diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/BuR/tseries/board.c | 2 | ||||
| -rw-r--r-- | board/BuR/tseries/mux.c | 9 | ||||
| -rw-r--r-- | board/compulab/cm_t35/cm_t35.c | 12 | ||||
| -rw-r--r-- | board/samsung/common/board.c | 13 | ||||
| -rw-r--r-- | board/samsung/goni/goni.c | 8 | ||||
| -rw-r--r-- | board/samsung/smdk5250/Makefile | 4 | ||||
| -rw-r--r-- | board/samsung/smdk5250/exynos5-dt.c | 238 | ||||
| -rw-r--r-- | board/samsung/smdk5250/smdk5250.c | 363 | ||||
| -rw-r--r-- | board/samsung/smdk5420/smdk5420.c | 3 | ||||
| -rw-r--r-- | board/ti/am43xx/Makefile | 2 | ||||
| -rw-r--r-- | board/ti/am43xx/board.c | 55 |
11 files changed, 313 insertions, 396 deletions
diff --git a/board/BuR/tseries/board.c b/board/BuR/tseries/board.c index f0510e599e9..c0178e75cfc 100644 --- a/board/BuR/tseries/board.c +++ b/board/BuR/tseries/board.c @@ -117,7 +117,9 @@ void sdram_init(void) int board_init(void) { gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; +#ifdef CONFIG_NAND gpmc_init(); +#endif return 0; } diff --git a/board/BuR/tseries/mux.c b/board/BuR/tseries/mux.c index 3c76e969265..210ac717388 100644 --- a/board/BuR/tseries/mux.c +++ b/board/BuR/tseries/mux.c @@ -27,6 +27,11 @@ static struct module_pin_mux uart0_pin_mux[] = { }; #ifdef CONFIG_MMC static struct module_pin_mux mmc1_pin_mux[] = { + {OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT7 */ + {OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT6 */ + {OFFSET(gpmc_ad5), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT5 */ + {OFFSET(gpmc_ad4), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT4 */ + {OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT3 */ {OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT2 */ {OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT1 */ @@ -125,7 +130,7 @@ static struct module_pin_mux gpIOs[] = { {OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)}, /* TIMER6 (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */ {OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)}, - /* GPIO2_28 (MMC0_DAT1) - MII_nNAND */ + /* GPIO2_27 (MMC0_DAT1) - MII_nNAND */ {OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)}, /* GPIO2_29 (MMC0_DAT0) - NAND_1n0 */ {OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)}, @@ -148,7 +153,7 @@ static struct module_pin_mux gpIOs[] = { * DISPLAY_ONOFF (Backlight Enable at LVDS Versions) */ {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)}, - /* GPIO0_19 (DMA_INTR0) - ISPLAY_MODE (CPLD) */ + /* GPIO0_19 (DMA_INTR0) - DISPLAY_MODE (CPLD) */ {OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, /* GPIO0_20 (DMA_INTR1) - REP-Switch */ {OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)}, diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c index 00bcf41bb3b..0944903ec88 100644 --- a/board/compulab/cm_t35/cm_t35.c +++ b/board/compulab/cm_t35/cm_t35.c @@ -54,12 +54,12 @@ static u32 gpmc_net_config[GPMC_MAX_REG] = { }; static u32 gpmc_nand_config[GPMC_MAX_REG] = { - SMNAND_GPMC_CONFIG1, - SMNAND_GPMC_CONFIG2, - SMNAND_GPMC_CONFIG3, - SMNAND_GPMC_CONFIG4, - SMNAND_GPMC_CONFIG5, - SMNAND_GPMC_CONFIG6, + M_NAND_GPMC_CONFIG1, + M_NAND_GPMC_CONFIG2, + M_NAND_GPMC_CONFIG3, + M_NAND_GPMC_CONFIG4, + M_NAND_GPMC_CONFIG5, + M_NAND_GPMC_CONFIG6, 0, }; diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index de154e0f648..9dc7c832e6e 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -243,13 +243,6 @@ int board_eth_init(bd_t *bis) int board_mmc_init(bd_t *bis) { int ret; - -#ifdef CONFIG_SDHCI - /* mmc initializattion for available channels */ - ret = exynos_mmc_init(gd->fdt_blob); - if (ret) - debug("mmc init failed\n"); -#endif #ifdef CONFIG_DWMMC /* dwmmc initializattion for available channels */ ret = exynos_dwmmc_init(gd->fdt_blob); @@ -257,6 +250,12 @@ int board_mmc_init(bd_t *bis) debug("dwmmc init failed\n"); #endif +#ifdef CONFIG_SDHCI + /* mmc initializattion for available channels */ + ret = exynos_mmc_init(gd->fdt_blob); + if (ret) + debug("mmc init failed\n"); +#endif return ret; } #endif diff --git a/board/samsung/goni/goni.c b/board/samsung/goni/goni.c index 4cea63b813e..eb0f9bffae0 100644 --- a/board/samsung/goni/goni.c +++ b/board/samsung/goni/goni.c @@ -14,6 +14,8 @@ #include <asm/arch/cpu.h> #include <power/max8998_pmic.h> #include <samsung/misc.h> +#include <usb.h> +#include <usb_mass_storage.h> DECLARE_GLOBAL_DATA_PTR; @@ -175,6 +177,12 @@ struct s3c_plat_otg_data s5pc110_otg_data = { .regs_otg = S5PC110_OTG_BASE, .usb_phy_ctrl = S5PC110_USB_PHY_CONTROL, }; + +int board_usb_init(int index, enum usb_init_type init) +{ + debug("USB_udc_probe\n"); + return s3c_udc_probe(&s5pc110_otg_data); +} #endif #ifdef CONFIG_MISC_INIT_R diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile index 6a586553e1f..3d96b077b4c 100644 --- a/board/samsung/smdk5250/Makefile +++ b/board/samsung/smdk5250/Makefile @@ -7,9 +7,5 @@ obj-y += smdk5250_spl.o ifndef CONFIG_SPL_BUILD -ifdef CONFIG_OF_CONTROL obj-y += exynos5-dt.o -else -obj-y += smdk5250.o -endif endif diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c index 58821c41a41..d6ce1337b94 100644 --- a/board/samsung/smdk5250/exynos5-dt.c +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -11,15 +11,16 @@ #include <i2c.h> #include <netdev.h> #include <spi.h> +#include <asm/gpio.h> #include <asm/arch/cpu.h> #include <asm/arch/dwmmc.h> -#include <asm/arch/gpio.h> #include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> #include <asm/arch/power.h> #include <asm/arch/sromc.h> #include <power/pmic.h> #include <power/max77686_pmic.h> +#include <power/tps65090_pmic.h> #include <tmu.h> DECLARE_GLOBAL_DATA_PTR; @@ -41,7 +42,197 @@ int exynos_init(void) return 0; } +#if defined(CONFIG_POWER) +#ifdef CONFIG_POWER_MAX77686 +static int pmic_reg_update(struct pmic *p, int reg, uint regval) +{ + u32 val; + int ret = 0; + + ret = pmic_reg_read(p, reg, &val); + if (ret) { + debug("%s: PMIC %d register read failed\n", __func__, reg); + return -1; + } + val |= regval; + ret = pmic_reg_write(p, reg, val); + if (ret) { + debug("%s: PMIC %d register write failed\n", __func__, reg); + return -1; + } + return 0; +} + +static int max77686_init(void) +{ + struct pmic *p; + + if (pmic_init(I2C_PMIC)) + return -1; + + p = pmic_get("MAX77686_PMIC"); + if (!p) + return -ENODEV; + + if (pmic_probe(p)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT, + MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V)) + return -1; + + /* VDD_MIF */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT, + MAX77686_BUCK1OUT_1V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK1OUT); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL, + MAX77686_BUCK1CTRL_EN)) + return -1; + + /* VDD_ARM */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1, + MAX77686_BUCK2DVS1_1_3V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK2DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1, + MAX77686_BUCK2CTRL_ON)) + return -1; + + /* VDD_INT */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1, + MAX77686_BUCK3DVS1_1_0125V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK3DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_G3D */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1, + MAX77686_BUCK4DVS1_1_2V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK4DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_LDO2 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1, + MAX77686_LD02CTRL1_1_5V | EN_LDO)) + return -1; + + /* VDD_LDO3 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1, + MAX77686_LD03CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO5 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1, + MAX77686_LD05CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO10 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1, + MAX77686_LD10CTRL1_1_8V | EN_LDO)) + return -1; + + return 0; +} +#endif /* CONFIG_POWER_MAX77686 */ + +int exynos_power_init(void) +{ + int ret = 0; + +#ifdef CONFIG_POWER_MAX77686 + ret = max77686_init(); + if (ret) + return ret; +#endif +#ifdef CONFIG_POWER_TPS65090 + /* + * The TPS65090 may not be in the device tree. If so, it is not + * an error. + */ + ret = tps65090_init(); + if (ret == 0 || ret == -ENODEV) + return 0; +#endif + + return ret; +} +#endif /* CONFIG_POWER */ + #ifdef CONFIG_LCD +static int board_dp_bridge_setup(void) +{ + const int max_tries = 10; + int num_tries, node; + + /* + * TODO(sjg): Use device tree for GPIOs when exynos GPIO + * numbering patch is in mainline. + */ + debug("%s\n", __func__); + node = fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_NXP_PTN3460); + if (node < 0) { + debug("%s: No node for DP bridge in device tree\n", __func__); + return -ENODEV; + } + + /* Setup the GPIOs */ + + /* PD is ACTIVE_LOW, and initially de-asserted */ + gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_Y25, 1); + + /* Reset is ACTIVE_LOW */ + gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE); + gpio_direction_output(EXYNOS5_GPIO_X15, 0); + + udelay(10); + gpio_set_value(EXYNOS5_GPIO_X15, 1); + + gpio_direction_input(EXYNOS5_GPIO_X07); + + /* + * We need to wait for 90ms after bringing up the bridge since there + * is a phantom "high" on the HPD chip during its bootup. The phantom + * high comes within 7ms of de-asserting PD and persists for at least + * 15ms. The real high comes roughly 50ms after PD is de-asserted. The + * phantom high makes it hard for us to know when the NXP chip is up. + */ + mdelay(90); + + for (num_tries = 0; num_tries < max_tries; num_tries++) { + /* Check HPD. If it's high, we're all good. */ + if (gpio_get_value(EXYNOS5_GPIO_X07)) + return 0; + + debug("%s: eDP bridge failed to come up; try %d of %d\n", + __func__, num_tries, max_tries); + } + + /* Immediately go into bridge reset if the hp line is not high */ + return -ENODEV; +} + void exynos_cfg_lcd_gpio(void) { /* For Backlight */ @@ -60,4 +251,49 @@ void exynos_set_dp_phy(unsigned int onoff) { set_dp_phy_ctrl(onoff); } + +void exynos_backlight_on(unsigned int on) +{ + debug("%s(%u)\n", __func__, on); + + if (!on) + return; + +#ifdef CONFIG_POWER_TPS65090 + int ret; + + ret = tps65090_fet_enable(1); /* Enable FET1, backlight */ + if (ret) + return; + + /* T5 in the LCD timing spec (defined as > 10ms) */ + mdelay(10); + + /* board_dp_backlight_pwm */ + gpio_direction_output(EXYNOS5_GPIO_B20, 1); + + /* T6 in the LCD timing spec (defined as > 10ms) */ + mdelay(10); + + /* board_dp_backlight_en */ + gpio_direction_output(EXYNOS5_GPIO_X30, 1); +#endif +} + +void exynos_lcd_power_on(void) +{ + int ret; + + debug("%s\n", __func__); + +#ifdef CONFIG_POWER_TPS65090 + /* board_dp_lcd_vdd */ + tps65090_fet_enable(6); /* Enable FET6, lcd panel */ +#endif + + ret = board_dp_bridge_setup(); + if (ret && ret != -ENODEV) + printf("LCD bridge failed to enable: %d\n", ret); +} + #endif diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c deleted file mode 100644 index 014b7bdf890..00000000000 --- a/board/samsung/smdk5250/smdk5250.c +++ /dev/null @@ -1,363 +0,0 @@ -/* - * Copyright (C) 2012 Samsung Electronics - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <cros_ec.h> -#include <fdtdec.h> -#include <asm/io.h> -#include <errno.h> -#include <i2c.h> -#include <lcd.h> -#include <netdev.h> -#include <spi.h> -#include <asm/arch/cpu.h> -#include <asm/arch/dwmmc.h> -#include <asm/arch/gpio.h> -#include <asm/arch/mmc.h> -#include <asm/arch/pinmux.h> -#include <asm/arch/power.h> -#include <asm/arch/sromc.h> -#include <asm/arch/dp_info.h> -#include <power/pmic.h> -#include <power/max77686_pmic.h> - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_SOUND_MAX98095 -static void board_enable_audio_codec(void) -{ - /* Enable MAX98095 Codec */ - gpio_direction_output(EXYNOS5_GPIO_X17, 1); - gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE); -} -#endif - -int exynos_init(void) -{ -#ifdef CONFIG_SOUND_MAX98095 - board_enable_audio_codec(); -#endif - return 0; -} - -int board_eth_init(bd_t *bis) -{ -#ifdef CONFIG_SMC911X - u32 smc_bw_conf, smc_bc_conf; - struct fdt_sromc config; - fdt_addr_t base_addr; - - /* Non-FDT configuration - bank number and timing parameters*/ - config.bank = CONFIG_ENV_SROM_BANK; - config.width = 2; - - config.timing[FDT_SROM_TACS] = 0x01; - config.timing[FDT_SROM_TCOS] = 0x01; - config.timing[FDT_SROM_TACC] = 0x06; - config.timing[FDT_SROM_TCOH] = 0x01; - config.timing[FDT_SROM_TAH] = 0x0C; - config.timing[FDT_SROM_TACP] = 0x09; - config.timing[FDT_SROM_PMC] = 0x01; - base_addr = CONFIG_SMC911X_BASE; - - /* Ethernet needs data bus width of 16 bits */ - if (config.width != 2) { - debug("%s: Unsupported bus width %d\n", __func__, - config.width); - return -1; - } - smc_bw_conf = SROMC_DATA16_WIDTH(config.bank) - | SROMC_BYTE_ENABLE(config.bank); - - smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\ - SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\ - SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\ - SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\ - SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\ - SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\ - SROMC_BC_PMC(config.timing[FDT_SROM_PMC]); - - /* Select and configure the SROMC bank */ - exynos_pinmux_config(PERIPH_ID_SROMC, config.bank); - s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf); - return smc911x_initialize(0, base_addr); -#endif - return 0; -} - -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - printf("\nBoard: SMDK5250\n"); - return 0; -} -#endif - -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) -{ - int err, ret = 0, index, bus_width; - u32 base; - - err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) - debug("SDMMC0 not configured\n"); - ret |= err; - - /*EMMC: dwmmc Channel-0 with 8 bit bus width */ - index = 0; - base = samsung_get_base_mmc() + (0x10000 * index); - bus_width = 8; - err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL); - if (err) - debug("dwmmc Channel-0 init failed\n"); - ret |= err; - - err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err) - debug("SDMMC2 not configured\n"); - ret |= err; - - /*SD: dwmmc Channel-2 with 4 bit bus width */ - index = 2; - base = samsung_get_base_mmc() + (0x10000 * index); - bus_width = 4; - err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL); - if (err) - debug("dwmmc Channel-2 init failed\n"); - ret |= err; - - return ret; -} -#endif - -void board_i2c_init(const void *blob) -{ - int i; - - for (i = 0; i < CONFIG_MAX_I2C_NUM; i++) { - exynos_pinmux_config((PERIPH_ID_I2C0 + i), - PINMUX_FLAG_NONE); - } -} - -#if defined(CONFIG_POWER) -#ifdef CONFIG_POWER_MAX77686 -static int pmic_reg_update(struct pmic *p, int reg, uint regval) -{ - u32 val; - int ret = 0; - - ret = pmic_reg_read(p, reg, &val); - if (ret) { - debug("%s: PMIC %d register read failed\n", __func__, reg); - return -1; - } - val |= regval; - ret = pmic_reg_write(p, reg, val); - if (ret) { - debug("%s: PMIC %d register write failed\n", __func__, reg); - return -1; - } - return 0; -} - -static int max77686_init(void) -{ - struct pmic *p; - - if (pmic_init(I2C_PMIC)) - return -1; - - p = pmic_get("MAX77686_PMIC"); - if (!p) - return -ENODEV; - - if (pmic_probe(p)) - return -1; - - if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN)) - return -1; - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT, - MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V)) - return -1; - - /* VDD_MIF */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT, - MAX77686_BUCK1OUT_1V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK1OUT); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL, - MAX77686_BUCK1CTRL_EN)) - return -1; - - /* VDD_ARM */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1, - MAX77686_BUCK2DVS1_1_3V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK2DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1, - MAX77686_BUCK2CTRL_ON)) - return -1; - - /* VDD_INT */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1, - MAX77686_BUCK3DVS1_1_0125V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK3DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL, - MAX77686_BUCK3CTRL_ON)) - return -1; - - /* VDD_G3D */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1, - MAX77686_BUCK4DVS1_1_2V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK4DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1, - MAX77686_BUCK3CTRL_ON)) - return -1; - - /* VDD_LDO2 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1, - MAX77686_LD02CTRL1_1_5V | EN_LDO)) - return -1; - - /* VDD_LDO3 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1, - MAX77686_LD03CTRL1_1_8V | EN_LDO)) - return -1; - - /* VDD_LDO5 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1, - MAX77686_LD05CTRL1_1_8V | EN_LDO)) - return -1; - - /* VDD_LDO10 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1, - MAX77686_LD10CTRL1_1_8V | EN_LDO)) - return -1; - - return 0; -} -#endif /* CONFIG_POWER_MAX77686 */ - -int exynos_power_init(void) -{ - int ret = 0; - -#ifdef CONFIG_POWER_MAX77686 - ret = max77686_init(); -#endif - return ret; -} -#endif /* CONFIG_POWER */ - -#ifdef CONFIG_LCD -void exynos_cfg_lcd_gpio(void) -{ - - /* For Backlight */ - gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT); - gpio_set_value(EXYNOS5_GPIO_B20, 1); - - /* LCD power on */ - gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT); - gpio_set_value(EXYNOS5_GPIO_X15, 1); - - /* Set Hotplug detect for DP */ - gpio_cfg_pin(EXYNOS5_GPIO_X07, S5P_GPIO_FUNC(0x3)); -} - -void exynos_set_dp_phy(unsigned int onoff) -{ - set_dp_phy_ctrl(onoff); -} - -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 2560, - .vl_row = 1600, - .vl_width = 2560, - .vl_height = 1600, - .vl_clkp = CONFIG_SYS_LOW, - .vl_hsp = CONFIG_SYS_LOW, - .vl_vsp = CONFIG_SYS_LOW, - .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 4, /* LCD_BPP = 2^4, for output conosle on LCD */ - - /* wDP panel timing infomation */ - .vl_hspw = 32, - .vl_hbpd = 80, - .vl_hfpd = 48, - - .vl_vspw = 6, - .vl_vbpd = 37, - .vl_vfpd = 3, - .vl_cmd_allow_len = 0xf, - - .win_id = 3, - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 0, - .reset_delay = 0, - .interface_mode = FIMD_RGB_INTERFACE, - .dp_enabled = 1, -}; - -static struct edp_device_info edp_info = { - .disp_info = { - .h_res = 2560, - .h_sync_width = 32, - .h_back_porch = 80, - .h_front_porch = 48, - .v_res = 1600, - .v_sync_width = 6, - .v_back_porch = 37, - .v_front_porch = 3, - .v_sync_rate = 60, - }, - .lt_info = { - .lt_status = DP_LT_NONE, - }, - .video_info = { - .master_mode = 0, - .bist_mode = DP_DISABLE, - .bist_pattern = NO_PATTERN, - .h_sync_polarity = 0, - .v_sync_polarity = 0, - .interlaced = 0, - .color_space = COLOR_RGB, - .dynamic_range = VESA, - .ycbcr_coeff = COLOR_YCBCR601, - .color_depth = COLOR_8, - }, -}; - -static struct exynos_dp_platform_data dp_platform_data = { - .edp_dev_info = &edp_info, -}; - -void init_panel_info(vidinfo_t *vid) -{ - vid->rgb_mode = MODE_RGB_P; - exynos_set_dp_platform_data(&dp_platform_data); -} -#endif diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c index 92075229535..183c52248a3 100644 --- a/board/samsung/smdk5420/smdk5420.c +++ b/board/samsung/smdk5420/smdk5420.c @@ -42,9 +42,6 @@ int exynos_init(void) #ifdef CONFIG_LCD void cfg_lcd_gpio(void) { - struct exynos5_gpio_part1 *gpio1 = - (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1(); - /* For Backlight */ gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_OUTPUT); gpio_set_value(EXYNOS5420_GPIO_B20, 1); diff --git a/board/ti/am43xx/Makefile b/board/ti/am43xx/Makefile index cb5fe889010..36ecb302c1f 100644 --- a/board/ti/am43xx/Makefile +++ b/board/ti/am43xx/Makefile @@ -6,7 +6,7 @@ # SPDX-License-Identifier: GPL-2.0+ # -ifdef CONFIG_SPL_BUILD +ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),) obj-y := mux.o endif diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index d7449770a3f..71af1ae7c89 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -19,6 +19,7 @@ #include <asm/arch/gpio.h> #include <asm/emif.h> #include "board.h" +#include <power/tps65218.h> #include <miiphy.h> #include <cpsw.h> @@ -70,7 +71,7 @@ static int read_eeprom(struct am43xx_board_id *header) return 0; } -#ifdef CONFIG_SPL_BUILD +#ifndef CONFIG_SKIP_LOWLEVEL_INIT #define NUM_OPPS 6 @@ -254,13 +255,6 @@ void emif_get_ext_phy_ctrl_const_regs(const u32 **regs, u32 *size) const struct dpll_params *get_dpll_ddr_params(void) { - struct am43xx_board_id header; - - enable_i2c0_pin_mux(); - i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); - if (read_eeprom(&header) < 0) - puts("Could not get board ID.\n"); - if (board_is_eposevm()) return &epos_evm_dpll_ddr; else if (board_is_gpevm()) @@ -302,7 +296,10 @@ static u32 get_sys_clk_index(void) static int get_opp_offset(int max_off, int min_off) { struct ctrl_stat *ctrl = (struct ctrl_stat *)CTRL_BASE; - int opp = readl(&ctrl->dev_attr), offset, i; + int opp, offset, i; + + /* Bits 0:11 are defined to be the MPU_MAX_FREQ */ + opp = readl(&ctrl->dev_attr) & ~0xFFFFF000; for (i = max_off; i >= min_off; i--) { offset = opp & (1 << i); @@ -335,6 +332,46 @@ const struct dpll_params *get_dpll_per_params(void) return &dpll_per[ind]; } +void scale_vcores(void) +{ + const struct dpll_params *mpu_params; + int mpu_vdd; + struct am43xx_board_id header; + + enable_i2c0_pin_mux(); + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); + if (read_eeprom(&header) < 0) + puts("Could not get board ID.\n"); + + /* Get the frequency */ + mpu_params = get_dpll_mpu_params(); + + if (i2c_probe(TPS65218_CHIP_PM)) + return; + + if (mpu_params->m == 1000) { + mpu_vdd = TPS65218_DCDC_VOLT_SEL_1330MV; + } else if (mpu_params->m == 600) { + mpu_vdd = TPS65218_DCDC_VOLT_SEL_1100MV; + } else { + puts("Unknown MPU clock, not scaling\n"); + return; + } + + /* Set DCDC1 (CORE) voltage to 1.1V */ + if (tps65218_voltage_update(TPS65218_DCDC1, + TPS65218_DCDC_VOLT_SEL_1100MV)) { + puts("tps65218_voltage_update failure\n"); + return; + } + + /* Set DCDC2 (MPU) voltage */ + if (tps65218_voltage_update(TPS65218_DCDC2, mpu_vdd)) { + puts("tps65218_voltage_update failure\n"); + return; + } +} + void set_uart_mux_conf(void) { enable_uart0_pin_mux(); |