000 /* ASRISE = 8 clocks */ - oris r4,r4,0x0080 /* ASFALL = 8 clocks */ + oris r4,r4,0x1000 /* ASRISE = 8 clocks */ + oris r4,r4,0x0080 /* ASFALL = 8 clocks */ /* oris r4,r4,0x0010 / SDRAM Parity (else ECC) */ /* oris r4,r4,0x0008 / Write parity check */ /* oris r4,r4,0x0004 / SDRAM inline reads */ @@ -1030,143 +1029,142 @@ early_init_f: /* ori r4,r4,0x150c / 100 MHz mem bus = 1347 */ /* ori r4,r4,0x10fc / 83 MHz mem bus = 1087 */ /* ori r4,r4,0x0cc4 / 66 MHz mem bus = 817 */ - ori r4,r4,0x04cc /* 33 MHz mem bus (SAFE) = 307 */ + ori r4,r4,0x04cc /* 33 MHz mem bus (SAFE) = 307 */ /* ori r4,r4,0x0002 / Reserve a page */ /* ori r4,r4,0x0001 / RWM parity */ - ori r3, r10, MCCR2@l - bl __pci_config_write_32 + ori r3, r10, MCCR2@l + bl __pci_config_write_32 - /* MCCR3 */ - lis r4,0x0000 /* BSTOPRE_M = 7 (see A/N) */ - oris r4,r4,0x0500 /* REFREC = 8 clocks */ - ori r3, r10, MCCR3@l - bl __pci_config_write_32 + /* MCCR3 */ + lis r4,0x0000 /* BSTOPRE_M = 7 (see A/N) */ + oris r4,r4,0x0500 /* REFREC = 8 clocks */ + ori r3, r10, MCCR3@l + bl __pci_config_write_32 - /* MCCR4 */ /* Turn on registered buffer mode */ - lis r4, 0x2000 /* PRETOACT = 3 clocks */ - oris r4,r4,0x0400 /* ACTOPRE = 5 clocks */ + /* MCCR4 */ /* Turn on registered buffer mode */ + lis r4, 0x2000 /* PRETOACT = 3 clocks */ + oris r4,r4,0x0400 /* ACTOPRE = 5 clocks */ /* oris r4,r4,0x0080 / Enable 8-beat burst (32-bit bus) */ /* oris r4,r4,0x0040 / Enable Inline ECC/Parity */ - oris r4,r4,0x0020 /* EXTROM enabled */ - oris r4,r4,0x0010 /* Registered buffers */ + oris r4,r4,0x0020 /* EXTROM enabled */ + oris r4,r4,0x0010 /* Registered buffers */ /* oris r4,r4,0x0000 / BSTOPRE_U = 0 (see A/N) */ - oris r4,r4,0x0002 /* DBUS_SIZ[2] (8 bit on RCS1) */ + oris r4,r4,0x0002 /* DBUS_SIZ[2] (8 bit on RCS1) */ /* ori r4,r4,0x8000 / Registered DIMMs */ - ori r4,r4,0x2000 /*CAS Latency (CL=3) (see RDLAT) */ + ori r4,r4,0x2000 /*CAS Latency (CL=3) (see RDLAT) */ /* ori r4,r4,0x2000 / CAS Latency (CL=2) (see RDLAT) */ /* ori r4,r4,0x0300 / Sequential wrap/8-beat burst */ - ori r4,r4,0x0200 /* Sequential wrap/4-beat burst */ - ori r4,r4,0x0030 /* ACTORW = 3 clocks */ - ori r4,r4,0x0009 /* BSTOPRE_L = 9 (see A/N) */ + ori r4,r4,0x0200 /* Sequential wrap/4-beat burst */ + ori r4,r4,0x0030 /* ACTORW = 3 clocks */ + ori r4,r4,0x0009 /* BSTOPRE_L = 9 (see A/N) */ - ori r3, r10, MCCR4@l - bl __pci_config_write_32 + ori r3, r10, MCCR4@l + bl __pci_config_write_32 /* MSAR1 */ - lis r4, 0xc0804000@h - ori r4, r4, 0xc0804000@l - ori r3, r10, MSAR1@l - bl __pci_config_write_32 + lis r4, 0xc0804000@h + ori r4, r4, 0xc0804000@l + ori r3, r10, MSAR1@l + bl __pci_config_write_32 /* MSAR2 */ - lis r4, 0xc0804000@h - ori r4, r4, 0xc0804000@l - ori r3, r10, MSAR2@l - bl __pci_config_write_32 + lis r4, 0xc0804000@h + ori r4, r4, 0xc0804000@l + ori r3, r10, MSAR2@l + bl __pci_config_write_32 /* MESAR1 */ - lis r4, 0x00000000@h - ori r4, r4, 0x00000000@l - ori r3, r10, EMSAR1@l - bl __pci_config_write_32 + lis r4, 0x00000000@h + ori r4, r4, 0x00000000@l + ori r3, r10, EMSAR1@l + bl __pci_config_write_32 /* MESAR2 */ - lis r4, 0x01010101@h - ori r4, r4, 0x01010101@l - ori r3, r10, EMSAR2@l - bl __pci_config_write_32 + lis r4, 0x01010101@h + ori r4, r4, 0x01010101@l + ori r3, r10, EMSAR2@l + bl __pci_config_write_32 /* MEAR1 */ - lis r4, 0xffbf7f3f@h - ori r4, r4, 0xffbf7f3f@l - ori r3, r10, MEAR1@l - bl __pci_config_write_32 + lis r4, 0xffbf7f3f@h + ori r4, r4, 0xffbf7f3f@l + ori r3, r10, MEAR1@l + bl __pci_config_write_32 /* MEAR2 */ - lis r4, 0xffbf7f3f@h - ori r4, r4, 0xffbf7f3f@l - ori r3, r10, MEAR2@l - bl __pci_config_write_32 + lis r4, 0xffbf7f3f@h + ori r4, r4, 0xffbf7f3f@l + ori r3, r10, MEAR2@l + bl __pci_config_write_32 /* MEEAR1 */ - lis r4, 0x00000000@h - ori r4, r4, 0x00000000@l - ori r3, r10, EMEAR1@l - bl __pci_config_write_32 + lis r4, 0x00000000@h + ori r4, r4, 0x00000000@l + ori r3, r10, EMEAR1@l + bl __pci_config_write_32 /* MEEAR2 */ - lis r4, 0x01010101@h - ori r4, r4, 0x01010101@l - ori r3, r10, EMEAR2@l - bl __pci_config_write_32 + lis r4, 0x01010101@h + ori r4, r4, 0x01010101@l + ori r3, r10, EMEAR2@l + bl __pci_config_write_32 /* ODCR */ - li r4, 0x7f - ori r3, r10, ODCR@l - bl __pci_config_write_8 + li r4, 0x7f + ori r3, r10, ODCR@l + bl __pci_config_write_8 /* MBER */ - li r4, 0x01 - ori r3, r10, MBER@l - bl __pci_config_write_8 + li r4, 0x01 + ori r3, r10, MBER@l + bl __pci_config_write_8 - /* Page CTR aka PGMAX */ - li r4, 0x32 - ori r3, r10, 0x70 - bl __pci_config_write_8 + /* Page CTR aka PGMAX */ + li r4, 0x32 + ori r3, r10, 0x70 + bl __pci_config_write_8 #if 0 /* CLK Drive */ - ori r4, r10, 0xfc01 /* Top bit will be ignored */ - ori r3, r10, 0x74 - bl __pci_config_write_16 + ori r4, r10, 0xfc01 /* Top bit will be ignored */ + ori r3, r10, 0x74 + bl __pci_config_write_16 #endif /* delay */ - lis r7, 1 - mtctr r7 + lis r7, 1 + mtctr r7 label1: bdnz label1 - /* Set memgo bit */ - /* MCCR1 */ - ori r3, r10, MCCR1@l - bl __pci_config_read_32 - lis r7, 0x0008 - or r4, r3, r7 - ori r3, r10, MCCR1@l - bl __pci_config_write_32 + /* Set memgo bit */ + /* MCCR1 */ + ori r3, r10, MCCR1@l + bl __pci_config_read_32 + lis r7, 0x0008 + or r4, r3, r7 + ori r3, r10, MCCR1@l + bl __pci_config_write_32 /* delay again */ - lis r7, 1 - mtctr r7 + lis r7, 1 + mtctr r7 label2: bdnz label2 #if 0 /* DEBUG: Infinite loop, write then read */ loop: - lis r7, 0xffff - mtctr r7 - li r3, 0x5004 - lis r4, 0xa0a0 - ori r4, r4, 0x5050 + lis r7, 0xffff + mtctr r7 + li r3, 0x5004 + lis r4, 0xa0a0 + ori r4, r4, 0x5050 bl write_32_ne - li r3, 0x5004 + li r3, 0x5004 bl read_32_ne - bdnz loop + bdnz loop #endif - mtlr r11 - blr + mtlr r11 + blr #endif - diff --git a/board/bmw/flash.c b/board/bmw/flash.c index be622743f09..e04af976f2d 100644 --- a/board/bmw/flash.c +++ b/board/bmw/flash.c @@ -91,7 +91,6 @@ byte_parity_odd(unsigned char x) #endif /* 0 */ - static unsigned long flash_id(unsigned char mfct, unsigned char chip) { @@ -135,7 +134,6 @@ flash_id(unsigned char mfct, unsigned char chip) } - unsigned long flash_init(void) { @@ -181,9 +179,9 @@ flash_init(void) switch(pflinfo->flash_id & FLASH_TYPEMASK) { case FLASH_AM040: - pflinfo->size = 0x00080000; + pflinfo->size = 0x00080000; pflinfo->sector_count = 8; - for(j = 0; j < 8; j++) + for(j = 0; j < 8; j++) { pflinfo->start[j] = base_address + 0x00010000 * j; pflinfo->protect[j] = flash[(j << 16) | 0x2]; @@ -201,16 +199,16 @@ flash_init(void) pflinfo->start[j+3] = base_address + 0x00010000 * j; } #if 0 - /* check for protected sectors */ - for (j = 0; j < pflinfo->sector_count; j++) { - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - /* D0 = 1 if protected */ - addr2 = (volatile FLASH_WORD_SIZE *)(pflinfo->start[j]); - if (pflinfo->flash_id & FLASH_MAN_SST) - pflinfo->protect[j] = 0; - else - pflinfo->protect[j] = addr2[2] & 1; - } + /* check for protected sectors */ + for (j = 0; j < pflinfo->sector_count; j++) { + /* read sector protection at sector address, (A7 .. A0) = 0x02 */ + /* D0 = 1 if protected */ + addr2 = (volatile FLASH_WORD_SIZE *)(pflinfo->start[j]); + if (pflinfo->flash_id & FLASH_MAN_SST) + pflinfo->protect[j] = 0; + else + pflinfo->protect[j] = addr2[2] & 1; + } #endif break; } @@ -245,30 +243,30 @@ flash_get_offsets (ulong base, flash_info_t *info) int i; /* set up sector start address table */ - if (info->flash_id & FLASH_MAN_SST) - { - for (i = 0; i < info->sector_count; i++) - info->start[i] = base + (i * 0x00010000); - } - else + if (info->flash_id & FLASH_MAN_SST) + { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000); + } + else if (info->flash_id & FLASH_BTYPE) { - /* set sector offsets for bottom boot block type */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { - info->start[i] = base + (i * 0x00010000) - 0x00030000; - } + /* set sector offsets for bottom boot block type */ + info->start[0] = base + 0x00000000; + info->start[1] = base + 0x00004000; + info->start[2] = base + 0x00006000; + info->start[3] = base + 0x00008000; + for (i = 4; i < info->sector_count; i++) { + info->start[i] = base + (i * 0x00010000) - 0x00030000; + } } else { - /* set sector offsets for top boot block type */ - i = info->sector_count - 1; - info->start[i--] = base + info->size - 0x00004000; - info->start[i--] = base + info->size - 0x00006000; - info->start[i--] = base + info->size - 0x00008000; - for (; i >= 0; i--) { - info->start[i] = base + i * 0x00010000; - } + /* set sector offsets for top boot block type */ + i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00004000; + info->start[i--] = base + info->size - 0x00006000; + info->start[i--] = base + info->size - 0x00008000; + for (; i >= 0; i--) { + info->start[i] = base + i * 0x00010000; + } } } @@ -367,7 +365,7 @@ flash_get_size (vu_long *addr, flash_info_t *info) short i; FLASH_WORD_SIZE value; ulong base = (ulong)addr; - volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)addr; + volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)addr; printf("flash_get_size: \n"); /* Write auto select command: read Manufacturer ID */ @@ -379,123 +377,123 @@ flash_get_size (vu_long *addr, flash_info_t *info) switch (value) { case (FLASH_WORD_SIZE)AMD_MANUFACT: - info->flash_id = FLASH_MAN_AMD; - break; + info->flash_id = FLASH_MAN_AMD; + break; case (FLASH_WORD_SIZE)FUJ_MANUFACT: - info->flash_id = FLASH_MAN_FUJ; - break; + info->flash_id = FLASH_MAN_FUJ; + break; case (FLASH_WORD_SIZE)SST_MANUFACT: - info->flash_id = FLASH_MAN_SST; - break; + info->flash_id = FLASH_MAN_SST; + break; default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - return (0); /* no or unknown flash */ + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return (0); /* no or unknown flash */ } printf("recognised manufacturer"); value = addr2[ADDR3]; /* device ID */ - debug ("\ndev_code=%x\n", value); + debug ("\ndev_code=%x\n", value); switch (value) { case (FLASH_WORD_SIZE)AMD_ID_LV400T: - info->flash_id += FLASH_AM400T; - info->sector_count = 11; - info->size = 0x00080000; - break; /* => 0.5 MB */ + info->flash_id += FLASH_AM400T; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ case (FLASH_WORD_SIZE)AMD_ID_LV400B: - info->flash_id += FLASH_AM400B; - info->sector_count = 11; - info->size = 0x00080000; - break; /* => 0.5 MB */ + info->flash_id += FLASH_AM400B; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ case (FLASH_WORD_SIZE)AMD_ID_LV800T: - info->flash_id += FLASH_AM800T; - info->sector_count = 19; - info->size = 0x00100000; - break; /* => 1 MB */ + info->flash_id += FLASH_AM800T; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ case (FLASH_WORD_SIZE)AMD_ID_LV800B: - info->flash_id += FLASH_AM800B; - info->sector_count = 19; - info->size = 0x00100000; - break; /* => 1 MB */ + info->flash_id += FLASH_AM800B; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ case (FLASH_WORD_SIZE)AMD_ID_LV160T: - info->flash_id += FLASH_AM160T; - info->sector_count = 35; - info->size = 0x00200000; - break; /* => 2 MB */ + info->flash_id += FLASH_AM160T; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ case (FLASH_WORD_SIZE)AMD_ID_LV160B: - info->flash_id += FLASH_AM160B; - info->sector_count = 35; - info->size = 0x00200000; - break; /* => 2 MB */ + info->flash_id += FLASH_AM160B; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ case (FLASH_WORD_SIZE)SST_ID_xF800A: - info->flash_id += FLASH_SST800A; - info->sector_count = 16; - info->size = 0x00100000; - break; /* => 1 MB */ + info->flash_id += FLASH_SST800A; + info->sector_count = 16; + info->size = 0x00100000; + break; /* => 1 MB */ case (FLASH_WORD_SIZE)SST_ID_xF160A: - info->flash_id += FLASH_SST160A; - info->sector_count = 32; - info->size = 0x00200000; - break; /* => 2 MB */ + info->flash_id += FLASH_SST160A; + info->sector_count = 32; + info->size = 0x00200000; + break; /* => 2 MB */ case (FLASH_WORD_SIZE)AMD_ID_F040B: - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x00080000; - break; /* => 0.5 MB */ + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x00080000; + break; /* => 0.5 MB */ default: - info->flash_id = FLASH_UNKNOWN; - return (0); /* => no or unknown flash */ + info->flash_id = FLASH_UNKNOWN; + return (0); /* => no or unknown flash */ } printf("flash id %lx; sector count %x, size %lx\n", info->flash_id,info->sector_count,info->size); /* set up sector start address table */ - if (info->flash_id & FLASH_MAN_SST) - { - for (i = 0; i < info->sector_count; i++) - info->start[i] = base + (i * 0x00010000); - } - else + if (info->flash_id & FLASH_MAN_SST) + { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000); + } + else if (info->flash_id & FLASH_BTYPE) { - /* set sector offsets for bottom boot block type */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { - info->start[i] = base + (i * 0x00010000) - 0x00030000; - } + /* set sector offsets for bottom boot block type */ + info->start[0] = base + 0x00000000; + info->start[1] = base + 0x00004000; + info->start[2] = base + 0x00006000; + info->start[3] = base + 0x00008000; + for (i = 4; i < info->sector_count; i++) { + info->start[i] = base + (i * 0x00010000) - 0x00030000; + } } else { - /* set sector offsets for top boot block type */ - i = info->sector_count - 1; - info->start[i--] = base + info->size - 0x00004000; - info->start[i--] = base + info->size - 0x00006000; - info->start[i--] = base + info->size - 0x00008000; - for (; i >= 0; i--) { - info->start[i] = base + i * 0x00010000; - } + /* set sector offsets for top boot block type */ + i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00004000; + info->start[i--] = base + info->size - 0x00006000; + info->start[i--] = base + info->size - 0x00008000; + for (; i >= 0; i--) { + info->start[i] = base + i * 0x00010000; + } } /* check for protected sectors */ for (i = 0; i < info->sector_count; i++) { - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - /* D0 = 1 if protected */ - addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]); - if (info->flash_id & FLASH_MAN_SST) - info->protect[i] = 0; - else - info->protect[i] = addr2[2] & 1; + /* read sector protection at sector address, (A7 .. A0) = 0x02 */ + /* D0 = 1 if protected */ + addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]); + if (info->flash_id & FLASH_MAN_SST) + info->protect[i] = 0; + else + info->protect[i] = addr2[2] & 1; } /* @@ -503,7 +501,7 @@ flash_get_size (vu_long *addr, flash_info_t *info) */ if (info->flash_id != FLASH_UNKNOWN) { addr2 = (FLASH_WORD_SIZE *)info->start[0]; - *addr2 = (FLASH_WORD_SIZE)0x00F000F0; /* reset bank */ + *addr2 = (FLASH_WORD_SIZE)0x00F000F0; /* reset bank */ } return (info->size); @@ -521,32 +519,32 @@ flash_erase(flash_info_t *info, int s_first, int s_last) unsigned char sh8b; if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; + if (info->flash_id == FLASH_UNKNOWN) { + printf ("- missing\n"); + } else { + printf ("- no sectors to erase\n"); + } + return 1; } if ((info->flash_id == FLASH_UNKNOWN) || - (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) { - printf ("Can't erase unknown flash type - aborted\n"); - return 1; + (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) { + printf ("Can't erase unknown flash type - aborted\n"); + return 1; } prot = 0; for (sect=s_first; sect<=s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } + if (info->protect[sect]) { + prot++; + } } if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); + printf ("- Warning: %d protected sectors will not be erased!\n", + prot); } else { - printf ("\n"); + printf ("\n"); } l_sect = -1; @@ -568,28 +566,28 @@ flash_erase(flash_info_t *info, int s_first, int s_last) /* Start erase on unprotected sectors */ for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (FLASH_WORD_SIZE *)(info->start[0] + ( + if (info->protect[sect] == 0) { /* not protected */ + addr = (FLASH_WORD_SIZE *)(info->start[0] + ( (info->start[sect] - info->start[0]) << sh8b)); - if (info->flash_id & FLASH_MAN_SST) - { - addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; - addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; - addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00800080; - addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; - addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; - addr[0] = (FLASH_WORD_SIZE)0x00500050; /* block erase */ - udelay(30000); /* wait 30 ms */ - } - else - addr[0] = (FLASH_WORD_SIZE)0x00300030; /* sector erase */ - l_sect = sect; - } + if (info->flash_id & FLASH_MAN_SST) + { + addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; + addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; + addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00800080; + addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; + addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; + addr[0] = (FLASH_WORD_SIZE)0x00500050; /* block erase */ + udelay(30000); /* wait 30 ms */ + } + else + addr[0] = (FLASH_WORD_SIZE)0x00300030; /* sector erase */ + l_sect = sect; + } } /* re-enable interrupts if necessary */ if (flag) - enable_interrupts(); + enable_interrupts(); /* wait at least 80us - let's wait 1 ms */ udelay (1000); @@ -598,22 +596,22 @@ flash_erase(flash_info_t *info, int s_first, int s_last) * We wait for the last triggered sector */ if (l_sect < 0) - goto DONE; + goto DONE; start = get_timer (0); last = start; addr = (FLASH_WORD_SIZE *)(info->start[0] + ( (info->start[l_sect] - info->start[0]) << sh8b)); while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) { - if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return 1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - serial_putc ('.'); - last = now; - } + if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { + printf ("Timeout\n"); + return 1; + } + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + serial_putc ('.'); + last = now; + } } DONE: @@ -643,42 +641,42 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) * handle unaligned start bytes */ if ((l = addr - wp) != 0) { - data = 0; - for (i=0, cp=wp; i<l; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - for (; i<4 && cnt>0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt==0 && i<4; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; + data = 0; + for (i=0, cp=wp; i<l; ++i, ++cp) { + data = (data << 8) | (*(uchar *)cp); + } + for (; i<4 && cnt>0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt==0 && i<4; ++i, ++cp) { + data = (data << 8) | (*(uchar *)cp); + } + + if ((rc = write_word(info, wp, data)) != 0) { + return (rc); + } + wp += 4; } /* * handle word aligned part */ while (cnt >= 4) { - data = 0; - for (i=0; i<4; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; - cnt -= 4; + data = 0; + for (i=0; i<4; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_word(info, wp, data)) != 0) { + return (rc); + } + wp += 4; + cnt -= 4; } if (cnt == 0) { - return (0); + return (0); } /* @@ -686,11 +684,11 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) */ data = 0; for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; + data = (data << 8) | *src++; + --cnt; } for (; i<4; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); + data = (data << 8) | (*(uchar *)cp); } return (write_word(info, wp, data)); @@ -704,12 +702,12 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) */ static int write_word (flash_info_t *info, ulong dest, ulong data) { - volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)info->start[0]; - volatile FLASH_WORD_SIZE *dest2; - volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *)&data; + volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)info->start[0]; + volatile FLASH_WORD_SIZE *dest2; + volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *)&data; ulong start; int flag; - int i; + int i; unsigned char sh8b; /* Check the ROM CS */ @@ -723,32 +721,32 @@ static int write_word (flash_info_t *info, ulong dest, ulong data) /* Check if Flash is (sufficiently) erased */ if ((*dest2 & (FLASH_WORD_SIZE)data) != (FLASH_WORD_SIZE)data) { - return (2); + return (2); } /* Disable interrupts which might cause a timeout here */ flag = disable_interrupts(); - for (i=0; i<4/sizeof(FLASH_WORD_SIZE); i++) - { - addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; - addr2[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; - addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00A000A0; - - dest2[i << sh8b] = data2[i]; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* data polling for D7 */ - start = get_timer (0); - while ((dest2[i << sh8b] & (FLASH_WORD_SIZE)0x00800080) != - (data2[i] & (FLASH_WORD_SIZE)0x00800080)) { - if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { - return (1); - } - } - } + for (i=0; i<4/sizeof(FLASH_WORD_SIZE); i++) + { + addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00AA00AA; + addr2[ADDR1 << sh8b] = (FLASH_WORD_SIZE)0x00550055; + addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE)0x00A000A0; + + dest2[i << sh8b] = data2[i]; + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer (0); + while ((dest2[i << sh8b] & (FLASH_WORD_SIZE)0x00800080) != + (data2[i] & (FLASH_WORD_SIZE)0x00800080)) { + if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { + return (1); + } + } + } return (0); } diff --git a/board/bmw/m48t59y.c b/board/bmw/m48t59y.c index 469f1adaf5e..d72c861a13d 100644 --- a/board/bmw/m48t59y.c +++ b/board/bmw/m48t59y.c @@ -320,4 +320,3 @@ rtc_reset (void) { m48_tod_init(); } - diff --git a/board/bmw/ns16550.c b/board/bmw/ns16550.c index b6b6f4c99a2..b1c28eb264a 100644 --- a/board/bmw/ns16550.c +++ b/board/bmw/ns16550.c @@ -55,6 +55,3 @@ int NS16550_tstc(volatile struct NS16550 *com_port) { return ((com_port->lsr & LSR_DR) != 0); } - - - diff --git a/board/bmw/ns16550.h b/board/bmw/ns16550.h index b80ac02af93..0b7b3896f9c 100644 --- a/board/bmw/ns16550.h +++ b/board/bmw/ns16550.h @@ -78,4 +78,3 @@ void NS16550_putc(volatile struct NS16550 *com_port, unsigned char c); unsigned char NS16550_getc(volatile struct NS16550 *com_port); int NS16550_tstc(volatile struct NS16550 *com_port); void NS16550_reinit(volatile struct NS16550 *com_port, int baud_divisor); - diff --git a/board/bmw/u-boot.lds b/board/bmw/u-boot.lds index 5ba99b1f4d3..98584dcf0a5 100644 --- a/board/bmw/u-boot.lds +++ b/board/bmw/u-boot.lds @@ -103,6 +103,11 @@ SECTIONS _edata = .; PROVIDE (edata = .); + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + __start___ex_table = .; __ex_table : { *(__ex_table) } __stop___ex_table = .; @@ -126,4 +131,3 @@ SECTIONS _end = . ; PROVIDE (end = .); } - |