diff options
Diffstat (limited to 'include/configs/katmai.h')
| -rw-r--r-- | include/configs/katmai.h | 152 |
1 files changed, 76 insertions, 76 deletions
diff --git a/include/configs/katmai.h b/include/configs/katmai.h index b0dc175afed..58694cca4b1 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -38,7 +38,7 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ +#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /* * Enable this board for more than 2GB of SDRAM @@ -60,53 +60,53 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ -#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ +#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE -#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ -#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ +#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ +#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ +#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ -#define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE1_CFGBASE 0xc1000000 -#define CFG_PCIE2_CFGBASE 0xc2000000 -#define CFG_PCIE0_XCFGBASE 0xc3000000 -#define CFG_PCIE1_XCFGBASE 0xc3001000 -#define CFG_PCIE2_XCFGBASE 0xc3002000 +#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000 +#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000 +#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000 +#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000 +#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000 +#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000 /* base address of inbound PCIe window */ -#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL +#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL /* System RAM mapped to PCI space */ -#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE -#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE #define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) -#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ +#define CONFIG_SYS_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_UART1_CONSOLE -#undef CFG_EXT_SERIAL_CLOCK +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /*----------------------------------------------------------------------- * DDR SDRAM @@ -120,34 +120,34 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE -#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */ +#define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */ #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0x50) -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0x50) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* I2C RTC */ #define CONFIG_RTC_M41T11 1 -#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */ -#define CFG_I2C_RTC_ADDR 0x68 -#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */ +#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */ /* I2C DTT */ #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ -#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */ +#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ /* * standard dtt sensor configuration - bottom bit will determine local or * remote sensor of the ADM1021, the rest determines index into - * CFG_DTT_ADM1021 array below. + * CONFIG_SYS_DTT_ADM1021 array below. */ #define CONFIG_DTT_SENSORS { 0, 1 } @@ -164,7 +164,7 @@ * - local temp sensor enabled, min set to 0 deg, max set to 85 deg * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg */ -#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } +#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } /*----------------------------------------------------------------------- * Environment @@ -205,21 +205,21 @@ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -237,12 +237,12 @@ #define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ -#undef CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#undef CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */ /* * NETWORK Support (PCI): @@ -254,8 +254,8 @@ * Xilinx System ACE support *----------------------------------------------------------------------*/ #define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */ -#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */ -#define CFG_SYSTEMACE_BASE CFG_ACE_BASE +#define CONFIG_SYS_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */ +#define CONFIG_SYS_SYSTEMACE_BASE CONFIG_SYS_ACE_BASE #define CONFIG_DOS_PARTITION 1 /*----------------------------------------------------------------------- @@ -263,7 +263,7 @@ *----------------------------------------------------------------------*/ /* Memory Bank 0 (Flash) initialization */ -#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ +#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ EBC_BXAP_TWT_ENCODE(7) | \ EBC_BXAP_BCE_DISABLE | \ EBC_BXAP_BCT_2TRANS | \ @@ -276,13 +276,13 @@ EBC_BXAP_SOR_DELAYED | \ EBC_BXAP_BEM_WRITEONLY | \ EBC_BXAP_PEN_DISABLED) -#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | \ +#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ EBC_BXCR_BS_16MB | \ EBC_BXCR_BU_RW | \ EBC_BXCR_BW_16BIT) /* Memory Bank 1 (Xilinx System ACE controller) initialization */ -#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ +#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ EBC_BXAP_TWT_ENCODE(4) | \ EBC_BXAP_BCE_DISABLE | \ EBC_BXAP_BCT_2TRANS | \ @@ -295,7 +295,7 @@ EBC_BXAP_SOR_NONDELAYED | \ EBC_BXAP_BEM_WRITEONLY | \ EBC_BXAP_PEN_DISABLED) -#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \ +#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_ACE_BASE) | \ EBC_BXCR_BS_1MB | \ EBC_BXCR_BU_RW | \ EBC_BXCR_BW_16BIT) @@ -305,7 +305,7 @@ * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 *-------------------------------------------------------------------------*/ -#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK | \ +#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_UNLOCK | \ EBC_CFG_PTD_ENABLE | \ EBC_CFG_RTC_16PERCLK | \ EBC_CFG_ATC_PREVIOUS | \ @@ -319,17 +319,17 @@ /*----------------------------------------------------------------------- * GPIO Setup *----------------------------------------------------------------------*/ -#define CFG_GPIO_PCIE_PRESENT0 17 -#define CFG_GPIO_PCIE_PRESENT1 21 -#define CFG_GPIO_PCIE_PRESENT2 23 -#define CFG_GPIO_RS232_FORCEOFF 30 - -#define CFG_PFC0 (GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) | \ - GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) | \ - GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) | \ - GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)) -#define CFG_GPIO_OR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) -#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) -#define CFG_GPIO_ODR 0 +#define CONFIG_SYS_GPIO_PCIE_PRESENT0 17 +#define CONFIG_SYS_GPIO_PCIE_PRESENT1 21 +#define CONFIG_SYS_GPIO_PCIE_PRESENT2 23 +#define CONFIG_SYS_GPIO_RS232_FORCEOFF 30 + +#define CONFIG_SYS_PFC0 (GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT0) | \ + GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT1) | \ + GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT2) | \ + GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)) +#define CONFIG_SYS_GPIO_OR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) +#define CONFIG_SYS_GPIO_TCR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF) +#define CONFIG_SYS_GPIO_ODR 0 #endif /* __CONFIG_H */ |