summaryrefslogtreecommitdiff
path: root/board/hymod/bsp.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/hymod/bsp.c')
-rw-r--r--board/hymod/bsp.c307
1 files changed, 307 insertions, 0 deletions
diff --git a/board/hymod/bsp.c b/board/hymod/bsp.c
new file mode 100644
index 00000000000..a33c97c6055
--- /dev/null
+++ b/board/hymod/bsp.c
@@ -0,0 +1,307 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * hacked for Hymod FPGA support by Murray.Jensen@cmst.csiro.au, 29-Jan-01
+ */
+
+#include <common.h>
+#include <command.h>
+#include <net.h>
+#include <i2c.h>
+#include <asm/iopin_8260.h>
+#include <cmd_bsp.h>
+
+/*-----------------------------------------------------------------------
+ * Board Special Commands: FPGA load/store, EEPROM erase
+ */
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+
+#define LOAD_SUCCESS 0
+#define LOAD_FAIL_NOCONF 1
+#define LOAD_FAIL_NOINIT 2
+#define LOAD_FAIL_NODONE 3
+
+#define STORE_SUCCESS 0
+
+/*
+ * Programming the Hymod FPGAs
+ *
+ * The 8260 io port config table is set up so that the INIT pin is
+ * held Low (Open Drain output 0) - this will delay the automatic
+ * Power-On config until INIT is released (by making it an input).
+ *
+ * If the FPGA has been programmed before, then the assertion of PROGRAM
+ * will initiate configuration (i.e. it begins clearing the RAM).
+ *
+ * When the FPGA is ready to receive configuration data (either after
+ * releasing INIT after Power-On, or after asserting PROGRAM), it will
+ * pull INIT high.
+ *
+ * Notes from Paul Dunn:
+ *
+ * 1. program pin should be forced low for >= 300ns
+ * (about 20 bus clock cycles minimum).
+ *
+ * 2. then wait for init to go high, which signals
+ * that the FPGA has cleared its internal memory
+ * and is ready to load
+ *
+ * 3. perform load writes of entire config file
+ *
+ * 4. wait for done to go high, which should be
+ * within a few bus clock cycles. If done has not
+ * gone high after reasonable period, then load
+ * has not worked (wait several ms?)
+ */
+
+int fpga_load (int mezz, uchar * addr, ulong size)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ hymod_conf_t *cp = &gd->bd->bi_hymod_conf;
+ xlx_iopins_t *fpgaio;
+ volatile uchar *fpgabase;
+ volatile uint cnt;
+ uchar *eaddr = addr + size;
+ int result;
+
+ if (mezz) {
+ if (!cp->mezz.mmap[0].prog.exists)
+ return (LOAD_FAIL_NOCONF);
+ fpgabase = (uchar *) cp->mezz.mmap[0].prog.base;
+ fpgaio = &cp->mezz.iopins[0];
+ } else {
+ if (!cp->main.mmap[0].prog.exists)
+ return (LOAD_FAIL_NOCONF);
+ fpgabase = (uchar *) cp->main.mmap[0].prog.base;
+ fpgaio = &cp->main.iopins[0];
+ }
+
+ /* set enable HIGH if required */
+ if (fpgaio->enable_pin.flag)
+ iopin_set_high (&fpgaio->enable_pin);
+
+ /* ensure INIT is released (set it to be an input) */
+ iopin_set_in (&fpgaio->init_pin);
+
+ /* toggle PROG Low then High (will already be Low after Power-On) */
+ iopin_set_low (&fpgaio->prog_pin);
+ udelay (1); /* minimum 300ns - 1usec should do it */
+ iopin_set_high (&fpgaio->prog_pin);
+
+ /* wait for INIT High */
+ cnt = 0;
+ while (!iopin_is_high (&fpgaio->init_pin))
+ if (++cnt == 10000000) {
+ result = LOAD_FAIL_NOINIT;
+ goto done;
+ }
+
+ /* write configuration data */
+ while (addr < eaddr)
+ *fpgabase = *addr++;
+
+ /* wait for DONE High */
+ cnt = 0;
+ while (!iopin_is_high (&fpgaio->done_pin))
+ if (++cnt == 100000000) {
+ result = LOAD_FAIL_NODONE;
+ goto done;
+ }
+
+ /* success */
+ result = LOAD_SUCCESS;
+
+ done:
+
+ if (fpgaio->enable_pin.flag)
+ iopin_set_low (&fpgaio->enable_pin);
+
+ return (result);
+}
+
+/* ------------------------------------------------------------------------- */
+int
+do_fpga (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ uchar *addr, *save_addr;
+ ulong size;
+ int mezz, arg, result;
+
+ switch (argc) {
+
+ case 0:
+ case 1:
+ break;
+
+ case 2:
+ if (strcmp (argv[1], "info") == 0) {
+ printf ("\nHymod FPGA Info...\n");
+ printf (" Address Size\n");
+ printf (" Main Configuration: 0x%08x %d\n",
+ FPGA_MAIN_CFG_BASE, FPGA_MAIN_CFG_SIZE);
+ printf (" Main Register: 0x%08x %d\n",
+ FPGA_MAIN_REG_BASE, FPGA_MAIN_REG_SIZE);
+ printf (" Main Port: 0x%08x %d\n",
+ FPGA_MAIN_PORT_BASE, FPGA_MAIN_PORT_SIZE);
+ printf (" Mezz Configuration: 0x%08x %d\n",
+ FPGA_MEZZ_CFG_BASE, FPGA_MEZZ_CFG_SIZE);
+ return 0;
+ }
+ break;
+
+ case 3:
+ if (strcmp (argv[1], "store") == 0) {
+ addr = (uchar *) simple_strtoul (argv[2], NULL, 16);
+
+ save_addr = addr;
+#if 0
+ /* reading config data unimplemented */
+ while VM
+ :more config data * addr++ = *fpga;
+ result = VM:? ? ?
+#else
+ result = 0;
+#endif
+ if (result == STORE_SUCCESS) {
+ printf ("SUCCEEDED (%d bytes)\n", addr - save_addr);
+ return 0;
+ } else
+ printf ("FAILED (%d bytes)\n", addr - save_addr);
+ return 1;
+ }
+ break;
+
+ case 4:
+ if (strcmp (argv[1], "tftp") == 0) {
+ copy_filename (BootFile, argv[2], sizeof (BootFile));
+ load_addr = simple_strtoul (argv[3], NULL, 16);
+
+ if (NetLoop (TFTP) == 0) {
+ printf ("tftp transfer failed - aborting fgpa load\n");
+ return 1;
+ }
+
+ if (NetBootFileXferSize == 0) {
+ printf ("can't determine file size - aborting fpga load\n");
+ return 1;
+ }
+
+ printf ("File transfer succeeded - beginning fpga load...");
+
+ result = fpga_load (0, (uchar *) load_addr,
+ NetBootFileXferSize);
+ if (result == LOAD_SUCCESS) {
+ printf ("SUCCEEDED\n");
+ return 0;
+ } else if (result == LOAD_FAIL_NOINIT)
+ printf ("FAILED (no INIT)\n");
+ else
+ printf ("FAILED (no DONE)\n");
+ return 1;
+
+ }
+ /* fall through ... */
+
+ case 5:
+ if (strcmp (argv[1], "load") == 0) {
+ if (argc == 5) {
+ if (strcmp (argv[2], "main") == 0)
+ mezz = 0;
+ else if (strcmp (argv[2], "mezz") == 0)
+ mezz = 1;
+ else {
+ printf ("FPGA type must be either `main' or `mezz'\n");
+ return 1;
+ }
+ arg = 3;
+ } else {
+ mezz = 0;
+ arg = 2;
+ }
+ addr = (uchar *) simple_strtoul (argv[arg++], NULL, 16);
+ size = (ulong) simple_strtoul (argv[arg], NULL, 16);
+
+ result = fpga_load (mezz, addr, size);
+ if (result == LOAD_SUCCESS) {
+ printf ("SUCCEEDED\n");
+ return 0;
+ } else if (result == LOAD_FAIL_NOINIT)
+ printf ("FAILED (no INIT)\n");
+ else
+ printf ("FAILED (no DONE)\n");
+ return 1;
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+}
+
+/* ------------------------------------------------------------------------- */
+int
+do_eecl (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ uchar data[HYMOD_EEPROM_SIZE];
+ uint offset;
+ int rcode = 0;
+
+ switch (argc) {
+
+ case 1:
+ offset = HYMOD_EEOFF_MAIN;
+ break;
+
+ case 2:
+ if (strcmp (argv[1], "main") == 0) {
+ offset = HYMOD_EEOFF_MAIN;
+ break;
+ }
+ if (strcmp (argv[1], "mezz") == 0) {
+ offset = HYMOD_EEOFF_MEZZ;
+ break;
+ }
+ /* fall through ... */
+
+ default:
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ memset (data, 0, HYMOD_EEPROM_SIZE);
+ if (i2c_write
+ (CFG_I2C_EEPROM_ADDR | offset, 0, CFG_I2C_EEPROM_ADDR_LEN, data,
+ HYMOD_EEPROM_SIZE)) {
+ rcode = 1;
+ }
+
+ return rcode;
+}
+
+#endif /* CFG_CMD_BSP */
+
+/* ------------------------------------------------------------------------- */
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-19 11:25:07 +0000