diff options
Diffstat (limited to 'include/configs/MPC832XEMDS.h')
| -rw-r--r-- | include/configs/MPC832XEMDS.h | 393 |
1 files changed, 197 insertions, 196 deletions
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 401d0afc4d0..bc56e682a75 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -47,7 +47,7 @@ /* * Hardware Reset Configuration Word */ -#define CFG_HRCW_LOW (\ +#define CONFIG_SYS_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_2X1 |\ HRCWL_VCO_1X2 |\ @@ -58,7 +58,7 @@ HRCWL_CE_TO_PLL_1X3) #ifdef CONFIG_PCISLAVE -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_AGENT |\ HRCWH_PCI1_ARBITER_DISABLE |\ HRCWH_CORE_ENABLE |\ @@ -69,7 +69,7 @@ HRCWH_BIG_ENDIAN |\ HRCWH_LALE_NORMAL) #else -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_CORE_ENABLE |\ @@ -84,7 +84,7 @@ /* * System IO Config */ -#define CFG_SICRL 0x00000000 +#define CONFIG_SYS_SICRL 0x00000000 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ #define CONFIG_BOARD_EARLY_INIT_R @@ -92,15 +92,15 @@ /* * IMMR new address */ -#define CFG_IMMR 0xE0000000 +#define CONFIG_SYS_IMMR 0xE0000000 /* * DDR Setup */ -#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ #undef CONFIG_SPD_EEPROM #if defined(CONFIG_SPD_EEPROM) @@ -110,105 +110,106 @@ #else /* Manually set up DDR parameters */ -#define CFG_DDR_SIZE 128 /* MB */ -#define CFG_DDR_CS0_CONFIG 0x80840102 -#define CFG_DDR_TIMING_0 0x00220802 -#define CFG_DDR_TIMING_1 0x3935d322 -#define CFG_DDR_TIMING_2 0x0f9048ca -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_CLK_CNTL 0x02000000 -#define CFG_DDR_MODE 0x44400232 -#define CFG_DDR_MODE2 0x8000c000 -#define CFG_DDR_INTERVAL 0x03200064 -#define CFG_DDR_CS0_BNDS 0x00000007 -#define CFG_DDR_SDRAM_CFG 0x43080000 -#define CFG_DDR_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80840102 +#define CONFIG_SYS_DDR_TIMING_0 0x00220802 +#define CONFIG_SYS_DDR_TIMING_1 0x3935d322 +#define CONFIG_SYS_DDR_TIMING_2 0x0f9048ca +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 +#define CONFIG_SYS_DDR_MODE 0x44400232 +#define CONFIG_SYS_DDR_MODE2 0x8000c000 +#define CONFIG_SYS_DDR_INTERVAL 0x03200064 +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080000 +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 #endif /* * Memory test */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00000000 /* memtest region */ -#define CFG_MEMTEST_END 0x00100000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00100000 /* * The reserved memory */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif -/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* * Initial RAM Base Address Setup */ -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup */ -#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) -#define CFG_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* * FLASH on the Local Bus */ -#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ -#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ -#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ -#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ +#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM +#undef CONFIG_SYS_FLASH_CHECKSUM /* * BCSR on the Local Bus */ -#define CFG_BCSR 0xF8000000 -#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ -#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ +#define CONFIG_SYS_BCSR 0xF8000000 +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR /* Access window base at BCSR base */ +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ -#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ -#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ +#define CONFIG_SYS_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ /* * SDRAM on the Local Bus */ -#undef CFG_LB_SDRAM /* The board has not SRDAM on local bus */ +#undef CONFIG_SYS_LB_SDRAM /* The board has not SRDAM on local bus */ -#ifdef CFG_LB_SDRAM -#define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ -#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ +#ifdef CONFIG_SYS_LB_SDRAM +#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ -#define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE -#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ /* * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. * * For BR2, need: * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 @@ -220,14 +221,14 @@ * 0 4 8 12 16 20 24 28 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 * - * CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into * the top 17 bits of BR2. */ -#define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ +#define CONFIG_SYS_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ /* - * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. * * For OR2, need: * 64MB mask for AM, OR2[0:7] = 1111 1100 @@ -240,80 +241,80 @@ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 */ -#define CFG_OR2_PRELIM 0xfc006901 +#define CONFIG_SYS_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ +#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ /* * LSDMR masks */ -#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) -#define CFG_LBC_LSDMR_COMMON 0x0063b723 +#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723 /* * SDRAM Controller configuration sequence. */ -#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_PCHALL) -#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_MRW) -#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_NORMAL) +#define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \ + | CONFIG_SYS_LBC_LSDMR_OP_PCHALL) +#define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \ + | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) +#define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \ + | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) +#define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \ + | CONFIG_SYS_LBC_LSDMR_OP_MRW) +#define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \ + | CONFIG_SYS_LBC_LSDMR_OP_NORMAL) #endif /* * Windows to access PIB via local bus */ -#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ -#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ +#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ /* * CS2 on Local Bus, to PIB */ -#define CFG_BR2_PRELIM 0xf8008801 /* CS2 base address at 0xf8008000 */ -#define CFG_OR2_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ +#define CONFIG_SYS_BR2_PRELIM 0xf8008801 /* CS2 base address at 0xf8008000 */ +#define CONFIG_SYS_OR2_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * CS3 on Local Bus, to PIB */ -#define CFG_BR3_PRELIM 0xf8010801 /* CS3 base address at 0xf8010000 */ -#define CFG_OR3_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ +#define CONFIG_SYS_BR3_PRELIM 0xf8010801 /* CS3 base address at 0xf8010000 */ +#define CONFIG_SYS_OR3_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) -#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ @@ -325,34 +326,34 @@ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 /* * Config on-board RTC */ #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI_MEM_BASE 0x80000000 -#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE -#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_MMIO_BASE 0x90000000 -#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE -#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_IO_BASE 0x00000000 -#define CFG_PCI_IO_PHYS 0xE0300000 -#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE +#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ -#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE -#define CFG_PCI_SLV_MEM_BUS 0x00000000 -#define CFG_PCI_SLV_MEM_SIZE 0x80000000 +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 +#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 #ifdef CONFIG_PCI @@ -362,7 +363,7 @@ #undef CONFIG_EEPRO100 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ #endif /* CONFIG_PCI */ @@ -380,42 +381,42 @@ #define CONFIG_UEC_ETH1 /* ETH3 */ #ifdef CONFIG_UEC_ETH1 -#define CFG_UEC1_UCC_NUM 2 /* UCC3 */ -#define CFG_UEC1_RX_CLK QE_CLK9 -#define CFG_UEC1_TX_CLK QE_CLK10 -#define CFG_UEC1_ETH_TYPE FAST_ETH -#define CFG_UEC1_PHY_ADDR 3 -#define CFG_UEC1_INTERFACE_MODE ENET_100_MII +#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 +#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 3 +#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_MII #endif #define CONFIG_UEC_ETH2 /* ETH4 */ #ifdef CONFIG_UEC_ETH2 -#define CFG_UEC2_UCC_NUM 3 /* UCC4 */ -#define CFG_UEC2_RX_CLK QE_CLK7 -#define CFG_UEC2_TX_CLK QE_CLK8 -#define CFG_UEC2_ETH_TYPE FAST_ETH -#define CFG_UEC2_PHY_ADDR 4 -#define CFG_UEC2_INTERFACE_MODE ENET_100_MII +#define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 +#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 4 +#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_100_MII #endif /* * Environment */ -#ifndef CFG_RAMBOOT - #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) - #define CFG_ENV_SECT_SIZE 0x20000 - #define CFG_ENV_SIZE 0x2000 +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_IS_IN_FLASH 1 + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) + #define CONFIG_ENV_SECT_SIZE 0x20000 + #define CONFIG_ENV_SIZE 0x2000 #else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ - #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) - #define CFG_ENV_SIZE 0x2000 + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -439,7 +440,7 @@ #define CONFIG_CMD_PCI #endif -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif @@ -450,34 +451,34 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup */ -#define CFG_HID0_INIT 0x000000000 -#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK -#define CFG_HID2 HID2_HBE +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CONFIG_SYS_HID2 HID2_HBE /* * MMU Setup @@ -486,64 +487,64 @@ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ -#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT0L CFG_IBAT0L -#define CFG_DBAT0U CFG_IBAT0U +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U /* IMMRBAR & PCI IO: cache-inhibit and guarded */ -#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) -#define CFG_DBAT1L CFG_IBAT1L -#define CFG_DBAT1U CFG_IBAT1U +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U /* BCSR: cache-inhibit and guarded */ -#define CFG_IBAT2L (CFG_BCSR | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT2U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT2L CFG_IBAT2L -#define CFG_DBAT2U CFG_IBAT2U +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U /* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT3U CFG_IBAT3U +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U -#define CFG_IBAT4L (0) -#define CFG_IBAT4U (0) -#define CFG_DBAT4L CFG_IBAT4L -#define CFG_DBAT4U CFG_IBAT4U +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* Stack in dcache: cacheable, no memory coherence */ -#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) -#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT5L CFG_IBAT5L -#define CFG_DBAT5U CFG_IBAT5U +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U #ifdef CONFIG_PCI /* PCI MEM space: cacheable */ -#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U /* PCI MMIO space: cache-inhibit and guarded */ -#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #else -#define CFG_IBAT6L (0) -#define CFG_IBAT6U (0) -#define CFG_IBAT7L (0) -#define CFG_IBAT7U (0) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #endif /* |