diff options
Diffstat (limited to 'include/configs/GEN860T.h')
| -rw-r--r-- | include/configs/GEN860T.h | 198 |
1 files changed, 99 insertions, 99 deletions
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h index 422ed32aaaa..a399d22a7af 100644 --- a/include/configs/GEN860T.h +++ b/include/configs/GEN860T.h @@ -64,7 +64,7 @@ /* * Set allowable console baud rates */ -#define CFG_BAUDRATE_TABLE { 9600, \ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, \ 19200, \ 38400, \ 57600, \ @@ -74,7 +74,7 @@ /* * Print console information */ -#undef CFG_CONSOLE_INFO_QUIET +#undef CONFIG_SYS_CONSOLE_INFO_QUIET /* * Set the autoboot delay in seconds. A delay of -1 disables autoboot @@ -101,12 +101,12 @@ * for downloads */ #undef CONFIG_LOADS_ECHO -#define CFG_LOADS_BAUD_CHANGE +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* * Set default load address for tftp network downloads */ -#define CFG_TFTP_LOADADDR 0x01000000 +#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* * Turn off the watchdog timer @@ -127,7 +127,7 @@ * Reset address. We pick an address such that when an instruction * is executed at that address, a machine check exception occurs */ -#define CFG_RESET_ADDRESS ((ulong) -1) +#define CONFIG_SYS_RESET_ADDRESS ((ulong) -1) /* * BOOTP options @@ -145,7 +145,7 @@ * MII address is hardwired on the board to zero. */ #define CONFIG_FEC_ENET -#define CFG_DISCOVER_PHY +#define CONFIG_SYS_DISCOVER_PHY #define CONFIG_MII #define CONFIG_MII_INIT 1 #define CONFIG_PHY_ADDR 0 @@ -162,11 +162,11 @@ * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to * the MPC860T I2C interface. */ -#define CFG_I2C_EEPROM_ADDR 0x50 -#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */ -#define CFG_ENV_EEPROM_SIZE (32 * 1024) +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */ +#define CONFIG_ENV_EEPROM_SIZE (32 * 1024) /* * Enable I2C and select the hardware/software driver @@ -175,8 +175,8 @@ #undef CONFIG_SOFT_I2C /* Bit-banged I2C */ #ifdef CONFIG_HARD_I2C -#define CFG_I2C_SPEED 100000 /* clock speed in Hz */ -#define CFG_I2C_SLAVE 0xFE /* I2C slave address */ +#define CONFIG_SYS_I2C_SPEED 100000 /* clock speed in Hz */ +#define CONFIG_SYS_I2C_SLAVE 0xFE /* I2C slave address */ #endif #ifdef CONFIG_SOFT_I2C @@ -208,7 +208,7 @@ * length of time, so we use an external RTC on the I2C bus instead. */ #define CONFIG_RTC_DS1337 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 #else /* @@ -220,11 +220,11 @@ /* * Power On Self Test support */ -#define CONFIG_POST ( CFG_POST_CACHE | \ - CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_SPR ) +#define CONFIG_POST ( CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_SPR ) /* @@ -277,7 +277,7 @@ #define CONFIG_FPGA #define CONFIG_FPGA_XILINX #define CONFIG_FPGA_VIRTEX2 -#define CFG_FPGA_PROG_FEEDBACK +#define CONFIG_SYS_FPGA_PROG_FEEDBACK #define CONFIG_NAND_LEGACY @@ -285,64 +285,64 @@ /* * Verbose help from command monitor. */ -#define CFG_LONGHELP +#define CONFIG_SYS_LONGHELP #if !defined(CONFIG_SC) -#define CFG_PROMPT "B2> " +#define CONFIG_SYS_PROMPT "B2> " #else -#define CFG_PROMPT "SC> " +#define CONFIG_SYS_PROMPT "SC> " #endif /* * Use the "hush" command parser */ -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* * Set buffer size for console I/O */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 +#define CONFIG_SYS_CBSIZE 1024 #else -#define CFG_CBSIZE 256 +#define CONFIG_SYS_CBSIZE 256 #endif /* * Print buffer size */ -#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* * Maximum number of arguments that a command can accept */ -#define CFG_MAXARGS 16 +#define CONFIG_SYS_MAXARGS 16 /* * Boot argument buffer size */ -#define CFG_BARGSIZE CFG_CBSIZE +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* * Default memory test range */ -#define CFG_MEMTEST_START 0x0100000 -#define CFG_MEMTEST_END (CFG_MEMTEST_START + (128 * 1024)) +#define CONFIG_SYS_MEMTEST_START 0x0100000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (128 * 1024)) /* * Select the more full-featured memory test */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST /* * Default load address */ -#define CFG_LOAD_ADDR 0x01000000 +#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* * Set decrementer frequency (1 ms ticks) */ -#define CFG_HZ 1000 +#define CONFIG_SYS_HZ 1000 /* * Device memory map (after SDRAM remap to 0x0): @@ -363,7 +363,7 @@ /* * Base addresses and block sizes */ -#define CFG_IMMR 0xFF000000 +#define CONFIG_SYS_IMMR 0xFF000000 #define SDRAM_BASE 0x00000000 #define SDRAM_SIZE (64 * 1024 * 1024) @@ -386,27 +386,27 @@ /* * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CFG_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CONFIG_SYS_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_INIT_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE SDRAM_BASE +#define CONFIG_SYS_SDRAM_BASE SDRAM_BASE /* * FLASH organization */ -#define CFG_FLASH_BASE FLASH_BASE -#define CFG_FLASH_SIZE FLASH_SIZE -#define CFG_FLASH_SECT_SIZE (128 * 1024) -#define CFG_MAX_FLASH_BANKS 1 -#define CFG_MAX_FLASH_SECT 128 +#define CONFIG_SYS_FLASH_BASE FLASH_BASE +#define CONFIG_SYS_FLASH_SIZE FLASH_SIZE +#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* * The timeout values are for an entire chip and are in milliseconds. @@ -415,60 +415,60 @@ * case VCC and temp after 100K programming cycles. It works out * to 280 minutes (might as well be forever). */ -#define CFG_FLASH_ERASE_TOUT (CFG_MAX_FLASH_SECT * 5000) -#define CFG_FLASH_WRITE_TOUT (CFG_MAX_FLASH_SECT * 128 * 1024 * 1) +#define CONFIG_SYS_FLASH_ERASE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 5000) +#define CONFIG_SYS_FLASH_WRITE_TOUT (CONFIG_SYS_MAX_FLASH_SECT * 128 * 1024 * 1) /* * Allow direct writes to FLASH from tftp transfers (** dangerous **) */ -#define CFG_DIRECT_FLASH_TFTP +#define CONFIG_SYS_DIRECT_FLASH_TFTP /* * Reserve memory for U-Boot. */ -#define CFG_MAX_UBOOT_SECTS 4 -#define CFG_MONITOR_LEN (CFG_MAX_UBOOT_SECTS * CFG_FLASH_SECT_SIZE) -#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CONFIG_SYS_MAX_UBOOT_SECTS 4 +#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_MAX_UBOOT_SECTS * CONFIG_SYS_FLASH_SECT_SIZE) +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* * Select environment placement. NOTE that u-boot.lds must * be edited if this is changed! */ -#undef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_IS_IN_EEPROM +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_IS_IN_EEPROM -#if defined(CFG_ENV_IS_IN_EEPROM) -#define CFG_ENV_SIZE (2 * 1024) -#define CFG_ENV_OFFSET (CFG_ENV_EEPROM_SIZE - (8 * 1024)) +#if defined(CONFIG_ENV_IS_IN_EEPROM) +#define CONFIG_ENV_SIZE (2 * 1024) +#define CONFIG_ENV_OFFSET (CONFIG_ENV_EEPROM_SIZE - (8 * 1024)) #else -#define CFG_ENV_SIZE 0x1000 -#define CFG_ENV_SECT_SIZE CFG_FLASH_SECT_SIZE +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SIZE /* * This ultimately gets passed right into the linker script, so we have to * use a number :( */ -#define CFG_ENV_OFFSET 0x060000 +#define CONFIG_ENV_OFFSET 0x060000 #endif /* * Reserve memory for malloc() */ -#define CFG_MALLOC_LEN (128 * 1024) +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 * 1024 * 1024) +#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* * Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 4 /* log base 2 of above value */ +#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of above value */ #endif /*------------------------------------------------------------------------ @@ -479,7 +479,7 @@ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) -#define CFG_SYPCR ( SYPCR_SWTC | \ +#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ SYPCR_BMT | \ SYPCR_BME | \ SYPCR_SWF | \ @@ -488,7 +488,7 @@ SYPCR_SWP \ ) #else -#define CFG_SYPCR ( SYPCR_SWTC | \ +#define CONFIG_SYS_SYPCR ( SYPCR_SWTC | \ SYPCR_BMT | \ SYPCR_BME | \ SYPCR_SWF | \ @@ -501,7 +501,7 @@ *----------------------------------------------------------------------- * Set debug pin mux, enable SPKROUT and GPLB5*. */ -#define CFG_SIUMCR ( SIUMCR_DBGC11 | \ +#define CONFIG_SYS_SIUMCR ( SIUMCR_DBGC11 | \ SIUMCR_DBPC11 | \ SIUMCR_MLRC11 | \ SIUMCR_GB5E \ @@ -512,7 +512,7 @@ *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freeze enabled */ -#define CFG_TBSCR ( TBSCR_REFA | \ +#define CONFIG_SYS_TBSCR ( TBSCR_REFA | \ TBSCR_REFB | \ TBSCR_TBF \ ) @@ -521,7 +521,7 @@ * RTCSC - Real-Time Clock Status and Control Register UM 11-27 *----------------------------------------------------------------------- */ -#define CFG_RTCSC ( RTCSC_SEC | \ +#define CONFIG_SYS_RTCSC ( RTCSC_SEC | \ RTCSC_ALR | \ RTCSC_RTF | \ RTCSC_RTE \ @@ -532,7 +532,7 @@ *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ -#define CFG_PISCR ( PISCR_PS | \ +#define CONFIG_SYS_PISCR ( PISCR_PS | \ PISCR_PITF \ ) @@ -542,7 +542,7 @@ * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit. Set MF for 1:2:1 mode. */ -#define CFG_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \ +#define CONFIG_SYS_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \ PLPRCR_SPLSS | \ PLPRCR_TEXPS | \ PLPRCR_TMIST \ @@ -557,7 +557,7 @@ #define SCCR_MASK SCCR_EBDF11 #if !defined(CONFIG_SC) -#define CFG_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ +#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ SCCR_COM00 | /* full strength CLKOUT */ \ SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ @@ -565,7 +565,7 @@ SCCR_DFNH000 \ ) #else -#define CFG_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ +#define CONFIG_SYS_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ SCCR_COM00 | /* full strength CLKOUT */ \ SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ @@ -581,7 +581,7 @@ *----------------------------------------------------------------------- * Mask all events that can cause entry into debug mode */ -#define CFG_DER 0 +#define CONFIG_SYS_DER 0 /* * Initialize Memory Controller: @@ -593,13 +593,13 @@ /* * Flash address mask */ -#define CFG_PRELIM_OR_AM 0xfe000000 +#define CONFIG_SYS_PRELIM_OR_AM 0xfe000000 /* * FLASH timing: * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */ -#define CFG_OR_TIMING_FLASH ( OR_CSNT_SAM | \ +#define CONFIG_SYS_OR_TIMING_FLASH ( OR_CSNT_SAM | \ OR_ACS_DIV2 | \ OR_BI | \ OR_SCY_2_CLK | \ @@ -607,11 +607,11 @@ OR_EHTR \ ) -#define CFG_OR0_PRELIM ( CFG_PRELIM_OR_AM | \ - CFG_OR_TIMING_FLASH \ +#define CONFIG_SYS_OR0_PRELIM ( CONFIG_SYS_PRELIM_OR_AM | \ + CONFIG_SYS_OR_TIMING_FLASH \ ) -#define CFG_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \ +#define CONFIG_SYS_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \ BR_MS_GPCM | \ BR_PS_8 | \ BR_V \ @@ -620,12 +620,12 @@ /* * SDRAM configuration */ -#define CFG_OR1_AM 0xfc000000 -#define CFG_OR1 ( (CFG_OR1_AM & OR_AM_MSK) | \ +#define CONFIG_SYS_OR1_AM 0xfc000000 +#define CONFIG_SYS_OR1 ( (CONFIG_SYS_OR1_AM & OR_AM_MSK) | \ OR_CSNT_SAM \ ) -#define CFG_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \ BR_MS_UPMA | \ BR_PS_32 | \ BR_V \ @@ -635,17 +635,17 @@ * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank * of 256 MBit SDRAM */ -#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 +#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* * Periodic timer for refresh @ 33 MHz system clock */ -#define CFG_MAMR_PTA 64 +#define CONFIG_SYS_MAMR_PTA 64 /* * MAMR settings for SDRAM */ -#define CFG_MAMR_8COL ( (CFG_MAMR_PTA << MAMR_PTA_SHIFT) | \ +#define CONFIG_SYS_MAMR_8COL ( (CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | \ MAMR_PTAE | \ MAMR_AMA_TYPE_1 | \ MAMR_DSA_1_CYCL | \ @@ -660,7 +660,7 @@ * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1, * no burst. */ -#define CFG_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ +#define CONFIG_SYS_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ OR_CSNT_SAM | \ OR_ACS_DIV2 | \ OR_BI | \ @@ -669,7 +669,7 @@ OR_EHTR \ ) -#define CFG_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \ BR_PS_8 | \ BR_MS_GPCM | \ BR_V \ @@ -683,12 +683,12 @@ * the cycle will still complete even if there is a configuration * error that prevents TA from asserting on FPGA accesss. */ -#define CFG_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \ +#define CONFIG_SYS_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \ OR_SCY_15_CLK | \ OR_BI \ ) -#define CFG_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \ BR_PS_32 | \ BR_MS_GPCM | \ BR_V \ @@ -698,12 +698,12 @@ * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge * of GCLK1_50 */ -#define CFG_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ +#define CONFIG_SYS_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ OR_G5LS | \ OR_BI \ ) -#define CFG_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \ BR_PS_8 | \ BR_MS_UPMB | \ BR_V \ @@ -717,7 +717,7 @@ * the cycle will still complete even if there is a configuration * error that prevents TA from asserting on FPGA accesss. */ -#define CFG_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ +#define CONFIG_SYS_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ OR_SCY_15_CLK | \ OR_EHTR | \ OR_TRLX | \ @@ -725,7 +725,7 @@ OR_BI \ ) -#define CFG_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \ +#define CONFIG_SYS_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \ BR_PS_16 | \ BR_MS_GPCM | \ BR_V \ @@ -741,10 +741,10 @@ * Disk On Chip (millenium) configuration */ #if !defined(CONFIG_SC) -#define CFG_MAX_DOC_DEVICE 1 -#undef CFG_DOC_SUPPORT_2000 -#define CFG_DOC_SUPPORT_MILLENNIUM -#undef CFG_DOC_PASSIVE_PROBE +#define CONFIG_SYS_MAX_DOC_DEVICE 1 +#undef CONFIG_SYS_DOC_SUPPORT_2000 +#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM +#undef CONFIG_SYS_DOC_PASSIVE_PROBE #endif /* |