diff options
Diffstat (limited to 'board/hisilicon/hikey960/README')
| -rw-r--r-- | board/hisilicon/hikey960/README | 247 |
1 files changed, 0 insertions, 247 deletions
diff --git a/board/hisilicon/hikey960/README b/board/hisilicon/hikey960/README deleted file mode 100644 index 6e01862f8a2..00000000000 --- a/board/hisilicon/hikey960/README +++ /dev/null @@ -1,247 +0,0 @@ -Introduction -============ - -HiKey960 is one of the 96Boards Consumer Edition board from HiSilicon. -The board/SoC has: - -* HiSilicon Kirin960 (HI3660) SoC with 4xCortex-A73 and 4xCortex-A53 -* ARM Mali G71 MP8 GPU -* 3GB LPDDR4 SDRAM -* 32GB UFS Flash Storage -* microSD -* 802.11a/b/g/n WiFi, Bluetooth - -More information about this board can be found in 96Boards website: -https://www.96boards.org/product/hikey960/ - -Currently the u-boot port supports: - -* SD card - -Compile from source -=================== - -First get all the sources - - > mkdir -p ~/hikey960/src ~/hikey960/bin - > cd ~/hikey960/src - > git clone https://github.com/ARM-software/arm-trusted-firmware - > git clone https://github.com/96boards-hikey/OpenPlatformPkg -b testing/hikey960_v1.3.4 - > git clone https://github.com/96boards-hikey/l-loader -b testing/hikey960_v1.2 - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/config - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/hisi-sec_usb_xloader.img - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/hisi-sec_uce_boot.img - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/hisi-sec_xloader.img - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/recovery.bin - > wget http://snapshots.linaro.org/reference-platform/components/uefi-staging/123/hikey960/release/hikey_idt - -Get the SCP_BL2 lpm3.img binary. It is shipped as part of the UEFI source. -The latest version can be obtained from the OpenPlatformPkg repo. - - > cp OpenPlatformPkg/Platforms/Hisilicon/HiKey960/Binary/lpm3.img ~/hikey960/bin/ - -Compile U-Boot -============== - - > cd ~/hikey960/src/u-boot - > make CROSS_COMPILE=aarch64-linux-gnu- hikey960_defconfig - > make CROSS_COMPILE=aarch64-linux-gnu- - > cp u-boot.bin ~/hikey960/bin/ - -Compile ARM Trusted Firmware (ATF) -================================== - - > cd ~/hikey960/src/arm-trusted-firmware - > make CROSS_COMPILE=aarch64-linux-gnu- all fip \ - SCP_BL2=~/hikey960/bin/lpm3.img \ - BL33=~/hikey960/bin/u-boot.bin DEBUG=1 PLAT=hikey960 - -Copy the resulting FIP binary - > cp build/hikey960/debug/fip.bin ~/hikey960/bin - -Compile l-loader -================ - > cd ~/hikey960/src/l-loader - > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/bl1.bin - > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/bl2.bin - > ln -sf ~/hikey960/src/arm-trusted-firmware/build/hikey960/debug/fip.bin - > ln -sf ~/hikey960/bin/u-boot.bin - > make hikey960 PTABLE_LST=linux-32g NS_BL1U=u-boot.bin - -Copy the resulting binaries - > cp *.img ~/hikey960/bin - > cp l-loader.bin ~/hikey960/bin - -These instructions are adapted from -https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/hikey960.rst - -Setup Console -============= - -Install ser2net. Use telnet as the console since UEFI in recovery mode -output window fails to display in minicom. - - > sudo apt-get install ser2net - -Configure ser2net - - > sudo vi /etc/ser2net.conf - -Append one line for serial-over-USB in #ser2net.conf - - > 2004:telnet:0:/dev/ttyUSB0:115200 8DATABITS NONE 1STOPBIT banner - -Start ser2net - - > sudo killall ser2net - > sudo ser2net -u - -Open the console. - - > telnet localhost 2004 - -And you could open the console remotely, too. - -Flashing -======== - -1. Boot Hikey960 into recovery mode as per the below document: -https://github.com/96boards/documentation/blob/master/consumer/hikey/hikey960/installation/board-recovery.md - -Once Hikey960 is in recovery mode, flash the recovery binary: - - > cd ~/hikey960/src - > chmod +x ./hikey_idt - > sudo ./hikey_idt -c config -p /dev/ttyUSB1 - -Now move to the Hikey960 console and press `f` during UEFI boot. This -will allow the board to boot into fastboot mode. Once the board is in -fastboot mode, you should see the ID of the HiKey960 board using the -following command - - > sudo fastboot devices - -1ED3822A018E3372 fastboot - -3. Flash the images - -Now, the images can be flashed using fastboot: - - > sudo fastboot flash ptable ~/hikey960/bin/prm_ptable.img - > sudo fastboot flash xloader ~/hikey960/bin/hisi-sec_xloader.img - > sudo fastboot flash fastboot ~/hikey960/bin/l-loader.bin - > sudo fastboot flash fip ~/hikey960/bin/fip.bin - -4. Set the "Boot Mode" switch to OFF position for normal boot mode. -Then power on HiKey960 - -Observe the console traces using UART6 on the Low Speed Expansion header: - -NOTICE: BL2: v2.1(debug):v2.1-531-g3ee48f40 -NOTICE: BL2: Built : 18:15:58, Aug 2 2019 -INFO: BL2: Doing platform setup -INFO: UFS LUN0 contains 1024 blocks with 4096-byte size -INFO: UFS LUN1 contains 1024 blocks with 4096-byte size -INFO: UFS LUN2 contains 2048 blocks with 4096-byte size -INFO: UFS LUN3 contains 7805952 blocks with 4096-byte size -INFO: ufs: change power mode success -INFO: BL2: Loading image id 2 -INFO: Loading image id=2 at address 0x89c80000 -INFO: Image id=2 loaded: 0x89c80000 - 0x89cb5088 -INFO: BL2: Initiating SCP_BL2 transfer to SCP -INFO: BL2: SCP_BL2: 0x89c80000@0x35088 -INFO: BL2: SCP_BL2 HEAD: -INFO: BL2: SCP_BL2 0x7000 0x179 0x159 0x149 -INFO: BL2: SCP_BL2 0x189 0x18b 0x18d 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x18f -INFO: BL2: SCP_BL2 0x191 0x0 0x193 0x195 -INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd -INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd -INFO: BL2: SCP_BL2 0x18fd 0x18fd 0x18fd 0x18fd -INFO: BL2: SCP_BL2 0x4d454355 0x43494741 0x424d554e 0x21215245 -INFO: BL2: SCP_BL2 0x4a054904 0x42912000 0xf841bfbc 0xe7fa0b04 -INFO: BL2: SCP_BL2 0xb88cf000 0x3b18 0x3d1c 0x6809493e -INFO: BL2: SCP_BL2 0x4613680a 0x201f102 0xf0002a04 0x600a804c -INFO: BL2: SCP_BL2 0x204f04f 0xf203fb02 0xf102440a 0x60100204 -INFO: BL2: SCP_BL2 0x160f04f 0xf103fb01 0x68004834 0x61044408 -INFO: BL2: SCP_BL2 0x61866145 0xf8c061c7 0xf8c08020 0xf8c09024 -INFO: BL2: SCP_BL2 0xf8c0a028 0xf3efb02c 0xf3ef8208 0x68118309 -INFO: BL2: SCP_BL2 0xf1026401 0xf0110204 0xbf070f04 0x46113220 -INFO: BL2: SCP_BL2 TAIL: -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x19cad151 0x19b80040 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 0x0 0x0 0x0 0x0 -INFO: BL2: SCP_BL2 transferred to SCP -INFO: start fw loading -INFO: fw load success -WARNING: BL2: Platform setup already done!! -INFO: BL2: Loading image id 3 -INFO: Loading image id=3 at address 0x1ac58000 -INFO: Image id=3 loaded: 0x1ac58000 - 0x1ac63024 -INFO: BL2: Loading image id 5 -INFO: Loading image id=5 at address 0x1ac98000 -INFO: Image id=5 loaded: 0x1ac98000 - 0x1ad0819c -NOTICE: BL2: Booting BL31 -INFO: Entry point address = 0x1ac58000 -INFO: SPSR = 0x3cd -NOTICE: BL31: v2.1(debug):v2.1-531-g3ee48f40 -NOTICE: BL31: Built : 18:16:01, Aug 2 2019 -INFO: ARM GICv2 driver initialized -INFO: BL31: Initializing runtime services -INFO: BL31: cortex_a53: CPU workaround for 855873 was applied -INFO: plat_setup_psci_ops: sec_entrypoint=0x1ac580fc -INFO: BL31: Preparing for EL3 exit to normal world -INFO: Entry point address = 0x1ac98000 -INFO: SPSR = 0x3c9 - - -U-Boot 2019.07-00628-g286f05a6fc-dirty (Aug 02 2019 - 17:14:05 +0530) -Hikey960 - -DRAM: 3 GiB -PSCI: v1.1 -MMC: dwmmc1@ff37f000: 0 -Loading Environment from EXT4... ** File not found /uboot.env ** - -** Unable to read "/uboot.env" from mmc0:2 ** -In: serial@fff32000 -Out: serial@fff32000 -Err: serial@fff32000 -Net: Net Initialization Skipped -No ethernet found. -Hit any key to stop autoboot: 0 -switch to partitions #0, OK -mmc0 is current device -Scanning mmc 0:1... -Found /extlinux/extlinux.conf -Retrieving file: /extlinux/extlinux.conf -201 bytes read in 12 ms (15.6 KiB/s) -1: hikey960-kernel -Retrieving file: /Image -24689152 bytes read in 4377 ms (5.4 MiB/s) -append: earlycon=pl011,mmio32,0xfff32000 console=ttyAMA6,115200 rw root=/dev/mmcblk0p2 rot -Retrieving file: /hi3660-hikey960.dtb -35047 bytes read in 14 ms (2.4 MiB/s) -## Flattened Device Tree blob at 10000000 - Booting using the fdt blob at 0x10000000 - Using Device Tree in place at 0000000010000000, end 000000001000b8e6 - -Starting kernel ... - -[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] -[ 0.000000] Linux version 5.2.0-03138-gd75da80dce39 (mani@Mani-XPS-13-9360) (gcc versi9 -[ 0.000000] Machine model: HiKey960 -[ 0.000000] earlycon: pl11 at MMIO32 0x00000000fff32000 (options '') -[ 0.000000] printk: bootconsole [pl11] enabled -[ 0.000000] efi: Getting EFI parameters from FDT: |