diff options
Diffstat (limited to 'include/configs')
31 files changed, 1268 insertions, 188 deletions
diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h index 5b54f30e08d..bc30977fd7a 100644 --- a/include/configs/BC3450.h +++ b/include/configs/BC3450.h @@ -282,17 +282,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet - * hasn't been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#if defined(CFG_IPBSPEED_133) -# define CFG_PCISPEED_66 /* define for 66MHz speed */ +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) +# define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -488,7 +488,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 # define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else # define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index 598811240a7..73be06950bc 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -167,9 +167,9 @@ * IPB Bus clocking configuration. */ #if defined(CONFIG_LITE5200B) -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #else -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif #endif /* CONFIG_MPC5200 */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h new file mode 100644 index 00000000000..697631345f6 --- /dev/null +++ b/include/configs/MPC8313ERDB.h @@ -0,0 +1,561 @@ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* + * mpc8313epb board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 +#define CONFIG_MPC83XX 1 +#define CONFIG_MPC831X 1 +#define CONFIG_MPC8313 1 +#define CONFIG_MPC8313ERDB 1 + +#define CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI + +#ifdef CFG_66MHZ +#define CONFIG_83XX_CLKIN 66666667 /* in Hz */ +#elif defined(CFG_33MHZ) +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#else +#error Unknown oscillator frequency. +#endif + +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +#define CFG_IMMR 0xE0000000 + +#define CFG_MEMTEST_START 0x00001000 +#define CFG_MEMTEST_END 0x07f00000 + +/* Early revs of this board will lock up hard when attempting + * to access the PMC registers, unless a JTAG debugger is + * connected, or some resistor modifications are made. + */ +#define CFG_8313ERDB_BROKEN_PMC 1 + +#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE + +/* + * Manually set up DDR parameters, as this board does not + * seem to have the SPD connected to I2C. + */ +#define CFG_DDR_SIZE 128 /* MB */ +#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \ + | 0x00040000 /* TODO */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) + /* 0x80840102 */ + +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ + | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ + | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) + /* 0x00220802 */ +#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ + | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ + | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ + | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ + | (13 << TIMING_CFG1_REFREC_SHIFT ) \ + | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) + /* 0x3935d322 */ +#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \ + | (31 << TIMING_CFG2_CPO_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ + | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ + | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ + | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) ) + /* 0x0f9048ca */ /* P9-45,may need tuning */ +#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \ + | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) + /* 0x03200064 */ +#if defined(CONFIG_DDR_2T_TIMING) +#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ + | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \ + | SDRAM_CFG_2T_EN \ + | SDRAM_CFG_DBW_32 ) +#else +#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ + | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \ + | SDRAM_CFG_32_BE ) + /* 0x43080000 */ +#endif +#define CFG_SDRAM_CFG2 0x00401000; +/* set burst length to 8 for 32-bit data path */ +#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \ + | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) ) + /* 0x44400232 */ +#define CFG_DDR_MODE_2 0x8000C000; + +#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 + /*0x02000000*/ +#define CFG_DDRCDR_VALUE ( DDRCDR_EN \ + | DDRCDR_PZ_NOMZ \ + | DDRCDR_NZ_NOMZ \ + | DDRCDR_M_ODR ) + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */ +#define CFG_FLASH_SIZE 8 /* flash size in MB */ +#define CFG_FLASH_EMPTY_INFO /* display empty sectors */ +#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_9 \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD ) + /* 0xFF006FF7 TODO SLOW 16 MB flash size */ +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */ + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 135 /* sectors per device */ + +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#endif + +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/ + +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Local Bus LCRR and LBCR regs + */ +#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */ +#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \ + | (0xFF << LBCR_BMT_SHIFT) \ + | 0xF ) /* 0x0004ff0f */ + +#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */ + +/* drivers/nand/nand.c */ +#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE + +#define CFG_BR1_PRELIM ( CFG_NAND_BASE \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V ) /* valid */ +#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR ) + /* 0xFFFF8396 */ +#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE +#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ + +#define CFG_VSC7385_BASE 0xF0000000 + +#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */ +#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ +#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ +#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */ +#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */ + +/* local bus read write buffer mapping */ +#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */ +#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */ +#define CFG_LBLAWBAR3_PRELIM 0xFA000000 +#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,8313@0" +#define OF_SOC "soc8313@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc8313@e0000000/serial@4500" + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +/* TSEC */ +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) +#define CONFIG_NET_MULTI + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_MMIO_BASE 0x90000000 +#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE +#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xE2000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +/* + * TSEC configuration + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_GMII 1 /* MII PHY management */ +#define CONFIG_MPC83XX_TSEC1 1 + +#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0" +#define CONFIG_MPC83XX_TSEC2 1 +#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 0x1c +#define TSEC2_PHY_ADDR 4 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Configure on-board RTC + */ +#define CONFIG_RTC_DS1337 +#define CFG_I2C_RTC_ADDR 0x68 + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 + +/* Address and size of Redundant Environment Sector */ +#else + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CFG_BASE_COMMANDS ( CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_DHCP \ + | CFG_CMD_I2C \ + | CFG_CMD_MII \ + | CFG_CMD_DATE \ + | CFG_CMD_PCI) + +#define CONFIG_CMDLINE_EDITING 1 + +#define CFG_RAMBOOT_COMMANDS (CFG_BASE_COMMANDS & \ + ~(CFG_CMD_ENV | CFG_CMD_LOADS)) + +#if defined(CFG_RAMBOOT) +#define CONFIG_COMMANDS CFG_RAMBOOT_COMMANDS +#else +#define CONFIG_COMMANDS CFG_BASE_COMMANDS +#endif + +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 16384 +#define CFG_CACHELINE_SIZE 32 +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ + +#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ + +#ifdef CFG_66MHZ + +/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */ +/* 0x62040000 */ +#define CFG_HRCW_LOW (\ + 0x20000000 /* reserved, must be set */ |\ + HRCWL_DDRCM |\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_CSB_TO_CLKIN_2X1 |\ + HRCWL_CORE_TO_CSB_2X1) + +#elif defined(CFG_33MHZ) + +/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */ +/* 0x65040000 */ +#define CFG_HRCW_LOW (\ + 0x20000000 /* reserved, must be set */ |\ + HRCWL_DDRCM |\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_CSB_TO_CLKIN_5X1 |\ + HRCWL_CORE_TO_CSB_2X1) + +#endif + +/* 0xa0606c00 */ +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_NORMAL) + +/* System IO Config */ +#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ +#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */ + +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) + +#define CFG_HID2 HID2_HBE + +/* DDR @ 0x00000000 */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* PCI @ 0x80000000 */ +#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10) +#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* PCI2 not supported on 8313 */ +#define CFG_IBAT3L (0) +#define CFG_IBAT3U (0) +#define CFG_IBAT4L (0) +#define CFG_IBAT4U (0) + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ +#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) + +/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ +#define CFG_IBAT6L (0xF0000000 | BATL_PP_10) +#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ETHADDR 00:E0:0C:00:95:01 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02 + +#define CONFIG_IPADDR 10.0.0.2 +#define CONFIG_SERVERIP 10.0.0.1 +#define CONFIG_GATEWAYIP 10.0.0.1 +#define CONFIG_NETMASK 255.0.0.0 +#define CONFIG_NETDEV eth1 + +#define CONFIG_HOSTNAME mpc8313erdb +#define CONFIG_ROOTPATH /nfs/root/path +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ +#define CONFIG_FDTFILE mpc8313erdb.dtb + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ +#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ +#define CONFIG_BAUDRATE 115200 + +#define XMK_STR(x) #x +#define MK_STR(x) XMK_STR(x) + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" MK_STR(CONFIG_NETDEV) "\0" \ + "ethprime=TSEC1\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "fdtaddr=400000\0" \ + "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ + "console=ttyS0\0" \ + "setbootargs=setenv bootargs " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ + "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setbootargs;" \ + "run setipargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv rootdev /dev/ram;" \ + "run setbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#undef MK_STR +#undef XMK_STR + +#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 37bbfb336d2..906339e9d88 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -154,6 +154,9 @@ #define CFG_MEMTEST_START 0x1000 /* memtest region */ #define CFG_MEMTEST_END 0x2000 +#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + #ifdef CONFIG_HARD_I2C #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ #endif diff --git a/include/configs/PM520.h b/include/configs/PM520.h index 9c241e67e73..7d91a0160c4 100644 --- a/include/configs/PM520.h +++ b/include/configs/PM520.h @@ -160,7 +160,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h new file mode 100755 index 00000000000..1d2f28d9462 --- /dev/null +++ b/include/configs/SMN42.h @@ -0,0 +1,199 @@ +/* + * (C) Copyright 2007 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * Configuation settings for the SMN42 board from Siemens. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * If we are developing, we might want to start u-boot from ram + * so we MUST NOT initialize critical regs like mem-timing ... + */ +#undef CONFIG_INIT_CRITICAL /* undef for developing */ + +#undef CONFIG_SKIP_LOWLEVEL_INIT +#undef CONFIG_SKIP_RELOCATE_UBOOT + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_ARM7 1 /* This is a ARM7 CPU */ +#define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */ +#define CONFIG_LPC2292 +#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */ + +#undef CONFIG_USE_IRQ /* don't need them anymore */ + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +/* + * select serial console configuration + */ +#define CONFIG_SERIAL1 1 /* we use Serial line 1 */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +/* this would be 0xAE if E0, E1 and E2 were pulled high */ +#define CFG_I2C_SLAVE 0xA0 +#define CFG_I2C_EEPROM_ADDR (0xA0 >> 1) +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +/* not used but required by devices.c */ +#define CFG_I2C_SPEED 10000 + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define SCL 0x00000004 /* P0.2 */ +#define SDA 0x00000008 /* P0.3 */ + +#define I2C_READ ((GET32(IO0PIN) & SDA) ? 1 : 0) +#define I2C_SDA(x) { if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); } +#define I2C_SCL(x) { if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); } +#define I2C_DELAY { udelay(100); } +#define I2C_ACTIVE { unsigned int i2ctmp; \ + i2ctmp = GET32(IO0DIR); \ + i2ctmp |= SDA; \ + PUT32(IO0DIR, i2ctmp); } +#define I2C_TRISTATE { unsigned int i2ctmp; \ + i2ctmp = GET32(IO0DIR); \ + i2ctmp &= ~SDA; \ + PUT32(IO0DIR, i2ctmp); } +#endif /* CONFIG_SOFT_I2C */ + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_FAT | \ + CFG_CMD_MMC | \ + CFG_CMD_NET | \ + CFG_CMD_EEPROM | \ + CFG_CMD_PING) + +#define CONFIG_DOS_PARTITION + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_BOOTDELAY 5 + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "SMN42 # " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x81800000 /* memtest works on */ +#define CFG_MEMTEST_END 0x83000000 /* 24 MB in SRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x81000000 /* default load address + * for uClinux img is here*/ + +#define CFG_SYS_CLK_FREQ 58982400 /* Hz */ +#define CFG_HZ 2048 /* decrementer freq in Hz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SRAM */ +#define PHYS_SDRAM_1 0x81000000 /* SRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB SRAM */ + +/* This is the external flash */ +#define PHYS_FLASH_1 0x80000000 /* Flash Bank #1 */ +#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +/* + * The first entry in CFG_FLASH_BANKS_LIST is a dummy, but it must be present. + */ +#define CFG_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 } +#define CFG_FLASH_ADDR0 0x555 +#define CFG_FLASH_ADDR1 0x2AA +#define CFG_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ + +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ + +#define CFG_ENV_IS_IN_FLASH 1 +/* The Environment Sector is in the CPU-internal flash */ +#define CFG_FLASH_BASE 0 +#define CFG_ENV_OFFSET 0x3C000 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_ENV_OFFSET) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_MMC 1 +/* we use this ethernet chip */ +#define CONFIG_ENC28J60 + +#endif /* __CONFIG_H */ diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h index 8a6e5a61b73..b42cfb6e1fb 100644 --- a/include/configs/TB5200.h +++ b/include/configs/TB5200.h @@ -200,17 +200,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -432,7 +432,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h index f41dbd0ccb1..1cc9ce94f91 100644 --- a/include/configs/TOP5200.h +++ b/include/configs/TOP5200.h @@ -186,7 +186,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 7069b35ad60..7935593febe 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -269,17 +269,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of + * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -594,7 +594,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h index 81757032362..d8686dd39c0 100644 --- a/include/configs/Total5200.h +++ b/include/configs/Total5200.h @@ -183,7 +183,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 35b6a519e32..0f447b004a0 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -34,7 +34,9 @@ #define CONFIG_ACADIA 1 /* Board is Acadia */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405EZ 1 /* Specifc 405EZ support*/ -#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +/* Detect Acadia PLL input clock automatically via CPLD bit */ +#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \ + 66666666 : 33333000) #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_F 1 /* Call misc_init_f */ @@ -107,6 +109,7 @@ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ @@ -120,6 +123,12 @@ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define _CFG_CMD_INCLUDE (CFG_CMD_ALL) +#else +#define CFG_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */ +#define _CFG_CMD_INCLUDE ((CFG_CMD_ALL) & ~(CFG_CMD_FLASH | CFG_CMD_IMLS)) +#endif + #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) @@ -130,6 +139,63 @@ #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_DATA_ADDR + (12 << 10)) /* Copy SPL here*/ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + +#ifdef CFG_ENV_IS_IN_NAND +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/sequoia/u-boot-nand.lds for details. + */ +#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + /*----------------------------------------------------------------------- * RAM (CRAM) *----------------------------------------------------------------------*/ @@ -207,7 +273,11 @@ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ "cp.b ${fileaddr} fffc0000 ${filesize};" \ "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ + "upd=run load update\0" \ + "nload=tftp 200000 acadia/u-boot-nand.bin\0" \ + "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ + "setenv filesize;saveenv\0" \ + "nupd=run nload nupdate\0" \ "kozio=bootm ffc60000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -224,16 +294,6 @@ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE -#if 0 /* test-only */ -#define TEST_ONLY_NAND -#endif - -#ifdef TEST_ONLY_NAND -#define CMD_NAND CFG_CMD_NAND -#else -#define CMD_NAND 0 -#endif - /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -241,24 +301,24 @@ #define CONFIG_SUPPORT_VFAT -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DHCP | \ - CFG_CMD_DTT | \ - CFG_CMD_DIAG | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - CFG_CMD_FAT | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CMD_NAND | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_USB) +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & _CFG_CMD_INCLUDE) | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DTT | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NAND | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_USB) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -300,7 +360,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -#ifdef TEST_ONLY_NAND /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -308,7 +367,6 @@ #define NAND_MAX_CHIPS 1 #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#endif /*----------------------------------------------------------------------- * Cache Configuration @@ -322,12 +380,16 @@ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ - +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 3 /* Memory Bank 0 (Flash) initialization */ #define CFG_EBC_PB0AP 0x03337200 #define CFG_EBC_PB0CR 0xfe0bc000 +/* Memory Bank 3 (NAND-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x018003c0 +#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000) + /* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/ /* Memory Bank 1 (CRAM) initialization */ #define CFG_EBC_PB1AP 0x030400c0 @@ -336,10 +398,24 @@ /* Memory Bank 2 (CRAM) initialization */ #define CFG_EBC_PB2AP 0x030400c0 #define CFG_EBC_PB2CR 0x020bc000 +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) -/* Memory Bank 3 (NAND-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x018003c0 -#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000) +/* + * When NAND-booting the CRAM EBC setup must be done in sync mode, since the + * NAND-SPL already initialized the CRAM and EBC to sync mode. + */ +/* Memory Bank 1 (CRAM) initialization */ +#define CFG_EBC_PB1AP 0x9C0201C0 +#define CFG_EBC_PB1CR 0x000bc000 + +/* Memory Bank 2 (CRAM) initialization */ +#define CFG_EBC_PB2AP 0x9C0201C0 +#define CFG_EBC_PB2CR 0x020bc000 +#endif /* Memory Bank 4 (CPLD) initialization */ #define CFG_EBC_PB4AP 0x04006000 @@ -351,14 +427,15 @@ * GPIO Setup *----------------------------------------------------------------------*/ #define CFG_GPIO_CRAM_CLK 8 -#define CFG_GPIO_CRAM_WAIT 9 +#define CFG_GPIO_CRAM_WAIT 9 /* GPIO-In */ #define CFG_GPIO_CRAM_ADV 10 -#define CFG_GPIO_CRAM_CRE (32 + 21) +#define CFG_GPIO_CRAM_CRE (32 + 21) /* GPIO-Out */ /*----------------------------------------------------------------------- * Definitions for GPIO_0 setup (PPC405EZ specific) * - * GPIO0[0-3] - External Bus Controller CS_4 - CS_7 Outputs + * GPIO0[0-2] - External Bus Controller CS_4 - CS_6 Outputs + * GPIO0[3] - NAND FLASH Controller CE3 (NFCE3) Output * GPIO0[4] - External Bus Controller Hold Input * GPIO0[5] - External Bus Controller Priority Input * GPIO0[6] - External Bus Controller HLDA Output @@ -374,12 +451,12 @@ * GPIO0[28-30] - Trace Outputs / PWM Inputs * GPIO0[31] - PWM_8 I/O */ -#define CFG_GPIO0_TCR 0xC0000000 -#define CFG_GPIO0_OSRL 0x50000000 -#define CFG_GPIO0_OSRH 0x00000055 -#define CFG_GPIO0_ISR1L 0x00000000 +#define CFG_GPIO0_TCR 0xC0A00000 +#define CFG_GPIO0_OSRL 0x50004400 +#define CFG_GPIO0_OSRH 0x02000055 +#define CFG_GPIO0_ISR1L 0x00001000 #define CFG_GPIO0_ISR1H 0x00000055 -#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TSRL 0x02000000 #define CFG_GPIO0_TSRH 0x00000055 /*----------------------------------------------------------------------- @@ -396,13 +473,13 @@ * GPIO1[16] - SPI_SS_1_N Output * GPIO1[17-20] - Trace Output/External Interrupts IRQ0 - IRQ3 inputs */ -#define CFG_GPIO1_OSRH 0x55455555 +#define CFG_GPIO1_TCR 0xFFFF8414 #define CFG_GPIO1_OSRL 0x40000110 -#define CFG_GPIO1_ISR1H 0x00000000 +#define CFG_GPIO1_OSRH 0x55455555 #define CFG_GPIO1_ISR1L 0x15555445 -#define CFG_GPIO1_TSRH 0x00000000 +#define CFG_GPIO1_ISR1H 0x00000000 #define CFG_GPIO1_TSRL 0x00000000 -#define CFG_GPIO1_TCR 0xFFFF8014 +#define CFG_GPIO1_TSRH 0x00000000 /* * Internal Definitions diff --git a/include/configs/aev.h b/include/configs/aev.h index 8d9f0a16610..6c2a3603787 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -166,17 +166,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -362,7 +362,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index db58a9fa74a..763d1c7a8b4 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -50,7 +50,7 @@ *----------------------------------------------------------------------*/ #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) +#define CFG_MONITOR_BASE TEXT_BASE #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ @@ -104,14 +104,11 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -/* - * Define here the location of the environment variables (FLASH or EEPROM). - * Note: DENX encourages to use redundant environment in FLASH. - */ -#if 1 +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #else -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /*----------------------------------------------------------------------- @@ -133,7 +130,7 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -141,22 +138,89 @@ #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ + +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + +#ifdef CFG_ENV_IS_IN_NAND +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/sequoia/u-boot-nand.lds for details. + */ +#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CFG_NAND_CS 1 +#define CFG_MAX_NAND_DEVICE 2 +#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_BASE_LIST { CFG_NAND_BASE, CFG_NAND_ADDR + 2 } #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 1 +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) +#endif + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------------- */ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ -#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} +#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} +#define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ /*----------------------------------------------------------------------- * I2C diff --git a/include/configs/canmb.h b/include/configs/canmb.h index 2c160a44891..ec6d57e1e69 100644 --- a/include/configs/canmb.h +++ b/include/configs/canmb.h @@ -111,7 +111,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * Flash configuration, expect one 16 Megabyte Bank at most diff --git a/include/configs/cpci5200.h b/include/configs/cpci5200.h index f9586fbcb94..f5efcd911a5 100644 --- a/include/configs/cpci5200.h +++ b/include/configs/cpci5200.h @@ -179,7 +179,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h index 095b5f6dc27..4d813d8be78 100644 --- a/include/configs/hmi1001.h +++ b/include/configs/hmi1001.h @@ -110,7 +110,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index 773d5d2c1d9..ad3cf06e950 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -147,7 +147,7 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * Flash configuration diff --git a/include/configs/lpc2292sodimm.h b/include/configs/lpc2292sodimm.h index 7e515230a33..30e0b10f797 100644..100755 --- a/include/configs/lpc2292sodimm.h +++ b/include/configs/lpc2292sodimm.h @@ -1,12 +1,8 @@ /* - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> + * (C) Copyright 2007 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * - * Configuation settings for the EP7312 board. - * - * Modified to work on Armadillo HT1070 ARM720T board - * (C) Copyright 2005 Rowel Atienza rowel@diwalabs.com + * Configuation settings for the LPC2292SODIMM board from Embedded Artists. * * See file CREDITS for list of people who contributed to this * project. @@ -31,7 +27,7 @@ #define __CONFIG_H /* - * If we are developing, we might want to start armboot from ram + * If we are developing, we might want to start u-boot from ram * so we MUST NOT initialize critical regs like mem-timing ... */ #undef CONFIG_INIT_CRITICAL /* undef for developing */ @@ -105,7 +101,9 @@ #undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ -#define CFG_LOAD_ADDR 0x00040000 /* default load address for armadillo: kernel img is here*/ +#define CFG_LOAD_ADDR 0x00040000 /* default load address for + * armadillo: kernel img is here + */ #define CFG_SYS_CLK_FREQ 58982400 /* Hz */ #define CFG_HZ 2048 /* decrementer freq in Hz */ @@ -154,5 +152,7 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_MMC 1 +/* we use this ethernet chip */ +#define CONFIG_ENC28J60 #endif /* __CONFIG_H */ diff --git a/include/configs/luan.h b/include/configs/luan.h index 9c8769b200b..045a144aad8 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -135,7 +135,8 @@ *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ #define SPD_EEPROM_ADDRESS {0x53, 0x52} /* SPD i2c spd addresses*/ -#undef CONFIG_DDR_ECC /* no ECC support for now */ +#define CONFIG_DDR_ECC 1 /* with ECC support */ +#define CFG_44x_DDR2_CKTR_180 1 /* use 180 deg advance */ /*----------------------------------------------------------------------- * I2C diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h index 621a81c9c56..c2324a04c91 100644 --- a/include/configs/mcc200.h +++ b/include/configs/mcc200.h @@ -169,7 +169,7 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration diff --git a/include/configs/ml401.h b/include/configs/ml401.h index cb159e79dc6..3db287784da 100644 --- a/include/configs/ml401.h +++ b/include/configs/ml401.h @@ -28,6 +28,7 @@ #include "../board/xilinx/ml401/xparameters.h" #define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */ +#define MICROBLAZE_V5 1 #define CONFIG_ML401 1 /* ML401 Board */ /* uart */ @@ -36,11 +37,11 @@ #define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE } /* setting reset address */ -#define CFG_RESET_ADDRESS TEXT_BASE +/*#define CFG_RESET_ADDRESS TEXT_BASE*/ /* ethernet */ #define CONFIG_EMACLITE 1 -#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES +#define XPAR_EMAC_0_DEVICE_ID XPAR_OPB_ETHERNET_0_DEVICE_ID /* gpio */ #define CFG_GPIO_0 1 @@ -58,6 +59,10 @@ #define FREQUENCE XILINX_CLOCK_FREQ #define CFG_TIMER_0_PRELOAD ( FREQUENCE/1000 ) +/* FSL */ +#define CFG_FSL_2 +#define FSL_INTR_2 1 + /* * memory layout - Example * TEXT_BASE = 0x1200_0000; @@ -93,7 +98,8 @@ /* global pointer */ #define CFG_GBL_DATA_SIZE 0x1000 /* size of global data */ -#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */ +/* start of global data */ +#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* monitor code */ #define SIZE 0x40000 @@ -117,6 +123,7 @@ #define CFG_FLASH_EMPTY_INFO 1 /* ?empty sector */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + #define CFG_FLASH_PROTECTION /* hardware flash protection */ #ifdef RAMENV #define CFG_ENV_IS_NOWHERE 1 @@ -135,6 +142,7 @@ #define CFG_ENV_IS_NOWHERE 1 #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE) + #define CFG_FLASH_PROTECTION /* hardware flash protection */ #endif /* !FLASH */ #ifdef FLASH @@ -152,8 +160,13 @@ CFG_CMD_IMI |\ CFG_CMD_NET |\ CFG_CMD_CACHE |\ + CFG_CMD_FAT |\ + CFG_CMD_EXT2 |\ + CFG_CMD_JFFS2 |\ + CFG_CMD_ECHO |\ CFG_CMD_IMLS |\ CFG_CMD_FLASH |\ + CFG_CMD_MFSL |\ CFG_CMD_PING \ ) #else /* !RAMENV */ @@ -174,6 +187,11 @@ CFG_CMD_FLASH |\ CFG_CMD_PING |\ CFG_CMD_ENV |\ + CFG_CMD_FAT |\ + CFG_CMD_EXT2 |\ + CFG_CMD_JFFS2 |\ + CFG_CMD_ECHO |\ + CFG_CMD_MFSL |\ CFG_CMD_SAVES \ ) @@ -189,16 +207,30 @@ CFG_CMD_BDI |\ CFG_CMD_RUN |\ CFG_CMD_LOADS |\ + CFG_CMD_FAT |\ + CFG_CMD_EXT2 |\ CFG_CMD_LOADB |\ CFG_CMD_IMI |\ CFG_CMD_NET |\ CFG_CMD_CACHE |\ + CFG_CMD_MFSL |\ CFG_CMD_PING \ ) #endif /* !FLASH */ /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) +/* JFFS2 partitions */ +#define CONFIG_JFFS2_CMDLINE /* mtdparts command line support */ +#define MTDIDS_DEFAULT "nor0=ml401-0" + +/* default mtd partition table */ +#define MTDPARTS_DEFAULT "mtdparts=ml401-0:256k(u-boot),"\ + "256k(env),3m(kernel),1m(romfs),"\ + "1m(cramfs),-(jffs2)" +#endif + /* Miscellaneous configurable options */ #define CFG_PROMPT "U-Boot-mONStR> " #define CFG_CBSIZE 512 /* size of console buffer */ @@ -207,7 +239,7 @@ #define CFG_LONGHELP #define CFG_LOAD_ADDR 0x12000000 /* default load address */ -#define CONFIG_BOOTDELAY 30 +#define CONFIG_BOOTDELAY 30 #define CONFIG_BOOTARGS "root=romfs" #define CONFIG_HOSTNAME "ml401" #define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm" @@ -221,10 +253,19 @@ #define CFG_HZ 1000 /* system ace */ -/*#define CONFIG_SYSTEMACE -#define DEBUG_SYSTEMACE -#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR -#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH -#define CONFIG_DOS_PARTITION -*/ +#define CONFIG_SYSTEMACE +/* #define DEBUG_SYSTEMACE */ +#define SYSTEMACE_CONFIG_FPGA +#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR +#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH +#define CONFIG_DOS_PARTITION + +#define CONFIG_PREBOOT "echo U-BOOT for ML401;setenv preboot;echo" + +#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" /* hardware flash protection */\ + "nor0=ml401-0\0"\ + "mtdparts=mtdparts=ml401-0:"\ + "256k(u-boot),256k(env),3m(kernel),"\ + "1m(romfs),1m(cramfs),-(jffs2)\0" + #endif /* __CONFIG_H */ diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 5328e8d6b1c..e3899a5ab40 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -26,12 +26,10 @@ #ifndef __CONFIG_H #define __CONFIG_H - /* * High Level Configuration Options */ - /* CPU and board */ #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ @@ -50,7 +48,14 @@ CFG_CMD_MII | \ CFG_CMD_BEDBUG | \ CFG_CMD_NET | \ - CFG_CMD_PING) + CFG_CMD_PING | \ + CFG_CMD_IDE | \ + CFG_CMD_FAT | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_I2C | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DTT) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -71,7 +76,7 @@ #define CONFIG_MPC5xxx_FEC 1 #define CONFIG_PHY_ADDR 0x2 #define CONFIG_PHY_TYPE 0x79c874 - +#define CONFIG_RESET_PHY_R 1 /* * Autobooting @@ -94,42 +99,51 @@ * Default environment settings */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "sdram_test=0\0" \ "netdev=eth0\0" \ "hostname=motionpro\0" \ "netmask=255.255.0.0\0" \ "ipaddr=192.168.160.22\0" \ "serverip=192.168.1.1\0" \ "gatewayip=192.168.1.1\0" \ - "kernel_addr=200000\0" \ + "console=ttyPSC0,115200\0" \ "u-boot_addr=100000\0" \ - "kernel_sector=20\0" \ - "kernel_size=1000\0" \ - "console=ttyS0,115200\0" \ + "kernel_addr=200000\0" \ + "fdt_addr=400000\0" \ + "ramdisk_addr=500000\0" \ + "multi_image_addr=800000\0" \ "rootpath=/opt/eldk-4.1/ppc_6xx\0" \ - "bootfile=/tftpboot/motionpro/uImage\0" \ "u-boot=/tftpboot/motionpro/u-boot.bin\0" \ - "load=tftp $(u-boot_addr) $(u-boot)\0" \ + "bootfile=/tftpboot/motionpro/uImage\0" \ + "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \ + "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \ + "multi_image_file=kernel+initrd+dtb.img\0" \ + "load=tftp ${u-boot_addr} ${u-boot}\0" \ "update=prot off fff00000 fff3ffff; era fff00000 fff3ffff; " \ - "cp.b $(u-boot_addr) fff00000 $(filesize);" \ + "cp.b ${u-boot_addr} fff00000 ${filesize};" \ "prot on fff00000 fff3ffff\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) console=$(console) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):" \ - "$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip;bootm $(kernel_addr) " \ - "$(ramdisk_addr)\0" \ - "net_nfs=tftp $(kernel_addr) $(bootfile); run nfsargs addip; " \ - "bootm $(kernel_addr)\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "fstype=ext3\0" \ - "fatargs=setenv bootargs init=/linuxrc rw\0" \ + "nfsroot=${serverip}:${rootpath}\0" \ + "fat_args=setenv bootargs rw\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off panic=1 " \ + "console=${console}\0" \ + "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip; " \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_self=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; " \ + "tftp ${ramdisk_addr} ${ramdisk_file}; " \ + "run ramargs addip; " \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "fat_multi=run fat_args addip; fatload ide 0:1 " \ + "${multi_image_addr} ${multi_image_file}; " \ + "bootm ${multi_image_addr}\0" \ "" #define CONFIG_BOOTCOMMAND "run net_nfs" - /* * do board-specific init */ @@ -148,6 +162,12 @@ /* + * Set IPB speed to 100MHz + */ +#define CFG_IPBCLK_EQUALS_XLBCLK + + +/* * Memory map */ /* @@ -243,6 +263,84 @@ #define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ #define CONFIG_FLASH_16BIT /* Flash is 16-bit */ +/* + * MTD configuration + */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=motionpro-0" +#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \ + "13m(fs),2m(kernel),256k(uboot)," \ + "64k(env),64k(redund_env),64k(dtb)," \ + "-(user_data)" + +/* + * IDE/ATA configuration + */ +#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CFG_IDE_MAXBUS 1 +#define CFG_IDE_MAXDEVICE 1 +#define CONFIG_IDE_PREINIT + +#define CFG_ATA_DATA_OFFSET 0x0060 +#define CFG_ATA_REG_OFFSET CFG_ATA_DATA_OFFSET +#define CFG_ATA_STRIDE 4 +#define CONFIG_DOS_PARTITION + + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_MODULE 2 /* select I2C module #2 */ +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + + +/* + * EEPROM configuration + */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* DTT driver needs this */ +#define CFG_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ +#define CFG_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */ + + +/* + * RTC configuration + */ +#define CONFIG_RTC_DS1337 1 +#define CFG_I2C_RTC_ADDR 0x68 + + +/* + * Status LED configuration + */ +#define CONFIG_STATUS_LED /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED + +#define ENABLE_GPIO_OUT 0x00000024 +#define LED_ON 0x00000010 + +#ifndef __ASSEMBLY__ +/* + * In case of Motion-PRO, a LED is identified by its corresponding + * GPT Enable and Mode Select Register. + */ +typedef volatile unsigned long * led_id_t; + +extern void __led_init(led_id_t id, int state); +extern void __led_toggle(led_id_t id); +extern void __led_set(led_id_t id, int state); +#endif /* __ASSEMBLY__ */ + + +/* + * Temperature sensor + */ +#define CONFIG_DTT_LM75 1 +#define CONFIG_DTT_SENSORS { 0x49 } + /* * Environment settings @@ -253,6 +351,9 @@ #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_SECT_SIZE 0x10000 +/* Configuration of redundant environment */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) /* * Pin multiplexing configuration @@ -270,11 +371,17 @@ /* + * Motion-PRO's CPLD revision control register + */ +#define CPLD_REV_REGISTER (CFG_CS2_START + 0x06) + + +/* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ @@ -302,4 +409,15 @@ /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */ #define CFG_RESET_ADDRESS 0xfff00100 +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" + #endif /* __CONFIG_H */ diff --git a/include/configs/o2dnt.h b/include/configs/o2dnt.h index 5c05a745dbb..63d0da7d090 100644 --- a/include/configs/o2dnt.h +++ b/include/configs/o2dnt.h @@ -137,17 +137,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif #endif @@ -276,7 +276,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* * For 66 MHz PCI clock additional Wait State is needed for CS0 (flash). */ diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h index fefdb3cca01..7151a9ec2e2 100644 --- a/include/configs/pf5200.h +++ b/include/configs/pf5200.h @@ -171,7 +171,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* * I2C configuration diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index b7f79c26eb9..23243a4971a 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -40,7 +40,7 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ /* Detect Sequoia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ - 3333333 : 33000000) + 33333333 : 33000000) #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -168,12 +168,19 @@ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ #define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ #undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + #ifdef CFG_ENV_IS_IN_NAND /* * For NAND booting the environment is embedded in the U-Boot image. Please take diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h index e106b3b5746..185c2d48709 100644 --- a/include/configs/smmaco4.h +++ b/include/configs/smmaco4.h @@ -138,17 +138,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -357,7 +357,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/spieval.h b/include/configs/spieval.h index f40dde2ac83..fd138a5d17a 100644 --- a/include/configs/spieval.h +++ b/include/configs/spieval.h @@ -219,17 +219,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#if defined(CFG_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't - * been tested with a IPB Bus Clock of 66 MHz. + * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -444,7 +444,7 @@ #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCISPEED_66 +#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index 8624f4b74b8..1978a32bb1e 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -80,16 +80,20 @@ * This address, however, is used to configure a 256M local bus * window that includes the Config latch below. */ -#define CFG_LBC_OPTION_BASE 0xf0000000 /* Localbus Extension */ +#define CFG_LBC_OPTION_BASE 0xF0000000 /* Localbus Extension */ #define CFG_LBC_OPTION_SIZE 256 /* 256MB */ /* There are various flash options used, we configure for the largest, * which is 64Mbytes. The CFI works fine and will discover the proper * sizes. */ -#define CFG_FLASH_BASE 0xFC000000 /* start of FLASH 64M */ -#define CFG_BR0_PRELIM 0xFC001801 /* port size 32bit */ -#define CFG_OR0_PRELIM 0xFC000FF7 /* 64 MB Flash */ +#ifdef CONFIG_STXSSA_4M +#define CFG_FLASH_BASE 0xFFC00000 /* start of 4 MiB flash */ +#else +#define CFG_FLASH_BASE 0xFC000000 /* start of 64 MiB flash */ +#endif +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | 0x1801) /* port size 32bit */ +#define CFG_OR0_PRELIM (CFG_FLASH_BASE | 0x0FF7) #define CFG_FLASH_CFI 1 #define CFG_FLASH_CFI_DRIVER 1 @@ -104,9 +108,9 @@ /* The configuration latch is Chip Select 1. * It's an 8-bit latch in the lower 8 bits of the word. */ -#define CFG_LBC_CFGLATCH_BASE 0xfb000000 /* Base of config latch */ -#define CFG_BR1_PRELIM 0xfb001801 /* 32-bit port */ -#define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ +#define CFG_LBC_CFGLATCH_BASE 0xFB000000 /* Base of config latch */ +#define CFG_BR1_PRELIM 0xFB001801 /* 32-bit port */ +#define CFG_OR1_PRELIM 0xFFFF0FF7 /* 64K is enough */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ @@ -300,17 +304,20 @@ /* Environment - default config is in flash, see below */ #if 0 /* in EEPROM */ -#define CFG_ENV_IS_IN_EEPROM 1 -#define CFG_ENV_OFFSET 0 -#define CFG_ENV_SIZE 2048 +# define CFG_ENV_IS_IN_EEPROM 1 +# define CFG_ENV_OFFSET 0 +# define CFG_ENV_SIZE 2048 #else /* in flash */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SECT_SIZE 0x40000 - -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +# define CFG_ENV_IS_IN_FLASH 1 +# ifdef CONFIG_STXSSA_4M +# define CFG_ENV_SECT_SIZE 0x20000 +# else /* default configuration - 64 MiB flash */ +# define CFG_ENV_SECT_SIZE 0x40000 +# endif +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) +# define CFG_ENV_SIZE 0x4000 +# define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) +# define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ diff --git a/include/configs/uc101.h b/include/configs/uc101.h index 8cd8e9be709..ff061eecc89 100644 --- a/include/configs/uc101.h +++ b/include/configs/uc101.h @@ -114,7 +114,7 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration diff --git a/include/configs/v38b.h b/include/configs/v38b.h index e19591d2993..0b7b19eadab 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -167,7 +167,7 @@ /* * IPB Bus clocking configuration. */ -#undef CFG_IPBSPEED_133 /* define for 133MHz speed */ +#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ #endif /* diff --git a/include/configs/xupv2p.h b/include/configs/xupv2p.h index a2f48102f0c..b4c720d18b5 100644 --- a/include/configs/xupv2p.h +++ b/include/configs/xupv2p.h @@ -132,6 +132,8 @@ CFG_CMD_LOADS |\ CFG_CMD_LOADB |\ CFG_CMD_MISC |\ + CFG_CMD_FAT |\ + CFG_CMD_EXT2 |\ CFG_CMD_PING \ ) @@ -163,12 +165,12 @@ "base 0;" \ "echo" - /* system ace */ -/*#define CONFIG_SYSTEMACE -#define DEBUG_SYSTEMACE -#define CFG_SYSTEMACE_BASE 0xCF000000 -#define CFG_SYSTEMACE_WIDTH 16 -#define CONFIG_DOS_PARTITION*/ +#define CONFIG_SYSTEMACE +/* #define DEBUG_SYSTEMACE */ +#define SYSTEMACE_CONFIG_FPGA +#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR +#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH +#define CONFIG_DOS_PARTITION #endif /* __CONFIG_H */ |