diff options
Diffstat (limited to 'include/configs/W7OLMG.h')
| -rw-r--r-- | include/configs/W7OLMG.h | 317 |
1 files changed, 0 insertions, 317 deletions
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h deleted file mode 100644 index 2a38116dd16..00000000000 --- a/include/configs/W7OLMG.h +++ /dev/null @@ -1,317 +0,0 @@ -/* - * (C) Copyright 2001 - * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ -#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ -#define CONFIG_W7OLMG 1 /* ...specifically an LMG */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ - -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#if 1 -#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ -#else -#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ -#endif - -#undef CONFIG_BOOTARGS - -#define CONFIG_LOADADDR F0080000 - -#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_IPADDR 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_SERVERIP 192.168.1.2 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ - -#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_BSP -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_DTT - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ - -#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ -#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ -#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ -#ifdef CONFIG_SYS_HUSH_PARSER -#endif -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 384000 - - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE {9600} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ -#define CONFIG_PCI_PNP /* pci plug-and-play */ -/* resource configuration */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Set up values for external bus controller - * used by cpu_init.c - *----------------------------------------------------------------------- - */ - /* use PerWE instead of PCI_INT ( these functions share a pin ) */ -#define CONFIG_USE_PERWE 1 - -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* bank 0 is boot flash */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 -/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 - -/* bank 1 is main flash */ -/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB1AP 0x04850240 -/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ -#define CONFIG_SYS_EBC_PB1CR 0xF00FC000 - -/* bank 2 is RTC/NVRAM */ -/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_EBC_PB2AP 0x03000440 -/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB2CR 0xFC018000 - -/* bank 3 is FPGA 0 */ -/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ -#define CONFIG_SYS_EBC_PB3AP 0x02000400 -/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB3CR 0xFD01A000 - -/* bank 4 is SAM 8 bit range */ -/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ -#define CONFIG_SYS_EBC_PB4AP 0x02840380 -/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ -#define CONFIG_SYS_EBC_PB4CR 0xFE878000 - -/* bank 5 is SAM 16 bit range */ -/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ -#define CONFIG_SYS_EBC_PB5AP 0x05040d80 -/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ -#define CONFIG_SYS_EBC_PB5CR 0xFD87A000 - -/* bank 6 is unused */ -/* PB6AP = 0 */ -#define CONFIG_SYS_EBC_PB6AP 0x00000000 -/* PB6CR = 0 */ -#define CONFIG_SYS_EBC_PB6CR 0x00000000 - -/* bank 7 is LED register */ -/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 -/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ -#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ - -#if 1 /* Use NVRAM for environment variables */ -/*----------------------------------------------------------------------- - * NVRAM organization - */ -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ -#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ -/*define CONFIG_ENV_ADDR \ - (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ -#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR - -#else /* Use Boot Flash for environment variables */ -/*----------------------------------------------------------------------- - * Flash EEPROM for environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */ - -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ -#endif - -/*----------------------------------------------------------------------- - * I2C EEPROM (ATMEL 24C04N) - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_I2C_MULTI_EEPROMS -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ - -/* - * Init Memory Controller: - */ -#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in RAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * FPGA(s) configuration - */ -#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ -#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ -#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ -#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ -#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ - -#endif /* __CONFIG_H */ |