summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
Diffstat (limited to 'doc')
-rw-r--r--doc/README.bitbangMII18
-rw-r--r--doc/README.drivers.eth2
-rw-r--r--doc/README.kwbimage4
3 files changed, 12 insertions, 12 deletions
diff --git a/doc/README.bitbangMII b/doc/README.bitbangMII
index edd085630f1..0a2fa48a56f 100644
--- a/doc/README.bitbangMII
+++ b/doc/README.bitbangMII
@@ -6,7 +6,7 @@ buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
-CONFIG_BITBANGMII - Enable the miiphybb driver
+CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
@@ -19,7 +19,7 @@ MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
-MDC(v) - Write v on the MDC pin
+MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
@@ -30,17 +30,17 @@ the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
-char name[] - The symbolic name that must be equal to the MII bus
- registered name
-int (*init)() - Initialization function called at startup time (just
- before the Ethernet initialization)
+char name[] - The symbolic name that must be equal to the MII bus
+ registered name
+int (*init)() - Initialization function called at startup time (just
+ before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
-int (*delay)() - Delay function
-void *priv - Private data used by board specific code
+int (*delay)() - Delay function
+void *priv - Private data used by board specific code
The board code will look like:
@@ -50,7 +50,7 @@ struct bb_miiphy_bus bb_miiphy_buses[] = {
...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
- sizeof(bb_miiphy_buses[0]);
+ sizeof(bb_miiphy_buses[0]);
2009 Industrie Dial Face S.p.A.
Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
diff --git a/doc/README.drivers.eth b/doc/README.drivers.eth
index e06d3ad44ba..e73e462c8c2 100644
--- a/doc/README.drivers.eth
+++ b/doc/README.drivers.eth
@@ -88,7 +88,7 @@ The return value for this function should be as follows:
< 0 - failure (hardware failure, not probe failure)
>=0 - number of interfaces detected
-You might notice that many drivers seem to use xxx_initialize() rather than
+You might notice that many drivers seem to use xxx_initialize() rather than
xxx_register(). This is the old naming convention and should be avoided as it
causes confusion with the driver-specific init function.
diff --git a/doc/README.kwbimage b/doc/README.kwbimage
index 2a5b3b3be5d..6dd942f1097 100644
--- a/doc/README.kwbimage
+++ b/doc/README.kwbimage
@@ -17,12 +17,12 @@ Command syntax:
to list the kwb image file details
./tools/mkimage -n <board specific configuration file> \
- -T kwbimage -a <start address> -e <execution address> \
+ -T kwbimage -a <start address> -e <execution address> \
-d <input_raw_binary> <output_kwboot_file>
for ex.
./tools/mkimage -n ./board/Marvell/openrd_base/kwbimage.cfg \
- -T kwbimage -a 0x00600000 -e 0x00600000 \
+ -T kwbimage -a 0x00600000 -e 0x00600000 \
-d u-boot.bin u-boot.kwb
kwimage support available with mkimage utility will generate kirkwood boot