diff options
Diffstat (limited to 'include/configs/XPEDITE1K.h')
| -rw-r--r-- | include/configs/XPEDITE1K.h | 132 |
1 files changed, 66 insertions, 66 deletions
diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h index d533b17afd0..569bb9052e6 100644 --- a/include/configs/XPEDITE1K.h +++ b/include/configs/XPEDITE1K.h @@ -38,29 +38,29 @@ #define CONFIG_440 1 #define CONFIG_440GX 1 /* 440 GX */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ +#undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /* POST support */ -#define CONFIG_POST (CFG_POST_RTC | \ - CFG_POST_I2C) +#define CONFIG_POST (CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_I2C) /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ -#define CFG_MONITOR_BASE CFG_FLASH_BASE /* start of monitor */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* start of monitor */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) -#define CFG_GPIO_BASE (CFG_PERIPHERAL_BASE + 0x00000700) +#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) +#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) #define USR_LED0 0x00000080 #define USR_LED1 0x00000100 @@ -71,33 +71,33 @@ extern unsigned long in32(unsigned int); extern void out32(unsigned int, unsigned long); -#define LED0_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED0)) -#define LED1_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED1)) -#define LED2_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED2)) -#define LED3_ON() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) & ~USR_LED3)) +#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0)) +#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1)) +#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2)) +#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3)) -#define LED0_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED0)) -#define LED1_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED1)) -#define LED2_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED2)) -#define LED3_OFF() out32(CFG_GPIO_BASE, (in32(CFG_GPIO_BASE) | USR_LED3)) +#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0)) +#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1)) +#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2)) +#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3)) #endif /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ /*----------------------------------------------------------------------- * Serial Port @@ -105,7 +105,7 @@ extern void out32(unsigned int, unsigned long); #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_BAUDRATE 9600 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} /*----------------------------------------------------------------------- @@ -115,23 +115,23 @@ extern void out32(unsigned int, unsigned long); * The DS1743 code assumes this condition (i.e. -- it assumes the base * address for the RTC registers is: * - * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE + * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE * *----------------------------------------------------------------------*/ /* TBS: Xpedite 1000 has STMicro M41T00 via IIC */ #define CONFIG_RTC_M41T11 1 -#define CFG_I2C_RTC_ADDR 0x68 -#define CFG_M41T11_BASE_YEAR 2000 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 2000 /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 8 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /*----------------------------------------------------------------------- * DDR SDRAM @@ -144,9 +144,9 @@ extern void out32(unsigned int, unsigned long); *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7f -#define CFG_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7f +#define CONFIG_SYS_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} /* Don't probe these addrs */ /*----------------------------------------------------------------------- * Environment @@ -154,10 +154,10 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_ENV_IS_IN_EEPROM 1 #define CONFIG_ENV_SIZE 0x100 /* Size of Environment vars */ #define CONFIG_ENV_OFFSET 0x100 -#define CFG_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_BOOTARGS "root=/dev/hda1 " #define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ @@ -165,7 +165,7 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_BAUDRATE 9600 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address phy0 not populated */ @@ -175,7 +175,7 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */ @@ -214,24 +214,24 @@ extern void out32(unsigned int, unsigned long); /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- @@ -242,20 +242,20 @@ extern void out32(unsigned int, unsigned long); #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#define CFG_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions |