diff options
Diffstat (limited to 'include/configs/sc3.h')
| -rw-r--r-- | include/configs/sc3.h | 224 |
1 files changed, 112 insertions, 112 deletions
diff --git a/include/configs/sc3.h b/include/configs/sc3.h index 88a24b87973..44135dfac54 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -128,7 +128,7 @@ #undef CONFIG_BOOTCOMMAND #define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */ -#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ #if 1 /* feel free to disable for development */ #define CONFIG_AUTOBOOT_KEYED /* Enable password protection */ @@ -160,7 +160,7 @@ #undef CONFIG_ISP1161_PRESENT #undef CONFIG_LOADS_ECHO /* no echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_NET_MULTI /* #define CONFIG_EEPRO100_SROM_WRITE */ @@ -205,42 +205,42 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP 1 /* undef to save memory */ -#define CFG_PROMPT "SC3> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ +#define CONFIG_SYS_PROMPT "SC3> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ /* - * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CFG_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. * The Linux BASE_BAUD define should match this configuration. * baseBaud = cpuClock/(uartDivisor*16) - * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. * * Consider the OPB clock! If it get lower the BASE_BAUD must be lower to * (see 405GP datasheet for descritpion) */ -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CFG_BASE_BAUD 921600 /* internal clock */ +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 921600 /* internal clock */ /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} -#define CFG_LOAD_ADDR 0x1000000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * IIC stuff @@ -253,11 +253,11 @@ #define I2C_ACTIVE 0 #define I2C_TRISTATE 0 -#define CFG_I2C_SPEED 100000 /* use the standard 100kHz speed */ -#define CFG_I2C_SLAVE 0x7F /* mask valid bits */ +#define CONFIG_SYS_I2C_SPEED 100000 /* use the standard 100kHz speed */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* mask valid bits */ #define CONFIG_RTC_DS1337 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /*----------------------------------------------------------------------- * PCI stuff @@ -275,14 +275,14 @@ /* If you want to see, whats connected to your PCI bus */ /* #define CONFIG_PCI_SCAN_SHOW */ -#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * External peripheral base address @@ -306,103 +306,103 @@ #define CONFIG_ATAPI #define CONFIG_DOS_PARTITION -#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ #ifndef IDE_USES_ISA_EMULATION /* New and faster access */ -#define CFG_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */ +#define CONFIG_SYS_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */ /* How many IDE busses are available */ -#define CFG_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXBUS 1 /* What IDE ports are available */ -#define CFG_ATA_IDE0_OFFSET 0x000 /* first is available */ -#undef CFG_ATA_IDE1_OFFSET /* second not available */ +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x000 /* first is available */ +#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */ /* access to the data port is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_DATA_OFFSET + 0 */ -#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ /* access to the registers is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_REG_OFFSET + [1..7] */ -#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ /* access to the alternate register is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_ALT_OFFSET + 6 */ -#define CFG_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */ #else /* IDE_USES_ISA_EMULATION */ -#define CFG_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */ +#define CONFIG_SYS_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */ /* How many IDE busses are available */ -#define CFG_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXBUS 1 /* What IDE ports are available */ -#define CFG_ATA_IDE0_OFFSET 0x01F0 /* first is available */ -#undef CFG_ATA_IDE1_OFFSET /* second not available */ +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* first is available */ +#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */ /* access to the data port is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_DATA_OFFSET + 0 */ -#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ /* access to the registers is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_REG_OFFSET + [1..7] */ -#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ /* access to the alternate register is calculated: - CFG_ATA_BASE_ADDR + CFG_ATA_IDE0_OFFSET + CFG_ATA_ALT_OFFSET + 6 */ -#define CFG_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */ + CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */ #endif /* IDE_USES_ISA_EMULATION */ #endif /* -#define CFG_KEY_REG_BASE_ADDR 0xF0100000 -#define CFG_IR_REG_BASE_ADDR 0xF0200000 -#define CFG_FPGA_REG_BASE_ADDR 0xF0300000 +#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 +#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 * - * CFG_FLASH_BASE -> start address of internal flash - * CFG_MONITOR_BASE -> start of u-boot + * CONFIG_SYS_FLASH_BASE -> start address of internal flash + * CONFIG_SYS_MONITOR_BASE -> start of u-boot */ #ifndef __ASSEMBLER__ extern unsigned long offsetOfBigFlash; extern unsigned long offsetOfEnvironment; #endif -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFE00000 -#define CFG_MONITOR_BASE 0xFFFC0000 /* placed last 256k */ -#define CFG_MONITOR_LEN (224 * 1024) /* Reserve 224 KiB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFE00000 +#define CONFIG_SYS_MONITOR_BASE 0xFFFC0000 /* placed last 256k */ +#define CONFIG_SYS_MONITOR_LEN (224 * 1024) /* Reserve 224 KiB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MiB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization ## FIXME: lookup in datasheet */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ -#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */ #define CONFIG_ENV_IS_IN_FLASH 1 #ifdef CONFIG_ENV_IS_IN_FLASH @@ -421,9 +421,9 @@ extern unsigned long offsetOfEnvironment; /* * NAND-FLASH stuff */ -#define CFG_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE 0x77D00000 +#define CONFIG_SYS_NAND_BASE 0x77D00000 #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ @@ -439,55 +439,55 @@ extern unsigned long offsetOfEnvironment; * */ -#define FLASH_BASE0_PRELIM CFG_FLASH_BASE +#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE #define FLASH_BASE1_PRELIM 0 /*----------------------------------------------------------------------- * Some informations about the internal SRAM (OCM=On Chip Memory) * - * CFG_OCM_DATA_ADDR -> location - * CFG_OCM_DATA_SIZE -> size + * CONFIG_SYS_OCM_DATA_ADDR -> location + * CONFIG_SYS_OCM_DATA_SIZE -> size */ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR 0xF8000000 -#define CFG_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM): * - we are using the internal 4k SRAM, so we don't need data cache mapping - * - internal SRAM (OCM=On Chip Memory) is placed to CFG_OCM_DATA_ADDR + * - internal SRAM (OCM=On Chip Memory) is placed to CONFIG_SYS_OCM_DATA_ADDR * - Stackpointer will be located to - * (CFG_INIT_RAM_ADDR&0xFFFF0000) | (CFG_INIT_SP_OFFSET&0x0000FFFF) + * (CONFIG_SYS_INIT_RAM_ADDR&0xFFFF0000) | (CONFIG_SYS_INIT_SP_OFFSET&0x0000FFFF) * in cpu/ppc4xx/start.S */ -#undef CFG_INIT_DCACHE_CS +#undef CONFIG_SYS_INIT_DCACHE_CS /* Where the internal SRAM starts */ -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* Where the internal SRAM ends (only offset) */ -#define CFG_INIT_RAM_END 0x0F00 +#define CONFIG_SYS_INIT_RAM_END 0x0F00 /* - CFG_INIT_RAM_ADDR ------> ------------ lower address + CONFIG_SYS_INIT_RAM_ADDR ------> ------------ lower address | | | ^ | | | | | | Stack | - CFG_GBL_DATA_OFFSET ----> ------------ + CONFIG_SYS_GBL_DATA_OFFSET ----> ------------ | | | 64 Bytes | | | - CFG_INIT_RAM_END ------> ------------ higher address + CONFIG_SYS_INIT_RAM_END ------> ------------ higher address (offset only) */ /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_SIZE 64 -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_SIZE 64 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* Initial value of the stack pointern in internal SRAM */ -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Internal Definitions @@ -504,31 +504,31 @@ extern unsigned long offsetOfEnvironment; /* This chip select accesses the boot device */ /* It depends on boot select switch if this device is 16 or 8 bit */ -#undef CFG_EBC_PB0AP -#undef CFG_EBC_PB0CR +#undef CONFIG_SYS_EBC_PB0AP +#undef CONFIG_SYS_EBC_PB0CR -#undef CFG_EBC_PB1AP -#undef CFG_EBC_PB1CR +#undef CONFIG_SYS_EBC_PB1AP +#undef CONFIG_SYS_EBC_PB1CR -#undef CFG_EBC_PB2AP -#undef CFG_EBC_PB2CR +#undef CONFIG_SYS_EBC_PB2AP +#undef CONFIG_SYS_EBC_PB2CR -#undef CFG_EBC_PB3AP -#undef CFG_EBC_PB3CR +#undef CONFIG_SYS_EBC_PB3AP +#undef CONFIG_SYS_EBC_PB3CR -#undef CFG_EBC_PB4AP -#undef CFG_EBC_PB4CR +#undef CONFIG_SYS_EBC_PB4AP +#undef CONFIG_SYS_EBC_PB4CR -#undef CFG_EBC_PB5AP -#undef CFG_EBC_PB5CR +#undef CONFIG_SYS_EBC_PB5AP +#undef CONFIG_SYS_EBC_PB5CR -#undef CFG_EBC_PB6AP -#undef CFG_EBC_PB6CR +#undef CONFIG_SYS_EBC_PB6AP +#undef CONFIG_SYS_EBC_PB6CR -#undef CFG_EBC_PB7AP -#undef CFG_EBC_PB7CR +#undef CONFIG_SYS_EBC_PB7AP +#undef CONFIG_SYS_EBC_PB7CR -#define CFG_EBC_CFG 0xb84ef000 +#define CONFIG_SYS_EBC_CFG 0xb84ef000 #define CONFIG_SDRAM_BANK0 /* use the standard SDRAM initialization */ #undef CONFIG_SPD_EEPROM @@ -543,15 +543,15 @@ extern unsigned long offsetOfEnvironment; * External peripheral base address ***********************************************************************/ -#define CFG_ISA_MEM_BASE_ADDRESS 0x78000000 +#define CONFIG_SYS_ISA_MEM_BASE_ADDRESS 0x78000000 /* Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu. Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen auf ISA- und PCI-Zyklen) */ -#define CFG_ISA_IO_BASE_ADDRESS 0xE8000000 -/*#define CFG_ISA_IO_BASE_ADDRESS 0x79000000 */ +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000 +/*#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0x79000000 */ /************************************************************ * Video support |