diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/spc1920.h | 405 |
1 files changed, 0 insertions, 405 deletions
diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h deleted file mode 100644 index 127de000f0f..00000000000 --- a/include/configs/spc1920.h +++ /dev/null @@ -1,405 +0,0 @@ -/* - * (C) Copyright 2006 - * Markus Klotzbuecher, DENX Software Engineering, mk@denx.de - * - * Configuation settings for the SPC1920 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __H -#define __CONFIG_H - -#define CONFIG_SPC1920 1 /* SPC1920 board */ -#define CONFIG_MPC885 1 /* MPC885 CPU */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_8xx_CONS_SMC1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_MII -#define CONFIG_MII_INIT 1 -#undef CONFIG_ETHER_ON_FEC1 -#define CONFIG_ETHER_ON_FEC2 -#define FEC_ENET -#define CONFIG_FEC2_PHY 1 - -#define CONFIG_BAUDRATE 19200 - -/* use PLD CLK4 instead of brg */ -#define CONFIG_SYS_SPC1920_SMC1_CLK4 - -#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz oscillator on EXTCLK */ -#define CONFIG_8xx_CPUCLK_DEFAULT 50000000 -#define CONFIG_SYS_8xx_CPUCLK_MIN 40000000 -#define CONFIG_SYS_8xx_CPUCLK_MAX 133000000 - -#define CONFIG_SYS_RESET_ADDRESS 0xC0000000 - -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_LAST_STAGE_INIT - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NFSBOOTCOMMAND \ - "dhcp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \ - "bootm" - -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \ - "bootm fe080000" - -#undef CONFIG_BOOTARGS - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_BZIP2 /* include support for bzip2 compressed images */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -#define CONFIG_SYS_BAUDRATE_TABLE { 2400, 4800, 9600, 19200 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */ - -#ifdef CONFIG_BZIP2 -#define CONFIG_SYS_MALLOC_LEN (2500 << 10) /* Reserve ~2.5 MB for malloc() */ -#else -#define CONFIG_SYS_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */ -#endif /* CONFIG_BZIP2 */ - -#define CONFIG_SYS_ALLOC_DPRAM 1 /* use allocation routines */ - -/* - * Flash - */ -/*----------------------------------------------------------------------- - * Flash organisation - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max num of sects on one chip */ - -/* Environment is in flash */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x40000 /* We use one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - -#define CONFIG_ENV_OVERWRITE - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ - -#ifdef CONFIG_CMD_DATE -# define CONFIG_RTC_DS3231 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#endif - -/*----------------------------------------------------------------------- - * I2C configuration - */ -#if defined(CONFIG_CMD_I2C) -/* enable I2C and select the hardware/software driver */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -/* - * Software (bit-bang) I2C driver configuration - */ -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ - -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_FRC) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -/* #define CONFIG_SYS_SCCR SCCR_TBS */ -#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - -/*----------------------------------------------------------------------- - * DER - Debug Enable Register - *----------------------------------------------------------------------- - * Set to zero to prevent the processor from entering debug mode - */ -#define CONFIG_SYS_DER 0 - - -/* Because of the way the 860 starts up and assigns CS0 the entire - * address space, we have to set the memory controller differently. - * Normally, you write the option register first, and then enable the - * chip select by writing the base register. For CS0, you must write - * the base register first, followed by the option register. - */ - - -/* - * Init Memory Controller: - */ - -/* BR0 and OR0 (FLASH) */ -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ - - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* - * FLASH timing: - */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \ - OR_SCY_6_CLK | OR_EHTR | OR_BI) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - - -/* - * SDRAM CS1 UPMB - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE_PRELIM CONFIG_SYS_SDRAM_BASE -#define SDRAM_MAX_SIZE 0x4000000 /* max 64 MB */ - -#define CONFIG_SYS_PRELIM_OR1_AM 0xF0000000 -/* #define CONFIG_SYS_OR1_TIMING OR_CSNT_SAM/\* | OR_G5LS /\\* *\\/ *\/ */ -#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */ - -#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR1_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING) -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V) - -/* #define CONFIG_SYS_OR1_FINAL ((CONFIG_SYS_OR1_AM & OR_AM_MSK) | CONFIG_SYS_OR1_TIMING) */ -/* #define CONFIG_SYS_BR1_FINAL ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V) */ - -#define CONFIG_SYS_PTB_PER_CLK ((4096 * 16 * 1000) / (4 * 64)) -#define CONFIG_SYS_PTA_PER_CLK 195 -#define CONFIG_SYS_MBMR_PTB 195 -#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV16 -#define CONFIG_SYS_MAR 0x88 - -#define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ - MBMR_AMB_TYPE_0 | \ - MBMR_G0CLB_A10 | \ - MBMR_DSB_1_CYCL | \ - MBMR_RLFB_1X | \ - MBMR_WLFB_1X | \ - MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */ - -#define CONFIG_SYS_MBMR_9COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ - MBMR_AMB_TYPE_1 | \ - MBMR_G0CLB_A10 | \ - MBMR_DSB_1_CYCL | \ - MBMR_RLFB_1X | \ - MBMR_WLFB_1X | \ - MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */ - - -/* - * DSP Host Port Interface CS3 - */ -#define CONFIG_SYS_SPC1920_HPI_BASE 0x90000000 -#define CONFIG_SYS_PRELIM_OR3_AM 0xF8000000 - -#define CONFIG_SYS_OR3 (CONFIG_SYS_PRELIM_OR3_AM | \ - OR_G5LS | \ - OR_SCY_0_CLK | \ - OR_BI) - -#define CONFIG_SYS_BR3 ((CONFIG_SYS_SPC1920_HPI_BASE & BR_BA_MSK) | \ - BR_MS_UPMA | \ - BR_PS_16 | \ - BR_V) - -#define CONFIG_SYS_MAMR (MAMR_GPL_A4DIS | \ - MAMR_RLFA_5X | \ - MAMR_WLFA_5X) - -#define CONFIG_SPC1920_HPI_TEST - -#ifdef CONFIG_SPC1920_HPI_TEST -#define HPI_REG(x) (*((volatile u16 *) (CONFIG_SYS_SPC1920_HPI_BASE + x))) -#define HPI_HPIC_1 HPI_REG(0) -#define HPI_HPIC_2 HPI_REG(2) -#define HPI_HPIA_1 HPI_REG(0x2000008) -#define HPI_HPIA_2 HPI_REG(0x2000008 + 2) -#define HPI_HPID_INC_1 HPI_REG(0x1000004) -#define HPI_HPID_INC_2 HPI_REG(0x1000004 + 2) -#define HPI_HPID_NOINC_1 HPI_REG(0x300000c) -#define HPI_HPID_NOINC_2 HPI_REG(0x300000c + 2) -#endif /* CONFIG_SPC1920_HPI_TEST */ - -/* - * Ramtron FM18L08 FRAM 32KB on CS4 - */ -#define CONFIG_SYS_SPC1920_FRAM_BASE 0x80100000 -#define CONFIG_SYS_PRELIM_OR4_AM 0xffff8000 -#define CONFIG_SYS_OR4 (CONFIG_SYS_PRELIM_OR4_AM | \ - OR_ACS_DIV2 | \ - OR_BI | \ - OR_SCY_4_CLK | \ - OR_TRLX) - -#define CONFIG_SYS_BR4 ((CONFIG_SYS_SPC1920_FRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) - -/* - * PLD CS5 - */ -#define CONFIG_SYS_SPC1920_PLD_BASE 0x80000000 -#define CONFIG_SYS_PRELIM_OR5_AM 0xffff8000 - -#define CONFIG_SYS_OR5_PRELIM (CONFIG_SYS_PRELIM_OR5_AM | \ - OR_CSNT_SAM | \ - OR_ACS_DIV1 | \ - OR_BI | \ - OR_SCY_0_CLK | \ - OR_TRLX) - -#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SPC1920_PLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) - -#endif /* __CONFIG_H */ |