11 files changed, 0 insertions, 578 deletions
diff --git a/board/freescale/imx8mm_evk/README b/board/freescale/imx8mm_evk/README
deleted file mode 100644
index fa3f079f31c..00000000000
--- a/board/freescale/imx8mm_evk/README
+++ /dev/null
@@ -1,37 +0,0 @@
-U-Boot for the NXP i.MX8MM EVK board
-
-Quick Start
-===========
-- Build the ARM Trusted firmware binary
-- Get ddr firmware
-- Build U-Boot
-- Boot
-
-Get and Build the ARM Trusted firmware
-======================================
-Note: builddir is U-Boot build directory (source directory for in-tree builds)
-Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_4.19.35_1.0.0
-$ make PLAT=imx8mm bl31
-$ cp build/imx8mm/release/bl31.bin $(builddir)
-
-Get the ddr firmware
-=============================
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
-$ chmod +x firmware-imx-8.0.bin
-$ ./firmware-imx-8.0
-$ cp firmware-imx-8.0/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
-
-Build U-Boot
-============
-$ export CROSS_COMPILE=aarch64-poky-linux-
-$ make imx8mm_evk_defconfig
-$ export ATF_LOAD_ADDR=0x920000
-$ make flash.bin
-
-Burn the flash.bin to MicroSD card offset 33KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33
-
-Boot
-====
-Set Boot switch to SD boot
diff --git a/board/freescale/imx8mn_evk/README b/board/freescale/imx8mn_evk/README
deleted file mode 100644
index ff3d15c02b7..00000000000
--- a/board/freescale/imx8mn_evk/README
+++ /dev/null
@@ -1,37 +0,0 @@
-U-Boot for the NXP i.MX8MN EVK board
-
-Quick Start
-===========
-- Build the ARM Trusted firmware binary
-- Get firmware-imx package
-- Build U-Boot
-- Boot
-
-Get and Build the ARM Trusted firmware
-======================================
-Note: srctree is U-Boot source directory
-Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_4.19.35_1.1.0
-$ make PLAT=imx8mn bl31
-$ cp build/imx8mn/release/bl31.bin $(srctree)
-
-Get the ddr firmware
-=============================
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.5.bin
-$ chmod +x firmware-imx-8.5.bin
-$ ./firmware-imx-8.5
-$ cp firmware-imx-8.5/firmware/ddr/synopsys/ddr4*.bin $(srctree)
-
-Build U-Boot
-============
-$ export CROSS_COMPILE=aarch64-poky-linux-
-$ make imx8mn_ddr4_evk_defconfig
-$ export ATF_LOAD_ADDR=0x960000
-$ make flash.bin
-
-Burn the flash.bin to MicroSD card offset 32KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
-
-Boot
-====
-Set Boot switch to SD boot
diff --git a/board/freescale/imx8mp_evk/README b/board/freescale/imx8mp_evk/README
deleted file mode 100644
index 7dd3a9352a5..00000000000
--- a/board/freescale/imx8mp_evk/README
+++ /dev/null
@@ -1,41 +0,0 @@
-U-Boot for the NXP i.MX8MP EVK board
-
-Quick Start
-===========
-- Build the ARM Trusted firmware binary
-- Get the firmware-imx package
-- Build U-Boot
-- Boot
-
-Get and Build the ARM Trusted firmware
-======================================
-Note: $(srctree) is the U-Boot source directory
-Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_5.4.3_2.0.0
-$ make PLAT=imx8mp bl31
-$ sudo cp build/imx8mp/release/bl31.bin $(srctree)
-
-Get the ddr firmware
-====================
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.7.bin
-$ chmod +x firmware-imx-8.7.bin
-$ ./firmware-imx-8.7
-$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_1d_dmem.bin
-$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin $(srctree)/lpddr4_pmu_train_1d_imem.bin
-$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_2d_dmem.bin
-$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
-
-Build U-Boot
-============
-$ export CROSS_COMPILE=aarch64-poky-linux-
-$ make imx8mp_evk_defconfig
-$ export ATF_LOAD_ADDR=0x960000
-$ make flash.bin
-
-Burn the flash.bin to the MicroSD card at offset 32KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32; sync
-
-Boot
-====
-Set Boot switch to SD boot
-Use /dev/ttyUSB2 for U-Boot console
diff --git a/board/freescale/imx8mq_evk/README b/board/freescale/imx8mq_evk/README
deleted file mode 100644
index 859f852255e..00000000000
--- a/board/freescale/imx8mq_evk/README
+++ /dev/null
@@ -1,37 +0,0 @@
-U-Boot for the NXP i.MX8MQ EVK board
-
-Quick Start
-===========
-- Build the ARM Trusted firmware binary
-- Get ddr and hdmi fimware
-- Build U-Boot
-- Boot
-
-Get and Build the ARM Trusted firmware
-======================================
-Note: srctree is U-Boot source directory
-Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_4.19.35_1.0.0
-$ make PLAT=imx8mq bl31
-$ cp build/imx8mq/release/bl31.bin $(builddir)
-
-Get the ddr and hdmi firmware
-=============================
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin
-$ chmod +x firmware-imx-7.9.bin
-$ ./firmware-imx-7.9.bin
-$ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir)
-$ cp firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
-
-Build U-Boot
-============
-$ export CROSS_COMPILE=aarch64-poky-linux-
-$ make imx8mq_evk_defconfig
-$ make flash.bin
-
-Burn the flash.bin to MicroSD card offset 33KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33
-
-Boot
-====
-Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.
diff --git a/board/freescale/imx8qxp_mek/README b/board/freescale/imx8qxp_mek/README
deleted file mode 100644
index 6e4eb5996b0..00000000000
--- a/board/freescale/imx8qxp_mek/README
+++ /dev/null
@@ -1,50 +0,0 @@
-U-Boot for the NXP i.MX8QXP EVK board
-
-Quick Start
-===========
-
-- Build the ARM Trusted firmware binary
-- Get scfw_tcm.bin and ahab-container.img
-- Build U-Boot
-- Flash the binary into the SD card
-- Boot
-
-Get and Build the ARM Trusted firmware
-======================================
-
-$ git clone https://source.codeaurora.org/external/imx/imx-atf
-$ cd imx-atf/
-$ git checkout origin/imx_4.19.35_1.1.0 -b imx_4.19.35_1.1.0
-$ make PLAT=imx8qx bl31
-
-Get scfw_tcm.bin and ahab-container.img
-==============================
-
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.2.7.1.bin
-$ chmod +x imx-sc-firmware-1.2.7.1.bin
-$ ./imx-sc-firmware-1.2.7.1.bin
-$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-seco-2.3.1.bin
-$ chmod +x imx-seco-2.3.1.bin
-$ ./imx-seco-2.3.1.bin
-
-Copy the following binaries to U-Boot folder:
-
-$ cp imx-atf/build/imx8qx/release/bl31.bin .
-$ cp imx-seco-2.3.1/firmware/seco/mx8qx-ahab-container.img ./ahab-container.img
-$ cp imx-sc-firmware-1.2.7.1/mx8qx-mek-scfw-tcm.bin	.
-
-Build U-Boot
-============
-$ make imx8qxp_mek_defconfig
-$ make flash.bin
-
-Flash the binary into the SD card
-=================================
-
-Burn the flash.bin binary to SD card offset 32KB:
-
-$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
-
-Boot
-====
-Set Boot switch SW2: 1100.
diff --git a/board/freescale/imxrt1020-evk/README b/board/freescale/imxrt1020-evk/README
deleted file mode 100644
index abee7ca5f3d..00000000000
--- a/board/freescale/imxrt1020-evk/README
+++ /dev/null
@@ -1,31 +0,0 @@
-How to use U-Boot on NXP i.MXRT1020 EVK
------------------------------------------------
-
-- Build U-Boot for i.MXRT1020 EVK:
-
-$ make mrproper
-$ make imxrt1020-evk_defconfig
-$ make
-
-This will generate the SPL image called SPL and the u-boot.img.
-
-- Flash the SPL image into the micro SD card:
-
-sudo dd if=SPL of=/dev/sdX bs=1k seek=1; sync
-
-- Flash the u-boot.img image into the micro SD card:
-
-sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128; sync
-
-- Jumper settings:
-
-SW8: 0 1 1 0
-
-where 0 means bottom position and 1 means top position (from the
-switch label numbers reference).
-
-- Connect the USB cable between the EVK and the PC for the console.
-(The USB console connector is the one close the ethernet connector)
-
-- Insert the micro SD card in the board, power it up and U-Boot messages should
-come up.
diff --git a/board/freescale/imxrt1050-evk/README b/board/freescale/imxrt1050-evk/README
deleted file mode 100644
index a7e68fa9b32..00000000000
--- a/board/freescale/imxrt1050-evk/README
+++ /dev/null
@@ -1,31 +0,0 @@
-How to use U-Boot on NXP i.MXRT1050 EVK
------------------------------------------------
-
-- Build U-Boot for i.MXRT1050 EVK:
-
-$ make mrproper
-$ make imxrt1050-evk_defconfig
-$ make
-
-This will generate the SPL image called SPL and the u-boot.img.
-
-- Flash the SPL image into the micro SD card:
-
-sudo dd if=SPL of=/dev/sdX bs=1k seek=1; sync
-
-- Flash the u-boot.img image into the micro SD card:
-
-sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128; sync
-
-- Jumper settings:
-
-SW7: 1 0 1 0
-
-where 0 means bottom position and 1 means top position (from the
-switch label numbers reference).
-
-- Connect the USB cable between the EVK and the PC for the console.
-(The USB console connector is the one close the ethernet connector)
-
-- Insert the micro SD card in the board, power it up and U-Boot messages should
-come up.
diff --git a/board/freescale/mx6sabreauto/README b/board/freescale/mx6sabreauto/README
deleted file mode 100644
index 4c0fda1a2de..00000000000
--- a/board/freescale/mx6sabreauto/README
+++ /dev/null
@@ -1,82 +0,0 @@
-How to use and build U-Boot on mx6sabreauto
--------------------------------------------
-
-mx6sabreauto_defconfig target supports mx6q/mx6dl/mx6qp sabreauto variants.
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL and u-boot-dtb.img binaries.
-
-- Flash the SPL binary into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-
-- Flash the u-boot-dtb.img binary into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
-
-Booting via Falcon mode
------------------------
-
-Write in mx6sabreauto_defconfig the following define below:
-
-CONFIG_SPL_OS_BOOT=y
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL image called SPL and the u-boot-dtb.img.
-
-- Flash the SPL image into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 && sync
-
-- Flash the u-boot-dtb.img image into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 && sync
-
-Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
-
-$ sudo cp uImage /media/boot
-
-$ sudo cp imx6dl-sabreauto.dtb /media/boot
-
-Create a partition for root file system and extract it there:
-
-$ sudo tar xvf rootfs.tar.gz -C /media/root
-
-The SD card must have enough space for raw "args" and "kernel".
-To configure Falcon mode for the first time, on U-Boot do the following commands:
-
-- Load dtb file from boot partition:
-
-# load mmc 0:1 ${fdt_addr} imx6dl-sabreauto.dtb
-
-- Load kernel image from boot partition:
-
-# load mmc 0:1 ${loadaddr} uImage
-
-- Write kernel at 2MB offset:
-
-# mmc write ${loadaddr} 0x1000 0x4000
-
-- Setup kernel bootargs:
-
-# setenv bootargs "console=ttymxc3,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait quiet rw"
-
-- Prepare args:
-
-# spl export fdt ${loadaddr} - ${fdt_addr}
-
-- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
-
-# mmc write 18000000 0x800 0x800
-
-- Restart the board and then SPL binary will launch the kernel directly.
diff --git a/board/freescale/mx6sabresd/README b/board/freescale/mx6sabresd/README
deleted file mode 100644
index 4ea4454b9f9..00000000000
--- a/board/freescale/mx6sabresd/README
+++ /dev/null
@@ -1,114 +0,0 @@
-How to use and build U-Boot on mx6sabresd
------------------------------------------
-
-The following methods can be used for booting mx6sabresd boards:
-
-1. Booting from SD card
-
-2. Booting from eMMC
-
-3. Booting via Falcon mode (SPL launches the kernel directly)
-
-
-1. Booting from SD card via SPL
--------------------------------
-
-mx6sabresd_defconfig target supports mx6q/mx6dl/mx6qp sabresd variants.
-
-In order to build it:
-
-$ make mx6sabresd_defconfig
-
-$ make
-
-This will generate the SPL and u-boot-dtb.img binaries.
-
-- Flash the SPL binary into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-
-- Flash the u-boot-dtb.img binary into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
-
-
-2. Booting from eMMC
---------------------
-
-$ make mx6sabresd_defconfig
-
-$ make
-
-This will generate the SPL and u-boot-dtb.img binaries.
-
-- Boot first from SD card as shown in the previous section
-
-In U-boot change the eMMC partition config:
-
-=> mmc partconf 2 1 0 0
-
-Mount the eMMC in the host PC:
-
-=> ums 0 mmc 2
-
-- Flash SPL and u-boot-dtb.img binaries into the eMMC:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
-
-Set SW6 to eMMC 8-bit boot: 11010110
-
-
-3. Booting via Falcon mode
---------------------------
-
-$ make mx6sabresd_defconfig
-$ make
-
-This will generate the SPL image called SPL and the u-boot-dtb.img.
-
-- Flash the SPL image into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
-
-- Flash the u-boot-dtb.img image into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
-
-Create a partition for root file system and extract it there:
-
-$ sudo tar xvf rootfs.tar.gz -C /media/root
-
-The SD card must have enough space for raw "args" and "kernel".
-To configure Falcon mode for the first time, on U-Boot do the following commands:
-
-- Setup the IP server:
-
-# setenv serverip <server_ip_address>
-
-- Download dtb file:
-
-# dhcp ${fdt_addr} imx6q-sabresd.dtb
-
-- Download kernel image:
-
-# dhcp ${loadaddr} uImage
-
-- Write kernel at 2MB offset:
-
-# mmc write ${loadaddr} 0x1000 0x4000
-
-- Setup kernel bootargs:
-
-# setenv bootargs "console=ttymxc0,115200 root=/dev/mmcblk1p1 rootfstype=ext4 rootwait quiet rw"
-
-- Prepare args:
-
-# spl export fdt ${loadaddr} - ${fdt_addr}
-
-- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
-
-# mmc write 18000000 0x800 0x800
-
-- Press KEY_VOL_UP key, power up the board and then SPL binary will
-launch the kernel directly.
diff --git a/board/freescale/mx6ul_14x14_evk/README b/board/freescale/mx6ul_14x14_evk/README
deleted file mode 100644
index e101abe48c7..00000000000
--- a/board/freescale/mx6ul_14x14_evk/README
+++ /dev/null
@@ -1,82 +0,0 @@
-How to use U-Boot on Freescale MX6UL 14x14 EVK
------------------------------------------------
-
-- Build U-Boot for MX6UL 14x14 EVK:
-
-$ make mrproper
-$ make mx6ul_14x14_evk_defconfig
-$ make
-
-This will generate the SPL image called SPL and the u-boot.img.
-
-1. Booting via SDCard
----------------------
-
-- Flash the SPL image into the micro SD card:
-
-sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
-
-- Flash the u-boot.img image into the micro SD card:
-
-sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
-
-- Jumper settings:
-
-SW601: 0 0 1 0
-Sw602: 1 0
-
-where 0 means bottom position and 1 means top position (from the
-switch label numbers reference).
-
-- Connect the USB cable between the EVK and the PC for the console.
-(The USB console connector is the one close the push buttons)
-
-- Insert the micro SD card in the board, power it up and U-Boot messages should
-come up.
-
-2. Booting via Serial Download Protocol (SDP)
----------------------------------------------
-
-The mx6ulevk board can boot from USB OTG port using the SDP, target will
-enter in SDP mode in case an SD Card is not connect or boot switches are
-set as below:
-
-Sw602: 0 1
-SW601: x x x x
-
-The following tools can be used to boot via SDP, for both tools you must
-connect an USB cable in USB OTG port.
-
-- Method 1: Universal Update Utility (uuu)
-
-The UUU binary can be downloaded in release tab from link below:
-https://github.com/NXPmicro/mfgtools
-
-The following script should be created to boot SPL + u-boot-dtb.img binaries:
-
-  $ cat uuu_script
-    uuu_version 1.1.4
-
-    SDP: boot -f SPL
-    SDPU: write -f u-boot-dtb.img -addr 0x877fffc0
-    SDPU: jump -addr 0x877fffc0
-    SDPU: done
-
-Please note that the address above is calculated based on SYS_TEXT_BASE address:
-
-0x877fffc0 = 0x87800000 (SYS_TEXT_BASE) - 0x40 (U-Boot proper Header size)
-
-Power on the target and run the following command from U-Boot root directory:
-
-  $ sudo ./uuu uuu_script
-
-- Method 2: imx usb loader tool (imx_usb):
-
-The imx_usb_loader tool can be downloaded in link below:
-https://github.com/boundarydevices/imx_usb_loader
-
-Build the source code and run the following commands from U-Boot root
-directory:
-
-  $ sudo ./imx_usb SPL
-  $ sudo ./imx_usb u-boot-dtb.img
diff --git a/board/freescale/mx6ullevk/README b/board/freescale/mx6ullevk/README
deleted file mode 100644
index d5c87708630..00000000000
--- a/board/freescale/mx6ullevk/README
+++ /dev/null
@@ -1,36 +0,0 @@
-How to use U-Boot on Freescale MX6ULL 14x14 EVK
-----------------------------------------------
-
-- First make sure you have installed the dtc package (device tree compiler):
-
-$ sudo apt-get install device-tree-compiler
-
-- Build U-Boot for MX6ULL 14x14 EVK:
-
-$ make mrproper
-$ make mx6ull_14x14_evk_defconfig
-$ make
-
-This generates the u-boot-dtb.imx image in the current directory.
-
-- Flash the u-boot-dtb.imx image into the micro SD card:
-
-$ sudo dd if=u-boot-dtb.imx of=/dev/sdb bs=1K seek=1 && sync
-
-- Jumper settings:
-
-SW601: 0 0 1 0
-Sw602: 1 0
-
-Where 0 means bottom position and 1 means top position (from the switch label
-numbers reference).
-
-Connect the USB cable between the EVK and the PC for the console.
-(The USB console connector is the one close the push buttons)
-
-Insert the micro SD card in the board, power it up and U-Boot messages should
-come up.
-
-The link for the board: http://www.nxp.com/products/microcontrollers-and- \
-processors/arm-processors/i.mx-applications-processors/i.mx-6-processors/ \
-i.mx6qp/evaluation-kit-for-the-i.mx-6ull-applications-processor:MCIMX6ULL-EVK