diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/FADS823.h | 470 | ||||
| -rw-r--r-- | include/configs/GEN860T.h | 717 | ||||
| -rw-r--r-- | include/configs/NETVIA.h | 348 | ||||
| -rw-r--r-- | include/configs/RPXClassic.h | 439 | ||||
| -rw-r--r-- | include/configs/RPXlite.h | 392 | ||||
| -rw-r--r-- | include/configs/RPXsuper.h | 505 | ||||
| -rw-r--r-- | include/configs/ep8260.h | 689 |
7 files changed, 3560 insertions, 0 deletions
diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h new file mode 100644 index 00000000000..58d33c77e56 --- /dev/null +++ b/include/configs/FADS823.h @@ -0,0 +1,470 @@ + /* + * A collection of structures, addresses, and values associated with + * the Motorola 860T FADS board. Copied from the MBX stuff. + * Magnus Damm added defines for 8xxrom and extended bd_info. + * Helmut Buchsbaum added bitvalues for BCSRx + * + * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) + */ + +/* + * 1999-nov-26: The FADS is using the following physical memorymap: + * + * ff020000 -> ff02ffff : pcmcia io remapping + * ff010000 -> ff01ffff : BCSR connected to CS1, setup by U-Boot + * ff000000 -> ff00ffff : IMAP internal in the cpu + * e0000000 -> f3ffffff : pcmcia memory remapping by m8xx_pcmcia + * fe000000 -> fe1fffff : flash connected to CS0, setup by U-Boot + * 00000000 -> nnnnnnnn : sdram/dram setup by U-Boot +*/ + +#define CFG_PCMCIA_IO_ADDR 0xff020000 +#define CFG_PCMCIA_IO_SIZE 0x10000 +#define CFG_PCMCIA_MEM_ADDR 0xe0000000 +#define CFG_PCMCIA_MEM_SIZE 0x10000 +#define CFG_IMMR 0xFF000000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x02800000 +#define BCSR_ADDR ((uint) 0xff010000) +#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */ +#define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */ + +#define CONFIG_VIDEO 1 /* To enable video controller support */ +#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/*Now included by CFG_CMD_PCMCIA */ +/*#define CONFIG_PCMCIA 1 / * To enable PCMCIA support */ + +/* Video related */ + +#define CONFIG_VIDEO_LOGO 1 /* Show the logo */ +#define CONFIG_VIDEO_ENCODER_AD7176 1 /* Enable this encoder */ +#define CONFIG_VIDEO_ENCODER_AD7176_ADDR 0x54 /* Default on fads */ +#define CONFIG_VIDEO_SIZE (2*1024*1024) +/* #define CONFIG_VIDEO_ADDR (gd->bd->bi_memsize - CONFIG_VIDEO_SIZE) Frame buffer address */ + +/* Wireless 56Khz 4PPM keyboard on SMCx */ + +/*#define CONFIG_WL_4PPM_KEYBOARD 1 */ +#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 /* SMC to use (0 indexed) */ + +/* + * High Level Configuration Options + * (easy to change) + */ +#include <mpc8xx_irq.h> + +#define CONFIG_MPC823 1 +#define CONFIG_MPC823FADS 1 +#define CONFIG_FADS 1 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 + +/* Set the CPU speed to 50Mhz on the FADS */ + +#if 0 +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 5000000 /* 5 MHz in */ +#else +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 5000000 /* 5 MHz in */ +#define CFG_PLPRCR_MF (MPC8XX_FACT-1) << 20 /* From 0 to 4095 */ +#endif +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#if 1 +#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */ +#define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */ +#define CONFIG_BOOTARGS "" +#define CONFIG_BOOTCOMMAND \ +"bootp ;" \ +"setenv bootargs console=tty0 console=ttyS0 " \ +"root=/dev/nfs nfsroot=$(serverip):$(rootpath) " \ +"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):eth0:off ;" \ +"bootm" +#else +#define CONFIG_BOOTDELAY 0 /* autoboot disabled */ +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_ALL + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT ":>" /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x01000000 /* 0 ... 16 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR_SIZE ((uint)(64 * 1024)) + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Also NOTE that it doesn't mean SDRAM - it means MEMORY. + */ +#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ +#if 0 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer * + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CFG_PLPRCR_MF) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + + /*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* Because of the way the 860 starts up and assigns CS0 the +* entire address space, we have to set the memory controller +* differently. Normally, you write the option register +* first, and then enable the chip select by writing the +* base register. For CS0, you must write the base register +* first, followed by the option register. +*/ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ +/* the other CS:s are determined by looking at parameters in BCSRx */ + +#define BCSR_SIZE ((uint)(64 * 1024)) + +#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */ + +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */ + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) + +/* BCSRx - Board Control and Status Registers */ +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */ +#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V ) + + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +#define CFG_MAMR 0x13a01114 +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* values according to the manual */ + +#define BCSR0 ((uint) (BCSR_ADDR + 00)) +#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) +#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) +#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) +#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) + +/* FADS bitvalues by Helmut Buchsbaum + * see MPC8xxADS User's Manual for a proper description + * of the following structures + */ + +#define BCSR0_ERB ((uint)0x80000000) +#define BCSR0_IP ((uint)0x40000000) +#define BCSR0_BDIS ((uint)0x10000000) +#define BCSR0_BPS_MASK ((uint)0x0C000000) +#define BCSR0_ISB_MASK ((uint)0x01800000) +#define BCSR0_DBGC_MASK ((uint)0x00600000) +#define BCSR0_DBPC_MASK ((uint)0x00180000) +#define BCSR0_EBDF_MASK ((uint)0x00060000) + +#define BCSR1_FLASH_EN ((uint)0x80000000) +#define BCSR1_DRAM_EN ((uint)0x40000000) +#define BCSR1_ETHEN ((uint)0x20000000) +#define BCSR1_IRDEN ((uint)0x10000000) +#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) +#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) +#define BCSR1_BCSR_EN ((uint)0x02000000) +#define BCSR1_RS232EN_1 ((uint)0x01000000) +#define BCSR1_PCCEN ((uint)0x00800000) +#define BCSR1_PCCVCC0 ((uint)0x00400000) +#define BCSR1_PCCVPP_MASK ((uint)0x00300000) +#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) +#define BCSR1_RS232EN_2 ((uint)0x00040000) +#define BCSR1_SDRAM_EN ((uint)0x00020000) +#define BCSR1_PCCVCC1 ((uint)0x00010000) + +#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) +#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) +#define BCSR2_DRAM_PD_SHIFT (23) +#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) +#define BCSR2_DBREVNR_MASK ((uint)0x00030000) + +#define BCSR3_DBID_MASK ((ushort)0x3800) +#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) +#define BCSR3_BREVNR0 ((ushort)0x0080) +#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) +#define BCSR3_BREVN1 ((ushort)0x0008) +#define BCSR3_BREVN2_MASK ((ushort)0x0003) + +#define BCSR4_ETHLOOP ((uint)0x80000000) +#define BCSR4_TFPLDL ((uint)0x40000000) +#define BCSR4_TPSQEL ((uint)0x20000000) +#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) +#ifdef CONFIG_MPC823 +#define BCSR4_USB_EN ((uint)0x08000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860SAR +#define BCSR4_UTOPIA_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860SAR */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETH_EN ((uint)0x08000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_USB_SPEED ((uint)0x04000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHCFG0 ((uint)0x04000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VCCO ((uint)0x02000000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHFDE ((uint)0x02000000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VIDEO_ON ((uint)0x00800000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC823 +#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHCFG1 ((uint)0x00400000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_VIDEO_RST ((uint)0x00200000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC860T +#define BCSR4_FETHRST ((uint)0x00200000) +#endif /* CONFIG_MPC860T */ +#ifdef CONFIG_MPC823 +#define BCSR4_MODEM_EN ((uint)0x00100000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC823 +#define BCSR4_DATA_VOICE ((uint)0x00080000) +#endif /* CONFIG_MPC823 */ +#ifdef CONFIG_MPC850 +#define BCSR4_DATA_VOICE ((uint)0x00080000) +#endif /* CONFIG_MPC850 */ + +#define CONFIG_DRAM_50MHZ 1 +#define CONFIG_SDRAM_50MHZ + +#ifdef CONFIG_MPC860T + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ + +#endif /* CONFIG_MPC860T */ + +/* We don't use the 8259. +*/ +#define NR_8259_INTS 0 + +/* Machine type +*/ +#define _MACH_8xx (_MACH_fads) + +/* + * MPC8xx CPM Options + */ +#define CONFIG_SCC_ENET 1 +#define CONFIG_SCC2_ENET 1 +#undef CONFIG_FEC_ENET +#undef CONFIG_CPM_IIC +#undef CONFIG_UCODE_PATCH + +#define CONFIG_DISK_SPINUP_TIME 1000000 + +/* PCMCIA configuration */ + +#define PCMCIA_MAX_SLOTS 1 + +#ifdef CONFIG_MPC860 +#define PCMCIA_SLOT_A 1 +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h new file mode 100644 index 00000000000..29e4807ea2a --- /dev/null +++ b/include/configs/GEN860T.h @@ -0,0 +1,717 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * Keith Outwater, keith_outwater@mvis.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config_GEN860T.h - board specific configuration options + */ + +#ifndef __CONFIG_GEN860T_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_MPC860 +#define CONFIG_GEN860T + +/* + * Identify the board + */ +#define CONFIG_IDENT_STRING " GEN860T" + +/* + * Don't depend on the RTC clock to determine clock frequency - + * the 860's internal rtc uses a 32.768 KHz clock which is + * generated by the DS1337 - and the DS1337 clock can be turned off. + */ +#define CONFIG_8xx_GCLK_FREQ 66600000 + +/* + * The RS-232 console port is on SMC1 + */ +#define CONFIG_8xx_CONS_SMC1 +#define CONFIG_BAUDRATE 38400 + +/* + * Set allowable console baud rates + */ +#define CFG_BAUDRATE_TABLE { 9600, \ + 19200, \ + 38400, \ + 57600, \ + 115200, \ + } + +/* + * Print console information + */ +#undef CFG_CONSOLE_INFO_QUIET + +/* + * Set the autoboot delay in seconds. A delay of -1 disables autoboot + */ +#define CONFIG_BOOTDELAY 5 + +/* + * Pass the clock frequency to the Linux kernel in units of MHz + */ +#define CONFIG_CLOCKS_IN_MHZ + +#define CONFIG_PREBOOT \ + "echo;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +/* + * Turn off echo for serial download by default. Allow baud rate to be changed + * for downloads + */ +#undef CONFIG_LOADS_ECHO +#define CFG_LOADS_BAUD_CHANGE + +/* + * Set default load address for tftp network downloads + */ +#define CFG_TFTP_LOADADDR 0x01000000 + +/* + * Turn off the watchdog timer + */ +#undef CONFIG_WATCHDOG + +/* + * Do not reboot if a panic occurs + */ +#define CONFIG_PANIC_HANG + +/* + * Enable the status LED + */ +#define CONFIG_STATUS_LED + +/* + * Reset address. We pick an address such that when an instruction + * is executed at that address, a machine check exception occurs + */ +#define CFG_RESET_ADDRESS ((ulong) -1) + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE \ + ) + +/* + * The GEN860T network interface uses the on-chip 10/100 FEC with + * an Intel LXT971A PHY connected to the 860T's MII. The PHY's + * MII address is hardwired on the board to zero. + */ +#define CONFIG_FEC_ENET +#define CFG_DISCOVER_PHY +#define CONFIG_MII +#define CONFIG_PHY_ADDR 0 + +/* + * Set default IP stuff just to get bootstrap entries into the + * environment so that we can autoscript the full default environment. + */ +#define CONFIG_ETHADDR 9a:52:63:15:85:25 +#define CONFIG_SERVERIP 10.0.4.200 +#define CONFIG_IPADDR 10.0.4.111 + +/* + * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to + * the MPC860T I2C interface. + */ +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */ +#define CFG_ENV_EEPROM_SIZE (32 * 1024) + +#undef CONFIG_HARD_I2C +#define CONFIG_SOFT_I2C + +/* + * Configure software I2C support (taken from IP860 BSP). + * The I2C bus is connected to the GEN860T's 'dedicated' I2C + * pins, i.e. PB26 and PB27 + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CFG_I2C_SPEED 100000 /* clock speed in Hz */ +#define CFG_I2C_SLAVE 0xFE /* I2C slave address */ + +/* + * Allow environment overwrites by anyone + */ +#define CONFIG_ENV_OVERWRITE + +/* + * The MPC860's internal RTC is horribly broken in rev D masks. Three + * internal MPC860T circuit nodes were inadvertently left floating; this + * causes KAPWR current in power down mode to be three orders of magnitude + * higher than specified in the datasheet (from 10 uA to 10 mA). No + * reasonable battery can keep that kind RTC running during powerdown for any + * length of time, so we use an external RTC on the I2C bus instead. + */ +#undef CONFIG_RTC_MPC8xx +#define CONFIG_RTC_DS1337 +#define CFG_I2C_RTC_ADDR 0x68 + +/* + * Allow partial commands to be matched to uniqueness. + */ +#define CFG_MATCH_PARTIAL_CMD + +/* + * List of available monitor commands. Use the system default list + * plus add some of the "non-standard" commands back in. + * See ./cmd_confdefs.h + */ +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_DOC | \ + CFG_CMD_EEPROM | \ + CFG_CMD_REGINFO | \ + CFG_CMD_IMMAP | \ + CFG_CMD_ELF | \ + CFG_CMD_DATE | \ + CFG_CMD_DATE | \ + CFG_CMD_FPGA | \ + CFG_CMD_MII | \ + CFG_CMD_BEDBUG \ + ) + +/* + * There is no IDE/PCMCIA hardware support on the board. + */ +#undef CONFIG_IDE_PCMCIA +#undef CONFIG_IDE_LED +#undef CONFIG_IDE_RESET + +/* + * Enable the call to misc_init_r() for miscellaneous platform + * dependent initialization. + */ +#define CONFIG_MISC_INIT_R + +/* + * Enable call to last_stage_init() so we can twiddle some LEDS :) + */ +#define CONFIG_LAST_STAGE_INIT + +/* + * Virtex2 FPGA configuration support + */ +#define CONFIG_FPGA_COUNT 1 +#define CONFIG_FPGA CFG_XILINX_VIRTEX2 +#define CFG_FPGA_PROG_FEEDBACK + + +/************************************************************************ + * This must be included AFTER the definition of any CONFIG_COMMANDS + */ +#include <cmd_confdefs.h> + +/* + * Verbose help from command monitor. + */ +#define CFG_LONGHELP +#define CFG_PROMPT "gen860t> " + +/* + * Use the "hush" command parser + */ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " + +/* + * Set buffer size for console I/O + */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 +#else +#define CFG_CBSIZE 256 +#endif + +/* + * Print buffer size + */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) + +/* + * Maximum number of arguments that a command can accept + */ +#define CFG_MAXARGS 16 + +/* + * Boot argument buffer size + */ +#define CFG_BARGSIZE CFG_CBSIZE + +/* + * Default memory test range + */ +#define CFG_MEMTEST_START 0x0100000 +#define CFG_MEMTEST_END (CFG_MEMTEST_START + (128 * 1024)) + +/* + * Select the more full-featured memory test + */ +#define CFG_ALT_MEMTEST + +/* + * Default load address + */ +#define CFG_LOAD_ADDR 0x01000000 + +/* + * Set decrementer frequency (1 ms ticks) + */ +#define CFG_HZ 1000 + +/* + * Device memory map (after SDRAM remap to 0x0): + * + * CS Device Base Addr Size + * ---------------------------------------------------- + * CS0* Flash 0x40000000 64 M + * CS1* SDRAM 0x00000000 16 M + * CS2* Disk-On-Chip 0x50000000 32 K + * CS3* FPGA 0x60000000 64 M + * CS4* SelectMap 0x70000000 32 K + * CS5* Mil-Std 1553 I/F 0x80000000 32 K + * CS6* Unused + * CS7* Unused + * IMMR 860T Registers 0xfff00000 + */ + +/* + * Base addresses and block sizes + */ +#define CFG_IMMR 0xFF000000 + +#define SDRAM_BASE 0x00000000 +#define SDRAM_SIZE (64 * 1024 * 1024) + +#define FLASH_BASE 0x40000000 +#define FLASH_SIZE (16 * 1024 * 1024) + +#define DOC_BASE 0x50000000 +#define DOC_SIZE (32 * 1024) + +#define FPGA_BASE 0x60000000 +#define FPGA_SIZE (64 * 1024 * 1024) + +#define SELECTMAP_BASE 0x70000000 +#define SELECTMAP_SIZE (32 * 1024) + +#define M1553_BASE 0x80000000 +#define M1553_SIZE (64 * 1024) + +/* + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE SDRAM_BASE + +/* + * FLASH organization + */ +#define CFG_FLASH_BASE FLASH_BASE +#define CFG_FLASH_SIZE FLASH_SIZE +#define CFG_FLASH_SECT_SIZE (128 * 1024) +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 128 + +/* + * The timeout values are for an entire chip and are in milliseconds. + * Yes I know that the write timeout is huge. Accroding to the + * datasheet a single byte takes 630 uS (round to 1 ms) max at worst + * case VCC and temp after 100K programming cycles. It works out + * to 280 minutes (might as well be forever). + */ +#define CFG_FLASH_ERASE_TOUT (CFG_MAX_FLASH_SECT * 5000) +#define CFG_FLASH_WRITE_TOUT (CFG_MAX_FLASH_SECT * 128 * 1024 * 1) + +/* + * Allow direct writes to FLASH from tftp transfers (** dangerous **) + */ +#define CFG_DIRECT_FLASH_TFTP + +/* + * Reserve memory for U-Boot. + */ +#define CFG_MAX_U_BOOT_SECT 3 + +#if defined(DEBUG) +#define CFG_MONITOR_LEN (512 * 1024) +#else +#define CFG_MONITOR_LEN (256 * 1024) +#endif + +#define CFG_MONITOR_BASE CFG_FLASH_BASE + +/* + * Select environment placement. NOTE that u-boot.lds must + * be edited if this is changed! + */ +#undef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_IS_IN_EEPROM + +#if defined(CFG_ENV_IS_IN_EEPROM) +#define CFG_ENV_SIZE (2 * 1024) +#define CFG_ENV_OFFSET (CFG_ENV_EEPROM_SIZE - (8 * 1024)) +#else +#define CFG_ENV_SIZE (4 * 1024) +#define CFG_ENV_OFFSET (CFG_MAX_U_BOOT_SECT * CFG_FLASH_SECT_SIZE) +#endif + +/* + * Reserve memory for malloc() + */ +#define CFG_MALLOC_LEN (128 * 1024) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 * 1024 * 1024) + +/* + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of above value */ +#endif + +/*------------------------------------------------------------------------ + * SYPCR - System Protection Control UM 11-9 + * ----------------------------------------------------------------------- + * SYPCR can only be written once after reset! + * + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR ( SYPCR_SWTC | \ + SYPCR_BMT | \ + SYPCR_BME | \ + SYPCR_SWF | \ + SYPCR_SWE | \ + SYPCR_SWRI | \ + SYPCR_SWP \ + ) +#else +#define CFG_SYPCR ( SYPCR_SWTC | \ + SYPCR_BMT | \ + SYPCR_BME | \ + SYPCR_SWF | \ + SYPCR_SWP \ + ) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration UM 11-6 + *----------------------------------------------------------------------- + * Set debug pin mux, enable SPKROUT and GPLB5*. + */ +#define CFG_SIUMCR ( SIUMCR_DBGC11 | \ + SIUMCR_DBPC11 | \ + SIUMCR_MLRC11 | \ + SIUMCR_GB5E \ + ) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control UM 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freeze enabled + */ +#define CFG_TBSCR ( TBSCR_REFA | \ + TBSCR_REFB | \ + TBSCR_TBF \ + ) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register UM 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC ( RTCSC_SEC | \ + RTCSC_ALR | \ + RTCSC_RTF | \ + RTCSC_RTE \ + ) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control UM 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR ( PISCR_PS | \ + PISCR_PITF \ + ) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register UM 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit. Set MF for 1:2:1 mode. + */ +#define CFG_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \ + PLPRCR_SPLSS | \ + PLPRCR_TEXPS | \ + PLPRCR_TMIST \ + ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register UM 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 + +#define CFG_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \ + SCCR_COM00 | /* full strength CLKOUT */ \ + SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \ + SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \ + SCCR_DFNL000 | \ + SCCR_DFNH000 \ + ) + +/*----------------------------------------------------------------------- + * DER - Debug Enable Register UM 37-46 + *----------------------------------------------------------------------- + * Mask all events that can cause entry into debug mode + */ +#define CFG_DER 0 + +/* + * Initialize Memory Controller: + * + * BR0 and OR0 (FLASH memory) + */ +#define FLASH_BASE0_PRELIM FLASH_BASE + +/* + * Flash address mask + */ +#define CFG_PRELIM_OR_AM 0xfe000000 + +/* + * FLASH timing: + * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 + */ +#define CFG_OR_TIMING_FLASH ( OR_CSNT_SAM | \ + OR_ACS_DIV2 | \ + OR_BI | \ + OR_SCY_2_CLK | \ + OR_TRLX | \ + OR_EHTR \ + ) + +#define CFG_OR0_PRELIM ( CFG_PRELIM_OR_AM | \ + CFG_OR_TIMING_FLASH \ + ) + +#define CFG_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \ + BR_MS_GPCM | \ + BR_PS_8 | \ + BR_V \ + ) + +/* + * SDRAM configuration + */ +#define CFG_OR1_AM 0xfc000000 +#define CFG_OR1 ( (CFG_OR1_AM & OR_AM_MSK) | \ + OR_CSNT_SAM \ + ) + +#define CFG_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \ + BR_MS_UPMA | \ + BR_PS_32 | \ + BR_V \ + ) + +/* + * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank + * of 256 MBit SDRAM + */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 + +/* + * Periodic timer for refresh @ 33 MHz system clock + */ +#define CFG_MAMR_PTA 64 + +/* + * MAMR settings for SDRAM + */ +#define CFG_MAMR_8COL ( (CFG_MAMR_PTA << MAMR_PTA_SHIFT) | \ + MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | \ + MAMR_DSA_1_CYCL | \ + MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | \ + MAMR_WLFA_1X | \ + MAMR_TLFA_4X \ + ) + +/* + * CS2* configuration for Disk On Chip: + * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1, + * no burst. + */ +#define CFG_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ + OR_CSNT_SAM | \ + OR_ACS_DIV2 | \ + OR_BI | \ + OR_SCY_2_CLK | \ + OR_TRLX | \ + OR_EHTR \ + ) + +#define CFG_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \ + BR_PS_8 | \ + BR_MS_GPCM | \ + BR_V \ + ) + +/* + * CS3* configuration for FPGA: + * 33 MHz bus with SCY=15, no burst. + * The FPGA uses TA and TEA to terminate bus cycles, but we + * clear SETA and set the cycle length to a large number so that + * the cycle will still complete even if there is a configuration + * error that prevents TA from asserting on FPGA accesss. + */ +#define CFG_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \ + OR_SCY_15_CLK | \ + OR_BI \ + ) + +#define CFG_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \ + BR_PS_32 | \ + BR_MS_GPCM | \ + BR_V \ + ) +/* + * CS4* configuration for FPGA SelectMap configuration interface. + * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge + * of GCLK1_50 + */ +#define CFG_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ + OR_G5LS | \ + OR_BI \ + ) + +#define CFG_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \ + BR_PS_8 | \ + BR_MS_UPMB | \ + BR_V \ + ) + +/* + * CS5* configuration for Mil-Std 1553 databus interface. + * 33 MHz bus, GPCM, no burst. + * The 1553 interface uses TA and TEA to terminate bus cycles, + * but we clear SETA and set the cycle length to a large number so that + * the cycle will still complete even if there is a configuration + * error that prevents TA from asserting on FPGA accesss. + */ +#define CFG_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \ + OR_SCY_15_CLK | \ + OR_EHTR | \ + OR_TRLX | \ + OR_CSNT_SAM | \ + OR_BI \ + ) + +#define CFG_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \ + BR_PS_16 | \ + BR_MS_GPCM | \ + BR_V \ + ) + +/* + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Disk On Chip (millenium) configuration + */ +#define CFG_MAX_DOC_DEVICE 1 +#undef CFG_DOC_SUPPORT_2000 +#define CFG_DOC_SUPPORT_MILLENNIUM +#undef CFG_DOC_PASSIVE_PROBE + +/* + * FEC interrupt assignment + */ +#define FEC_INTERRUPT SIU_LEVEL1 + +/* + * Sanity checks + */ +#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) +#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured +#endif + +#endif /* __CONFIG_GEN860T_H */ + +/* vim: set ts=4 tw=78 ai shiftwidth=4: */ diff --git a/include/configs/NETVIA.h b/include/configs/NETVIA.h new file mode 100644 index 00000000000..78853250a03 --- /dev/null +++ b/include/configs/NETVIA.h @@ -0,0 +1,348 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Pantelis Antoniou, Intracom S.A., panto@intracom.gr + * U-Boot port on NetVia board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ +#define CONFIG_NETVIA 1 /* ...on a NetVia board */ +#undef CONFIG_NETVIA_PLL_CLOCK /* PLL or fixed crystal clock */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +#ifdef CONFIG_NETVIA_PLL_CLOCK +/* XXX make sure that you calculate these two correctly */ +#define CFG_GCLK_MF 1350 +#define CONFIG_8xx_GCLK_FREQ 44236800 +#else +#define CFG_GCLK_MF 1 +#define CONFIG_8xx_GCLK_FREQ 50000000 +#endif + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#undef CONFIG_MAC_PARTITION +#undef CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP ) + +#define CONFIG_BOARD_PRE_INIT +#define CONFIG_MISC_INIT_R + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0300000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x10000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + */ + +#define CFG_PLPRCR ( ((CFG_GCLK_MF-1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR1/2 and OR1/2 (4MByte Flash Bank x 2) + * + */ +#define FLASH0_SIZE 0x00400000 /* 4MByte */ +#define FLASH0_BASE 0xF0000000 + +#define CFG_OR1_PRELIM ((0xFFFFFFFFLU & ~(FLASH0_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) +#define CFG_BR1_PRELIM ((FLASH0_BASE & BR_BA_MSK) | BR_PS_32 | BR_V) + +#define FLASH1_SIZE 0x00400000 +#define FLASH1_BASE 0xF0400000 + +#define CFG_OR2_PRELIM ((0xFFFFFFFFLU & ~(FLASH1_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) +#define CFG_BR2_PRELIM ((FLASH1_BASE & BR_BA_MSK) | BR_PS_32 | BR_V) + +/* + * BR3 and OR3 (SDRAM) + * + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) + +#define CFG_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CFG_OR_TIMING_SDRAM) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_PS_32 | BR_V) + +/* + * BR6 (External register) + * 16 bit port size - leds are at high 8 bits + */ +#define EXTREG_BASE 0x30000000 /* external register */ +#define EXTREG_SIZE 0x00010000 /* max 64K */ + +#define CFG_OR6_PRELIM ((0xFFFFFFFFLU & ~(EXTREG_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_15_CLK | OR_TRLX) +#define CFG_BR6_PRELIM ((EXTREG_BASE & BR_BA_MSK) | BR_PS_32 | BR_V) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 208 + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* Ethernet at SCC2 */ +#define CONFIG_SCC2_ENET + +#endif /* __CONFIG_H */ diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h new file mode 100644 index 00000000000..d742a25dcbc --- /dev/null +++ b/include/configs/RPXClassic.h @@ -0,0 +1,439 @@ +/* + * (C) Copyright 2000, 2001, 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr + * U-Boot port on RPXlite board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define RPXClassic_50MHz + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 +#define CONFIG_RPXCLASSIC 1 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */ + + +/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1 */ +#undef CONFIG_FEC_ENET +#ifdef CONFIG_FEC_ENET +#define CFG_DISCOVER_PHY 1 +#endif /* CONFIG_FEC_ENET */ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_ZERO_BOOTDELAY_CHECK 1 + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + + +#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NONSTD | CFG_CMD_ELF) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_RESET_ADDRESS 0x80000000 +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0040000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFA200000 + +/*----------------------------------------------------------------------------- + * I2C Configuration + *----------------------------------------------------------------------------- + */ +#define CONFIG_I2C 1 +#define CFG_I2C_SPEED 50000 +#define CFG_I2C_SLAVE 0x34 + + +/* enable I2C and select the hardware/software driver */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +/* + * Software (bit-bang) I2C driver configuration + */ +#define I2C_PORT 1 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00000010) +#define I2C_TRISTATE (iop->pdir &= ~0x00000010) +#define I2C_READ ((iop->pdat & 0x00000010) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00000010; \ + else iop->pdat &= ~0x00000010 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00000020; \ + else iop->pdat &= ~0x00000020 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + + +# define CFG_I2C_SPEED 50000 +# define CFG_I2C_SLAVE 0x34 +# define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ +# define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF000000 + +#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE 0xFF000000 +/*%%% #define CFG_MONITOR_BASE CFG_FLASH_BASE */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#if 0 +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x20000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#else +#define CFG_ENV_IS_IN_NVRAM 1 +#define CFG_ENV_ADDR 0xfa000100 +#define CFG_ENV_SIZE 0x1000 +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWP) + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_MLRC10) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_PLPRCR ( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF00 +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_SCCR (SCCR_COM00 | SCCR_TBS) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/* #define CFG_DER 0x2002000F */ +/* #define CFG_DER 0 */ +#define CFG_DER 0x0082000F + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */ +#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */ + +/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */ +#define CFG_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI) + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) + +/* + * BR1 and OR1 (SDRAM) + * + */ +#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ +#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000E00 + +#define CFG_OR1_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* RPXLITE mem setting */ +#define CFG_BR3_PRELIM 0xFA400001 /* BCSR */ +#define CFG_OR3_PRELIM 0xff7f8970 +#define CFG_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ +#define CFG_OR4_PRELIM 0xFFF80970 + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 58 + +/* + * Refresh clock Prescalar + */ +#define CFG_MPTPR MPTPR_PTP_DIV8 + +/* + * MAMR settings for SDRAM + */ + +/* 10 column SDRAM */ +#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \ + MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ +/* Configuration variable added by yooth. */ +/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ + +/* + * BCSRx + * + * Board Status and Control Registers + * + */ + +#define BCSR0 0xFA400000 +#define BCSR1 0xFA400001 +#define BCSR2 0xFA400002 +#define BCSR3 0xFA400003 + +#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ +#define BCSR0_ENNVRAM 0x02 /* CS4# Control */ +#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ +#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ +#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ +#define BCSR0_COLTEST 0x20 +#define BCSR0_ETHLPBK 0x40 +#define BCSR0_ETHEN 0x80 + +#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ +#define BCSR1_PCVCTL6 0x02 +#define BCSR1_PCVCTL5 0x04 +#define BCSR1_PCVCTL4 0x08 +#define BCSR1_IPB5SEL 0x10 + +#define BCSR2_MIIRST 0x80 +#define BCSR2_MIIPWRDWN 0x40 +#define BCSR2_MIICTL 0x08 + +#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */ +#define BCSR3_BWNVR 0x02 /* NVRAM Battery */ +#define BCSR3_RDY_BSY 0x04 /* Flash Operation */ +#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */ +#define BCSR3_D27 0x10 /* Dip Switch settings */ +#define BCSR3_D26 0x20 +#define BCSR3_D25 0x40 +#define BCSR3_D24 0x80 + + +/* + * Environment setting + */ + +/* #define CONFIG_ETHADDR 00:10:EC:00:2C:A2 */ +/* #define CONFIG_IPADDR 10.10.106.1 */ +/* #define CONFIG_SERVERIP 10.10.104.11 */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h new file mode 100644 index 00000000000..04293f3e964 --- /dev/null +++ b/include/configs/RPXlite.h @@ -0,0 +1,392 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr + * U-Boot port on RPXlite board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define RPXLite_50MHz + +/* + * High Level Configuration Options + * (easy to change) + */ + +#undef CONFIG_MPC860 +#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ +#define CONFIG_RPXLITE 1 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */ +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0040000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFA200000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFC00000 +/*%%% #define CFG_FLASH_BASE 0xFFF00000 */ +#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE 0xFFF00000 +/*%%% #define CFG_MONITOR_BASE CFG_FLASH_BASE */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 19 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_MLRC10) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/*%%%#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF00 +/* up to 50 MHz we use a 1:1 clock */ +#define CFG_SCCR (SCCR_COM11 | SCCR_TBS) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0 and OR0 (FLASH) + */ + +#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */ +#define CFG_PRELIM_OR_AM 0xFE000000 /* OR addr mask */ + +/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */ +#define CFG_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI) + +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) + +/* + * BR1 and OR1 (SDRAM) + * + */ +#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ +#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000E00 + +#define CFG_OR1_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* RPXLITE mem setting */ +#define CFG_BR3_PRELIM 0xFA400001 /* BCSR */ +#define CFG_OR3_PRELIM 0xFFFF8910 +#define CFG_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ +#define CFG_OR4_PRELIM 0xFFFE0970 + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 58 + +/* + * Refresh clock Prescalar + */ +#define CFG_MPTPR MPTPR_PTP_DIV8 + +/* + * MAMR settings for SDRAM + */ + +/* 10 column SDRAM */ +#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 | \ + MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ +/* Configuration variable added by yooth. */ +/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ + +/* + * BCSRx + * + * Board Status and Control Registers + * + */ + +#define BCSR0 0xFA400000 +#define BCSR1 0xFA400001 +#define BCSR2 0xFA400002 +#define BCSR3 0xFA400003 + +#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ +#define BCSR0_ENNVRAM 0x02 /* CS4# Control */ +#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ +#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ +#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ +#define BCSR0_COLTEST 0x20 +#define BCSR0_ETHLPBK 0x40 +#define BCSR0_ETHEN 0x80 + +#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ +#define BCSR1_PCVCTL6 0x02 +#define BCSR1_PCVCTL5 0x04 +#define BCSR1_PCVCTL4 0x08 +#define BCSR1_IPB5SEL 0x10 + +#define BCSR2_ENPA5HDR 0x08 /* USB Control */ +#define BCSR2_ENUSBCLK 0x10 +#define BCSR2_USBPWREN 0x20 +#define BCSR2_USBSPD 0x40 +#define BCSR2_USBSUSP 0x80 + +#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */ +#define BCSR3_BWNVR 0x02 /* NVRAM Battery */ +#define BCSR3_RDY_BSY 0x04 /* Flash Operation */ +#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */ +#define BCSR3_D27 0x10 /* Dip Switch settings */ +#define BCSR3_D26 0x20 +#define BCSR3_D25 0x40 +#define BCSR3_D24 0x80 + + +/* + * Environment setting + */ + +#define CONFIG_ETHADDR 00:10:EC:00:1D:0B +#define CONFIG_IPADDR 192.168.1.65 +#define CONFIG_SERVERIP 192.168.1.27 + +#endif /* __CONFIG_H */ diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h new file mode 100644 index 00000000000..c36467263ae --- /dev/null +++ b/include/configs/RPXsuper.h @@ -0,0 +1,505 @@ +#ifndef __CONFIG_H +#define __CONFIG_H + + +/***************************************************************************** + * + * These settings must match the way _your_ board is set up + * + *****************************************************************************/ +/* for the AY-Revision which does not use the HRCW */ +#define CFG_DEFAULT_IMMR 0x00010000 + +/* What is the oscillator's (UX2) frequency in Hz? */ +#define CONFIG_8260_CLKIN (66 * 1000 * 1000) + +/* How is switch S2 set? We really only want the MODCK[1-3] bits, so + * only the 3 least significant bits are important. +*/ +#define CFG_SBC_S2 0x04 + +/* What should MODCK_H be? It is dependent on the oscillator + * frequency, MODCK[1-3], and desired CPM and core frequencies. + * Some example values (all frequencies are in MHz): + * + * MODCK_H MODCK[1-3] Osc CPM Core + * 0x2 0x2 33 133 133 + * 0x2 0x4 33 133 200 + * 0x5 0x5 66 133 133 + * 0x5 0x7 66 133 200 + */ +#define CFG_SBC_MODCK_H 0x06 + +#define CFG_SBC_BOOT_LOW 1 /* only for HRCW */ +#undef CFG_SBC_BOOT_LOW + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/sbc8260/config.mk + * The main FLASH is whichever is connected to *CS0. U-Boot expects + * this to be the SIMM. + */ +#define CFG_FLASH0_BASE 0x80000000 +#define CFG_FLASH0_SIZE 16 + +/* What should the base address of the secondary FLASH be and how big + * is it (in Mbytes)? The secondary FLASH is whichever is connected + * to *CS6. U-Boot expects this to be the on board FLASH. If you don't + * want it enabled, don't define these constants. + */ +#define CFG_FLASH1_BASE 0 +#define CFG_FLASH1_SIZE 0 +#undef CFG_FLASH1_BASE +#undef CFG_FLASH1_SIZE + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CFG_SDRAM0_BASE 0x00000000 +#define CFG_SDRAM0_SIZE 64 + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CFG_SDRAM1_BASE 0x04000000 +#define CFG_SDRAM1_SIZE 32 + +/* What should be the base address of the LEDs and switch S0? + * If you don't want them enabled, don't define this. + */ +#define CFG_LED_BASE 0x00000000 + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere. + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on neither */ +#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ +#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ +#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */ + +#if ( CONFIG_ETHER_INDEX == 3 ) + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK16 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Half Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) +# define CFG_CPMFCR_RAMTYPE 0 +/*#define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ +# define CFG_FCC_PSMR 0 + +#else /* CONFIG_ETHER_INDEX */ +# error "on RPX Super ethernet must be FCC3" +#endif /* CONFIG_ETHER_INDEX */ + +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +/* Define this to reserve an entire FLASH sector (256 KB) for + * environment variables. Otherwise, the environment will be + * put in the same sector as U-Boot, and changing variables + * will erase U-Boot temporarily + */ +#define CFG_ENV_IN_OWN_SECT + +/* Define to allow the user to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* What should the console's baud rate be? */ +#define CONFIG_BAUDRATE 115200 + +/* Ethernet MAC address */ +#define CONFIG_ETHADDR 08:00:22:50:70:63 + +#define CONFIG_IPADDR 192.168.1.99 +#define CONFIG_SERVERIP 192.168.1.3 + +/* Set to a positive value to delay for running BOOTCOMMAND */ +#define CONFIG_BOOTDELAY -1 + +/* undef this to save memory */ +#define CFG_LONGHELP + +/* Monitor Command Prompt */ +#define CFG_PROMPT "=> " + +/* What U-Boot subsytems do you want enabled? */ +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_IMMAP | \ + CFG_CMD_ASKENV | \ + CFG_CMD_ECHO | \ + CFG_CMD_I2C | \ + CFG_CMD_REGINFO & \ + ~CFG_CMD_KGDB ) + +/* Where do the internal registers live? */ +#define CFG_IMMR 0xF0000000 + +/* Where do the on board registers (CS4) live? */ +#define CFG_REGS_BASE 0xFA000000 + +/***************************************************************************** + * + * You should not have to modify any of the following settings + * + *****************************************************************************/ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16) + +#define CFG_MAXARGS 8 /* max number of command args */ + +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x04000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_SDRAM_BASE CFG_SDRAM0_BASE + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + */ +#if defined(CFG_SBC_BOOT_LOW) +# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#else +# define CFG_SBC_HRCW_BOOT_FLAGS (0) +#endif /* defined(CFG_SBC_BOOT_LOW) */ + +/* get the HRCW ISB field from CFG_IMMR */ +#define CFG_SBC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\ + ((CFG_IMMR & 0x01000000) >> 7) |\ + ((CFG_IMMR & 0x00100000) >> 4) ) + +#define CFG_HRCW_MASTER (HRCW_BPS11 |\ + HRCW_DPPC11 |\ + CFG_SBC_HRCW_IMMR |\ + HRCW_MMR00 |\ + HRCW_LBPC11 |\ + HRCW_APPC10 |\ + HRCW_CS10PC00 |\ + (CFG_SBC_MODCK_H & HRCW_MODCK_H1111) |\ + CFG_SBC_HRCW_BOOT_FLAGS) + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CFG_RAMBOOT is platform dependent. + */ +#define CFG_MONITOR_BASE (CFG_FLASH0_BASE + 0x00F00000) + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ + +#ifndef CFG_RAMBOOT +# define CFG_ENV_IS_IN_FLASH 1 + +# ifdef CFG_ENV_IN_OWN_SECT +# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CFG_ENV_SECT_SIZE 0x40000 +# else +# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE) +# define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +# define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ +# endif /* CFG_ENV_IN_OWN_SECT */ +#else +# define CFG_ENV_IS_IN_NVRAM 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CFG_ENV_SIZE 0x200 +#endif /* CFG_RAMBOOT */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (/*HID0_ICE |*/\ + /*HID0_DCE |*/\ + HID0_ICFI |\ + HID0_DCI |\ + HID0_IFEM |\ + HID0_ABE) + +#define CFG_HID0_FINAL (/*HID0_ICE |*/\ + HID0_IFEM |\ + HID0_ABE |\ + HID0_EMCP) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register + *----------------------------------------------------------------------- + */ +#define CFG_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR (BCR_EBM |\ + BCR_PLDP |\ + BCR_EAV |\ + BCR_NPQM0) + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ + +#define CFG_SIUMCR (SIUMCR_L2CPC01 |\ + SIUMCR_APPC10 |\ + SIUMCR_CS10PC01) + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#define CFG_SYPCR (SYPCR_SWTC |\ + SYPCR_BMT |\ + SYPCR_PBME |\ + SYPCR_LBME |\ + SYPCR_SWRI |\ + SYPCR_SWP) + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC |\ + TMCNTSC_ALR |\ + TMCNTSC_TCF |\ + TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS |\ + PISCR_PTF |\ + PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CFG_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90) + * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60) + * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60) + * 3 unused + * 4 60x GPCM 8 bit Board Regs, LEDs, switches + * 5 unused + * 6 unused + * 7 unused + * 8 PCMCIA + * 9 unused + * 10 unused + * 11 unused +*/ + +/* Bank 0 - FLASH + * + */ +#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_DECC_NONE |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_6_CLK |\ + ORxG_EHTR) + +/* Bank 1 - SDRAM + * + */ +#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A8 |\ + ORxS_NUMR_12 |\ + ORxS_IBID) + +#define CFG_PSDMR 0x014DA412 +#define CFG_PSRT 0x79 + + +/* Bank 2 - SDRAM + * + */ +#define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_L |\ + BRx_V) + +#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + +#define CFG_LSDMR 0x0169A512 +#define CFG_LSRT 0x79 + +#define CFG_MPTPR (0x0800 & MPTPR_PTP_MSK) + +/* Bank 4 - On board registers + * + */ +#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR4_PRELIM (ORxG_AM_MSK |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ + + diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h new file mode 100644 index 00000000000..f6bc5722ac9 --- /dev/null +++ b/include/configs/ep8260.h @@ -0,0 +1,689 @@ +/* + * (C) Copyright 2002 + * Frank Panno <fpanno@delphintech.com>, Delphin Technology AG + * + * This file is based on similar values for other boards found in other + * U-Boot config files, and some that I found in the EP8260 manual. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + * + * Note: my board is a "SBC 8260 H, V.1.1" + * - 64M 60x Bus SDRAM + * - 32M Local Bus SDRAM + * - 16M Flash (4 x AM29DL323DB90WDI) + * - 128k NVRAM with RTC + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* What is the oscillator's (UX2) frequency in Hz? */ +#define CONFIG_8260_CLKIN (66 * 1000 * 1000) + +/*----------------------------------------------------------------------- + * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual + *----------------------------------------------------------------------- + * What should MODCK_H be? It is dependent on the oscillator + * frequency, MODCK[1-3], and desired CPM and core frequencies. + * Here are some example values (all frequencies are in MHz): + * + * MODCK_H MODCK[1-3] Osc CPM Core + * ------- ---------- --- --- ---- + * 0x2 0x2 33 133 133 + * 0x2 0x3 33 133 166 + * 0x2 0x4 33 133 200 + * 0x2 0x5 33 133 233 + * 0x2 0x6 33 133 266 + * + * 0x5 0x5 66 133 133 + * 0x5 0x6 66 133 166 + * 0x5 0x7 66 133 200 * + * 0x6 0x0 66 133 233 + * 0x6 0x1 66 133 266 + * 0x6 0x2 66 133 300 + */ +#define CFG_SBC_MODCK_H 0x05 + +/* Define this if you want to boot from 0x00000100. If you don't define + * this, you will need to program the bootloader to 0xfff00000, and + * get the hardware reset config words at 0xfe000000. The simplest + * way to do that is to program the bootloader at both addresses. + * It is suggested that you just let U-Boot live at 0x00000000. + */ +/* #define CFG_SBC_BOOT_LOW 1 */ /* only for HRCW */ +/* #undef CFG_SBC_BOOT_LOW */ + +/* The reset command will not work as expected if the reset address does + * not point to the correct address. + */ + +#define CFG_RESET_ADDRESS 0xFFF00100 + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain TEXT_BASE from board/ep8260/config.mk + * The main FLASH is whichever is connected to *CS0. U-Boot expects + * this to be the SIMM. + */ +#define CFG_FLASH0_BASE 0xFF000000 +#define CFG_FLASH0_SIZE 16 + +/* What should the base address of the secondary FLASH be and how big + * is it (in Mbytes)? The secondary FLASH is whichever is connected + * to *CS6. U-Boot expects this to be the on board FLASH. If you don't + * want it enabled, don't define these constants. + */ +#define CFG_FLASH1_BASE 0 +#define CFG_FLASH1_SIZE 0 +#undef CFG_FLASH1_BASE +#undef CFG_FLASH1_SIZE + +/* What should be the base address of SDRAM DIMM (60x bus) and how big is + * it (in Mbytes)? +*/ +#define CFG_SDRAM0_BASE 0x00000000 +#define CFG_SDRAM0_SIZE 64 + +/* define CFG_LSDRAM if you want to enable the 32M SDRAM on the + * local bus (8260 local bus is NOT cacheable!) +*/ +/* #define CFG_LSDRAM */ +#undef CFG_LSDRAM + +#ifdef CFG_LSDRAM +/* What should be the base address of SDRAM DIMM (local bus) and how big is + * it (in Mbytes)? +*/ + #define CFG_SDRAM1_BASE 0x04000000 + #define CFG_SDRAM1_SIZE 32 +#else + #define CFG_SDRAM1_BASE 0 + #define CFG_SDRAM1_SIZE 0 + #undef CFG_SDRAM1_BASE + #undef CFG_SDRAM1_SIZE +#endif /* CFG_LSDRAM */ + +/* What should be the base address of NVRAM and how big is + * it (in Bytes) + */ +#define CFG_NVRAM_BASE_ADDR 0xFa080000 +#define CFG_NVRAM_SIZE (128*1024)-16 + +/* The RTC is a Dallas DS1556 + */ +#define CONFIG_RTC_DS1556 + +/* What should be the base address of the LEDs and switch S0? + * If you don't want them enabled, don't define this. + */ +#define CFG_LED_BASE 0x00000000 +#undef CFG_LED_BASE + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere. + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on neither */ +#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ +#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ +#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */ + +#if ( CONFIG_ETHER_INDEX == 3 ) + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK16 + * - RAM for BD/Buffers is on the local Bus (see 28-13) + * - Enable Half Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) + +/* + * - RAM for BD/Buffers is on the local Bus (see 28-13) + */ +#ifdef CFG_LSDRAM + #define CFG_CPMFCR_RAMTYPE 3 +#else /* CFG_LSDRAM */ + #define CFG_CPMFCR_RAMTYPE 0 +#endif /* CFG_LSDRAM */ + +/* - Enable Half Duplex in FSMR */ +/* # define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ +# define CFG_FCC_PSMR 0 + +#else /* CONFIG_ETHER_INDEX */ +# error "on EP8260 ethernet must be FCC3" +#endif /* CONFIG_ETHER_INDEX */ + +/* + * select i2c support configuration + * + * Supported configurations are {none, software, hardware} drivers. + * If the software driver is chosen, there are some additional + * configuration items that the driver uses to drive the port pins. + */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#ifdef CONFIG_SOFT_I2C +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + +/* #define CONFIG_RTC_DS174x */ + +/* Define this to reserve an entire FLASH sector (256 KB) for + * environment variables. Otherwise, the environment will be + * put in the same sector as U-Boot, and changing variables + * will erase U-Boot temporarily + */ +#define CFG_ENV_IN_OWN_SECT + +/* Define to allow the user to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* What should the console's baud rate be? */ +/* #define CONFIG_BAUDRATE 57600 */ +#define CONFIG_BAUDRATE 115200 + +/* Ethernet MAC address */ +#define CONFIG_ETHADDR 00:10:EC:00:30:8C + +#define CONFIG_IPADDR 192.168.254.130 +#define CONFIG_SERVERIP 192.168.254.49 + +/* Set to a positive value to delay for running BOOTCOMMAND */ +#define CONFIG_BOOTDELAY -1 + +/* undef this to save memory */ +#define CFG_LONGHELP + +/* Monitor Command Prompt */ +#define CFG_PROMPT "=> " + +/* Define this variable to enable the "hush" shell (from + Busybox) as command line interpreter, thus enabling + powerful command line syntax like + if...then...else...fi conditionals or `&&' and '||' + constructs ("shell scripts"). + If undefined, you get the old, much simpler behaviour + with a somewhat smapper memory footprint. +*/ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " + +/* What U-Boot subsytems do you want enabled? */ +/* +*/ +#define CONFIG_COMMANDS ( CFG_CMD_ALL & \ + ~CFG_CMD_BSP & \ + ~CFG_CMD_DCR & \ + ~CFG_CMD_DHCP & \ + ~CFG_CMD_DOC & \ + ~CFG_CMD_EEPROM & \ + ~CFG_CMD_FDC & \ + ~CFG_CMD_HWFLOW & \ + ~CFG_CMD_IDE & \ + ~CFG_CMD_JFFS2 & \ + ~CFG_CMD_KGDB & \ + ~CFG_CMD_MII & \ + ~CFG_CMD_PCI & \ + ~CFG_CMD_PCMCIA & \ + ~CFG_CMD_SCSI & \ + ~CFG_CMD_USB & \ + ~CFG_CMD_VFD & \ + ~CFG_CMD_DTT ) + +/* Where do the internal registers live? */ +#define CFG_IMMR 0xF0000000 +#define CFG_DEFAULT_IMMR 0x00010000 + +/* Where do the on board registers (CS4) live? */ +#define CFG_REGS_BASE 0xFA000000 + +/***************************************************************************** + * + * You should not have to modify any of the following settings + * + *****************************************************************************/ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_EP8260 11 /* on an Embedded Planet EP8260 Board, Rev. 11 */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16) + +#define CFG_MAXARGS 8 /* max number of command args */ + +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#ifdef CFG_LSDRAM + #define CFG_MEMTEST_START 0x04000000 /* memtest works on */ + #define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ +#else + #define CFG_MEMTEST_START 0x00000000 /* memtest works on */ + #define CFG_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */ +#endif /* CFG_LSDRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ +#define CFG_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CFG_FLASH_BASE CFG_FLASH0_BASE +#define CFG_SDRAM_BASE CFG_SDRAM0_BASE + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + */ + +#if defined(CFG_SBC_BOOT_LOW) +# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#else +# define CFG_SBC_HRCW_BOOT_FLAGS (0x00000000) +#endif /* defined(CFG_SBC_BOOT_LOW) */ + +/* get the HRCW ISB field from CFG_IMMR */ +/* +#define CFG_SBC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\ + ((CFG_IMMR & 0x01000000) >> 7) |\ + ((CFG_IMMR & 0x00100000) >> 4) ) + +#define CFG_HRCW_MASTER (HRCW_EBM |\ + HRCW_L2CPC01 |\ + CFG_SBC_HRCW_IMMR |\ + HRCW_APPC10 |\ + HRCW_CS10PC01 |\ + HRCW_MODCK_H0101 |\ + CFG_SBC_HRCW_BOOT_FLAGS) +*/ +#define CFG_HRCW_MASTER 0x10400245 + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CFG_RAMBOOT is platform dependent. + */ +#define CFG_MONITOR_BASE TEXT_BASE + + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ + +#ifndef CFG_RAMBOOT +# define CFG_ENV_IS_IN_FLASH 1 + +# ifdef CFG_ENV_IN_OWN_SECT +# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CFG_ENV_SECT_SIZE 0x40000 +# else +# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE) +# define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +# define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ +# endif /* CFG_ENV_IN_OWN_SECT */ +#else +# define CFG_ENV_IS_IN_NVRAM 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CFG_ENV_SIZE 0x200 +#endif /* CFG_RAMBOOT */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE |\ + HID0_DCE |\ + HID0_ICFI |\ + HID0_DCI |\ + HID0_IFEM |\ + HID0_ABE) +#ifdef CFG_LSDRAM +/* 8260 local bus is NOT cacheable */ +#define CFG_HID0_FINAL (/*HID0_ICE |*/\ + HID0_IFEM |\ + HID0_ABE |\ + HID0_EMCP) +#else /* !CFG_LSDRAM */ +#define CFG_HID0_FINAL (HID0_ICE |\ + HID0_IFEM |\ + HID0_ABE |\ + HID0_EMCP) +#endif /* CFG_LSDRAM */ + +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register + *----------------------------------------------------------------------- + */ +#define CFG_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +/*#define CFG_BCR (BCR_EBM |\ + BCR_PLDP |\ + BCR_EAV |\ + BCR_NPQM1) +*/ +#define CFG_BCR 0x80C08000 +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ + +#define CFG_SIUMCR (SIUMCR_L2CPC01 |\ + SIUMCR_APPC10 |\ + SIUMCR_CS10PC01) + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#ifdef CFG_LSDRAM +#define CFG_SYPCR (SYPCR_SWTC |\ + SYPCR_BMT |\ + SYPCR_PBME |\ + SYPCR_LBME |\ + SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC |\ + SYPCR_BMT |\ + SYPCR_PBME |\ + SYPCR_SWP) +#endif +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC |\ + TMCNTSC_ALR |\ + TMCNTSC_TCF |\ + TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +/*#define CFG_PISCR (PISCR_PS |\ + PISCR_PTF |\ + PISCR_PTE)*/ +#define CFG_PISCR 0 +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CFG_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/*----------------------------------------------------------------------- + * MPTPR - Memory Refresh Timer Prescale Register 10-32 + *----------------------------------------------------------------------- + */ +#define CFG_MPTPR (0x0A00 & MPTPR_PTP_MSK) + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90WDI) + * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Micron 48LC8M16A2TG) + * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Micron 48LC8M16A2TG) + * 3 unused + * 4 60x GPCM 8 bit Board Regs, NVRTC + * 5 unused + * 6 unused + * 7 unused + * 8 PCMCIA + * 9 unused + * 10 unused + * 11 unused +*/ + +/*----------------------------------------------------------------------- + * BRx - Base Register + * Ref: Section 10.3.1 on page 10-14 + * ORx - Option Register + * Ref: Section 10.3.2 on page 10-18 + *----------------------------------------------------------------------- + */ + +/* Bank 0 - FLASH + * + */ +#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_DECC_NONE |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_6_CLK |\ + ORxG_EHTR) + +/* Bank 1 - SDRAM + * PSDRAM + */ +#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A6 |\ + ORxS_NUMR_12) + +#define CFG_PSDMR 0xC34E2462 +#define CFG_PSRT 0x64 + + +#ifdef CFG_LSDRAM +/* Bank 2 - SDRAM + * LSDRAM + */ + + #define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_L |\ + BRx_V) + + #define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + + #define CFG_LSDMR 0x416A2562 + #define CFG_LSRT 0x64 +#else + #define CFG_LSRT 0x0 +#endif /* CFG_LSDRAM */ + +/* Bank 4 - On board registers + * NVRTC and BCSR + */ +#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) +/* +#define CFG_OR4_PRELIM (ORxG_AM_MSK |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_10_CLK |\ + ORxG_TRLX) +*/ +#define CFG_OR4_PRELIM 0xfff00854 + +/* Bank 8 - On board registers + * PCMCIA (currently not working!) + */ +#define CFG_BR8_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR8_PRELIM (ORxG_AM_MSK |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SETA |\ + ORxG_SCY_10_CLK) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ |