diff options
Diffstat (limited to 'include/configs/utx8245.h')
| -rw-r--r-- | include/configs/utx8245.h | 346 |
1 files changed, 346 insertions, 0 deletions
diff --git a/include/configs/utx8245.h b/include/configs/utx8245.h new file mode 100644 index 00000000000..5aec47af6b5 --- /dev/null +++ b/include/configs/utx8245.h @@ -0,0 +1,346 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2002 + * Gregory E. Allen, gallen@arlut.utexas.edu + * Matthew E. Karger, karger@arlut.utexas.edu + * Applied Research Laboratories, The University of Texas at Austin + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * + * Configuration settings for the utx8245 board. + * + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC824X 1 +#define CONFIG_MPC8245 1 +#define CONFIG_UTX8245 1 +#define DEBUG 1 + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 57600 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_BOOTDELAY 5 +#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n" +#define CONFIG_BOOTCOMMAND "bootm FF920000 FF800000" /* autoboot command */ +#define CONFIG_BOOTARGS "root=/dev/ram console=ttyS0,57600" /* RAMdisk */ +#define CONFIG_ETHADDR 41:52:4c:61:00:01 /* MAC address */ +#define CONFIG_SERVERIP 10.8.17.105 +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_COMMANDS (CFG_CMD_DFL | CFG_CMD_BDI | CFG_CMD_PCI \ + | CFG_CMD_FLASH | CFG_CMD_MEMORY \ + | CFG_CMD_ENV | CFG_CMD_CONSOLE \ + | CFG_CMD_LOADS | CFG_CMD_LOADB \ + | CFG_CMD_IMI | CFG_CMD_CACHE \ + | CFG_CMD_RUN | CFG_CMD_ECHO \ + | CFG_CMD_REGINFO | CFG_CMD_NET\ + | CFG_CMD_DHCP) + +/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) + */ +#include <cmd_confdefs.h> + + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) + +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* Default load address */ + + +/*----------------------------------------------------------------------- + * PCI configuration + *----------------------------------------------------------------------- + */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_NET_MULTI +#define CONFIG_EEPRO100 + +#define PCI_ENET0_IOADDR 0x80000000 +#define PCI_ENET0_MEMADDR 0x80000000 +#define PCI_FIREWIRE_IOADDR 0x81000000 +#define PCI_FIREWIRE_MEMADDR 0x81000000 + + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_MAX_RAM_SIZE 0x10000000 /* amount of SDRAM */ + + +/* even though FLASHP_BASE is FF800000, with 2MB on RCS0, the + * reset vector is actually located at FF800100, but the 8245 + * takes care of us. + */ +#define CFG_RESET_ADDRESS 0xFFF00100 + +#define CFG_EUMB_ADDR 0xFC000000 + +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/*#define CFG_DRAM_TEST 1 */ +#define CFG_MEMTEST_START 0x00003000 /* memtest works on 0...256 MB */ +#define CFG_MEMTEST_END 0x0ff8ffa8 /* in SDRAM, skips exception */ + /* vectors and U-Boot */ + + +/*-------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + *------------------------------------------------------------------*/ +#define CFG_GBL_DATA_SIZE 128 /* Size in bytes reserved for */ + /* initial data */ +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x1000 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/*-------------------------------------------------------------------- + * NS16550 Configuration + *------------------------------------------------------------------*/ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL + +#define CFG_NS16550_REG_SIZE 1 + +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_NS16550_COM1 (CFG_EUMB_ADDR + 0x4500) +#define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4600) + +/*-------------------------------------------------------------------- + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + * For the detail description refer to the MPC8240 user's manual. + *------------------------------------------------------------------*/ + +#define CONFIG_SYS_CLK_FREQ 33000000 +#define CFG_HZ 1000 + +#define CFG_ETH_DEV_FN 0x7800 +#define CFG_ETH_IOBASE 0x00104000 + + +/*-------------------------------------------------------------------- + * Memory Control Configuration Register values + * - see sec. 4.12 of MPC8245 UM + *------------------------------------------------------------------*/ + +/* MCCR1 */ +#define CFG_ROMNAL 0 +#define CFG_ROMFAL 2 /* (tacc=70ns)*mem_freq - 2 */ +#define CFG_BANK0_ROW 2 /* SDRAM bank 7-0 row address */ +#define CFG_BANK1_ROW 2 /* bit count */ +#define CFG_BANK2_ROW 0 +#define CFG_BANK3_ROW 0 +#define CFG_BANK4_ROW 0 +#define CFG_BANK5_ROW 0 +#define CFG_BANK6_ROW 0 +#define CFG_BANK7_ROW 0 + +/* MCCR2, refresh interval clock cycles */ +#define CFG_REFINT 480 /* 33 MHz SDRAM clock was 480 */ + +/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4 */ +#define CFG_BSTOPRE 1023 /* burst to precharge[0..9], */ + /* sets open page interval */ + +/* MCCR3 */ +#define CFG_REFREC 5 /* Refresh to activate interval, trc */ + +/* MCCR4 */ +#define CFG_PRETOACT 2 /* trp */ +#define CFG_ACTTOPRE 7 /* trcd + (burst length - 1) + tdrl */ +#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ +#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type, sequential */ +#define CFG_ACTORW 2 /* trcd min */ +#define CFG_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */ +#define CFG_REGISTERD_TYPE_BUFFER 1 +#define CFG_EXTROM 1 +#define CFG_REGDIMM 0 + +/* calculate according to formula in sec. 6-22 of 8245 UM */ +#define CFG_PGMAX 50 /* how long the 8245 retains the */ + /* currently accessed page in memory */ + /* was 45 */ + +#define CFG_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note */ + /* bottom 3 bits MUST be 0 */ + +#define CFG_DLL_MAX_DELAY 0x04 +#define CFG_DLL_EXTEND 0x80 +#define CFG_PCI_HOLD_DEL 0x20 + + +/* Memory bank settings. + * Only bits 20-29 are actually used from these values to set the + * start/end addresses. The upper two bits will always be 0, and the lower + * 20 bits will be 0x00000 for a start address, or 0xfffff for an end + * address. Refer to the MPC8245 user manual. + */ + +#define CFG_BANK0_START 0x00000000 +#define CFG_BANK0_END (CFG_MAX_RAM_SIZE/2 - 1) +#define CFG_BANK0_ENABLE 1 +#define CFG_BANK1_START CFG_MAX_RAM_SIZE/2 +#define CFG_BANK1_END (CFG_MAX_RAM_SIZE - 1) +#define CFG_BANK1_ENABLE 1 +#define CFG_BANK2_START 0x3ff00000 /* not available in this design */ +#define CFG_BANK2_END 0x3fffffff +#define CFG_BANK2_ENABLE 0 +#define CFG_BANK3_START 0x3ff00000 +#define CFG_BANK3_END 0x3fffffff +#define CFG_BANK3_ENABLE 0 +#define CFG_BANK4_START 0x3ff00000 +#define CFG_BANK4_END 0x3fffffff +#define CFG_BANK4_ENABLE 0 +#define CFG_BANK5_START 0x3ff00000 +#define CFG_BANK5_END 0x3fffffff +#define CFG_BANK5_ENABLE 0 +#define CFG_BANK6_START 0x3ff00000 +#define CFG_BANK6_END 0x3fffffff +#define CFG_BANK6_ENABLE 0 +#define CFG_BANK7_START 0x3ff00000 +#define CFG_BANK7_END 0x3fffffff +#define CFG_BANK7_ENABLE 0 + +/*-------------------------------------------------------------------- + * 4.4 - Output Driver Control Register + *------------------------------------------------------------------*/ +#define CFG_ODCR 0xe5 + +/*-------------------------------------------------------------------- + * 4.8 - Error Handling Registers + *------------------------------------------------------------------*/ +#define CFG_ERRENR1 0x11 /* enable SDRAM refresh overflow error */ + +/* SDRAM 0-256 MB */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* stack in dcache */ +#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) + +/* PCI memory */ +#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +/* Flash, config addrs, etc. */ +#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization (AMD AM29LV116D) + */ +#define CFG_FLASH_BASE 0xFF800000 + +#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 35 /* Max number of sectors in one bank */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + + /* Warning: environment is not EMBEDDED in the U-Boot code. + * It's stored in flash separately. + */ +#define CFG_ENV_IS_IN_FLASH 1 + +#define CFG_ENV_ADDR 0xFF9FA000 /* flash sector SA33 */ +#define CFG_ENV_SIZE 0x2000 /* Size of the Environment */ +#define CFG_ENV_OFFSET 0 /* starting right at the beginning */ +#define CFG_ENV_SECT_SIZE 0x2000 /* Size of the Environment Sector */ + + +#if CFG_MONITOR_BASE >= CFG_FLASH_BASE +#undef CFG_RAMBOOT +#else +#define CFG_RAMBOOT +#endif + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +#endif /* __CONFIG_H */ |