diff options
Diffstat (limited to 'board/egnite/ethernut5/ethernut5.c')
| -rw-r--r-- | board/egnite/ethernut5/ethernut5.c | 198 |
1 files changed, 0 insertions, 198 deletions
diff --git a/board/egnite/ethernut5/ethernut5.c b/board/egnite/ethernut5/ethernut5.c deleted file mode 100644 index 64e341c3779..00000000000 --- a/board/egnite/ethernut5/ethernut5.c +++ /dev/null @@ -1,198 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2011 - * egnite GmbH <info@egnite.de> - * - * (C) Copyright 2010 - * Ole Reinhardt <ole.reinhardt@thermotemp.de> - */ - -/* - * Ethernut 5 general board support - * - * Ethernut is an open source hardware and software project for - * embedded Ethernet devices. Hardware layouts and CAD files are - * freely available under BSD-like license. - * - * Ethernut 5 is the first member of the Ethernut board family - * with U-Boot and Linux support. This implementation is based - * on the original work done by Ole Reinhardt, but heavily modified - * to support additional features and the latest board revision 5.0F. - * - * Main board components are by default: - * - * Atmel AT91SAM9XE512 CPU with 512 kBytes NOR Flash - * 2 x 64 MBytes Micron MT48LC32M16A2P SDRAM - * 512 MBytes Micron MT29F4G08ABADA NAND Flash - * 4 MBytes Atmel AT45DB321D DataFlash - * SMSC LAN8710 Ethernet PHY - * Atmel ATmega168 MCU used for power management - * Linear Technology LTC4411 PoE controller - * - * U-Boot relevant board interfaces are: - * - * 100 Mbit Ethernet with IEEE 802.3af PoE - * RS-232 serial port - * USB host and device - * MMC/SD-Card slot - * Expansion port with I2C, SPI and more... - * - * Typically the U-Boot image is loaded from serial DataFlash into - * SDRAM by the samboot boot loader, which is located in internal - * NOR Flash and provides all essential initializations like CPU - * and peripheral clocks and, of course, the SDRAM configuration. - * - * For testing purposes it is also possibly to directly transfer - * the image into SDRAM via JTAG. A tested configuration exists - * for the Turtelizer 2 hardware dongle and the OpenOCD software. - * In this case the latter will do the basic hardware configuration - * via its reset-init script. - * - * For additional information visit the project home page at - * http://www.ethernut.de/ - */ - -#include <config.h> -#include <init.h> -#include <net.h> -#include <netdev.h> -#include <miiphy.h> -#include <i2c.h> -#include <mmc.h> -#include <atmel_mci.h> -#include <asm/global_data.h> - -#include <asm/arch/at91sam9260.h> -#include <asm/arch/at91sam9260_matrix.h> -#include <asm/arch/at91sam9_smc.h> -#include <asm/arch/at91_common.h> -#include <asm/arch/clk.h> -#include <asm/arch/gpio.h> -#include <asm/io.h> -#include <asm/gpio.h> - -#include "ethernut5_pwrman.h" - -DECLARE_GLOBAL_DATA_PTR; - -/* - * This is called last during early initialization. Most of the basic - * hardware interfaces are up and running. - * - * The SDRAM hardware has been configured by the first stage boot loader. - * We only need to announce its size, using u-boot's memory check. - */ -int dram_init(void) -{ - gd->ram_size = get_ram_size( - (void *)CFG_SYS_SDRAM_BASE, - CFG_SYS_SDRAM_SIZE); - return 0; -} - -#ifdef CONFIG_CMD_NAND -static void ethernut5_nand_hw_init(void) -{ - struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; - struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; - unsigned long csa; - - /* Assign CS3 to NAND/SmartMedia Interface */ - csa = readl(&matrix->ebicsa); - csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; - writel(csa, &matrix->ebicsa); - - /* Configure SMC CS3 for NAND/SmartMedia */ - writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | - AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), - &smc->cs[3].setup); - writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | - AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), - &smc->cs[3].pulse); - writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), - &smc->cs[3].cycle); - writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | - AT91_SMC_MODE_EXNW_DISABLE | - AT91_SMC_MODE_DBW_8 | - AT91_SMC_MODE_TDF_CYCLE(2), - &smc->cs[3].mode); - -#ifdef CFG_SYS_NAND_READY_PIN - /* Ready pin is optional. */ - at91_set_pio_input(CFG_SYS_NAND_READY_PIN, 1); -#endif - gpio_direction_output(CFG_SYS_NAND_ENABLE_PIN, 1); -} -#endif - -/* - * This is called first during late initialization. - */ -int board_init(void) -{ - at91_periph_clk_enable(ATMEL_ID_PIOA); - at91_periph_clk_enable(ATMEL_ID_PIOB); - at91_periph_clk_enable(ATMEL_ID_PIOC); - - /* Set adress of boot parameters. */ - gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100; - /* Initialize UARTs and power management. */ - ethernut5_power_init(); -#ifdef CONFIG_CMD_NAND - ethernut5_nand_hw_init(); -#endif - return 0; -} - -#ifdef CONFIG_MACB -/* - * This is optionally called last during late initialization. - */ -int board_eth_init(struct bd_info *bis) -{ - const char *devname; - unsigned short mode; - - at91_periph_clk_enable(ATMEL_ID_EMAC0); - - /* Need to reset PHY via power management. */ - ethernut5_phy_reset(); - /* Set peripheral pins. */ - at91_macb_hw_init(); - /* Basic EMAC initialization. */ - if (macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, CFG_PHY_ID)) - return -1; - /* - * Early board revisions have a pull-down at the PHY's MODE0 - * strap pin, which forces the PHY into power down. Here we - * switch to all-capable mode. - */ - devname = miiphy_get_current_dev(); - if (miiphy_read(devname, 0, 18, &mode) == 0) { - /* Set mode[2:0] to 0b111. */ - mode |= 0x00E0; - miiphy_write(devname, 0, 18, mode); - /* Soft reset overrides strap pins. */ - miiphy_write(devname, 0, MII_BMCR, BMCR_RESET); - } - /* Sync environment with network devices, needed for nfsroot. */ - return eth_init(); -} -#endif - -#ifdef CONFIG_GENERIC_ATMEL_MCI -int board_mmc_init(struct bd_info *bd) -{ - at91_periph_clk_enable(ATMEL_ID_MCI); - - /* Initialize MCI hardware. */ - at91_mci_hw_init(); - /* Register the device. */ - return atmel_mci_init((void *)ATMEL_BASE_MCI); -} - -int board_mmc_getcd(struct mmc *mmc) -{ - return !at91_get_pio_value(CFG_SYS_MMC_CD_PIN); -} -#endif |